Installation manual GB/en

TROX GmbH
Heinrich-Trox-Platz
47504 Neukirchen-Vluyn
Germany
Phone: +49 (0) 2845 2020
Air terminal devices +49 (0) 2845 202-265
E-mail: [email protected]
http://www.troxtechnik.com
Ceiling diffusers

Product overview
A00000054447, 05/2017, © 2016 TROX GmbH

Fig. 1: Schematic illustration, VDW shown

A VDW-Q ⑦ Spigot
B VDW-R ⑧ Lip seal
① Diffuser face ⑨ Damper blade for volume flow rate balancing
② Central fixing screw with decorative cap ⑩ Pressure tap
③ Adjustable air control element (only VDW) ⑪ Green cord for closing the damper blade
④ Plenum box ⑫ White cord for opening the damper blade
⑤ Cross bar ⑬ Measuring tube
⑥ Suspension hole ⑭ Text label indicating plenum box variant
⑧ – ⑭: Optional equipment
This manual describes the - AIRNAMIC, VDW, TDV Silent Air, RFD, FD, TDF Silent Air, VD, VDL,
following product types: FDE, XARTO, ADD, DCS, VDR, ADLQ, DLQ, ADLR, DLQL, DLQ-AK,
Universal plenum box

Air terminal devices Ceiling diffusers 1

Important notes

Important notes Personal protective equipment

Information on the installation manual Personal protective equipment must be worn for all
work in order to reduce health or safety hazards to
This manual enables operating or service personnel the minimum.
to correctly install the product described below and
to use it safely and efficiently. The appropriate protective equipment for a job must
be worn for as long as the job takes.
It is essential that these individuals read and fully
understand this manual before starting any work. Industrial safety helmet
The basic prerequisite for safe working is to comply
with the safety notes and all instructions in this
manual.
The local regulations for health and safety at work
and general safety regulations also apply.
Qualified staff
Industrial safety helmets protect the head from
Skilled qualified electrician falling objects, suspended loads, and the effects of
Skilled qualified electricians are individuals who striking the head against stationary objects.
have sufficient professional or technical training,
knowledge and actual experience to enable them to Protective gloves
work on electrical systems, understand any poten-
tial hazards related to the work under consideration,
and recognise and avoid any risks involved.

Specialist personnel
Specialist personnel are individuals who have suffi-
cient professional or technical training, knowledge
and actual experience to enable them to carry out Protective gloves protect hands from friction, abra-
their assigned duties, understand any potential haz- sions, punctures, deep cuts, and direct contact with
ards related to the work under consideration, and hot surfaces.
recognise and avoid any risks involved.
Safety shoes
Limitation of liability
The information in this manual has been compiled
with reference to the applicable standards and
guidelines, the state of the art, and our expertise
and experience of many years.
The manufacturer does not accept any liability for
damages resulting from: Safety shoes protect the feet against crushing,
falling parts, and slipping on slippery ground.
 Non-compliance with this manual
 Incorrect use Correct use
 Operation or handling by untrained individuals Air terminal devices are used for the ventilation of
 Unauthorised modifications rooms in industrial and comfort areas. The air ter-
minal devices are connected to a supply air or
The actual scope of delivery may differ from the extract air system (by others), which is typically
information in this manual for special constructions, connected to an air handling unit.
additional order options or as a result of recent
technical changes.

2 Air terminal devices Ceiling diffusers

 Transport and storage

Air terminal devices supply cold or warm air to If the device has to be moved:
rooms (within the stated supply air to room air tem-
perature differences).  Be careful when unloading or moving the
product, and pay attention to the symbols and
Installation, operation and maintenance may have information on the packaging.
to meet increased hygiene requirements for certain  If possible, take the device in its transport
areas of application. packaging up to the installation location.
The installation of air terminal devices in humid  Use only lifting and transport gear designed for
rooms, areas with potentially explosive atmos- the required load.
pheres or rooms with dust-laden or aggressive air  Always secure the load against tipping and
has to be assessed for each individual case. falling.
Transport and storage  Do not move bulky items just by yourself. Get
help to prevent injuries and damage.
Delivery check
Upon delivery, carefully remove the packaging and Storage
check the unit for transport damage and complete- Please note:
ness. In case of any damage or an incomplete ship-
ment, contact the shipping company and your sup-  Store the unit only in its original packaging
plier immediately. Put the product back into its  Protect the unit from the effects of weather
packaging after the delivery check to protect it from  Protect the unit from humidity, dust and con-
dust and contamination. tamination
 Storage temperature: –10 to 50 °C
Fixing and installation material  Relative humidity: 95 % max., non-condensing

Fixing and installation material is not part of the

Packaging
supply package (unless stated otherwise), but
has to be provided by others; it has to be suitable Properly dispose of packaging material.
for the installation situation.

Transport on site

CAUTION!

Danger of injury from sharp edges, sharp cor-

ners and thin sheet metal parts!
Sharp edges, sharp corners and thin sheet metal
parts may cause cuts or grazes.
– Be careful when carrying out any work.
– Wear protective gloves, safety shoes and a
hard hat.

Air terminal devices Ceiling diffusers 3

Installation

Installation Ceiling diffusers

General information If possible, install the device before fixing the ceiling
tiles; if this is not possible, remove the adjacent
Personnel: ceiling tiles.
 Specialist personnel
Use only approved and adequately sized suspen-
Protective equipment: sion systems (fixing material is not included in the
 Industrial safety helmet supply package). Dimensions and weights are
 Protective gloves given in the technical leaflets.

 Safety shoes Only work in pairs; preferably use a lift.

Installation notes:
 Fix the device only to load-bearing structural
elements.
 Load suspension systems only with the weight
of the device. Adjacent components and con-
necting ducts must be supported separately.
 Use only approved and adequately sized fixing
material (fixing material is not included in the
supply package).
 Refer to the technical leaflets for product
weights and dimensions.
 The diffusers must remain accessible for
cleaning even after installation.
 Installation and sealing material which the
manufacturer provides is usually supplied in an
extra bag. Fig. 2: Plenum box (square/circular)

Before you install the device, take suitable precau- 1. Fix the suspension parts such as ropes,
tions to protect air distribution components from cables or metal hangers (Fig. 2/1) to the
contamination during installation (VDI 6022). If this ceiling.
is not possible, at least cover the devices or take
other precautions to protect them from contamina- 2. Use all of the available suspension points on
tion. In this case you have to ensure that the the plenum box.
devices cannot be activated. Ensure that the com-
ponents are clean before you install them. If neces-
sary, thoroughly clean them. If you have to interrupt
the installation procedure, protect all openings from
the ingress of dust or moisture.

4 Air terminal devices Ceiling diffusers

 Installation

Installation types

The optimum aerodynamic function is only ach-

ieved with flush ceiling installation

Installation without plenum box

Fig. 3: Flush ceiling installation with square plenum

box

Fig. 6: Flush ceiling installation with

standard cross bar G1, screw-fixed to ceiling

Fig. 4: Flush ceiling installation with circular plenum

box

Fig. 7: Flush ceiling installation with

duct cross bar E1
① Diffuser face
② Central fixing screw
③ Standard cross bar
④ Ceiling tile
⑤ Fixing tab
⑥ Duct cross bar
⑦ Duct
Fig. 5: Freely suspended installation
① Duct
② Suspension holes or lugs
③ Diffuser face
④ Extended border

Air terminal devices Ceiling diffusers 5

Installation

Ceiling systems Installing the diffuser face

In order to protect the surface of the diffuser face,

unpack and install it only after all other construc-
tion steps have been completed.
If there is a lengthy break between installation
and commissioning, cover all openings of the
casing (e.g. with plastic foil) to protect the interior
and avoid cumbersome cleaning procedures at
the time of commissioning.

Fig. 8: Ceiling systems

① Installation in T-bar ceilings
② Installation in T-bar ceilings, diffuser face rests
on T-bars
③ Installation into grid ceilings
④ Installation in continuous ceilings

Fig. 9: Installing the diffuser face

1. Glue the seal (Fig. 9/5) onto the reverse
edge of the plenum box.
2. Fix the diffuser face (Fig. 9/2) with the cen-
tral fixing screw (Fig. 9/3) to the cross bar
(Fig. 9/1) and cover it with the decorative
cap (Fig. 9/4).
The diffuser face and the fixing elements
may vary from the variant shown.

6 Air terminal devices Ceiling diffusers

 Installation

Air connection The diffuser has a spigot to connect it to the

ducting. Variants with a double lip seal allow for a
sufficiently tight connection; additional sealing is not
required.

Air terminal devices Ceiling diffusers 7

Electrical connection

Electrical connection

Personnel:
 Skilled qualified electrician

DANGER!

Danger of electric shock! Do not touch any live components! Electrical equipment carries a dangerous
electrical voltage.
– Only skilled qualified electricians are allowed to work on the electrical system.
– Switch off the power supply before working on any electrical equipment.

Order Type Supply voltage Max. Control input Wiring diagram Diffuser
code power signal type
rating

E1 NM230A 85 – 265 V AC, 6 VA 1-wire control or 2- Fig. 10, Fig. 11, VD, VDL,
50/60 Hz wire control (3- Fig. 12 VDR, DUK
point)

E2 NM24A 24 V AC ±20%, 50/60 4 VA 1-wire control or 2- Fig. 10, Fig. 11, VD, VDL,
Hz wire control (3- Fig. 12 VDR, DUK
1.5 W point)
24 V DC ±20%

E3 NM24A-SR 24 V AC ± 20%, 4 VA 2 – 10 V DC, Fig. 13 VD, VDL,

50/60 Hz Ra > 100 kΩ VDR, DUK
2W
24 V DC ± 20%

8 Air terminal devices Ceiling diffusers

 Electrical connection

Electric open/close actuators

Fig. 12: 2-wire control (3-point)

Fig. 10: 1-wire control S1 open and S2 open: Actuator has stopped (any
position)
S1 closed: Direction of rotation 1 S1 closed: Direction of rotation 1
open: Direction of rotation 2 S1 open, S2 closed: Direction of rotation 2

Modulating actuators

Fig. 11: 2-wire control (open/close)

S1 not actuated: Direction of rotation 1
S1 actuated: Direction of rotation 2 Fig. 13: Variable control
① Setpoint adjuster: U = voltage signal
0-10 V DC or 2-10 V DC
② Modulating actuator

Air terminal devices Ceiling diffusers 9

Commissioning, maintenance and cleaning

Commissioning, maintenance and cleaning Ceiling diffusers, variant -M

Initial commissioning The diffuser face can be removed to access the
damper blade (Fig. 15/1); the damper blade can
Before you start commissioning: then be set to any position between 0 and 90°
 Check that the air terminal devices are cor-
rectly seated. Ceiling diffusers, variant -MN
 Remove protective films, if any The diffuser face need not be removed since the
 Ensure that all air terminal devices are clean damper blade can be set with two cords (white and
and free from residues and foreign matter. green).
 Check that electrical connections (if any) have
been correctly made
 Ensure that the device has been correctly fixed
and connected to the ducting.
For commissioning see also VDI 6022, part 1 – 'Hy-
giene requirements for ventilation and air-condi-
tioning systems and units'.
Volume flow rate balancing
When several diffusers are connected to just one
volume flow controller, it may be necessary to bal-
ance the volume flow rates.

AIRNAMIC, XARTO Fig. 15: Damper blade, variant -MN

The diffuser face can be removed to access the ① Damper blade
damper blade; the damper blade can then be set in ② Cord: white cord for opening, green cord for
15° intervals between 0 and 90° closing
Once volume flow rate balancing is complete, put
the cords through the diffuser face into the plenum
box.

Fig. 14: Damper blade

① Damper blade
② Sticker explaining the damper blade position
③ Setting lever

10 Air terminal devices Ceiling diffusers

 Commissioning, maintenance and cleaning

Ceiling diffusers, variant -MN - volume flow rate 4. If necessary, adjust the damper blade posi-
measurement tion with the cords.
Ceiling diffusers with universal plenum box, damper
blade and pressure tap (variant -MN) allow for Volume flow rate calculation
volume flow rate balancing even with the diffuser
face in place.

Fig. 17: Volume flow rate calculation for air density

1.2 kg/m³

Fig. 18: Volume flow rate calculation for other air

densities
The K values are given in the technical leaflet for
the plenum box.
Maintenance and cleaning
Please note:
 The cleaning intervals given in the VDI 6022
standard apply.
 Clean surfaces with a damp cloth.
 Use only common household cleaners, do not
use any aggressive cleaning agents.
 Cleaning agents that contain chlorine must not
be used.
 Equipment for removing stubborn contamina-
tion, e.g. scrubbing sponges or scouring
cream, may damage the surfaces and must not
Fig. 16: Volume flow rate measurement
be used.
① Measuring tube  Replace contaminated equalising elements
② Pressure tap (fleece). For hygiene reasons you should not
③ Damper blade for volume flow rate balancing use a vacuum cleaner or wash the interior of
④ White cord for opening the damper blade the device.
⑤ Green cord for closing the damper blade
⑥ Digital manometer
⑦ Text label indicating plenum box variant
1. Connect the measuring tube to the digital
manometer.
2. Read the effective pressure.
3. Read the volume flow rate from the charac-
teristic curve or calculate it; each AK-Uni
plenum box comes with a characteristic
curve. The plenum box variant is given on
the text label (Fig. 16/7).

Air terminal devices Ceiling diffusers 11