Scribd
Upload
102 views

2.3.2.6 Packet Tracer - Configuring PAP and CHAP Authentication

k

Uploaded by

jbon lago
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
102 views

2.3.2.6 Packet Tracer - Configuring PAP and CHAP Authentication

k

Uploaded by

jbon lago
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Packet Tracer – Configuring PAP and CHAP Authentication

Topology

Addressing Table

Device Interface IP Address Subnet Mask Default Gateway

G0/0 192.168.10.1 255.255.255.0 N/A


R1
S0/0/0 10.1.1.1 255.255.255.252 N/A
G0/0 192.168.30.1 255.255.255.0 N/A
R2
S0/0/1 10.2.2.2 255.255.255.252 N/A
S0/0/0 10.1.1.2 255.255.255.252 N/A
R3 S0/0/1 10.2.2.1 255.255.255.252 N/A
S0/1/0 209.165.200.225 255.255.255.252 N/A
S0/0/0 209.165.200.226 255.255.255.252 N/A
ISP
G0/0 209.165.200.1 255.255.255.252 N/A
Web NIC 209.165.200.2 255.255.255.252 209.165.200.1
PC NIC 192.168.10.10 255.255.255.0 192.168.10.1
Laptop NIC 192.168.30.10 255.255.255.0 192.168.30.1

Objectives
Part 1: Review Routing Configurations
Part 2: Configure PPP as the Encapsulation Method
Part 3: Configure PPP Authentication

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 3
Packet Tracer – Configuring PAP and CHAP Authentication

Background
In this activity, you will practice configuring PPP encapsulation on serial links. You will also configure PPP
PAP authentication and PPP CHAP authentication.

Part 1: Review Routing Configurations


Step 1: View running configurations on all routers.
While reviewing the router configurations, note the use of both static and dynamic routes in the topology.

Step 2: Test connectivity between computers and the web server.


From PC and Laptop, ping the web server at 209.165.200.2. Both ping commands should be successful.
Remember to give enough time for STP and EIGRP to converge.

Part 2: Configure PPP as the Encapsulation Method


Step 1: Configure R1 to use PPP encapsulation with R3.
Enter the following commands on R1:
R1(config)# interface s0/0/0
R1(config-if)# encapsulation ppp

Step 2: Configure R2 to use PPP encapsulation with R3.


Enter the appropriate commands on R2:

R2(config)# interface s0/0/1


R2(config-if)# encapsulation ppp

Step 3: Configure R3 to use PPP encapsulation with R1, R2, and ISP.
Enter the appropriate commands on R3:

R3(config)# interface s0/0/0


R3(config-if)# encapsulation ppp
R3(config)# interface s0/0/1
R3(config-if)# encapsulation ppp
R3(config)# interface s0/1/0
R3(config-if)# encapsulation ppp

Step 4: Configure ISP to use PPP encapsulation with R3.


a. Click the Internet cloud, then ISP. Enter the following commands:
Router(config)# interface s0/0/0
Router(config-if)# encapsulation ppp
b. Exit the Internet cloud by clicking Back in the upper left corner or by pressing Alt+left arrow.

Step 5: Test connectivity to the web server.


PC and Laptop should be able to ping the web server at 209.165.200.2. This may take some time
as interfaces start working again and EIGRP reconverges.

Part 3: Configure PPP Authentication


Step 1: Configure PPP PAP Authentication Between R1 and R3.
Note: Instead of using the keyword password as shown in the curriculum, you will use the keyword secret to
provide a better encryption of the password.
a. Enter the following commands into R1:
R1(config)# username R3 secret class

© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 3
Packet Tracer – Configuring PAP and CHAP Authentication

R1(config)# interface s0/0/0


R1(config-if)# ppp authentication pap
R1(config-if)# ppp pap sent-username R1 password cisco
b. Enter the following commands into R3:
R3(config)# username R1 secret cisco
R3(config)# interface s0/0/0
R3(config-if)# ppp authentication pap
R3(config-if)# ppp pap sent-username R3 password class

Step 2: Configure PPP PAP Authentication Between R2 and R3.


Repeat step 1 to configure authentication between R2 and R3 changing the usernames as needed. Note that
each password sent on each serial port matches the password expected by the opposite router.

R2(config-if)# username R3 secret class


R2(config)# interface s0/0/1
R2(config-if)# ppp authentication pap
R2(config-if)# ppp pap sent-username R2 password cisco

R3(config-if)# username R2 secret cisco


R3(config)# interface s0/0/1
R3(config-if)# ppp authentication pap
R3(config-if)# ppp pap sent-username R3 password class

Step 3: Configure PPP CHAP Authentication Between R3 and ISP.


a. Enter the following commands into ISP. The hostname is sent as the username:
Router(config)# hostname ISP ISP(config)#
username R3 secret cisco ISP(config)#
interface s0/0/0 ISP(config-if)# ppp
authentication chap
b. Enter the following commands into R3. The passwords must match for CHAP authentication:
R3(config)# username ISP secret cisco
R3(config)# interface serial0/1/0
R3(config-if)# ppp authentication chap

Step 4: Test connectivity between computers and the web server.


From PC and Laptop, ping the web server at 209.165.200.2. Both ping commands should be successful.
Remember to give enough time for STP and EIGRP to converge.
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 3

You might also like