Scribd
Upload
86 views

10 Cu

1-phase transformer design

Uploaded by

Mahidhar Talapaneni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
86 views

10 Cu

1-phase transformer design

Uploaded by

Mahidhar Talapaneni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 6

1-PHASE TRANSFORMER DESIGN (CORE TYPE)

RATINGS CONDUCTOR DESIGN


KVA 5 HV CONDUCTOR 0 ROUND 0 REC 1
HV VOLTS 11000 6350 LV CONDUCTOR 0 ROUND 0 REC 1
LV VOLTS 460 DENSITY 2.9 DENSITY 3.1
HV AMPS 0.79 AREA 3.75 AREA 0.25
LV AMPS 10.87 DIA 2.19 DIA 0.564
RATIO 13.8 LENGTH 0 3 LENGTH 0 3
Bm 1.65 WIDTH 1.25 WIDTH 0.08
NLL CU COVERIN 0.25 COVERING 0.1
FLL 1 PARALLEL 1 PARALLEL 1
%Z AL DISPLACEME AXIAL RADIAL DISPLACEMENT AXIAL RADIAL
WINDING 1 2 1 1 1 1

CLEARENCES
CORE-LV 2.5 HV-HV 8 HV-YOKE 20 K 0.92
LV-HV 5 SPACERS 8 LV-YOKE 12

CORE DESIGN REC 1 ROUND 0


TURNSLV 214 GROSS A 60.51 OK W/H 105.13 145
EMF/TURN 2.15 DIA 91.5 93 W/W 65 core weight
Bm 1.65 MS 85 C/L 150.847988 150 34.13

LV COIL DESIGN HV COIL DESIGN


TURNS 214 TURNS 2953.2 DEN RESIST
TURNS/LIMB 107 TURNS/LIMB 1476.6 CU 8.9 0.021
LCOV 2.44 COILS/LIMB 1 AL 2.7 0.034
WCOV 2.44 turns/coil 1476.6 1477
N/LAYERS 3 LCOV 0.6643 (I^2 *R) 112.29 120
T/LAYER 35.6667 WCOV 0 UPF 0.8PF
HEIGHT 93.13 120 HEIGHT 125 EFFICIENCY
COIL HEIGHT 135 T/LAYER 173.99 172 REGULATION
PACKING 20.94 24.38 N/LAYERS 8.5872 9
ID 98 ID 124.64
B/LAYER 0.5 B/LAYER 0.125 %RESISTANCE 2.4
OD 114.64 DUCTS 1 %REACTANCE 0.6901
MD 106.32 120 OD 142.85 %IMPEDANCE 2.4973
RLV 0.40008 MD 133.74
LOSSES 47.2722 RHV 104.18 total losses 117.29
TEMP G LOSSES 65.02
WEIGHT(B) 2.38 TEMPG
WEIGHT© 2.55 WEIGHT(B) 2.7595
Rad thk 0.832 WEIGHT© 3.0906
Rad thk 0.9104
TANK
LENGTH 350 BODY
WIDTH 200 TOP
HEIGHT 540 BOTTOM
STIFFNER
CHANNEL NO
TOP 340 ANGLE
BOTTOM 320 FLAT
TIE ROD
CORE STUD
BASE PLATE
STEP STACK AREA FIG 1(LIMB) MASS FIG 2(YOKE) MASS
85 37.74 32.079 145 315 10.95 65 235 7.14 18.09
37.74 80 9.68 7.744 150 310 2.64 70 230 1.72 4.36
47.42 75 7.57 5.6775 155 305 1.94 75 225 1.26 3.2
54.99 65 11.52 7.488 165 295 2.56 85 215 1.67 4.23
66.51 55 8.48 4.664 175 285 1.59 95 205 1.04 2.63
74.99 45 6.4 2.88 185 275 0.98 105 195 0.64 1.62
81.39 11.61 0 195 265 0 115 185 0 0
93 0 0 205 255 0 125 175 0 0
60.5325 20.66 13.47 34.13

RECTANGLE
CORE
WIDTH
THICK
W/H
W/W
SIST C/L
WEIGHT

WINDING
LV HV
INNER DIMENSSIONS INNER DIMENSSIONS
LENGTH WIDTH LENGTH WIDTH

B/L B/L
DUCTS DUCTS
OUTER DIMENSSIONS OUTER DIMENSSIONS
LENGTH WIDTH LENGTH WIDTH
WEIGHT ANALYSIS
DIA AREA OHM’S
Medium AT
SWG (mm) (sqmm) 20DEG
mm mm 23.5 0.584 0.2681
44 0.081 0.00519 0.106 0.015 3322.8 23 0.61 0.2919
43 0.091 0.00657 0.117 0.015 2626 22.5 0.66 0.3425
42 0.102 0.00811 0.13 0.018 2127 22 0.711 0.3973
41 0.112 0.00981 0.13 0.02 1758 21.5 0.762 0.4561
40 0.122 0.00117 0.142 0.02 1477 21 0.813 0.5189
39 0.132 0.0137 0.168 0.023 1258 20.5 0.864 0.5857
38 0.152 0.01824 0.188 0.023 945.2 20 0.914 0.6567
37 0.173 0.02343 0.213 0.028 735.9 19.5 0.965 0.7137
36 0.193 0.2927 0.236 0.028 589.1 19 1.016 0.8107
35 0.213 0.03575 0.259 0.03 482.2 18.5 1.118 0.981
34 0.234 0.04289 0.282 0.03 402 18 1.219 1.167
33 0.254 0.05067 0.305 0.033 340.3 17.5 1.321 1.37
32.5 0.264 0.05481 0.315 0.033 314.5 17 1.422 1.589
32 0.274 0.0591 0.328 0.033 291.7 16.5 1.524 1.824
31.5 0.284 0.06356 0.338 0.033 271.2 16 1.626 2.075
31 0.295 0.06818 0.348 0.033 252.9 15.5 1.727 2.343
30.5 0.305 0.07297 0.358 0.036 236.3 15 1.829 2.627
30 0.315 0.07791 0.371 0.038 221.2 14.5 1.93 2.92
29.5 0.33 0.08553 0.387 0.038 201.6 14 2.032 3.243
29 0.345 0.09372 0.404 0.041 183.97 13.5 2.2 3.8014
28.5 0.36 0.10179 0.419 0.041 169.39 13 2.34 4.3005
28 0.376 0.111 0.434 0.041 155.34 12.5 2.5 4.9087
27.5 0.396 0.1233 0.462 0.043 139.8 12 2.64 5.4739
27 0.417 0.1363 0.483 0.043 126.51 11.5 2.8 6.1575
26.5 0.437 0.1499 0.505 0.046 115 11 2.95 6.8349
26 0.457 0.1642 0.526 0.046 105.02 10.5 3.1 7.5477
25.5 0.483 0.1829 0.554 0.048 94.25 10 3.25 8.2958
25 0.508 0.2027 0.579 0.048 85.67 9.5 3.45 9.3482
24.5 0.533 0.2235 0.605 0.048 77.15 9 3.66 10.51
24 0.559 0.2452 0.632 0.048 70.3 8.5 3.86 11.7021
8 4.06 12.97
8 4.06 12.97
0.66 0.051 64.31
0.686 0.051 59.07
0.739 0.051 50.33
0.792 0.053 43.4
0.843 0.053 37.8
0.897 0.056 33.23
0.947 0.056 29.43
1.006 0.058 26.26
1.057 0.058 23.56
1.11 0.061 21.27
1.212 0.061 17.576
1.318 0.063 14.768
1.42 0.063 12.584
1.529 0.066 10.85
1.631 0.066 9.451
1.735 0.069 8.307
1.839 0.069 7.358
1.943 0.071 6.564
2.047 0.071 5.89
2.151 0.071 5.317
2.325 0.074 4.536
2.465 0.076 4.02
2.631 0.081 3.512
2.775 0.081 3.146
2.935 0.084 3.8
3.09 0.084 2.529
3.245 0.084 2.284
3.395 0.084 2.077
3.6 0.086 1.839
3.81 0.089 1.6404
4.015 0.089 1.4731
4.215 0.089 1.3287
4.215 0.089 1.3287

You might also like