SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.01 – JAN ‘05

SCW 14 B WATER COOLER
NEW FOOT PEDAL CABLE
Starting from SCW 14 B s.n. 6798, the previous food pedal cable has been replaced
with a new one made by Stainless Steel for a longer last.

Moreover, the inside part of the sheath is covered in teflon so to allow a better sliding.
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.02 – JAN ‘05

ACM 85 – ICE THREE
NEW COMPRESSOR
Starting from the following serial numbers:

ACM 85 S.N. 32179

ICE THREE 4523

the previous Tecumseh compressors at 230/50/1 and 230/60/1 (CAE 4448 Y,

respectively our Part Nbrs 670101 00 and 670101 02) have been replaced with the
Cubigel GP 14 TB available under Part Numbers:

670100 01 230/50/1
670100 08 230/60/1

already used on models ACM 105, MF 22 and AF 200.

These new compressors are exchangeable with the former ones as assembly with their
own electrical boxes and starting devices.

The Part Numbers of the starting devices are:

Starting relay P/N 620057 56 230/50/1

Starting relay P/N 620057 67 230/60/1
Protector 620058 67 230/50/1
Protector 620058 98 230/60/1
Starting capacitor 620167 29 230/50-60/1
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.03 – MARCH ‘05

MF SERIES
NEW GEAR REDUCER
PLASTIC DRIP TRAY
Starting from the following serial nbrs:
MF 41 S.N. 014289
MF 51 019658
MF 52 SPLIT 001180
MFE 61 004800
MF 62 SPLIT 001215
the previous gear reducer metal drip tray P/N 650686 00 has been replaced with a new
plastic one of different shape and equipped with an overflow at lower level the output
shaft oil seal, as detailed on the bottom photo.

The new plastic drip tray is available under P/N 660755 00 and it’s exchangeable with
former one with partial modification of the plastic drain hose.

The new plastic drip tray will be supplied in place of former one as soon as we’ll run
out of stock.
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.04 – MARCH ‘05

MV SERIES
NEW PC BOARD & SENSORS
KIT FOR VERY SOFT WATER
A new PC Board & Sensors Kit, for the New/Current MV Series machines, is now
available as service part under Part Nbr CM 81453901.

This new PC Board & Sensors Kit, that works in the same way of the current standard
one, allows the correct operation of the MV Series even when water is very soft and/or
de-mineralized, like the one coming from the Reverse Osmosis water treatment system.

The major components of the new PC Board & Sensors Kit are:

PC Board P/N CM 33580171

Water level sensor CM 81453860
Ice thickness sensor CM 81453782
Ice thickness sensor bracket CM 25725527

Some of these PC Board & Sensors Kits have been installed on some MV units already
installed in the field for test.

The new PC Board is equipped with a DIP Switches for the proper setting of the unit as
detailed here below:

Standard setting

Start up delay time ON

Attached please find the installation instruction.

PURE WATER BOARD

INSTALLATION KIT
KIT DI INSTALLAZIONE

PURE WATER BOARD N EW WATER LEVEL SENSOR WITH

S CHEDA PER ACQUA CONNECTION WIRE TO THE BOARD
DEMINERALIZZATA SENSORE DI LIVELLO ACQUA CON FILO
DI COLLEGAMENTO ALLA SCHEDA

GROUND CABLE
CAVO DI TERRA

ICE SENSOR SUPPORT NEW ICE SENSOR WITH CONNECTION

S UPPORTO SENSORE WIRE TO THE BOARD
GHIACCIO SENSORE GHIACCIO CON FILO DI COL-
LEGAMENTO ALLA SCHEDA
PURE WATER BOARD

DRILL THE UPPER EVAPORATOR FRAME AS PER ENCLOSED DRAWING; THEN FIX THE ICE
SENSOR SUPPORT TO THE FRAME BY THE SCREWS
FORARE LA CORNICE SUPERIORE DELL’EVAPORATORE COME DA DISEGNO ALLEGATO;
POI FISSARE IL SUPPORTO SENSORE GHIACCIO ALLA CORNICE CON LE VITI

SET THE ICE SENSOR TO THE SUPPORT

AND CONNECT THE WIRE TO THE BOARD
(BOARD CONNECTOR “ICE SENSOR”)
POSIZIONARE IL SENSORE GHACCIO SUL
SUPPORTO E COLLEGARE IL FILO ALLA
SCHEDA (CONNETTORE DELLA SCHEDA
“ICE SENSOR”)
PURE WATER BOARD

REPLACE THE WATER LEVEL SENSOR

AND CONNECT THE WIRE TO THE BOARD
(BOARD CONNECTOR “WATER LEV.”)
N OTE : THE NEW SENSOR IS
INTERCHANGEABLE WITH THE OLD ONE
SOSTITUIRE IL SENSORE DI LIVELLO
ACQUA E COLLEGARE IL FILO ALLA
SCHEDA (CONNETTORE DELLA SCHEDA
“WATER LEV.”)
N O TA : IL NUOVO SENSORE È
INTERCAMBIABILE CON IL VECCHIO

REPLACE THE BOARD

NOTE: THE BOARD CONNECTORS ARE
THE SAME (EXCEPT ICE AND WATER
LEVEL SENSOR CONNECTORS)
THEN CONNECT THE GROUND CABLE
TO THE BOARD (BOARD CONNECTOR
“GND”) AND TO THE GROUND TERMINAL
SOSTITUIRE LA SCHEDA
NOTA: I CONNETTORI DELLA SCHEDA
SONO GLI STESSI ( E C C E T T O I
CONNETTORI DEI SENSORI GHACCIO E
ACQUA)
POI COLLEGARE IL CAVO DI TERRA ALLA
SCHEDA (CONNETTORE DELLA SCHEDA
“GND”) E AL MORSETTO DI TERRA
PURE WATER BOARD

ICE SENSOR CONNECTOR

CONNETTORE SENSORE GHIACCIO

WATER LEVEL SENSOR CONNECTOR

CONNETTORE SENSORE DI LIVELLO
ACQUA

GROUND CONNECTOR
CONNETTORE DI TERRA
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.05 – APRIL ‘05

MAR - MF SPLIT SERIES
COS - CONDENSING UNITS
SPARE PARTS LIST
Attached please find the chart showing the Part Numbers of the major components used
on the following Scotsman-COS condensing units:

CONDENSING UNIT SPLIT UNIT

UCM 52 MF 52
UC 071 MAR 071
UCM 62 MF 62
UC 101 MAR 101
UC 121 MAR 121
UC 201 MAR 201
UC 202 MAR 201
UC 301 MR 301
 UCM 52 UC 071 UCM 62 UC 101 UC 121 UC 201 UC 202 UC 301
CONDENSING UNIT/COMPONENT
SL1366 C8 SL 1406 C25 SM 1456 C70 SL 1456 C45 SM 2456 C130 SM 2456 C150 SL2406C65 SL 4406 C110
FAN SPEED CONTROL COS 3338002 COS 3338002 COS 3338002 COS 3338002 COS 3338002 COS 3338002 COS 3338002 COS 3338002
FAN MOTOR COS 3021504 COS 9321570 COS 9321575 COS 9321575 COS 9321575 COS 9321575 COS 9321570 COS 9321570
FILTER COS 3326196 COS 3326196 COS 3326196 COS 3326196 COS 3326205 COS 3326205 COS 3326205 COS 3326220
SOLENOID VALVE BODY COS 1530446 COS 1530446 COS 1530446 COS 1530446 COS 1530446 COS 1530460 COS 1530455 COS 1530460
SOLENOID VALVE COIL COS 1530560 COS 1530560 COS 1530560 COS 1530560 COS 1530560 COS 1530560 COS 1530560 COS 1530560
CONDENSER COIL COS 7840110 COS 7840101 COS 7840101 COS 7840101 COS 7840101 COS 7840107RI COS 7840107RI COS 7840104
DOUBLE PRESSURE SWITCH COS 3332025 COS 3332025 COS 3332025 COS 3332025 COS 3332025 COS 3332025 COS 3332025 COS 3332025
CURRENT RELAY COS 2619416 COS 2619416 COS 2619416 COS 2619416 COS 2619416 COS 2619416 COS 2619416 COS 2619416
INJECTION SOLENOID VALVE COS 99933796 COS 99933796 COS 99933796 COS 99933796 COS 99933796
SAFETY RELIEF VALVE COS 99943008 COS 99943008 COS 99943008 COS 99943008 COS 99943008 COS 99943008 COS 99943008 COS 99943008
CRANCASE HEATER COS 2619501 COS 2619501 COS 2619501 COS 2619501 COS 2619501 COS 2619501 COS 2619502 COS 2619502
DISCHARGE LINE TSTAT COS 2619154 COS 2619154 COS 2619154 COS 2619154 COS 2619154 COS 2619154 COS 2619154 COS 2619154
KRIWAN COS 2619409 COS 2619409 COS 2619409 COS 2619409 COS 2619409 COS 2619409 COS 2619409 COS 2619409
COMPRESSOR COS CAJ2464Z COS ZF09 COS ZB26 COS ZF15 COS ZB45 COS ZB56 COS ZF24 COS ZF40
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.06 – MAY ‘05

MFE 61
NEW COMPRESSOR
CURRENT RELAY
Starting from MFE 61 s.n. 04879 the previous compressor current relay P/N 620428 00
(9-15 amps) has been changed with a new smaller one (6-10 amps) as the former one
was oversized for the current drown by the MFE 61 compressor.

The new Compressor Current Relay is the same of the one used on MC 1210 and it's
available under P/N 620428 02.

On MFE 61 it is set up to the minimum setting i.e. 6 amps as shown on photo below
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.07 – MAY ‘05

TC 180
NEW MEMBRANE SWITCH
DISPENSING PANEL
Starting from TC 180 s.n. 02988 a new Membrane Switch Dispensing Panel is installed
in place of the former one.

The new Membrane Switch Dispensing Panel, NOT exchangeable with the former one,
is composed by:

Membrane Switch Panel P/N 620483 00

Display Board 620483 03
Plastic box cover 660699 00
Plastic box back 660700 00

as detailed on the bottom picture.

660699 00
660700 00

620483 03
620483 00
To allow the installation of the new Membrane Switch Dispensing Panel on the old
machines, a retrofit kit is available under Part Nbr 060613 00 and it is supplied already
pre-assembled as shown on the photo below.

The new Membrane Switch is studied to support up to 1 million pushes to each of the
four Switches.

Once we will run out of stock of the former Dispensing Board, we will automatically
supply the new retrofit kit.
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.08 – MAY ‘05

AC 225
NEW STAINLESS STEEL
BRACKET FOR ICE LEVEL
CONTROL
To avoid any deformation of the Optical Ice Level Control Plastic Bracket installed
inside the storage bin, starting from s.n. 51504 a new S.S. bracket is fitted located
behind the plastic one, as detailed on the bottom photos.

The new metal bracket can be retrofitted on the former machines and it's available under
Part Nbr 722008 00.
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.09 – JUNE ‘05

MC 1210 - MFE 61 - MAR 205
NEW FAN MOTOR
Starting from the following Serial Nbrs:

MC 1210 S.N. 3358

MFE 61 4894
MAR 205 2506

the previous fan motor P/N 620273 00 of 100 Watts has been replaced with a more
powerfull one (130 Watts) available under new Part Nbr 620490 00.

This new fan motor is perfectly exchangeable with all the former ones (old Part Nbr
620273 00 and Part Nbr 620273 03) and will be supplied in place of them once we'll run
out of stock of the previous ones.
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.10 – SEPT. ‘05

TC 180
NEW FRONT & TOP PANELS
Starting from the TC 180 serial nbr 3071, the Front and Top plastic panels have been
changed on their top matching connection from flat to round (as shown on the bottom
photo) in order to facilitate the removal of the storage bin cover w/out the need, as in the
former version, to remove also the front panel.

The new Top and Front panel are available under the following part nbrs:

Top panel P/N 660811 00

Front panel (Push buttons switches version) 660812 00
Front panel (Dispensing board version) 660812 01

and they are not exchangeable with the former ones as single piece.

Two new retrofit kits, consisting of the new Front + Top Panels, are also available under
the following part nbrs:

Front/Top Panels Kit (Switches) P/N 060600 02

Front/Top Panels Kit (Board) P/N 060600 03

As soon as we'll run out of stock of former Front Panel/Front Panel Kit as well as of the
former Top Panel, we will supply the new corresponding Front/Top Panel Kit.
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.11 – SEPT. ‘05

MAR 55 - 75 - 105 - 125
NEW "G" VERSIONS &
CONTROL BOX
Starting from the following serial nbrs:

MAR 55 S. N. 01755
MAR 75 01247
MAR 105 02709
MAR 125 01257

the control box has been changed in most of the electric components as well as in its
wiring connections.

Moreover, in addition to the electrical components used till now, there are two time
delay relais to:

a Delay the start up of compressor by 18' at every start up of machine

b Delay the stop of the drum by 18' at every stop of the machine

as well as a 3-phase monitoring relay on the power in a drum rotation electronic control
board (it operates using the Hall effect sensor/principle as done on our Flaker
machines).

In case the drum is not rotating at all (or it rotates too slow - lees then 1/4 turn every
30"), the new electronic control board trips off the entire machine so to avoid that, in
case of breakage of the fiber keys, the drive motor/gear reducer and compressor can
operate with the drum off.

Attached you can find a short presentation of the operation of components of the new
control box as well as the new wiring diagram.

Starting from November 2005, all the MAR Split as well as the MAR 205-305 will be
equipped with this new control box.

The spare list of the MAR 55-75-105-125 control box in Internet will be soon modified
accordingly.
MAR SERIES
NEW
CONTROL BOX
 SAFETY
SAFETY HI
HI
PRESSURE
PRESSURE CONTROL
CONTROL

FAN
FAN
PRESSURE
PRESSURE
CONTROL
CONTROL 230-400V
230-400V IN
IN -- 12V
12V OUT
OUT
TRANSFORMER
TRANSFORMER
 EVAPORATOR
EVAPORATOR DRUM
DRUM
ROTATION
ROTATION CONTROL
CONTROL
PC BOARD
PC BOARD
230-400V
230-400V IN
IN -- 12V
12V OUT
OUT
TRANSFORMER
TRANSFORMER

EVAPORATOR
EVAPORATOR DRUM
DRUM
ROTATION
ROTATION CONTROL
CONTROL
RESET
RESET BUTTON
BUTTON

BIN
BIN THERMOSTAT
THERMOSTAT
 3-PHASE
3-PHASE
COMPRESSOR
COMPRESSOR
MONITORING
MONITORING
START
START UP
UP DELAY
DELAY
RELAY
RELAY
CONTROL
CONTROL

TERMINAL
TERMINAL
BOARD
BOARD

FUSE
FUSE
HOLDER
HOLDER

EVAPORATOR
EVAPORATOR DRUM
DRUM DRIVE
DRIVE MOTOR
MOTOR
ROTATION
ROTATION CONTROL
CONTROL TRIP
TRIP OFF DELAY
OFF DELAY
LOW
LOW POWER
POWER RELAY
RELAY CONTROL
CONTROL

REMOTE
REMOTE ICE
ICE LEVEL
LEVEL CONTROL
CONTROL
LOW
LOW POWER RELAY
POWER RELAY
(TIMER - OPTICAL SENSOR)
(TIMER - OPTICAL SENSOR)
 COMPRESSOR
COMPRESSOR DRIVE
DRIVE MOTOR
MOTOR
START
START UP
UP DELAY
DELAY TRIP
TRIP OFF DELAY
OFF DELAY
CONTROL
CONTROL CONTROL
CONTROL

3-PHASE
3-PHASE
MONITORING
MONITORING RELAY
RELAY

FUSE
FUSE COMPRESSOR
COMPRESSOR
HOLDER
HOLDER CONTACTOR
CONTACTOR

DRIVE
DRIVE
MOTOR
MOTOR
CONTACTOR
CONTACTOR

COMPRESSOR
COMPRESSOR
CURRENT
CURRENT
PROTECTOR
PROTECTOR
EVAPORATOR
EVAPORATOR DRUM
DRUM REMOTE
REMOTE ICE
ICE LEVEL
LEVEL CONTROL
CONTROL
ROTATION CONTROL
ROTATION CONTROL LOW
LOW POWER
POWER RELAY
RELAY
LOW
LOW POWER
POWER RELAY
RELAY (TIMER
(TIMER - OPTICAL SENSOR)
- OPTICAL SENSOR)
METAL
METAL BRACKET
BRACKET MAGNET
MAGNET (HALL
(HALL
EFFECT) SENSOR
EFFECT) SENSOR

PLASTIC
PLASTIC DISK
DISK
SECURED
SECURED MAGNET
MAGNET CILINDER
CILINDER
DIRECTLY
DIRECTLY TO
TO THE
THE (FOUR
(FOUR PIECES
PIECES PER
PER
EVAPORATOR
EVAPORATOR PLASTIC DISK)
PLASTIC DISK)
DRUM
DRUM SHAFT
SHAFT PLACED
PLACED ATAT 1/4
1/4
TURN
TURN EACH
EACH
 MAGNET
MAGNET (HALL
(HALL MAGNET
MAGNET (HALL
(HALL
EFFECT)
EFFECT) SENSOR
SENSOR WITH
WITH EFFECT)
EFFECT) SENSOR WITH
SENSOR WITH
OPEN CONTACTS
OPEN CONTACTS CLOSED
CLOSED CONTACTS
CONTACTS
RED
RED LED
LED OFF
OFF RED
RED LED
LED ON
ON

EVAPORATOR
EVAPORATOR DRUM
DRUM ROTATION
ROTATION CONTROL
CONTROL BOARD
BOARD MUST
MUST RECEIVE
RECEIVE THE
THE SIGNAL
SIGNAL OF
OF
SENSOR
SENSOR CONTACTS
CONTACTS CHANGE
CHANGE (OPEN
(OPEN OR
OR CLOSE)
CLOSE) WITHIN
WITHIN A
A PREFIXED
PREFIXED TIME
TIME

IF
IF NOT
NOT (RED
(RED LED
LED ALWAYS
ALWAYS OFF
OFF OR
OR ON)
ON) THE
THE DRUM
DRUM ROTATION
ROTATION
CONTROL BOARD SWITCHES OFF THE MACHINE
 KT2
KT2 -- DRIVE
DRIVE MOTOR
MOTOR
KT1
KT1 -- TRIP OFF DELAY
TRIP OFF DELAY
COMPRESSOR
COMPRESSOR CONTROL
CONTROL
START
START UP
UP
DELAY
DELAY TIMES
TIMES TO
TO MULTIPLIED
MULTIPLIED THE
THE
CONTROL
CONTROL RANGE SETTING
RANGE SETTING
EXAMPLE:
EXAMPLE: SETTING
SETTING AT
AT 0,1
0,1
HR
HR RANGE
RANGE (6(6 MINUTE)
MINUTE)
MULTIPLIED
MULTIPLIED BY 33 TIMES
BY TIMES
EQUAL
EQUAL TO
TO 18
18 MINUTES
MINUTES
DELAY
DELAY TIME
TIME

OFF
OFF -- OPEN
OPEN CONTACTS
CONTACTS
ON - CLOSED CONTACTS
ON - CLOSED CONTACTS
BLINKING
BLINKING -- DELAY
DELAY TIME
TIME ON
ON

POWER
POWER ON
ON

RANGE
RANGE SETTING
SETTING SCREW
SCREW
FROM
FROM 0,1 SECOND TO 10
0,1 SECOND TO 10 HRS
HRS SETTING
SETTING FOR
FOR BOTH
BOTH DELAY
DELAY CONTROLS
CONTROLS --
18
18 MINUTES
MINUTES
EV1 FAN MOTOR MOTEUR VENTILATEUR VENTILATORE
EV2 FAN MOTOR MOTEUR VENTILATEUR VENTILATORE
F1 3-PHASE MONITORING RELAY CONTROL SEQUENCE PHASE CONTROLLO SEQ. FASI
FC1 SPOUT SWITCH INTERRUPTEUR BEC VERSEUR INTERR. BOCCHETTA
FR1 COMPRESSOR RELAY RELAIS AMPEROMETRIQUE COMPRESSEUR 7-10 AMPS RELE' COMPRESSORE
FU2 FUSE FUSIBLE FUSIBILE
FU3 FUSE FUSIBLE FUSIBILE
HL1 GREEN LIGHT TEMOIN VERT LUCE VERDE
HL2 RED LIGHT TEMOIN ROUGE LUCE ROSSA
HL3 RED LIGHT TEMOIN ROUGE LUCE ROSSA
HL4 RED LIGHT TEMOIN ROUGE LUCE ROSSA
HL5 RED LIGHT TEMOIN ROUGE LUCE ROSSA
HL6 RED LIGHT TEMOIN ROUGE LUCE ROSSA
HL7 RED LIGHT TEMOIN ROUGE LUCE ROSSA
HL8 RED LIGHT TEMOIN ROUGE LUCE ROSSA
KA1 RELAY-DRUM ROTATION CONTROL RELAIS - CONTROL ROTATION CYLINDRE RELE'-CONTROLLO ROTAZ.
KA2 RELAY-ICE LEVEL CONTROL RELAIS - CONTROL NIVEAU GLACE RELE'-CONTROLLO LIVELLO GHIACCIO
KM1 CONTACTOR-COMPRESSOR CONTACTEUR - COMPRESSUER TELERUTTORE-COMPRESSORE
KM2 CONTACTOR-DRIVE MOTOR/WATER PUMP CONTACTEUR - MOTEUR REDUCTEUR + POMPE A EAU TELERUTTORE-RIDUTTORE
KT1 TIME DELAY-COMPRESSOR TIMER - DELAI DEMARRAGE COMPRESSEUR RITARDATORE-COMPRESSORE
KT2 TIME DELAY-DRIVE MOTOR/WATER PUMP TIMER - DELAI ARRETE MOTEUR REDUCTEUR/POMPE A EAU RITARDATORE-RIDUTTORE
PT1 TIMER 0-24 HR - 24V TIMER 0-24 HR - 24V TIMET 0-24 HR - 24V
SA1 SWITCH INTERRUPTEUR INTERRUTTORE
SB1 RE-SET PUSH BUTTON BOUTON RE-ENCLANCHEMENT PULSANTE RE-SET
SP1 HI PRESSURE CONTROL PRESSOSTAT HP PRESSOSTATO DI ALTA
SP2 HI PRESSURE CTRL-SAFETY PRESSOSTAT HP - SECURITE' PRESS. DI ALTA - SICUREZZA
SP3 LO PRESSURE CONTROL PRESSOSTAT BP - SECURITE' PRESSOSTATO DI BASSA
SP4 HI PRESSURE CONTROL PRESSOSTAT HP PRESSOSTATO DI ALTA
SQ1 DRUM ROTATION CONTROL BOARD CARTE ELECTONIQUE CONTROL ROTATION CYLINDRE SCHEDA CONTROLLO ROTAZIONE
ST1 THERMOSTAT THERMOSTAT TERMOSTATO
T2 TRANSFORMER TRANSFORMATEUR 0-230/400V 0-24V TRASFORMATORE
TM2 DRIVE MOTOR THERMAL PROTECTOR INTERRUPTEUR THERMIQUE MOTEUR REDUCTEUR PROTETTORE TERMICO MOTORE
X1 TERMINAL BOARD BORNIER MORSETTIERA
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.12 – NOV. ‘05

MF 41 - MF 51/52 - MF 62 - MFE 61

NEW AUGER WITH O RING

ON THE LOWER SHAFT
Starting from the following serial nbrs:

MF 41 S. N. 14613
MF 51 20397
MF 52 SPLIT 01266
MFE 61 01327
MF 62 SPLIT 04949

the bottom shaft of the auger is now equipped with a groove and a small O Ring Part
Nbr 640041 34, in order to increase the friction with the inner ring of the lower bearing
as shown on the attached photo/drawing.

The friction made by the O Ring, assures the correct/proper transmission of the rotation
to the inner ring of the lower bearing.

The new augers are perfectly exchangeable with the former ones in all the above listed
machines and are available under the same part nbrs:

Short one MF 41 P/N 724198 02

Long one MF 51/52/62-MFE 61 724198 03
 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.13 – NOV. ‘05

MF 82
NEW COMPRESSOR
Starting from the serial nbr 3836, the model MF 82 is now equipped with a new Bitzer
compressor model 4DC-5.2Y and available under Part Nbr 670103 00.

Compared with former Dorin compressor, the new Bitzer Model 4DC-5.2Y is much
more quiet/silent and less vibrating with the vantage of much less vibrations transmitted
to the unit frame as well as to the refrigerant system.

The new compressor can be installed in place of former one with some modifications on
the refrigerant system.

The same compressor will be shortly installed also on MAR 205.

 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.14 – NOV. ‘05

MV 300 - MV 450 - MV 600
MV 800 - MV 1000
RESISTANCE TO BE CUTTED
ON PC BOARD ONLY ON
UNITS OPERATING AT 60 HZ
We would like to inform you that when PC Board P/N CM 33580150 is used on units
operating at 60Hz only, the small resistance shown on the here below drawing MUST
be removed.

J2

J1

Failing in doing it there is the possibility that compressor contactor coil can stay
energized, even with the machine OFF, keeping the compressor running.

This operation is NOT needed on units operating at 50hz.

 SCOTSMAN EUROPE SERVICE DEPARTMENT

SP-05.15 – DEC. ‘05

MV 300 - MV 450 - MV 600
MV 800 - MV 1000
TESTING CABLE
We would like to inform you that a Testing Cable, to test the operation of the current
version of MV series, is available under Part Nbr CM 29015064.

With this simple cable, installed directly to the Jumper J1 of the PC Board, it's possible
to made a diagnosis of the correct operation of the probes as well as of the entire
machine as detailed on the attached instructions.
 MV 300 – 450 – 600 – 800 - 1000
TESTING CABLE USE
1. Turn the unit OFF

2. Drain water from water reservoir till the two metal plates of the water level sensor are no longer in contact
with water

3. Plug “testing cable” to its male socket “J1” with transparent plug cover facing down

J2

J1

4. Turn the unit ON

5. All LEDs blink together with machine in stand by mode

ALARM
BIN
HI
POWER OPER. FULL ALARM RE-SET
PRESS.
6. If any sensor/switch is in trouble/out of order the monitoring panel will inform as per below table:

LED 5
LED 1 LED 2 LED 3 LED 4
HI PRESS.
POWER OPERATION BIN FULL ALARM
ALARM
Probe temperature error ON ON

Ice thickness sensor error FAST BLINK ON ON

Water level sensor error FAST BLINK ON ON

Magnetic switch error FAST BLINK ON ON

RESET push button error FAST BLINK FAST BLINK FAST BLINK ON ON

Too hi discharge pressure error ON

UNIT OPERATION TESTING

With testing cable plugged IN and all LEDs blinking together, PUSH Reset Button for a while then following
phases automatically take place:

‰ Water dumping
• 1ST GREEN LED (POWER) ON steady and 2ND GREEN LED (OPERATION) blink
• Water pump ON
• Drain valve ON

‰ Water filling
• 3RD YELLOW LED (BIN FULL) ON steady
• Water inlet valve ON
• Water pump OFF (ON after 20")
• Compressor ON

‰ Freezing Cycle
• Both 2ND GREEN LED (OPERATION) and 3RD YELLOW LED (BIN FULL) ON steady (1ST LED -
POWER - blinks when circuit is shorted between the two metal plates of the Ice Thickness Sensor)
• Water pump ON
• Compressor ON

In case during one of the above listed phases any trouble occurred due to wrong operation and/or
sensors/switches trouble, the machine stops with glowing of the LED's as per here below chart:

LED 5
LED 1 LED 2 LED 3 LED 4
HI PRESS.
POWER OPERATION BIN FULL ALARM
ALARM
Probe temperature error ON ON
Water level sensor error SLOW BLINK SLOW BLINK
Too hi condenser temp error SLOW BLINK
Too long freezing cycle ON SLOW BLINK
Too long defrost cycle ON FAST BLINK
Too hi discharge pressure error ON

Once 4 full testing cycles are completed without report any failure, all LEDs glow together with machine OFF.