Introduction

The scope of this calculation is to analyse the cuplock scaffolding system in Marquise Square Tower project,
,the steel beam to pipe connection and support bracket.
The steel frame is modeled in STAAD to obtain the exact results applying the necessary dead load and live
load.

Loadings
Dead Load
The self-weight of the memberes will be automatically calculated by STAAD software.

Live Load
The live loads are applied as illustrated in the STAAD report

kN
Floor Load W  1.96
2
m

2.5
Tributary width for edge member b  m 1250.00 mm
2

Uniform Live load acting on edge member: kN kN

W1  b 1.96  2.45
m
2 m
Point Load
W2  9.81kN

Load Combination:
DL + LL (Service Load State)

1.2DL + 1.6LL (Ultimate Load State)

Page 2
 KEY PLAN:

E2-202

GENERAL NOTES
1. DO NOT SCALE FROM THE DRAWING.
2. ONLY WRITTEN DIMENSIONS ARE TO BE FOLLOWED.
ANY DISCREPANCIES MUST BE ADVISED TO THE ARCHITECT OR THE ENGINEERS.
3. ALL DIMENSIONS ARE IN MILLIMETERS AND LEVELS IN METERS UNLESS
NOTED OTHERWISE.
DIMENSIONS ARE TO BE VERIFIED ON SITE AND APPROVED BY THE ENGINEERS
BEFORE COMMENCEMENT OF WORK..
3. THIS DRAWING SHOULD BE READ IN CONJUNCTION WITH OTHER RELEVANT
ARCHITECTURAL, STRUCTURAL, MECHANICAL AND ELECTRICAL DRAWINGS
AND ALL RELEVANT SECTIONS OF THE SPECIFICATIONS.

16
17
18

S1
----
19

Rev. Descriptions Date Drawn by Chk'd by

REVISION DETAILS
ITEM2 PROJECT:

CLIENT:
SRG HOLDING LIMITED
Tel. +971 4 225 1251
Fax. +971 4 226 3012
P.O. Box 11189 Dubai
E-mail. www.srg.ae

CONSULTANT:
Dubai,
-- SCAFFOLDING PARTIAL PLAN S1 SECTION - 1 tel.
fax
971 4 3575557
971 4 3575556
P.O. box 30509, Dubai U.A.E

ITEM1
SUB CONTRACTOR:

DESIGN MGR.
STRUCT ENG.
ARCHITECT

MEP
FACADE
DRAWING TITLE

SCAFFOLDING + MONORAIL
@ ELEV. 2 FOR LOUVER

Scale Date
1:75 1-04-2017
Drawn By Checked By Approved By
-- --
Drawing No. SHT. Rev.

Page 3
 STAAD REPORT
FOR ITEM1

Page 4
Job Information
Engineer Checked Approved

Name:
Date: 09-Aug-18

Structure Type SPACE FRAME

Number of Nodes 146 Highest Node 154

Number of Elements 218 Highest Beam 277

Number of Basic Load Cases 2

Number of Combination Load Cases 2

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DEAD LOAD

Primary 2 LIVE LOAD
Combination 3 (DL+LL)
Combination 4 (1.2DL+1.6LL)

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 PIP483.0 4.270 11.000 11.000 21.999 STEEL
2 PIP485.0 6.800 16.200 16.200 32.305 STEEL

Materials
Mat Name E  Density 
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6

Primary Load Cases

Number Name Type

1 DEAD LOAD None

2 LIVE LOAD None

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 (DL+LL) 1 DEAD LOAD 1.00

2 LIVE LOAD 1.00
4 (1.2DL+1.6LL) 1 DEAD LOAD 1.20
2 LIVE LOAD 1.60

Page 5
 0.500m Entity Color Legend
PIP483.0

0.300m PIP485.0
0.500m

1.000m

1.000m
0.500m
0.500m

Y
X
Z
1.800m

Structural Model

Y
X
Z Load 1

Dead Load Diagram

Page 6
 -9.810 kN

-2.450 kN/m

-2.450 kN/m

Y
X
Z Load 2

Live Load Diagram

Max:2.991
Max: 3.103mm
mm
Max: 3.116
Max: 3.096 mm
mm

Y Max: 1.327 mm
X Load 3 : Displacemen
Z Displacement - m

Deflection Diagram (DL+LL)

Page 7
 Max: 106.191
Max:-81.924
Max: N/mm2
59.302 N/mm2
Max: -70.607 N/mm2
Max:
Max:
Max: 77.032N/mm2
67.430
-67.818 N/mm2
Max: -110.820 N/mm2

Max: 240.403 N/mm2

Max: -240.506 N/mm2

Max: -17.352
Max: 48.592 N/mm2
N/mm2

Y
X Max: 2.707
-7.757N/mm2
N/mm2 Load 4 : Beam Stress
Z Stress - N/mm2

Stress Diagram (1.2DL+1.6LL)

12.098kN
12.098 kN
-7.691
-0.163 kNkN
-7.660
-0.132 kNkN
-11.488
-11.488 kNkN

-0.035 kN
-0.035 kN

6.670 kN
6.682 kN

-1.118 kN

Y
X Load 4 : Axial Force
Z Force - kN
-1.039 kN

Axial Forces Diagram (1.2DL+1.6LL)

Page 8
 Max:-1.799
Max: 1.891kN
-2.110 kN
Max: -2.324 kN

Max: -3.584 kN

Max: -0.492 kN

Y
X Load 4 : Shear Y
Z Force - kN
Max: 0.035 kN

SHear Force Diagram (1.2DL+1.6LL)

Max: 0.474 kNm

Max: 0.454
Max: -0.593kNm
kNm
Max: -0.630 kNm

Max: -1.613 kNm

Max: -0.150 kNm

Y
X Max: -0.024 kNm Load 4 : Bending Z
Z Moment - kNm

Bending moment diagram (1.2DL+1.6LL)

Page 9
 X = 0.118 kN
Y = 8.261 kN
Z = 0.000 kN
X = 0.492 kN
Y = 6.682 kN
Z = 0.000 kN X = -0.302 kN
Y
X Y = 11.719 kN
Z Z = 0.000 kN Load 4
X = -0.309 kN
Y = 11.306 kN
Z = 0.000 kN

Support Reactions

Page 10
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 PIP485.0 PIP485.0 0.018 1.000 0.018 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
2 PIP483.0 PIP483.0 0.174 1.000 0.174 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
3 PIP483.0 PIP483.0 0.172 1.000 0.172 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
4 PIP483.0 PIP483.0 0.023 1.000 0.023 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
5 PIP483.0 PIP483.0 0.052 1.000 0.052 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
6 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
7 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
8 PIP483.0 PIP483.0 0.011 1.000 0.011 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
9 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
10 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
11 PIP483.0 PIP483.0 0.102 1.000 0.102 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
12 PIP483.0 PIP483.0 0.102 1.000 0.102 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
13 PIP483.0 PIP483.0 0.145 1.000 0.145 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
14 PIP483.0 PIP483.0 0.112 1.000 0.112 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
15 PIP483.0 PIP483.0 0.094 1.000 0.094 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
16 PIP483.0 PIP483.0 0.090 1.000 0.090 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
17 PIP483.0 PIP483.0 0.107 1.000 0.107 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
18 PIP483.0 PIP483.0 0.111 1.000 0.111 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
19 PIP483.0 PIP483.0 0.131 1.000 0.131 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
20 PIP483.0 PIP483.0 0.148 1.000 0.148 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
21 PIP483.0 PIP483.0 0.105 1.000 0.105 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
22 PIP483.0 PIP483.0 0.105 1.000 0.105 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
23 PIP483.0 PIP483.0 0.099 1.000 0.099 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
24 PIP483.0 PIP483.0 0.102 1.000 0.102 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
25 PIP483.0 PIP483.0 0.133 1.000 0.133 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
26 PIP483.0 PIP483.0 0.130 1.000 0.130 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
27 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
28 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
29 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
30 PIP483.0 PIP483.0 0.077 1.000 0.077 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
31 PIP483.0 PIP483.0 0.073 1.000 0.073 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
32 PIP483.0 PIP483.0 0.114 1.000 0.114 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
33 PIP483.0 PIP483.0 0.117 1.000 0.117 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
34 PIP483.0 PIP483.0 0.085 1.000 0.085 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
35 PIP483.0 PIP483.0 0.084 1.000 0.084 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
36 PIP483.0 PIP483.0 0.142 1.000 0.142 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
37 PIP483.0 PIP483.0 0.130 1.000 0.130 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
38 PIP483.0 PIP483.0 0.072 1.000 0.072 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
39 PIP483.0 PIP483.0 0.075 1.000 0.075 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
40 PIP483.0 PIP483.0 0.126 1.000 0.126 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
41 PIP483.0 PIP483.0 0.124 1.000 0.124 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
42 PIP483.0 PIP483.0 0.069 1.000 0.069 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
43 PIP483.0 PIP483.0 0.065 1.000 0.065 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
44 PIP483.0 PIP483.0 0.138 1.000 0.138 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
45 PIP483.0 PIP483.0 0.141 1.000 0.141 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
46 PIP483.0 PIP483.0 0.057 1.000 0.057 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
47 PIP483.0 PIP483.0 0.055 1.000 0.055 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
48 PIP483.0 PIP483.0 0.131 1.000 0.131 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
49 PIP483.0 PIP483.0 0.133 1.000 0.133 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
50 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
51 PIP483.0 PIP483.0 0.054 1.000 0.054 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
52 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
53 PIP483.0 PIP483.0 0.054 1.000 0.054 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
54 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
55 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
56 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
57 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
58 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000

Page 11
Utilization Ratio Cont...
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
59 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
60 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
61 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
62 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
63 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
64 PIP483.0 PIP483.0 0.062 1.000 0.062 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
65 PIP483.0 PIP483.0 0.049 1.000 0.049 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
66 PIP483.0 PIP483.0 0.153 1.000 0.153 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
67 PIP483.0 PIP483.0 0.145 1.000 0.145 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
68 PIP483.0 PIP483.0 0.034 1.000 0.034 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
69 PIP483.0 PIP483.0 0.071 1.000 0.071 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
71 PIP483.0 PIP483.0 0.105 1.000 0.105 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
72 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
73 PIP483.0 PIP483.0 0.048 1.000 0.048 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
74 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
75 PIP485.0 PIP485.0 0.623 1.000 0.623 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
76 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
79 PIP483.0 PIP483.0 0.000 1.000 0.000 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
80 PIP483.0 PIP483.0 0.027 1.000 0.027 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
81 PIP483.0 PIP483.0 0.000 1.000 0.000 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
82 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.3.2 4 4.270 11.000 11.000 22.000
83 PIP483.0 PIP483.0 0.000 1.000 0.000 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
84 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
85 PIP485.0 PIP485.0 0.003 1.000 0.003 BS-4.8.3.2 4 6.800 16.200 16.200 32.400
86 PIP483.0 PIP483.0 0.021 1.000 0.021 BS-4.8.3.2 4 4.270 11.000 11.000 22.000
87 PIP485.0 PIP485.0 0.025 1.000 0.025 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
88 PIP485.0 PIP485.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
89 PIP485.0 PIP485.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
90 PIP485.0 PIP485.0 0.019 1.000 0.019 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
91 PIP485.0 PIP485.0 0.026 1.000 0.026 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
92 PIP485.0 PIP485.0 0.043 1.000 0.043 ANNEX I.1 4 6.800 16.200 16.200 32.400
93 PIP483.0 PIP483.0 0.247 1.000 0.247 ANNEX I.1 4 4.270 11.000 11.000 22.000
94 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
95 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
96 PIP483.0 PIP483.0 0.044 1.000 0.044 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
97 PIP485.0 PIP485.0 0.014 1.000 0.014 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
98 PIP485.0 PIP485.0 0.019 1.000 0.019 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
99 PIP485.0 PIP485.0 0.018 1.000 0.018 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
100 PIP485.0 PIP485.0 0.017 1.000 0.017 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
101 PIP485.0 PIP485.0 0.022 1.000 0.022 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
102 PIP483.0 PIP483.0 0.183 1.000 0.183 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
103 PIP485.0 PIP485.0 0.056 1.000 0.056 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
104 PIP483.0 PIP483.0 0.359 1.000 0.359 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
105 PIP485.0 PIP485.0 0.430 1.000 0.430 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
106 PIP485.0 PIP485.0 0.372 1.000 0.372 ANNEX I.1 4 6.800 16.200 16.200 32.400
107 PIP483.0 PIP483.0 0.226 1.000 0.226 ANNEX I.1 4 4.270 11.000 11.000 22.000
108 PIP483.0 PIP483.0 0.000 1.000 0.000 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
109 PIP485.0 PIP485.0 0.003 1.000 0.003 BS-4.8.3.2 2 6.800 16.200 16.200 32.400
110 PIP485.0 PIP485.0 0.023 1.000 0.023 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
111 PIP485.0 PIP485.0 0.027 1.000 0.027 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
112 PIP485.0 PIP485.0 0.025 1.000 0.025 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
113 PIP485.0 PIP485.0 0.022 1.000 0.022 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
114 PIP485.0 PIP485.0 0.024 1.000 0.024 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
115 PIP485.0 PIP485.0 0.046 1.000 0.046 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
117 PIP483.0 PIP483.0 0.344 1.000 0.344 BS-4.8.3.2 4 4.270 11.000 11.000 22.000
118 PIP485.0 PIP485.0 0.273 1.000 0.273 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
119 PIP485.0 PIP485.0 0.414 1.000 0.414 ANNEX I.1 4 6.800 16.200 16.200 32.400
120 PIP485.0 PIP485.0 0.242 1.000 0.242 BS-4.8.3.3.1 3 6.800 16.200 16.200 32.400

Page 12
Utilization Ratio Cont...
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
121 PIP485.0 PIP485.0 0.277 1.000 0.277 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
122 PIP485.0 PIP485.0 0.144 1.000 0.144 BS-4.8.3.3.1 2 6.800 16.200 16.200 32.400
123 PIP485.0 PIP485.0 0.477 1.000 0.477 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
124 PIP485.0 PIP485.0 0.305 1.000 0.305 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
125 PIP485.0 PIP485.0 0.202 1.000 0.202 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
126 PIP485.0 PIP485.0 0.178 1.000 0.178 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
127 PIP485.0 PIP485.0 0.483 1.000 0.483 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
128 PIP485.0 PIP485.0 0.224 1.000 0.224 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
129 PIP485.0 PIP485.0 0.176 1.000 0.176 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
130 PIP485.0 PIP485.0 0.245 1.000 0.245 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
131 PIP485.0 PIP485.0 0.260 1.000 0.260 ANNEX I.1 4 6.800 16.200 16.200 32.400
132 PIP485.0 PIP485.0 0.163 1.000 0.163 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
133 PIP485.0 PIP485.0 0.146 1.000 0.146 ANNEX I.1 4 6.800 16.200 16.200 32.400
134 PIP485.0 PIP485.0 0.162 1.000 0.162 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
136 PIP485.0 PIP485.0 0.160 1.000 0.160 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
137 PIP485.0 PIP485.0 0.147 1.000 0.147 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
138 PIP485.0 PIP485.0 0.201 1.000 0.201 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
140 PIP485.0 PIP485.0 0.262 1.000 0.262 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
141 PIP485.0 PIP485.0 0.241 1.000 0.241 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
143 PIP485.0 PIP485.0 0.007 1.000 0.007 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
152 PIP485.0 PIP485.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
153 PIP485.0 PIP485.0 0.022 1.000 0.022 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
154 PIP485.0 PIP485.0 0.019 1.000 0.019 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
155 PIP485.0 PIP485.0 0.017 1.000 0.017 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
157 PIP485.0 PIP485.0 0.006 1.000 0.006 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
161 PIP485.0 PIP485.0 0.008 1.000 0.008 BS-4.8.3.3.1 2 6.800 16.200 16.200 32.400
164 PIP485.0 PIP485.0 0.017 1.000 0.017 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
165 PIP485.0 PIP485.0 0.008 1.000 0.008 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
168 PIP483.0 PIP483.0 0.086 1.000 0.086 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
169 PIP483.0 PIP483.0 0.071 1.000 0.071 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
170 PIP483.0 PIP483.0 0.064 1.000 0.064 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
171 PIP483.0 PIP483.0 0.074 1.000 0.074 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
172 PIP483.0 PIP483.0 0.056 1.000 0.056 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
173 PIP483.0 PIP483.0 0.060 1.000 0.060 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
174 PIP483.0 PIP483.0 0.083 1.000 0.083 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
175 PIP483.0 PIP483.0 0.082 1.000 0.082 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
176 PIP483.0 PIP483.0 0.043 1.000 0.043 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
177 PIP483.0 PIP483.0 0.063 1.000 0.063 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
178 PIP483.0 PIP483.0 0.073 1.000 0.073 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
179 PIP483.0 PIP483.0 0.072 1.000 0.072 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
180 PIP483.0 PIP483.0 0.043 1.000 0.043 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
181 PIP483.0 PIP483.0 0.042 1.000 0.042 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
184 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
185 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
186 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
187 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
188 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
189 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
190 PIP483.0 PIP483.0 0.011 1.000 0.011 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
191 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
192 PIP483.0 PIP483.0 0.073 1.000 0.073 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
193 PIP483.0 PIP483.0 0.101 1.000 0.101 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
194 PIP483.0 PIP483.0 0.058 1.000 0.058 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
195 PIP483.0 PIP483.0 0.041 1.000 0.041 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
196 PIP483.0 PIP483.0 0.049 1.000 0.049 BS-4.8.3.3.1 3 4.270 11.000 11.000 22.000
197 PIP483.0 PIP483.0 0.193 1.000 0.193 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
198 PIP483.0 PIP483.0 0.021 1.000 0.021 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
200 PIP485.0 PIP485.0 0.019 1.000 0.019 BS-4.8.2.2 4 6.800 16.200 16.200 32.400

Page 13
Utilization Ratio Cont...
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
202 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
203 PIP485.0 PIP485.0 0.623 1.000 0.623 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
204 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
205 PIP483.0 PIP483.0 0.000 1.000 0.000 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
232 PIP483.0 PIP483.0 0.037 1.000 0.037 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
235 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.7 (C) 4 6.800 16.200 16.200 32.400
236 PIP485.0 PIP485.0 0.065 1.000 0.065 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
237 PIP485.0 PIP485.0 0.024 1.000 0.024 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
238 PIP485.0 PIP485.0 0.018 1.000 0.018 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
239 PIP485.0 PIP485.0 0.014 1.000 0.014 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
240 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
241 PIP485.0 PIP485.0 0.012 1.000 0.012 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
242 PIP485.0 PIP485.0 0.008 1.000 0.008 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
243 PIP485.0 PIP485.0 0.013 1.000 0.013 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
244 PIP485.0 PIP485.0 0.015 1.000 0.015 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
245 PIP485.0 PIP485.0 0.018 1.000 0.018 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
246 PIP485.0 PIP485.0 0.036 1.000 0.036 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
247 PIP485.0 PIP485.0 0.035 1.000 0.035 ANNEX I.1 4 6.800 16.200 16.200 32.400
248 PIP483.0 PIP483.0 0.000 1.000 0.000 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
249 PIP485.0 PIP485.0 0.103 1.000 0.103 ANNEX I.1 4 6.800 16.200 16.200 32.400
250 PIP483.0 PIP483.0 0.087 1.000 0.087 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
251 PIP483.0 PIP483.0 0.080 1.000 0.080 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
252 PIP483.0 PIP483.0 0.065 1.000 0.065 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
253 PIP483.0 PIP483.0 0.100 1.000 0.100 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
254 PIP483.0 PIP483.0 0.071 1.000 0.071 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
255 PIP483.0 PIP483.0 0.072 1.000 0.072 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
256 PIP483.0 PIP483.0 0.011 1.000 0.011 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
257 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
262 PIP485.0 PIP485.0 0.001 1.000 0.001 BS-4.8.3.2 4 6.800 16.200 16.200 32.400
263 PIP485.0 PIP485.0 0.001 1.000 0.001 BS-4.8.3.2 4 6.800 16.200 16.200 32.400
264 PIP483.0 PIP483.0 0.084 1.000 0.084 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
265 PIP483.0 PIP483.0 0.042 1.000 0.042 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
266 PIP483.0 PIP483.0 0.056 1.000 0.056 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
267 PIP483.0 PIP483.0 0.094 1.000 0.094 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
268 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
269 PIP483.0 PIP483.0 0.048 1.000 0.048 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
270 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
271 PIP483.0 PIP483.0 0.047 1.000 0.047 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
272 PIP485.0 PIP485.0 0.017 1.000 0.017 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
273 PIP483.0 PIP483.0 0.073 1.000 0.073 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
274 PIP483.0 PIP483.0 0.099 1.000 0.099 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
275 PIP483.0 PIP483.0 0.091 1.000 0.091 ANNEX I.1 4 4.270 11.000 11.000 22.000
276 PIP483.0 PIP483.0 0.114 1.000 0.114 BS-4.8.3.3.1 3 4.270 11.000 11.000 22.000
277 PIP483.0 PIP483.0 0.023 1.000 0.023 BS-4.8.2.2 4 4.270 11.000 11.000 22.000

Page 14
Steel Design (Track 2) Beam 75 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

75 ST PIP485.0 PASS BS-4.8.2.2 0.623 4

0.05 T 0.00 1.61 0.90
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 180.00
Gross Area = 6.80 Net Area = 6.80 Eff. Area = 6.80

z-z axis y-y axis

Moment of inertia : 16.200 16.200
Plastic modulus : 9.420 9.420
Elastic modulus : 6.708 6.708
Effective modulus : 6.708 6.708
Shear Area : 4.080 4.080

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : PLASTIC
Squash Load : 187.00
Axial force/Squash load : 0.000

z-z axis y-y axis

Compression Capacity : 84.6 84.6
Tension Capacity : 187.0 187.0
Moment Capacity : 2.6 2.6
Reduced Moment Capacity : 2.6 2.6
Shear Capacity : 67.3 67.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)
x-x axis y-y axis
Slenderness : 116.619 116.619
Radius of gyration (cm) : 1.543 1.543
Effective Length : 1.800 1.800

LTB check unnecessary for this section

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.053 4 - 3.6 - - -
BS-4.8.2.2 0.623 4 0.1 0.0 0.0 1.6 0.0
BS-4.8.2.3 0.623 4 0.1 - - 1.6 0.0
BS-4.8.3.2 0.008 1 0.0 0.0 0.0 0.0 0.0
BS-4.8.3.3.1 0.011 1 0.0 - - 0.0 0.0
BS-4.8.3.3.3 0.011 1 0.0 - - 0.0 0.0
ANNEX I.1 0.008 1 0.0 - - 0.0 0.0
Torsion and deflections have not been considered in the design.

Page 15
Steel Design (Track 2) Beam 104 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

104 ST PIP483.0 PASS BS-4.8.2.2 0.359 4

3.85 T 0.00 0.55 0.02
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 1.50
Gross Area = 4.27 Net Area = 4.27 Eff. Area = 4.27

z-z axis y-y axis

Moment of inertia : 11.000 11.000
Plastic modulus : 6.170 6.170
Elastic modulus : 4.555 4.555
Effective modulus : 6.170 6.170
Shear Area : 2.562 2.562

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : PLASTIC

z-z axis y-y axis

Tension Capacity : 117.4 117.4
Moment Capacity : 1.7 1.7
Reduced Moment Capacity : 1.7 1.7
Shear Capacity : 42.3 42.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)

LTB check unnecessary for this section

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.059 4 - 2.5 - - -
BS-4.6 (T) 0.033 4 3.9 - - - -
BS-4.8.2.2 0.359 4 3.9 2.5 0.0 0.6 0.0
BS-4.8.2.3 0.326 4 3.9 - - 0.6 0.0
Torsion and deflections have not been considered in the design.

Page 16
Structural Check for ITEM1

Deflection Check:
δMax  3.1mm
Max Deflection:
2385mm
Deflection limit: δcap   11.93 mm
200
δMax  δcap "Therefore OK"

Stress Check:
Maximum Stress σ Max  240MPa

Steel Grade 275 Tensile Strength py  275MPa

Stress Capacity σ Cap  py  275.00 MPa

σ Max  σ Cap "Therefore OK"

Page 17
 STAAD REPORT
FOR ITEM2

Page 18
Job Information
Engineer Checked Approved

Name:
Date: 11-Aug-18

Structure Type SPACE FRAME

Number of Nodes 85 Highest Node 85

Number of Elements 127 Highest Beam 127

Number of Basic Load Cases 2

Number of Combination Load Cases 2

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DL
Primary 2 LL
Combination 3 DL+LL
Combination 4 1.2DL+1.6LL

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 PIP483.0 4.270 11.000 11.000 21.999 STEEL
2 PIP485.0 6.800 16.200 16.200 32.305 STEEL

Materials
Mat Name E  Density 
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6

Primary Load Cases

Number Name Type

1 DL None
2 LL None

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 DL+LL 1 DL 1.00
2 LL 1.00
4 1.2DL+1.6LL 1 DL 1.20
2 LL 1.60

Page 19
 Entity Color Legend
3.624m
PIP483.0
PIP485.0
1.800m Default Plate Color
Default Solid Color

2.691m
17.000m

Y
X
Z Load 2

Structural Model

Y
X
Z Load 1

Dead Load Diagram

Page 20
 -9.810 kN

-2.450 kN/m

Y
X
Z Load 2

Live Loads Diagram

Max: 14.942 mm
Max: 17.451 mm

Y
X Load 3 : Displacement
Z Displacement - mm

Deflection Diagram (DL+LL)

Page 21
 Max: 265.468 N/mm2
Max: Max:
0.090 -224.569
-0.090 N/mm2 N/mm2
N/mm2

5.272 N/mm2
Max: -5.191 N/mm2

Max: 65.437 N/mm2

Y
X Load 4 : Beam Stres
Z Stress - N/m

Stress Diagram (1.2DL+1.6LL)

Page 22
 Max: 1.644 kNm
Max: 0.001 kNm
Max: -1.613 kNm

Max: -0.024 kNm

Max: 0.015 kNm

Y
X Load 4 : Bending
Z Moment - k

Bending moment diagram

Page 23
 Max: 8.406 kN
Max: 0.009 kNMax: -3.584 kN

Max: 0.035 kN

Max: 0.011 kN

Y
X Load 4 : Shear
Z Force -

Shear Diagram (1.2DL+1.6LL)

Page 24
 13.906kN
13.906 kN
00kN
kN -0.129 kN
-0.129 kN

-0.022 kN

0.057 kN

26.571 kN

26.610 kN

Y
X Load 4 : Axial Forc
Z Force -

Axial Forces Diagram (1.2DL+1.6LL)

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
2 PIP483.0 PIP483.0 0.016 1.000 0.016 BS-4.7 (C) 1 4.270 11.000 11.000 22.000
3 PIP483.0 PIP483.0 0.234 1.000 0.234 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
4 PIP483.0 PIP483.0 0.021 1.000 0.021 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
5 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
6 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
7 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
8 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
9 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
10 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
11 PIP483.0 PIP483.0 0.016 1.000 0.016 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
12 PIP483.0 PIP483.0 0.016 1.000 0.016 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
13 PIP483.0 PIP483.0 0.018 1.000 0.018 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
14 PIP483.0 PIP483.0 0.016 1.000 0.016 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
15 PIP483.0 PIP483.0 0.014 1.000 0.014 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
16 PIP483.0 PIP483.0 0.014 1.000 0.014 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
17 PIP483.0 PIP483.0 0.241 1.000 0.241 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
18 PIP483.0 PIP483.0 0.239 1.000 0.239 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
19 PIP483.0 PIP483.0 0.278 1.000 0.278 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
20 PIP483.0 PIP483.0 0.279 1.000 0.279 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
21 PIP483.0 PIP483.0 0.244 1.000 0.244 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
22 PIP483.0 PIP483.0 0.242 1.000 0.242 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000

Page 25
Utilization Ratio Cont...
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
23 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.3.3.1 1 4.270 11.000 11.000 22.000
24 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.2.2 2 4.270 11.000 11.000 22.000
25 PIP483.0 PIP483.0 0.276 1.000 0.276 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
26 PIP483.0 PIP483.0 0.270 1.000 0.270 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
27 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
28 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
29 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
30 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.2.2 2 4.270 11.000 11.000 22.000
31 PIP483.0 PIP483.0 0.014 1.000 0.014 BS-4.8.2.2 2 4.270 11.000 11.000 22.000
32 PIP483.0 PIP483.0 0.240 1.000 0.240 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
33 PIP483.0 PIP483.0 0.245 1.000 0.245 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
34 PIP483.0 PIP483.0 0.012 1.000 0.012 BS-4.8.2.2 2 4.270 11.000 11.000 22.000
35 PIP483.0 PIP483.0 0.012 1.000 0.012 BS-4.8.2.2 2 4.270 11.000 11.000 22.000
36 PIP483.0 PIP483.0 0.265 1.000 0.265 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
37 PIP483.0 PIP483.0 0.267 1.000 0.267 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
38 PIP483.0 PIP483.0 0.013 1.000 0.013 BS-4.8.2.2 2 4.270 11.000 11.000 22.000
39 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
40 PIP483.0 PIP483.0 0.239 1.000 0.239 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
41 PIP483.0 PIP483.0 0.236 1.000 0.236 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
42 PIP483.0 PIP483.0 0.016 1.000 0.016 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
43 PIP483.0 PIP483.0 0.014 1.000 0.014 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
44 PIP483.0 PIP483.0 0.263 1.000 0.263 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
45 PIP483.0 PIP483.0 0.268 1.000 0.268 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
46 PIP483.0 PIP483.0 0.012 1.000 0.012 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
47 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
48 PIP483.0 PIP483.0 0.231 1.000 0.231 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
49 PIP483.0 PIP483.0 0.229 1.000 0.229 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
50 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
51 PIP483.0 PIP483.0 0.022 1.000 0.022 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
52 PIP483.0 PIP483.0 0.021 1.000 0.021 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
53 PIP483.0 PIP483.0 0.021 1.000 0.021 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
54 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
55 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
56 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
57 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
58 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
59 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
60 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
61 PIP485.0 PIP485.0 0.010 1.000 0.010 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
62 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
63 PIP483.0 PIP483.0 0.009 1.000 0.009 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
64 PIP483.0 PIP483.0 0.019 1.000 0.019 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
65 PIP483.0 PIP483.0 0.033 1.000 0.033 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
66 PIP483.0 PIP483.0 0.295 1.000 0.295 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
67 PIP483.0 PIP483.0 0.268 1.000 0.268 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
68 PIP483.0 PIP483.0 0.115 1.000 0.115 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
69 PIP483.0 PIP483.0 0.116 1.000 0.116 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
70 PIP483.0 PIP483.0 0.193 1.000 0.193 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
71 PIP483.0 PIP483.0 0.020 1.000 0.020 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
72 PIP483.0 PIP483.0 0.015 1.000 0.015 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
73 PIP483.0 PIP483.0 0.011 1.000 0.011 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
74 PIP485.0 PIP485.0 0.623 1.000 0.623 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
75 PIP483.0 PIP483.0 0.024 1.000 0.024 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
76 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.7 (C) 4 6.800 16.200 16.200 32.400
77 PIP485.0 PIP485.0 0.105 1.000 0.105 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
78 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.7 (C) 4 6.800 16.200 16.200 32.400
79 PIP485.0 PIP485.0 0.098 1.000 0.098 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
80 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.7 (C) 4 6.800 16.200 16.200 32.400

Page 26
Utilization Ratio Cont...
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
81 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
82 PIP485.0 PIP485.0 0.019 1.000 0.019 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
83 PIP483.0 PIP483.0 0.151 1.000 0.151 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
84 PIP485.0 PIP485.0 0.195 1.000 0.195 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
85 PIP485.0 PIP485.0 0.193 1.000 0.193 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
86 PIP485.0 PIP485.0 0.199 1.000 0.199 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
87 PIP485.0 PIP485.0 0.225 1.000 0.225 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
88 PIP485.0 PIP485.0 0.256 1.000 0.256 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
89 PIP485.0 PIP485.0 0.383 1.000 0.383 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
90 PIP485.0 PIP485.0 0.180 1.000 0.180 ANNEX I.1 4 6.800 16.200 16.200 32.400
91 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
92 PIP485.0 PIP485.0 0.018 1.000 0.018 ANNEX I.1 4 6.800 16.200 16.200 32.400
93 PIP485.0 PIP485.0 0.086 1.000 0.086 ANNEX I.1 4 6.800 16.200 16.200 32.400
94 PIP485.0 PIP485.0 0.300 1.000 0.300 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
95 PIP485.0 PIP485.0 0.163 1.000 0.163 ANNEX I.1 4 6.800 16.200 16.200 32.400
96 PIP485.0 PIP485.0 0.261 1.000 0.261 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
97 PIP485.0 PIP485.0 0.181 1.000 0.181 BS-4.8.3.3.1 3 6.800 16.200 16.200 32.400
98 PIP485.0 PIP485.0 0.261 1.000 0.261 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
99 PIP483.0 PIP483.0 0.192 1.000 0.192 BS-4.7 (C) 4 4.270 11.000 11.000 22.000
100 PIP485.0 PIP485.0 0.270 1.000 0.270 BS-4.8.3.3.1 3 6.800 16.200 16.200 32.400
101 PIP483.0 PIP483.0 0.564 1.000 0.564 ANNEX I.1 4 4.270 11.000 11.000 22.000
102 PIP485.0 PIP485.0 0.640 1.000 0.640 ANNEX I.1 4 6.800 16.200 16.200 32.400
103 PIP485.0 PIP485.0 0.646 1.000 0.646 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
104 PIP485.0 PIP485.0 0.163 1.000 0.163 ANNEX I.1 4 6.800 16.200 16.200 32.400
105 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.7 (C) 4 6.800 16.200 16.200 32.400
106 PIP485.0 PIP485.0 0.019 1.000 0.019 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
107 PIP485.0 PIP485.0 0.080 1.000 0.080 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
108 PIP485.0 PIP485.0 0.262 1.000 0.262 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
109 PIP485.0 PIP485.0 0.303 1.000 0.303 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
110 PIP485.0 PIP485.0 0.311 1.000 0.311 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
111 PIP485.0 PIP485.0 0.304 1.000 0.304 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
112 PIP485.0 PIP485.0 0.246 1.000 0.246 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
113 PIP485.0 PIP485.0 0.482 1.000 0.482 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
114 PIP485.0 PIP485.0 0.106 1.000 0.106 BS-4.8.3.3.1 2 6.800 16.200 16.200 32.400
115 PIP485.0 PIP485.0 0.579 1.000 0.579 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
116 PIP485.0 PIP485.0 0.167 1.000 0.167 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
117 PIP485.0 PIP485.0 0.043 1.000 0.043 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
118 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.8.3.2 4 6.800 16.200 16.200 32.400
119 PIP485.0 PIP485.0 0.472 1.000 0.472 ANNEX I.1 4 6.800 16.200 16.200 32.400
120 PIP485.0 PIP485.0 0.281 1.000 0.281 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
121 PIP485.0 PIP485.0 0.041 1.000 0.041 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
122 PIP485.0 PIP485.0 0.000 1.000 0.000 BS-4.8.3.2 4 6.800 16.200 16.200 32.400
123 PIP485.0 PIP485.0 0.694 1.000 0.694 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
124 PIP485.0 PIP485.0 0.572 1.000 0.572 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
125 PIP485.0 PIP485.0 0.124 1.000 0.124 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
126 PIP485.0 PIP485.0 0.030 1.000 0.030 BS-4.8.3.3.1 4 6.800 16.200 16.200 32.400
127 PIP485.0 PIP485.0 0.195 1.000 0.195 BS-4.8.3.2 4 6.800 16.200 16.200 32.400

Page 27
Steel Design (Track 2) Beam 101 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

101 ST PIP483.0 PASS ANNEX I.1 0.564 4

15.22 C 0.00 0.94 -
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 1.50
Gross Area = 4.27 Net Area = 4.27 Eff. Area = 4.27

z-z axis y-y axis

Moment of inertia : 11.000 11.000
Plastic modulus : 6.170 6.170
Elastic modulus : 4.555 4.555
Effective modulus : 6.170 6.170
Shear Area : 2.562 2.562

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : PLASTIC
Squash Load : 117.43
Axial force/Squash load : 0.130

z-z axis y-y axis

Compression Capacity : 117.4 117.4
Moment Capacity : 1.7 1.7
Reduced Moment Capacity : 1.7 1.7
Shear Capacity : 42.3 42.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)
x-x axis y-y axis
Slenderness : 0.935 0.935
Radius of gyration (cm) : 1.605 1.605
Effective Length : 0.015 0.015

LTB check unnecessary for this section

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.151 4 - 6.4 - - -
BS-4.7 (C) 0.130 4 15.2 - - - -
BS-4.8.3.2 0.564 4 15.2 6.4 0.0 0.9 0.0
BS-4.8.3.3.1 0.682 4 15.2 - - 0.9 0.0
BS-4.8.3.3.3 0.718 4 15.2 - - 0.9 0.0
ANNEX I.1 0.564 4 15.2 - - 0.9 0.0
Torsion and deflections have not been considered in the design.

Page 28
Steel Design (Track 2) Beam 123 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

123 ST PIP485.0 PASS BS-4.8.3.3.1 0.694 4

0.83 C 0.00 1.78 -
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 50.00
Gross Area = 6.80 Net Area = 6.80 Eff. Area = 6.80

z-z axis y-y axis

Moment of inertia : 16.200 16.200
Plastic modulus : 9.420 9.420
Elastic modulus : 6.708 6.708
Effective modulus : 9.420 9.420
Shear Area : 4.080 4.080

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : SEMI-COMPACT
Squash Load : 187.00
Axial force/Squash load : 0.005

z-z axis y-y axis

Compression Capacity : 180.6 180.6
Tension Capacity : 187.0 187.0
Moment Capacity : 1.8 1.8
Reduced Moment Capacity : 1.8 1.8
Shear Capacity : 67.3 67.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)
x-x axis y-y axis
Slenderness : 32.394 32.394
Radius of gyration (cm) : 1.543 1.543
Effective Length : 0.500 0.500

LTB check unnecessary for this section

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.106 4 - 7.1 - - -
BS-4.7 (C) 0.005 4 0.9 - - - -
BS-4.8.2.2 0.008 1 0.0 0.1 0.0 0.0 0.0
BS-4.8.2.3 0.008 1 0.0 - - 0.0 0.0
BS-4.8.3.2 0.689 4 0.9 7.1 0.0 1.8 0.0
BS-4.8.3.3.1 0.694 4 0.8 - - 1.8 0.0
BS-4.8.3.3.3 0.974 4 0.8 - - 1.8 0.0
ANNEX I.1 0.690 4 0.9 - - 1.8 0.0
Torsion and deflections have not been considered in the design.

Page 29
Structural Check for ITEM2

Deflection Check:

Max Deflection of Cantilever: δMax  17.45 mm  14.94mm  2.51 mm

1330
Deflection limit: δcap  mm  7.39 mm
180
δMax  δcap "Therefore OK"

Stress Check:
Maximum Stress σ Max  265.4 MPa

Steel Grade 275 Tensile Strength py  275MPa

Stress Capacity σ Cap  py  275.00 MPa

σ Max  σ Cap "Therefore OK"

Page 30
 STAAD REPORT
FOR PLAN VIEW

Page 31
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 PIP485.0 6.800 16.200 16.200 32.305 STEEL
2 PIP483.0 4.270 11.000 11.000 21.999 STEEL

Materials
Mat Name E  Density 
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6

Primary Load Cases

Number Name Type

1 DL None
2 LL None

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 DL+LL 1 DL 1.00
2 LL 1.00
4 1.2DL+1.6LL 1 DL 1.20
2 LL 1.60

Entity Color Legend

PIP485.0
PIP483.0
Default Plate Color
Default Solid Color

2.500m

2.500m
3.202m
1.800m

Y
X
Z
Load 2

Structural Diagram

Page 32
 Y
X
Z
Load 1

Dead Load Diagram

kN/m
-1.764 kN/m(GY) -1.764 kN/m
kN/m(GY)
-1.764 kN/m
-1.764 kN/m(GY)
kN/m

-1.764 kN/m
kN/m(GY)
-1.764 kN/m(GY)
-1.764 kN/m(GY) kN/m
-1.764 kN/m(GY)

Y
X
Z
Load 2

Live Load Diagram

Page 33
 Max: 0.276 mm Max: 0.909 mm

Max: 2.301 mm

Max: 3.948 mm
Max: 3.966 mm
Max: 2.300 mm
Max: 2.034 mm Max: 0.909 mm Max: 0.276 mm Max: 2.300 mm
Max: 2.055 mm Max: 5.911 mm

Max: 3.946 mm
Max: 3.946 mm
Max: 2.301 mm
Max: 5.911 mm
Max:
Max:2.034
2.055mm
mm

Max: 3.948 mm
Max: 3.966 mm

Y
X Load 3 : Displacement
Z
Displacement - mm

Deflection Diagram (DL+LL)

Max: 60.462 N/mm2

Max: -60.462 N/mm2
Max: 23.796 N/mm2
Max: -22.123 N/mm2

Max: 56.449 N/mm2 Max: 116.466 N/mm2

Max: -113.346 N/mm2
Max: -61.145 N/mm2

Max: 112.248 N/mm2

Max: -109.127 N/mm2

Y
X Load 4 : Beam Stress
Z
Stress - N/mm2

Stress Diagram (1.2DL+1.6LL)

Page 34
 Max: 0.275 kNm

Max: -0.154 kNm

Max: -0.394 kNm

Max: -0.201 kNm

Max: -0.394 kNm
Max: -0.299 kNm
Max: -0.395 kNm
Max: -0.190 kNm

Y
X Load 4 : Bending Z
Z
Moment - kNm

Bending moment diagram (1.2DL+1.6LL)

Max: -0.257 kN

Max: 0.875 kN

Max: -1.498 kN

Max: -0.243 kN
Max: 1.499 kN
Max: -1.498 kN

Max: -0.190 kN
Max: -0.257 kN

Y
X Load 4 : Shear Y
Z
Force - kN

Shear Diagram (1.2DL+1.6LL)

Page 35
 0 kN

0 kN
1.369 kN
0.569 kN

0.569 kN
1.369 kN

-1.597 kN
0.666 kN
2.193
1.369kN
kN
-1.597 kN

1.369kN
0.666 kN
2.233 kN

0.706 kN

Y
X 0.706 kN Load 4 : Axial Force
Z
Force - kN

Axial Forces Diagram (1.2DL+1.6LL)

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 PIP485.0 PIP485.0 0.063 1.000 0.063 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
4 PIP485.0 PIP485.0 0.060 1.000 0.060 ANNEX I.1 4 6.800 16.200 16.200 32.400
5 PIP485.0 PIP485.0 0.161 1.000 0.161 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
8 PIP485.0 PIP485.0 0.154 1.000 0.154 ANNEX I.1 4 6.800 16.200 16.200 32.400
50 PIP485.0 PIP485.0 0.155 1.000 0.155 ANNEX I.1 4 6.800 16.200 16.200 32.400
54 PIP485.0 PIP485.0 0.161 1.000 0.161 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
72 PIP483.0 PIP483.0 0.244 1.000 0.244 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
73 PIP483.0 PIP483.0 0.511 1.000 0.511 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
74 PIP483.0 PIP483.0 0.188 1.000 0.188 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
75 PIP483.0 PIP483.0 0.390 1.000 0.390 ANNEX I.1 4 4.270 11.000 11.000 22.000
76 PIP483.0 PIP483.0 0.188 1.000 0.188 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
77 PIP483.0 PIP483.0 0.390 1.000 0.390 ANNEX I.1 4 4.270 11.000 11.000 22.000
78 PIP483.0 PIP483.0 0.244 1.000 0.244 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
79 PIP483.0 PIP483.0 0.511 1.000 0.511 BS-4.8.3.3.1 4 4.270 11.000 11.000 22.000
82 PIP485.0 PIP485.0 0.060 1.000 0.060 ANNEX I.1 4 6.800 16.200 16.200 32.400
83 PIP485.0 PIP485.0 0.063 1.000 0.063 BS-4.8.2.2 4 6.800 16.200 16.200 32.400
84 PIP483.0 PIP483.0 0.194 1.000 0.194 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
85 PIP483.0 PIP483.0 0.260 1.000 0.260 BS-4.8.3.3.3 4 4.270 11.000 11.000 22.000
86 PIP483.0 PIP483.0 0.131 1.000 0.131 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
87 PIP483.0 PIP483.0 0.208 1.000 0.208 ANNEX I.1 4 4.270 11.000 11.000 22.000
88 PIP483.0 PIP483.0 0.259 1.000 0.259 BS-4.8.3.3.3 4 4.270 11.000 11.000 22.000
89 PIP483.0 PIP483.0 0.195 1.000 0.195 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
90 PIP483.0 PIP483.0 0.131 1.000 0.131 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
91 PIP483.0 PIP483.0 0.208 1.000 0.208 ANNEX I.1 4 4.270 11.000 11.000 22.000
92 PIP483.0 PIP483.0 0.100 1.000 0.100 BS-4.8.3.3.3 4 4.270 11.000 11.000 22.000
93 PIP483.0 PIP483.0 0.174 1.000 0.174 BS-4.8.3.3.3 4 4.270 11.000 11.000 22.000
94 PIP483.0 PIP483.0 0.100 1.000 0.100 BS-4.8.3.3.3 4 4.270 11.000 11.000 22.000
95 PIP483.0 PIP483.0 0.174 1.000 0.174 BS-4.8.3.3.3 4 4.270 11.000 11.000 22.000
96 PIP483.0 PIP483.0 0.343 1.000 0.343 BS-4.8.2.2 4 4.270 11.000 11.000 22.000

Page 36
Utilization Ratio Cont...
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
97 PIP483.0 PIP483.0 0.306 1.000 0.306 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
98 PIP483.0 PIP483.0 0.306 1.000 0.306 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
99 PIP483.0 PIP483.0 0.343 1.000 0.343 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
100 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
101 PIP483.0 PIP483.0 0.018 1.000 0.018 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
102 PIP483.0 PIP483.0 0.010 1.000 0.010 BS-4.8.2.2 4 4.270 11.000 11.000 22.000
103 PIP483.0 PIP483.0 0.018 1.000 0.018 BS-4.8.2.2 4 4.270 11.000 11.000 22.000

Page 37
Steel Design (Track 2) Beam 54 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

54 ST PIP485.0 PASS BS-4.8.2.2 0.161 4

1.60 T 0.00 0.40 0.73
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 125.05
Gross Area = 6.80 Net Area = 6.80 Eff. Area = 6.80

z-z axis y-y axis

Moment of inertia : 16.200 16.200
Plastic modulus : 9.420 9.420
Elastic modulus : 6.708 6.708
Effective modulus : 6.708 6.708
Shear Area : 4.080 4.080

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : PLASTIC

z-z axis y-y axis

Tension Capacity : 187.0 187.0
Moment Capacity : 2.6 2.6
Reduced Moment Capacity : 2.6 2.6
Shear Capacity : 67.3 67.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)

LTB check unnecessary for this section

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.022 4 - 1.5 - - -
BS-4.6 (T) 0.009 4 1.6 - - - -
BS-4.8.2.2 0.161 4 1.6 0.1 0.0 0.4 0.0
BS-4.8.2.3 0.153 4 1.6 - - 0.4 0.0
Torsion and deflections have not been considered in the design.

Page 38
Steel Design (Track 2) Beam 73 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

73 ST PIP483.0 PASS BS-4.8.3.3.1 0.511 4

0.67 C 0.48 0.20 -
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 100.00
Gross Area = 4.27 Net Area = 4.27 Eff. Area = 4.27

z-z axis y-y axis

Moment of inertia : 11.000 11.000
Plastic modulus : 6.170 6.170
Elastic modulus : 4.555 4.555
Effective modulus : 6.170 6.170
Shear Area : 2.562 2.562

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : SEMI-COMPACT
Squash Load : 117.43
Axial force/Squash load : 0.006

z-z axis y-y axis

Compression Capacity : 100.8 100.8
Moment Capacity : 1.3 1.3
Reduced Moment Capacity : 1.3 1.3
Shear Capacity : 42.3 42.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)
x-x axis y-y axis
Slenderness : 62.304 62.304
Radius of gyration (cm) : 1.605 1.605
Effective Length : 1.000 1.000

LTB check unnecessary for this section

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.006 4 - 0.2 - - -
BS-4.2.3-(Z) 0.014 4 - - 0.6 - -
BS-4.7 (C) 0.007 4 0.7 - - - -
BS-4.8.3.2 0.308 4 0.7 0.2 0.6 0.5 0.0
BS-4.8.3.3.1 0.511 4 0.7 - - 0.2 0.5
BS-4.8.3.3.3 0.552 4 0.7 - - 0.2 0.5
ANNEX I.1 0.406 4 0.7 - - 0.2 0.5
Torsion and deflections have not been considered in the design.

Page 39
Structural Check

Deflection Check:

Max Deflection for bracing δMax  5.911 mm

3200
Deflection limit: δcap  mm  16.00 mm
200
δMax  δcap "Therefore OK"

Max Deflection for the 1.8m side beam δMax  2mm

1800
Deflection limit: δcap  mm  9.00 mm
200
δMax  δcap "Therefore OK"

Stress Check:
Maximum Stress σ Max  116.5 MPa

Steel Grade 275 Tensile Strength py  275MPa

Stress Capacity σ Cap  py  275.00 MPa

σ Max  σ Cap "Therefore OK"

Page 40
 IPEA200 BEAM
STAAD REPORT

Page 41
Job Information
Engineer Checked Approved

Name:
Date: 11-Aug-18

Structure Type SPACE FRAME

Number of Nodes 3 Highest Node 3

Number of Elements 2 Highest Beam 2

Number of Basic Load Cases 2

Number of Combination Load Cases 2

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DL
Primary 2 LL
Combination 3 DL+LL
Combination 4 1.2DL+1.6LL

Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 IPEA200 23.500 117.000 1.59E+3 2.864 STEEL

Materials
Mat Name E  Density 
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 CONCRETE 21.718 0.170 2.4E+3 10E -6

Primary Load Cases

Number Name Type

1 DL None
2 LL None

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 DL+LL 1 DL 1.00
2 LL 1.00
4 1.2DL+1.6LL 1 DL 1.20
2 LL 1.60

Page 42
 Entity Color Legend
IPEA200
Default Plate Color
Default Solid Color

2.500m

Y
X
Z Load 1

Structural Model

2.500m

Y
X
Z Load 1

DL Diagram

Page 43
 -9.810 kN

2.500m

Y
X
Z Load 2

Live Load Diagram

Max: 1.097 mm

Y
X Load 3 : Displacement
Z Displacement - mm

Deflection Diagram (DL+LL)

Page 44
 Max: 61.782 N/mm2

Max: -61.782 N/mm2

Y
X Load 4 : Beam Stress
Z Stress - N/mm2

Stress Diagram (1.2DL+1.6LL)

Page 45
 Max: -9.979 kNm

Y
X Load 4 : Bending Z
Z Moment - kNm

Bending Moment Diagram (1.2DL+1.6LL)

Page 46
 Max: -8.11

Max: 8.119 kN

Y
X Load 4 : Shear Y
Z Force - kN

Shear Diagram (1.2DL+1.6LL)

Page 47
 Y = 5.131 kN

Y = 5.131 kN

Y
X
Z Load 3

Support Reactions (DL+LL)

Y = 8.119 kN

Y = 8.119 kN

Y
X
Z Load 4

Support Reactions (1.2DL+1.6LL)

Page 48
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 IPEA200 IPEA200 0.224 1.000 0.224 BS-4.3.6 4 23.500 1.59E+3 117.000 4.100
2 IPEA200 IPEA200 0.224 1.000 0.224 BS-4.3.6 4 23.500 1.59E+3 117.000 4.100

Page 49
Steel Design (Track 2) Beam 1 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

1 ST IPEA200 PASS BS-4.3.6 0.224 4

0.00 0.00 9.98 0.00
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 125.00
Gross Area = 23.50 Net Area = 23.50 Eff. Area = 23.50

z-z axis y-y axis

Moment of inertia : 1591.000 117.000
Plastic modulus : 182.000 37.000
Elastic modulus : 161.523 23.400
Effective modulus : 182.000 37.000
Shear Area : 12.600 8.865

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : PLASTIC

z-z axis y-y axis

Moment Capacity : 50.1 9.7
Reduced Moment Capacity : 50.1 9.7
Shear Capacity : 207.9 146.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)

LTB Moment Capacity (kNm) and LTB Length (m): 44.61, 1.250
LTB Coefficients & Associated Moments (kNm):
mLT = 1.00 : mx = 0.00 : my = 0.00 : myx = 0.00
Mlt = 9.98 : Mx = 0.00 : My = 0.00 : My = 0.00

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.056 4 - 8.1 - - -
BS-4.3.6 0.224 4 - 8.1 - 10.0 -
Torsion and deflections have not been considered in the design.

Page 50
Steel Design (Track 2) Beam 2 Check 1
ALL UNITS ARE - KN METE (UNLESS OTHERWIS E Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

2 ST IPEA200 PASS BS-4.3.6 0.224 4

0.00 0.00 9.98 0.00
=======================================================================
MATERIAL DATA
Grade of steel = S 275
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 275 N/mm2

SECTION PROPERTIES (units - cm)

Member Length = 125.00
Gross Area = 23.50 Net Area = 23.50 Eff. Area = 23.50

z-z axis y-y axis

Moment of inertia : 1591.000 117.000
Plastic modulus : 182.000 37.000
Elastic modulus : 161.523 23.400
Effective modulus : 182.000 37.000
Shear Area : 12.600 8.865

DESIGN DATA (units - kN,m) BS5950-1/2000

Section Class : PLASTIC

z-z axis y-y axis

Moment Capacity : 50.1 9.7
Reduced Moment Capacity : 50.1 9.7
Shear Capacity : 207.9 146.3

BUCKLING CALCULATIONS (units - kN,m)

(axis nomenclature as per design code)

LTB Moment Capacity (kNm) and LTB Length (m): 44.61, 1.250
LTB Coefficients & Associated Moments (kNm):
mLT = 1.00 : mx = 0.00 : my = 0.00 : myx = 0.00
Mlt = 9.98 : Mx = 0.00 : My = 0.00 : My = 0.00

CRITICAL LOADS FOR EACH CLAUSE CHECK (units- kN,m):

CLAUSE RATIO LOAD FX VY VZ MZ MY

BS-4.2.3-(Y) 0.056 4 - 8.1 - - -
BS-4.3.6 0.224 4 - 7.8 - 10.0 -
Torsion and deflections have not been considered in the design.

Page 51
Structural Check for STEEL BEAM

Deflection Check:

Max Deflection of Cantilever: δMax  1.09mm

2500
Deflection limit: δcap  mm  12.5 mm
200
δ Max  δcap "Therefore OK"

Stress Check:
Maximum Stress σ Max  61.78 MPa

Steel Grade 275 Tensile Strength py  275MPa

Stress Capacity σ Cap  py  275.00 MPa

σ Max  σ Cap "Therefore OK"

Page 52
DESIGN OF CONNECTION
COMPONENTS

Page 53
Pipe to steel beam connection:

Support Reactions

The following reaction is obtained from STAAD Report for beam

Reaction along y-axis
Ry  8.12kN

Bolt Properties:
M12 Stainless Steel Bolt and Nut with Washers Grade A4-70
Nominal bolt diameter
db  10 mm

2
Tensile stress area As  58 mm

Proof stress Yb  450MPa

Tensile Stress
Ub  700MPa

Tensile Load Check

Number of bolts
nb  4

Ry
Tensile load per bolt ftsd   2.03 kN
nb

Bolt tensile load capacity

ftcap  0.8 Yb As  20.88 kN

ftsd  ftcap  Therefore OK

Page 54
Check for Fabricated Steel Plate
Bending Moment Check:

Number of plate per side

nf  2

Load eccentricity to the edge of plate e  ( 73  36)mm  37.00 mm

e
Factored bending moment on plate
Mzsd  Ry   0.15 kN  m
nf

Plate thickness
tf  8mm

Plate depth
bf  100mm

2
tf
3
Section modulus at strong axis Zz  bf   1.07 cm
6

Steel yield strength Py  275MPa

Material factor
γM  1.1
Zz  Py
Bending moment capacity of plate
Mzcap   0.27 kN  m
γM

''Steel plate meets the design requirements, OK''

Mcap  Mzsd

Adopt 8mm thk. Steel Plate, Grade S275

Page 55
Bracket Design

Support Reactions:
Reaction along Y-axis Ry  11.719kN
See STAAD report
page 12
Reaction along X-axis Rx  0.3kN

Hilti Input:
Compressive Force Fz  Ry  11.72  kN

Shear Force Fx  Rx  0.30 kN

Find the attached hilti report

Adopt 4 HST3-R M10 hef2 Anchor Bolts

Page 56
www.hilti-me.com Profis Anchor 2.7.5
Company: Page: 1
Specifier: Project:
Address: Fastening Point:
Phone I Fax: | Date: 14/08/2018
E-Mail:

Specifier's comments:

1 Input data
Anchor type and size: HST3-R M10 hef1
Effective embedment depth: hef = 40 mm, hnom = 48 mm
Material: A4
Approval No.: ETA-98/0001
Issued I Valid: 28/07/2016 | -
Proof: Design method ETAG (No. 001 Annex C/2010)
Stand-off installation: eb = 0 mm (no stand-off); t = 10 mm
Baseplate: S275; E = 210000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.100
lx x ly x t = 150 mm x 150 mm x 10 mm; (Recommended plate thickness: calculated (6 mm))
Profile: Pipe; (L x W x T) = 50 mm x 50 mm x 3 mm
Base material: cracked concrete, C25/30, fc,cube = 30.00 N/mm2; h = 250 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: No reinforcement or Reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement

Geometry [mm] & Loading [kN, kNm]

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.7.5
Company: Page: 2
Specifier: Project:
Address: Fastening Point:
Phone I Fax: | Date: 14/08/2018
E-Mail:

2 Load case/Resulting anchor forces y

Load case: Design loads
3 4
Anchor reactions [kN]
Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 0.000 0.075 0.075 0.000
2 0.000 0.075 0.075 0.000 x
Compression
3 0.000 0.075 0.075 0.000
4 0.000 0.075 0.075 0.000

max. concrete compressive strain: 0.02 [‰]

max. concrete compressive stress: 0.52 [N/mm2] 1 2
resulting tension force in (x/y)=(0/0): 0.000 [kN]
resulting compression force in (x/y)=(0/0): 11.720 [kN]

3 Tension load (ETAG, Annex C, Section 5.2.2)

Load [kN] Capacity [kN] Utilisation bN [%] Status
Steel failure* N/A N/A N/A N/A
Pull-out failure* N/A N/A N/A N/A
Concrete cone failure** N/A N/A N/A N/A
Splitting failure** N/A N/A N/A N/A
* most unfavourable anchor **anchor group (anchors in tension)

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.7.5
Company: Page: 3
Specifier: Project:
Address: Fastening Point:
Phone I Fax: | Date: 14/08/2018
E-Mail:

4 Shear load (ETAG, Annex C, Section 5.2.3)

Load [kN] Capacity [kN] Utilisation bV [%] Status
Steel failure (without lever arm)* 0.075 20.480 1 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout failure** 0.300 59.688 1 OK
Concrete edge failure in direction ** N/A N/A N/A N/A
* most unfavourable anchor **anchor group (relevant anchors)

4.1 Steel failure (without lever arm)

VRk,s [kN] gM,s VRd,s [kN] VSd [kN]
25.600 1.250 20.480 0.075

4.2 Pryout failure

Ac,N [mm2] A0c,N [mm2] ccr,N [mm] scr,N [mm] k-factor
48400 14400 60 120 2.670
ec1,V [mm] y ec1,N ec2,V [mm] y ec2,N y s,N y re,N
0 1.000 0 1.000 1.000 1.000
N0Rk,c [kN] gM,c,p VRd,cp [kN] VSd [kN]
9.977 1.500 59.688 0.300

5 Displacements (highest loaded anchor)

Short term loading:
NSk = 0.000 [kN] dN = 0.000 [mm]
VSk = 0.056 [kN] dV = 0.014 [mm]
dNV = 0.014 [mm]
Long term loading:
NSk = 0.000 [kN] dN = 0.000 [mm]
VSk = 0.056 [kN] dV = 0.021 [mm]
dNV = 0.021 [mm]

Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the baseplate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!

The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!

6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is
assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum
required anchor plate thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the
rigid base plate assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the
existing conditions and for plausibility! 
• Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software
considers that the grout is installed under the baseplate without creating air voids and before application of the loads.
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of ETAG 001, Annex C! For larger
diameters of the clearance hole see Chapter 1.1. of ETAG 001, Annex C!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.

Fastening meets the design criteria!

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.7.5
Company: Page: 4
Specifier: Project:
Address: Fastening Point:
Phone I Fax: | Date: 14/08/2018
E-Mail:

7 Installation data
Baseplate, steel: S275; E = 210000.00 N/mm2; fyk = 275.00 N/mm2 Anchor type and size: HST3-R M10 hef1
Profile: Pipe; 50 x 50 x 3 mm Installation torque: 0.045 kNm
Hole diameter in the fixture: df = 12 mm Hole diameter in the base material: 10 mm
Plate thickness (input): 10 mm Hole depth in the base material: 55 mm
Recommended plate thickness: calculated (6 mm) Minimum thickness of the base material: 80 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.

7.1 Recommended accessories

Drilling Cleaning Setting

• Suitable Rotary Hammer • Manual blow-out pump • Torque wrench
• Properly sized drill bit • Hammer
y

75 75

25
3 4

75
100

x
75

1 2
25

25 100 25

Coordinates Anchor [mm]

Anchor x y c-x c+x c-y c+y
1 -50 -50 - - - -
2 50 -50 - - - -
3 -50 50 - - - -
4 50 50 - - - -

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti-me.com Profis Anchor 2.7.5
Company: Page: 5
Specifier: Project:
Address: Fastening Point:
Phone I Fax: | Date: 14/08/2018
E-Mail:

8 Remarks; Your Cooperation Duties

• Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas
and security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be
strictly complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted
prior to using the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the
data you put in. Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be
put in by you. Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly
with regard to compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an
aid to interpret norms and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or
suitability for a specific application.
• You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for
the regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do
not use the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software
in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or
damaged data or programs, arising from a culpable breach of duty by you.

Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
 HST3 (-R) subject to:
Anchor size M8 M10 M12 M16 M20 M24
Hammer drilling*

TE2(-A) – TE30(-A) TE40 – TE70

Diamond core drilling*

DD-30W, DD-EC1

Setting tool*
Setting tool HS-SC -

Hollow drill bit drilling*

- TE-CD, TE-YD

Seismic Set/ Filling Set**

Seismic/Filling Set M8-M20 (Carbon and Stainless Steel A4) -

*Installation methods provided in ETA-98/0001

**Seismic set needed to fill the annular gap between anchor and fixture:
No annular gap, double design resistance (αgap=1)