Scribd
Upload
118 views

How To Build 1wamp PDF

The document provides instructions for building a 1W amplifier (1Wamp) in 5 steps: 1) Prepare materials like a solder iron, lead, and cutting pliers. 2) Solder resistors and diodes, paying attention to polarity. 3) Solder capacitors, starting with smaller film caps and finishing with electrolytic caps. 4) Solder remaining components like an 8-pin socket, LED, and transistors. 5) Solder larger components like jacks, pots, switch, and power connector. Check for errors before powering on.

Uploaded by

Víctor Faucheret
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
118 views

How To Build 1wamp PDF

The document provides instructions for building a 1W amplifier (1Wamp) in 5 steps: 1) Prepare materials like a solder iron, lead, and cutting pliers. 2) Solder resistors and diodes, paying attention to polarity. 3) Solder capacitors, starting with smaller film caps and finishing with electrolytic caps. 4) Solder remaining components like an 8-pin socket, LED, and transistors. 5) Solder larger components like jacks, pots, switch, and power connector. Check for errors before powering on.

Uploaded by

Víctor Faucheret
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

www.ElectroSmash.

com/1Wamp

How to Build 1Wamp in 5 Steps


With all the materials on hand it takes around 3 hours to build it successfully, do not rush and take your
time to do it because it is fun, a nice weekend project.
The main idea is to start with the small components and then place the big ones, making all the process
easier.
Have a quick read to the whole document before starting, it is very sort and it definitely will help you to
build it.

Step 0 – Prepare the Materials.

You need a solder iron, lead and cutting pliers.


The PCB has solder mask and plated holes, so it is easy to
solder with any 15-30W cheap solder iron.
www.ElectroSmash.com/1Wamp

Keep in short hand the PCB plan and the Bill of Materials:

1Wamp Bill of Materials


Reference Qty Value
Capacitors
C1 1 6.8n
C2 1 10n
C3,C4,C6 3 47n
C5,C11,C12 3 100n
C7,C8,C9,C10 4 220uF
Resistors
R12 1 10R
R13,R15,R16 3 1K
R3,R8 2 2K2
R2, R7, R11 3 6K8
R5,R9,R10,R14 4 22K
R4 1 47K
R1,R6 2 1M
Pot1, Pot2, Pot3 3 50K
Connectors
CON1, CON3 2 6.35 jack.
CON2 1 3.5 jack
CONN4 1 2.1mm conn.
Others
D1 1 1N5817
D2 1 LED
D3,D4 2 1N4733A
8pin dip socket 1 8Pin socket
Q1,Q2 2 J201
Plastic Knobs 3 6.35mm knob.
SW1 1 toggle switch
9V Battery Conn. 1 Battery Clip
U1 1 LM386
Mechanical
PCB 1 1Wamp PCB
Plexiglas Cover 2 -
Nylon Spacer 4 m3x16
M3x12 screws 8 -
Batt. optional clips 2 -

* Additional Comp.
R2, R7 2 10K
R3, R8 2 1K

R3 & R8 R2 & R7
* R2, R3, R7 and R8 could be modified to implement
Tillman Amp 2K2 6K8
different gain stages:
Fetzer Valve 1K 10K
JFET Low Gain 1K 2K2
www.ElectroSmash.com/1Wamp

Step 1 – Soldering Resistors and Diodes.


There are 16 resistors and 3 diodes to be placed.

tips:
- Pay attention to diodes polarity, there is a line indicating the correct position. They get hot very fast
when soldering, so try to do it carefully and wait between each solder point.

- In order to solder the components, bend the leads, introduce


them in the footprint and once soldered cut the excess of lead as
short as possible to avoid short circuits.

- Bend the legs as close as possible to the body because the


footprint on the PCB is optimized for compact placement.
www.ElectroSmash.com/1Wamp

Step 2 – Soldering the Capacitors.


There are 8 film and 4 electrolytic caps.

Solder the film caps first (6.8nF, 10nF, 47nFx3, 100nFx3) and finish with the big electrolytic capacitors
(220uFx4)

You can zoom over the above image to even see the components code value.

tips:
- Be careful with the electrolytic caps polarity, the negative lead (the short one) has to be placed in the
round hole. The positive hole is always square-shaped and it is marked with a + symbol.
www.ElectroSmash.com/1Wamp

Step 3 – Soldering the Socket, LED and Transistors.


The is one 8-pin socket, one LED and 2 transistors:

tips:
• To solder the LED D2, place the plastic cover or enclosure to size the length of the leads.
The short lead (cathode) goes to the flat side of the diode mark.
www.ElectroSmash.com/1Wamp

Step 4 – Soldering the Big Components.


The last components to be placed are the jack connectors (2), potentiometers (3), toggle-switch, mini-
jack, the power connector and the battery clip.

If you intend to place the amp in a closed enclosure, it is a good idea to check the position of
potentiometers and switches against the cover before solder them.

Big components with big terminal get pretty hot during soldering, so take your time to avoid over-
heating them.

tips:
– Be careful soldering the big components perpendicularly because they tend to be slightly tilted.
www.ElectroSmash.com/1Wamp

Step 5 – Checking Out the Job Done.


After this 5 stages you will have a mounted board exactly like the one shown below:

Double check your PCB with the model component by component, before power it up, check this 3 ticks:
☑ 1. Visual inspection of the PCB bottom, there is no short circuits or long uncut leads.
☑ 2. The polarized components are placed correctly: diodes and electrolytic caps.
☑ 3. The parts are not swapped or wrongly placed.

Finally the plastic covers can be


installed together with 8 screws + 4
spacers.

The plastic knobs are the last parts to


be mounted.
www.ElectroSmash.com/1Wamp

Appendix: 1Wamp Schematic and Layout.

You might also like