Scribd
Upload
62 views

GPS310 PDF

This document provides specifications for a 3-way GPS signal splitter, including both electrical and mechanical specifications. The splitter operates at frequencies between 1000-2000 MHz with impedances of 50 ohms. It has an insertion loss of less than 0.4 dB, amplitude and phase balances of less than 0.2 dB and 5 degrees, respectively. Mechanically, it uses SMA female connectors with brass and beryllium copper components housed in an aluminum casing. It can withstand temperatures from -65 to 85 degrees Celsius and weighs 292 grams.

Uploaded by

cristofer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
62 views

GPS310 PDF

This document provides specifications for a 3-way GPS signal splitter, including both electrical and mechanical specifications. The splitter operates at frequencies between 1000-2000 MHz with impedances of 50 ohms. It has an insertion loss of less than 0.4 dB, amplitude and phase balances of less than 0.2 dB and 5 degrees, respectively. Mechanically, it uses SMA female connectors with brass and beryllium copper components housed in an aluminum casing. It can withstand temperatures from -65 to 85 degrees Celsius and weighs 292 grams.

Uploaded by

cristofer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

ELECTRICAL SPECIFICATIONS: MECHANICAL SPECIFICATIONS:

1.) FREQUENCY RANGE: 1000 - 2000 MHz 1.) CONNECTORS: SMA FEMALE (JACK), 50 OHM
2.) IMPEDANCE: 50 OHMS 2.) CONNECTOR BODY: BRASS, TRI-ALLOY PLATE
3.) INSERTION LOSS (MAX): 0.4 dB (ABOVE 4.77 dB SPLIT) 3.) CONNECTOR PIN: BERYLLIUM COPPER, GOLD PLATE
4.) AMPLITUDE BALANCE (MAX): 0.2 dB 4.) INSULATOR: PTFE, VIRGIN ELECTRICAL GRADE
5.) PHASE BALANCE (MAX): 5 DEGREES 5.) HOUSING: ALUMINUM, CLEAR CHEM CONVERSION
6.) ISOLATION (MIN): 20 dB FILM, RoHS COMPLIANT (NO HEX CHROM)
7.) INPUT VSWR (MAX): 1.20 : 1 6.) SOLDER: LEAD FREE, RoHS COMPLIANT
8.) OUTPUT VSWR (MAX): 1.25 : 1 7.) OPERATING TEMP: -65°C TO +85°C
9.) DC VOLTAGE (MAX): 10 V 8.) WEIGHT: 292 GRAMS
10.) DC CURRENT (MAX): 50 mA

GPS INPUT POWER RATING (GPS DIVIDER SPLITTER): GPS INPUT POWER RATING (GPS COMBINER):
INTO MATCHED LOAD VSWR's IN-PHASE 180° OUT-OF-PHASE COHERENT SIGNALS (IN-PHASE) 3 X 6.67 WATTS
1.2 : 1 20 WATTS 20 WATTS COHERENT SIGNALS (180° OUT-OF-PHASE) 3 X 0.33 WATTS
2.0 : 1 20 WATTS 10 WATTS NON-COHERENT SIGNALS 3 X 0.67 WATTS
∞ 10 WATTS 1 WATT OTHER CONDITIONS - CONSULT FACTORY

1.49
[37.8] .50
2.750
[12.7]
[69.85]
.12
[2.9] .44
[11.1]
DC PASS

2.98
[75.7]

Ø.125
[Ø3.18]
SIGNAL SPLITTER THRU, 2X
1.49
[37.8] instockwireless.com
DC BLOCK DC BLOCK
DC PASS W/200Ω LOAD W/200Ω LOAD

1.000
.49
[25.40] SMA-JACK, .88
[12.4]
2X 2.98 4X [22.2]
[75.7]

3-way, GPS signal splitter; DC pass 1 port, DC block 2 ports w/200Ω loads. Typically
used for powering an active antenna thru pass ports while splitting GPS signal 3 ways.
TOLERANCES MODEL NO.
INCHES MILLIMETERS
.00 = ±.01 .0 = ±.25
.000 = ±.004 .00 = ±.10 TITLE GPS SPLITTER, 3 WAY, SMA FEMALE,
DRAWN: MJD APPROVED: EMM 1 - 2 GHz, 20 WATTS, RoHS, DC BLOCK
REV DESCRIPTION BY DATE DATE: 06/11/08 DATE: 06/11/08 www.instockwireless.com 2 PORTS, WITH 200Ω INTERNAL LOADS

You might also like