FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.

0 (480Mbps) UART Switch

FSUSB42 — Low-Power, Two-Port, High-Speed,
USB2.0 (480Mbps) UART Switch

Features Description
 Low On Capacitance: 3.7 pF Typical The FSUSB42 is a bi-directional, low -pow er, tw o-port,
 Low On Resistance: 3.9 Ω Typical high-speed, USB2.0 sw itch. Configured as a double-
 Low Pow er Consumption: 1 μA Maximum pole, double-throw sw itch (DPDT) sw itch, it is optimized
- 15 μA Maximum ICCT over an Expanded Voltage for sw itching betw een any combination of high-speed
Range (V IN=1.8 V, V CC=4.4 V) (480 Mbps) or Full-Speed (12 Mbps) sources.
 Wide -3 db Bandw idth: > 720 MHz The FSUSB42 is compatible w ith the requirements of
 Packaged in: USB2.0 and features an extremely low on capacitance
- 10-Lead UMLP (1.4 x 1.8 mm) (CON) of 3.7 pF. The w ide bandw idth of this device
(720 MHz) exceeds the bandw idth needed to pass the
- 10-Lead MSOP third harmonic, resulting in signals w ith minimum edge
 8 kV ESD Rating, >16 kV Pow er / GND ESD Rating and phase distortion. Superior channel-to-channel
 Over-Voltage Tolerance (OVT) on all USB Ports crosstalk also minimizes interference.
Up to 5.25 V w ithout External Components
The FSUSB42 contains special circuitry on the sw itch
I/O pins for applications w here the V CC supply is
Applications pow ered-off (V CC=0 V), w hich allow s the device to
w ithstand an over-voltage condition. This device is
 Cell phone, PDA, Digital Camera, and Notebook designed to minimize current consumption even w hen
 LCD Monitor, TV, and Set-Top Box the control voltage applied to the SEL pin is low er than
the supply voltage (V CC). This feature is especially
valuable to ultra-portable applications, such as cell
phones, allow ing for direct interface w ith the general-
purpose I/Os of the baseband processor. Other
applications include sw itching and connector sharing in
portable cell phones, PDAs, digital cameras, printers,
and notebook computers.

Ordering Information

Part Number Top Mark Operating Temperature Package

Range
FSUSB42UMX HE -40 to +85°C 10-Lead, Quad, Ultrathin Molded Leadless Package
(UMLP), 1.4 x 1.8 mm
10-Lead, Molded Small-Outline Package (MSOP)
FSUSB42MUX FSUSB42 -40 to +85°C
JEDEC MO-187, 3.0 mm Wide

HSD1+
D+
HSD2+

HSD1-
D-
HSD2-

Sel Control /OE

Figure 1. Analog Sym bol

© 2007 Semiconductor Components Industries, LLC. Publication Order Number:

October-2017, Rev. 2 FSUSB42/D
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
Pin Assignments

VCC 1 10 /OE

D- D+ Sel 2 9 HSD2+
2 1
GND 3 10 Sel
HSD1- 4 9 Vcc D+ 3 8 HSD2-

HSD1+ 5 6 7 8 /OE
D- 4 7 HSD1+
HSD2- HSD2+

GND 5 6 HSD1-

Figure 2. 10-Lead UMLP (Top-Through View ) Figure 3. 10-Lead MSOP (Top-Through View )

Pin Definitions
UMLP Pin# MSOP Pin# Name Description
1 3 D+ Common USB Data Bus
2 4 D- Common USB Data Bus
3 5 GND Ground
4 6 HSD1- Multiplexed Source Input 1
5 7 HSD1+ Multiplexed Source Input 1
6 8 HSD2- Multiplexed Source Input 2
7 9 HSD2+ Multiplexed Source Input 2
8 10 /OE Sw itch Enable
9 1 V CC Supply Voltage
10 2 Sel Sw itch Select

Truth Table
SEL /OE Function
X HIGH Disconnect
LOW LOW D+= HSD1+, D-= HSD1-
HIGH LOW D+= HSD2+, D-= HSD2-
Notes:
1. LOW ≤V IL.
2. HIGH ≥V IH.
3. X=Don’t Care.

www.onsemi.com
2
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.

Symbol Parameter Min. Max. Unit

V CC Supply Voltage -0.5 5.6 V
(4)
V CNTRL DC Input Voltage (S, /OE) -0.5 V CC V
(4)
V SW DC Sw itch I/O Voltage (VCC=0V) -0.50 5.25 V
IIK DC Input Diode Current -50 mA
IOUT DC Output Current 100 mA
TSTG Storage Temperature -65 +150 °C
MSL Moisture Sensitivity Level (JEDEC J-STD-020A) 1 Level
All Pins 7

I/O to GND 8
Human Body Model, JEDEC: JESD22-A114
Pow er to GND 16

ESD D+/D- 9 kV

IEC 61000-4-2 System on USB Connector Air Discharge 15

Pins D+ & D- Contact 8
Charged Device Model, JEDEC: JESD22-C101 2
Note:
4. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed.

Recommended Operating Conditions

The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. ON Semiconductor
does not recommend exceeding them or designing to Absolute Maximum Ratings.

Symbol Parameter Min. Max. Unit

V CC Supply Voltage 2.4 4.4 V
(5)
V CNTRL Control Input Voltage (S, /OE) 0 V CC V
V SW Sw itch I/O Voltage -0.5 4.5 V
TA Operating Temperature -40 +85 °C
Note:
5. The control input must be held HIGH or LOW and it must not float.

www.onsemi.com
3
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
DC Electrical Characteristics
All typical value are at TA=25°C unless otherw ise specified.

TA=- 40°C to +85°C

Symbol Parameter Condition VCC (V) Unit
Min. Typ. Max.
V IK Clamp Diode Voltage IIN=-18mA 3.0 -1.2 V
2.4 to 3.6 1.3
V IH Input Voltage High V
4.3 1.7
2.4 to 3.6 0.5
V IL Input Voltage Low V
4.3 0.7

IIN Control Input Leakage V SW=0 to V CC 0 to 4.3 -1 1 µA

0 Dn, HSD1n, HSD2n

IOZ Off State Leakage 4.3 -2 2 µA
3.6 V
Pow er-Off Leakage Current V SW=0 V to 4.3 V, V CC=0 V
IOFF 0 -2 2 µA
(All I/O Ports) Figure 5

(6) V SW=0.4 V, ION=-8 mA 2.4 4.5 7.5

RON HS Sw itch On Resistance
Figure 4 
3.0 3.9 6.5
(7)
∆RON HS Delta RON V SW=0.4 V, ION=-8 mA 3.0 0.65 
ICC Quiescent Supply Current V CNTRL=0 or V CC, IOUT=0 4.3 1 µA

Increase in ICC Current per V CNTRL=2.6 V, V CC=4.3 V 4.3 10 µA

ICCT
Control Voltage and V CC V CNTRL=1.8 V, V CC=4.3 V 4.3 15 µA
Notes:
6. Measured by the voltage drop betw een HSDn and Dn pins at the indicated current through the sw itch.
On resistance is determined by the low er of the voltage on the tw o (HSDn or Dn ports).
7. Guaranteed by characterization.

www.onsemi.com
4
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
AC Electrical Characteristics
All typical value are for V CC=3.3 V at TA=25°C unless otherw ise specified.

TA=- 40°C to +85°C

Symbol Parameter Condition VCC (V) Unit
Min. Typ. Max.
Turn-On Time RL=50 Ω, CL=5 pF, V SW=0.8 V, 2.4 24 40
tON ns
S, /OE to Output Figure 6, Figure 7 3.0 to 3.6 13 30
Turn-Off Time RL=50 Ω, CL=5 pF, V SW=0.8 V, 2.4 15 35
tOFF ns
S, /OE to Output Figure 6, Figure 7 3.0 to 3.6 12 25

tPD Propagation Delay

8 CL=5 pF, RL=50 Ω, Figure 6, 3.3 0.25 ns
Figure 8
RL=50 Ω, CL=5 pF, 2.4 2.0 10
tBBM Break-Before-Make ns
V SW1=V SW2=0.8 V, Figure 10 3.0 to 3.6 2.0 6.5
OIRR Off Isolation RL=50 Ω, f=240 MHz, Figure 12 3.0 to 3.6 -30 dB

Xtalk Non-Adjacent Channel RL=50 Ω, f=240 MHz, Figure 13 3.0 to 3.6 -45 dB
Crosstalk
RL=50 Ω, CL=0 pF, Figure 11 720 MHz
BW -3db Bandw idth 3.0 to 3.6
RL=50 Ω, CL=5 pF, Figure 11 550 MHz
Note:
8. Guaranteed by characterization.

USB High-Speed-Related AC Electrical Characteristics

All typical value are for V CC=3.3 V at TA=25°C unless otherw ise specified.

TA=- 40ºC to +85ºC

Symbol Parameter Condition VCC (V) Unit
Min. Typ. Max.

tSK(P) Skew of Opposite Transitions of CL=5 pF, RL=50 Ω, Figure 9 20 ps

(9)
the Same Output
RL=50 Ω, CL=5 pF,
(9)
tJ Total Jitter tR=tF=500 ps (10-90%) at 200 ps
15
480 Mbps (PRBS=2 – 1)
Note:
9. Guaranteed by characterization.

Capacitance
TA=- 40°C to +85°C
Symbol Parameter Condition Unit
Min. Typ. Max.
CIN Control Pin Input Capacitance V CC=0 V 1.5
V CC=3.3 V, /OE=0 V, f=240 MHz,
CON D+/D- On Capacitance 3.7 pF
Figure 15
COFF D1n, D2n Off Capacitance V CC and /OE=3.3 V, Figure 14 2.0

www.onsemi.com
5
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
Test Diagrams

VON
NC I Dn(OFF)
A
HSDn
Dn VSW
VSW Select
GND
I ON
GND
Select V Sel = 0 orV
V cc
GND

V Sel = 0 orV cc **Each switch port is tested separately

R ON = VON / ION

Figure 4. On Resistance Figure 5. Off Leakage

HSDn
Dn tRISE = 2.5ns tFALL = 2.5ns
VSW
V OUT VCC
GND RS CL RL 90% 90%
Input – V/OE , VSel
GND VCC /2 VCC /2
10% 10%
GND
V Sel VOH
90% 90%
GND Output- VOUT

RL , RS , and C L are functions of the application VOL

tON tOFF
environment (see AC Tables for specific values)
CL includes test fixture and stray capacitance.

Figure 6. AC Test Circuit Load Figure 7. Turn-On / Turn-Off Waveform s

tRISE = 500ps tFALL = 500ps

+400mV
90% 90%
0V
10% 10%
- 400mV

Output

t PHL t PLH

Figure 8. Propagation Delay (t Rt F – 500 ps) Figure 9. Intra-Pair Skew Test t SK(P)

www.onsemi.com
6
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
Test Diagrams (Continued)
tRISE = 2.5ns

Vcc
HSDn 90%
Dn Input - VSel Vcc/2
VSW1 10%
VOUT 0V
GND VSW2 CL RL V OUT
GND
GND 0.9*Vout 0.9*Vout
RS
tBBM

VSel RL , RS , and C L are functions of the application

GND environment (see AC Tables for specific values)
CL includes test fixture and stray capacitance.

Figure 10. Break-Before-Make Interval Tim ing

Network Analyzer Network Analyzer

RS RS

V IN V IN
GND VS RT GND VS

GND GND
VSel VSel GND
V OUT
GND VOUT GND
GND RT
GND RT
RS and RT are functions of the application
GND
GND environment (see AC Tables for specific values).
RS and RT are functions of the application
environment (see AC Tables for specific values). Off isolation = 20 Log (V OUT / VIN)

Figure 11. Bandw idth Figure 12. Channel Off Isolation

Network Analyzer
NC RS

V IN
GND VS

VSel GND

GND RT

GND

V OUT
GND RT
RS and RT are functions of the application environment
(see AC Tables for specific values). GND

Crosstalk = 20 Log (VOUT / VIN)

Figure 13. Non-Adjacent Channel-to-Channel Crosstalk

Capacitance
Capacitance
Meter HSDn
Meter HSDn

S=LOW or HIGH S=LOW or HIGH

OE=HIGH OE=LOW

Dn Dn

Figure 14. Channel Off Capacitance Figure 15. Channel On Capacitance

www.onsemi.com
7
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
Physical Dimensions

0.05 C 1.40 A
B
2X

1.80
1.70 (9X)
PIN#1 IDENT
0.663 0.563
0.05 C
TOP VIEW
2X 1
2.10
0.50±.05 0.15±.05
0.10 C 0.40

(10X) 0.225
0.08 C
SEATING C RECOMMENDED
0.025±.025 PLANE LAND PATTERN
SIDE VIEW 9X
1.45
0.55 0.45
1.40±.05
0.40±.05 (0.20) 4X
(9X) 3 0.40 1.85
0.40
6
DETAIL A
1 1.80±.05 (10X) 0.225
PIN#1 IDENT (0.60) 4X OPTIONAL MINIMIAL
10 TOE LAND PATTERN
0.20±.05 (10X)
NOTES:
0.10 C A B
BOTTOM VIEW A. PACKAGE DOES NOT CONFORM TO
0.05 C ANY JEDEC STANDARD.
B. DIMENSIONS ARE IN MILLIMETERS.

1.00±.05 C. DIMENSIONS AND TOLERANCES PER

ASME Y14.5M, 2009.
D. LAND PATTERN RECOMMENDATION IS
45° EXISTING INDUSTRY LAND PATTERN.
0.40±.05 E. DRAWING FILENAME: MKT-UMLP10Arev6.
DETAIL A
SCALE : 2X

PACKAGE
EDGE

LEAD LEAD
OPTION 1 OPTION 2
SCALE : 2X SCALE : 2X
Figure 16. 10-Lead, Ultrathin Molded Leadle ss Package (UMLP)

www.onsemi.com
8
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
Physical Dimensions (Continued)

Figure 17. 10-Lead, Molded Sm all Outline Package (MSOP)

www.onsemi.com
9
 FSUSB42 — Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the
United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A
listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make
changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or ci rcuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor
products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by
ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and
actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts.
ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for
use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or
any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distr ibutors harmless against all claims, costs,
damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor N. Amer ican Technical Support: 800-282-9855 Toll Free ON Semiconductor Website: www.onsemi.com
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA USA/Canada.
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Eur ope, Middle East and Afr ica Technical Support: Or der Literature: http://www.onsemi.com/orderlit
Fax : 303-675-2176 or 800-344-3867 Toll Free USA/Canada Phone: 421 33 790 2910
Email: [email protected] Japan Customer Focus Center For additional information, please contact your local
Phone: 81-3-5817-1050 Sales Representative

www.onsemi.com
10