TP48200A-DX12A1 Telecom Power

User Manual

Issue 07

Date 2019-11-15

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China

Website: https://e.huawei.com

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. i

TP48200A-DX12A1 Telecom Power
User Manual Preface

Preface

Purpose
This document describes the DC power system in terms of product introduction, component
introduction, and system maintenance.
Figures provided in this document are for reference only.

Intended Audience
This document is intended for:
 Sales engineers
 Technical support engineers
 Maintenance engineers

Symbol Conventions
The symbols that may be found in this document are defined as follows.

Symbol Description
Indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.
Indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.
Indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, could
result in equipment damage, data loss, performance deterioration, or
unanticipated results.
NOTICE is used to address practices not related to personal injury.
Supplements the important information in the main text.
NOTE is used to address information not related to personal injury,
equipment damage, and environment deterioration.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. ii

TP48200A-DX12A1 Telecom Power
User Manual Preface

Change History
Changes between document issues are cumulative. The latest document issue contains all
updates made in previous issues.

Issue 07 (2019-11-15)
Deleted contents about the app.
Optimized the content about rectifiers.

Issue 06 (2019-02-26)
Optimized the content of the document.

Issue 05 (2017-03-20)
Modified appendix A.3 EMC Specifications.

Issue 04 (2016-02-05)
Modified all the cabinet figures.

Issue 03 (2016-01-12)
Modified appendix C Associations Between Alarms and Dry Contacts on the UIM.

Issue 02 (2015-11-24)
Modified all the cabinet figures.
Modified section 2.3 System Configurations.
Modified section 4.2.20 Batt Test Negative.

Issue 01 (2015-11-15)
This issue is the first official release.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. iii

 TP48200A-DX12A1 Telecom Power
User Manual Contents

Contents

Preface ............................................................................................................................................... ii
1 Safety Precautions ......................................................................................................................... 1
1.1 General Safety .............................................................................................................................................................. 1
1.2 Personnel Requirements ............................................................................................................................................... 5
1.3 Electrical Safety ............................................................................................................................................................ 5
1.4 Installation Environment Requirements ....................................................................................................................... 7
1.5 Mechanical Safety ........................................................................................................................................................ 8
1.6 Battery Safety ............................................................................................................................................................. 11

2 Overview....................................................................................................................................... 15
2.1 Introduction ................................................................................................................................................................ 15
2.2 Features ....................................................................................................................................................................... 16
2.3 System Configurations ................................................................................................................................................ 16

3 Components ................................................................................................................................. 18
3.1 Interior ........................................................................................................................................................................ 18
3.2 Power Distribution Unit .............................................................................................................................................. 22
3.3 Rectifier ...................................................................................................................................................................... 22
3.4 SMU02B ..................................................................................................................................................................... 23
3.5 User Interface Module UIM02C ................................................................................................................................. 27
3.6 (Optional) Heater ........................................................................................................................................................ 30
3.7 Door Status Sensor...................................................................................................................................................... 31
3.8 Battery Temperature Sensor ........................................................................................................................................ 31

4 Maintenance ................................................................................................................................. 32
4.1 Routine Maintenance .................................................................................................................................................. 32
4.2 Rectifying Common Faults ......................................................................................................................................... 33
4.2.1 AC Failure................................................................................................................................................................ 33
4.2.2 AC Over Volt ........................................................................................................................................................... 33
4.2.3 AC Under Volt ......................................................................................................................................................... 34
4.2.4 DC Over Volt ........................................................................................................................................................... 34
4.2.5 DC Under Volt ......................................................................................................................................................... 34
4.2.6 Batt Chg. Overcur. ................................................................................................................................................... 35
4.2.7 LLVD Disconnected ................................................................................................................................................ 35

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. iv

 TP48200A-DX12A1 Telecom Power
User Manual Contents

4.2.8 BLVD Disconnected ................................................................................................................................................ 35

4.2.9 Batt Loop Trip.......................................................................................................................................................... 36
4.2.10 Batt. High Temp. .................................................................................................................................................... 36
4.2.11 Batt. Low Temp...................................................................................................................................................... 36
4.2.12 Door Alarm ............................................................................................................................................................ 37
4.2.13 Rectifier Missing ................................................................................................................................................... 37
4.2.14 Single Rect Fault.................................................................................................................................................... 38
4.2.15 Multi-Rect. Fault.................................................................................................................................................... 38
4.2.16 Rect Fault ............................................................................................................................................................... 38
4.2.17 Rect Protection....................................................................................................................................................... 38
4.2.18 Rect Comm Fault ................................................................................................................................................... 39
4.2.19 DC SPD Fault ........................................................................................................................................................ 39
4.2.20 Batt Test Negative .................................................................................................................................................. 39
4.3 Identifying Component Faults .................................................................................................................................... 40
4.3.1 Identifying Circuit Breaker Faults ........................................................................................................................... 40
4.3.2 Identifying Rectifier Faults ...................................................................................................................................... 40
4.3.3 Identifying SMU Faults ........................................................................................................................................... 40
4.4 Replacing Components ............................................................................................................................................... 40
4.4.1 Replacing a Rectifier ............................................................................................................................................... 41
4.4.2 Replacing a Circuit Breaker ..................................................................................................................................... 42
4.4.3 Replacing a Plug-in Circuit Breaker ........................................................................................................................ 43
4.4.4 Replacing the PCB of UIM02C ............................................................................................................................... 44
4.4.5 Replacing an SMU ................................................................................................................................................... 46
4.4.6 Replacing an AC SPD Module ................................................................................................................................ 47
4.4.7 Replacing a Direct Ventilation Fan .......................................................................................................................... 48
4.4.8 Replacing an Air Filter ............................................................................................................................................. 49
4.4.9 Replacing a Heater ................................................................................................................................................... 50
4.4.10 Replacing a Battery Temperature Sensor ............................................................................................................... 51
4.4.11 Replacing a Door Status Sensor ............................................................................................................................. 53

A Technical Specifications ........................................................................................................... 54

A.1 Environment Specifications ....................................................................................................................................... 54
A.2 Electrical Specifications............................................................................................................................................. 54
A.3 EMC Specifications ................................................................................................................................................... 56
A.4 Cabinet Specifications ............................................................................................................................................... 56
A.5 Heater Specifications ................................................................................................................................................. 57

B Electrical Conceptual Diagrams .............................................................................................. 58

C Associations Between Alarms and Dry Contacts on the UIM ........................................... 59
D Acronyms and Abbreviations.................................................................................................. 61

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. v

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

1 Safety Precautions

1.1 General Safety

Statement
Before installing, operating, and maintaining the equipment, read this document and observe
all the safety instructions on the equipment and in this document.
The "NOTICE", "CAUTION", "WARNING", and "DANGER" statements in this document
do not cover all the safety instructions. They are only supplements to the safety instructions.
Huawei will not be liable for any consequence caused by the violation of general safety
requirements or design, production, and usage safety standards.
Ensure that the equipment is used in environments that meet its design specifications.
Otherwise, the equipment may become faulty, and the resulting equipment malfunction,
component damage, personal injuries, or property damage are not covered under the warranty.
Follow local laws and regulations when installing, operating, or maintaining the equipment.
The safety instructions in this document are only supplements to local laws and regulations.
Huawei will not be liable for any consequences of the following circumstances:
 Operation beyond the conditions specified in this document
 Installation or use in environments which are not specified in relevant international or
national standards
 Unauthorized modifications to the product or software code or removal of the product
 Failure to follow the operation instructions and safety precautions on the product and in
this document
 Equipment damage due to force majeure, such as earthquakes, fire, and storms
 Damage caused during transportation by the customer
 Storage conditions that do not meet the requirements specified in this document

General Requirements
 Before installing, operating, or maintaining the equipment, remove any conductive
objects such as watches or metal jewelry like bracelets, bangles, and rings to avoid
electric shock.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 1

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 When installing, operating, or maintaining the equipment, wear dedicated protective

gears such as insulation gloves, goggles, and safety clothing, helmet, and shoes, as
shown in the following figure.

 Use insulated tools or tools with insulated handles, as shown in the following figure.

 Follow the specified procedures for installation, operation, and maintenance.

 Ensure that bolts are tightened with a torque wrench and marked using red or blue color.
Installation personnel mark tightened bolts in blue. Quality inspection personnel confirm
if the bolts are tightened and then mark them in red. (The marks should cross the edges
of the bolts, as shown in the following figure.)

 Before installing, operating, or maintaining a cabinet, clean up any water, ice, snow, or
other sundries on the top of the cabinet to prevent sundries from falling into the cabinet
when you open the cabinet door.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 2

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Do not install, use, or operate outdoor equipment and cables (including but not limited to
moving equipment, operating equipment and cables, inserting connectors to or removing
connectors from signal ports connected to outdoor facilities, working at heights, and
performing outdoor installation) in harsh weather conditions such as lightning, rain,
snow, and level 6 or stronger wind.
 Before handling a conductor surface or terminal, measure the contact point voltage and
ensure that there is no risk of electric shock.
 Ensure that all slots are installed with boards or filler panels. Avoid hazards caused by
hazardous voltages or energy on boards. Ensure that the air channel is normal, control
electromagnetic interference, and prevent dust and other sundries on the backplane,
baseplate, and boards.
 After installing the equipment, remove idle packing materials such as cartons, foam,
plastics, and cable ties from the equipment area.
 In the case of a fire, immediately leave the building or the equipment area, and turn on
the fire alarm bell or make an emergency call. Do not enter the building on fire in any
case.
 Do not stop using protective devices. Pay attention to the warnings, cautions, and related
precautionary measures in this document and on the equipment. Promptly replace
warning labels that have worn out.
 Keep irrelevant people away from the equipment. Only operators are allowed to access
the equipment.
 All cable holes should be sealed. Seal the used cable holes with firestop putty. Seal the
unused cable holes with the caps delivered with the cabinet. The following figure shows
the criteria for correct sealing with firestop putty.

 Do not use water, alcohol, oil, or other solvents to clean electrical components inside and
outside a cabinet.

Personal Safety
 If there is a probability of personal injury or equipment damage during operations on the
equipment, immediately stop the operations, report the case to the supervisor, and take
feasible protective measures.
 To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to
telecommunication network voltage (TNV) circuits.
 Do not power on the equipment before it is installed or confirmed by professionals.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 3

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

Symbol Conventions
To ensure personal and equipment safety, observe all the safety instructions marked on the
equipment when installing, operating, and maintaining the equipment.

Symbol Description
Indicates a part exposed to high voltage. This symbol warns
operators that both direct and indirect contact with the power grid
is fatal. Such areas include hazardous voltage points or protective
power supply covers that may be removed during maintenance.
Warns users of overheating. This symbol is attached to a device
surface that may overheat and cause scalding. It warns users not to
touch the surface during operations or maintenance. Users should
wear heat insulation gloves before operations to prevent scalding.
Indicates protection earthing. This symbol is attached next to a
or protection ground terminal next to grounded equipment and an
external ground system. An equipment ground cable is connected
to an external ground bar through the protection ground terminal.
Indicates equipotential bonding. This symbol is found with
equipotential terminals inside equipment.

Indicates electrostatic discharge (ESD). This symbol is used in all

electrostatic sensitive areas. Before operating equipment in these
areas, wear ESD gloves or an ESD wrist strap.
Indicates that the equipment is safe to use at altitudes below 2000
m (6561.6 ft.).

Indicates that the equipment is not safe to use in tropical climates.

Indicates a fan assembly or moving part. This symbol is

silkscreened on or attached to the panel of a fan assembly,
or warning operators to keep away. Do not touch the blades when the
fan is rotating.

Indicates that users should refer to the instruction. This symbol is

used when the usage of a device port cannot be clearly described.
or For example, this symbol can be used in but not limited to the
following scenarios:
1. For a multi-power device, use it near the power supply to
replace the multi-power supply identifier. The symbol indicates
that the device has multiple power inputs. Therefore, when
powering off the device, you must disconnect all power inputs.
2. If there are multiple output ports, use the symbol near the
or
output ports. Connect cables according to the rated power
output and configuration parameter information in the
instruction.
3. If there are multiple slots, use the symbol near the slot

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 4

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

Symbol Description
information. For details, see the description of slot information,
restrictions on boards, and usage conditions in the instruction.

1.2 Personnel Requirements

 Personnel who plan to install or maintain Huawei equipment must receive thorough
training, understand all necessary safety precautions, and be able to correctly perform all
operations.
 Only qualified professionals or trained personnel are allowed to install, operate, and
maintain the equipment.
 Only qualified professionals are allowed to remove safety facilities and inspect the
equipment.
 Personnel who will operate the equipment, including operators, trained personnel, and
professionals, should possess the local national required qualifications in special
operations such as high-voltage operations, working at heights, and operations of special
equipment.

 Professionals: personnel who are trained or experienced in equipment operations and are clear of the
sources and degree of various potential hazards in equipment installation, operation, and
maintenance
 Trained personnel: personnel who are technically trained, have required experience, are aware of
possible hazards on themselves in certain operations, and are able to take protective measures to
minimize the hazards on themselves and other people
 Operators: operation personnel who may come in contact with the equipment, except trained
personnel and professionals

1.3 Electrical Safety

Grounding
 The protective ground of the equipment should be reliably connected to the ground
screw on the metal enclosure (grounding resistance ≤ 0.1 ohm).
 For the equipment that needs to be grounded, install the ground cable first when
installing the equipment and remove the ground cable last when removing the
equipment.
 Do not damage the ground conductor.
 Do not operate the equipment in the absence of a properly installed ground conductor.
 For the equipment that uses a three-pin socket, ensure that the ground terminal in the
socket is connected to the protection ground.

AC and DC Power

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 5

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 The power system is energized by power sources with hazardous voltage. Direct or
indirect contact (through damp objects) with the power sources may result in electric
shock.
 Non-standard and improper operations may result in fire or electric shock.
 Do not connect or disconnect power cables with power on. Transient contact between the
core of the power cable and the conductor will generate electric arcs or sparks, which may
cause fire or personal injury.
 If the power supply to the equipment is permanently connected, install an easily
accessible disconnector at the exterior of the device.
 Before making electrical connections, switch off the disconnector on the upstream device
to cut off the power supply if people may contact energized components.
 If a "high electricity leakage" tag is attached on the equipment, ground the protective
ground terminal on the equipment enclosure before connecting the AC power supply;
otherwise, electric shock as a result of electricity leakage may occur.
 Before installing or removing a power cable, turn off the power switch.
 Before connecting a power cable, check that the label on the power cable is correct.
 Before connecting the power supply, ensure that cable connections are correct.
 If the equipment has multiple inputs, disconnect all the inputs before operating the
equipment.

Cabling
 When routing cables, ensure that a distance of at least 30 mm exists between the cables
and heat-generating components or areas. This prevents damage to the insulation layer of
the cables.
 Do not route cables behind the air intake and exhaust vents of the equipment.
 Ensure that cables meet the VW-1 flame spread rating requirements.
 Bind cables of the same type together. When routing cables of different types, ensure that
they are at least 30 mm away from each other.
 Ensure that all cables are securely bound. Route and bind cables so that they appear neat
and tidy and their cable sheaths are intact.
 If an AC input power cable is connected to the cabinet from the top, bend the cable in a
U shape outside the cabinet and then route it into the cabinet.
 Ensure that the bending radius of each cable is at least five times the diameter of the
cable.
 When routing power cables, ensure that there is no coiling or twisting. Do not join or
weld power cables. If necessary, use a longer cable.

ESD
 When installing, operating, and maintaining the equipment, comply with the ESD
protection regulations and wear the ESD clothing, gloves, and wrist strap.
 When holding a board, hold its edge without touching any components. Do not touch the
components with your bare hands.
 Package boards with ESD packaging materials before storing or transporting them.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 6

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

1.4 Installation Environment Requirements

 To prevent fire due to high temperature, ensure that the ventilation vents or heat
dissipation system are not blocked when the equipment is running.
 Ensure that there are no acid, alkaline, or other corrosive gases in the installation place.
 Do not place the equipment near heat sources or exposed fire sources, such as electric
heaters, microwave ovens, roasters, water heaters, furnace fire, candles, or other places
where high temperature may occur. Otherwise, the enclosure will melt or the equipment
will heat up, which can cause a fire.
 Install the equipment in an area far away from liquids. Do not install it under areas prone
to condensation, such as under water pipes and air exhaust vents, or areas prone to water
leakage, such as air conditioner vents, ventilation vents, or feeder windows of the
equipment room. Ensure that no liquid enters the equipment to prevent faults or short
circuits.
 Before installing the equipment into a cabinet, ensure that the cabinet is secured and will
not tilt or fall down due to loss of balance, which can cause personal injury or equipment
damage.
 Do not expose the equipment to flammable or explosive gas or smoke. Do not perform
any operation on the equipment in such environments.

Installation at Heights
Working at heights refers to operations that are performed at least 2 meters above the ground.
Do not at heights in any of the following situations:
 Rainwater remains on steel pipes or other risky conditions exist. After the preceding
conditions no longer exist, the safety director and relevant technical personnel need to
check the involved equipment. Operators can begin working only after obtaining
consent.
 When working at heights, comply with local relevant laws and regulations.
 Only trained and qualified personnel are allowed to work at heights.
 Before working at heights, check the climbing tools and safety gears such as safety
helmets, safety belts, ladders, springboards, scaffolding, and lifting equipment. If they do
not meet the requirements, take corrective measures or disallow working at heights.
 Wear personal protective equipment such as the safety helmet and safety belt or waist
rope and fasten it to a solid structure. Do not mount it on an insecure moveable object or
metal object with sharp edges. Make sure that the hooks will not slide off.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 7

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Set a restricted area and eye-catching signs for working at heights to warn away irrelevant
personnel.
 Carry the operation machinery and tools properly to prevent them from falling off and
causing injuries.
 Personnel involving working at heights are not allowed to throw objects from the height to
the ground, or vice versa. Objects should be transported by tough slings, hanging baskets,
highline trolleys, or cranes.
 Do not perform operations on the upper and lower layers at the same time. If unavoidable,
install a dedicated protective shelter between the upper and lower layers or take other
protective measures. Do not pile up tools or materials on the upper layer.
 Ensure that guard rails and warning signs are set at the edges and openings of the area
involving working at heights to prevent falls.
 Do not pile up scaffolding, springboards, or other sundries on the ground under the area
involving working at heights. Do not allow people to stay or pass under the area involving
working at heights.
 Inspect the scaffolding, springboards, and workbenches used for working at heights in
advance to ensure that their structures are solid and not overloaded.
 Dismantle the scaffolding from top down after finishing the job. Do not dismantle the
upper and lower layers at the same time. When removing a part, ensure that other parts
will not collapse.
 Do not loiter when working at heights. Do not sleep at heights.
 Any violations must be promptly pointed out by the site manager or safety supervisor
and the involved personnel should be prompted for correction. Personnel who fail to stop
violations will be forbidden from working.
 Operators who violate the safety regulations are responsible for accidents caused. The
supervisor has to bear the responsibility accordingly.

1.5 Mechanical Safety

Hoisting Devices

Do not walk under hoisted objects.

 Only trained and qualified personnel should perform hoisting operations.
 Check that hoisting tools are available and in good condition.
 Before hoisting objects, ensure that hoisting tools are firmly secured onto a load-bearing
object or wall.
 Ensure that the angle formed by two hoisting cables is no more than 90 degrees, as
shown in the following figure.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 8

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Do not drag steel ropes and hoisting tools or bump hoisted objects against hard objects
during hoisting.

Using Ladders
 Use wooden or fiberglass ladders when you need to perform live working at heights.
 When a step ladder is used, ensure that the pull ropes are secured and the ladder is held
firm.
 Before using a ladder, check that it is intact and confirm its load bearing capacity. Do not
overload it.
 Ensure that the wider end of the ladder is at the bottom, or protective measures have
been taken at the bottom to prevent the ladder from sliding.
 Ensure that the ladder is securely positioned. The recommended angle for a ladder
against the floor is 75 degrees, as shown in the following figure. An angle rule can be
used to measure the angle.

When climbing a ladder, take the following precautions to reduce risks and ensure safety:

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 9

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Keep your body steady.

 Do not climb higher than the fourth rung of the ladder from the top.
 To climb onto a roof, ensure that the ladder top is at least one meter higher than the roof
line, as shown in the following figure.

 Ensure that your body's center of gravity does not shift outside the legs of the ladder.

Drilling Holes
When drilling holes into a wall or floor, observe the following safety precautions:

Do not drill holes into the equipment. Doing so may affect the electromagnetic shielding of
the equipment and damage components or cables inside. Metal shavings from drilling may
short-circuit boards inside the equipment.
 Wear goggles and protective gloves when drilling holes.
 When drilling holes, protect the equipment from shavings. After drilling, clean up any
shavings that have accumulated inside or outside the equipment.

Moving Heavy Objects

 Be cautious to avoid injury when moving heavy objects.

 When moving the equipment by hand, wear protective gloves to prevent injuries.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 10

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Move or lift the equipment by holding its handles or lower edges. Do not hold the
handles of modules (such as power supply units, fans, and boards) that are installed in
the equipment because they cannot support the weight of the equipment.

1.6 Battery Safety

If no battery is involved, skip this section.
Before installing, operating, or maintaining batteries, read the battery manufacturer's
instructions. The safety precautions specified in this document are highly important
precautions that require special attention. For additional safety precautions, see the
instructions provided by the battery manufacturer.

Basic Requirements
Before operating batteries, carefully read the safety precautions for battery handling and
master the correct battery connection methods.

 Do not expose batteries at high temperatures or around heat-generating devices, such as

sunlight, fire sources, transformers, and heaters. Excessive heat exposure may cause the
batteries to explode.
 Do not burn batteries. Otherwise, the batteries may explode.
 To avoid leakage, overheating, fire, or explosions, do not disassemble, alter, or damage
batteries, for example, insert sundries into batteries or immerse batteries in water or other
liquids.
 When replacing a battery, use a battery of the same model or type. Improper replacement
may cause the battery to explode.
 Do not connect a metal conductor to the battery poles or touch the battery terminals.
Otherwise, the battery may be short-circuited and heat up, which can cause injuries such as
burning.

To ensure safety during battery installation, operation, and maintenance, pay attention to the
following:
 Do not wear conductive articles such as watches, bracelets, bangles, and rings.
 Wear goggles, rubber gloves, and protective clothing to prevent skin contact with
electrolyte in the case of electrolyte overflow. If a battery leaks, protect the skin or eyes
from the leaking liquid. If the skin or eyes come in contact with the leaking liquid, wash
it immediately with clean water and go to the hospital for medical treatment.
 Use dedicated insulated tools.
 Move batteries in the required direction. Do not place a battery upside down or tilt it.
 Keep the battery loop disconnected during installation and maintenance.
 Do not drop, squeeze, or puncture a battery. Protect batteries from external high pressure
to prevent internal short circuits and overheating.
 Dispose of waste batteries in accordance with local laws and regulations. Do not dispose
of batteries as household waste. If a battery is disposed of improperly, it may explode.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 11

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Do not use a damaged battery.

 To prevent injuries or explosion, do not allow children or pets to swallow or bite a
battery.
 If batteries experience discoloration, deformation, abnormal heating, or other
abnormalities during working, charging, or storage, stop using the batteries and replace
them with new ones.
 Batteries can work properly with the allowed charge and discharge parameters when the
temperature is within the specified range. If the temperature is outside the specified
range, the battery charge and discharge performance and safety are affected.

Battery Installation
Before installing batteries, observe the following safety precautions:
 Install batteries in a dry and cool environment with good ventilation, which is away from
high temperature and flammable materials, and take precautions against fire.
 Place and secure batteries horizontally.
 Note the polarities when installing batteries. Do not short-circuit the positive and
negative poles of the same battery or battery string. Otherwise, the battery may be
short-circuited.
 When installing a battery string, retain at least one breakpoint to prevent a loop being
formed. After checking that the installation is correct, close the breakpoints to finish the
installation.
 During the installation, insulate the terminals of cables connecting batteries. Ensure that
the terminals do not come into contact with metal components such as the cabinet.
 Secure battery cables or copper bars by tightening bolts to the required torque. Loose
connections will result in excessive voltage drop or cause batteries to burn out in the case
of excessive current.
 Check battery connections periodically, ensuring that all bolts are securely tightened.

Battery Short Circuit

Battery short circuits can generate high instantaneous current and release a great amount of
energy, which may cause equipment damage or personal injury.
 If permitted, disconnect the batteries in use before performing any other operations.
 To avoid battery short-circuit, do not maintain batteries with power on.

Flammable Gas

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 12

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 Do not use unsealed lead-acid batteries.

 To prevent fire or corrosion, ensure that flammable gas (such as hydrogen) is properly
exhausted for lead-acid batteries.

Lead-acid batteries emit flammable gas when used. Ensure that batteries are kept in a
well-ventilated area and take preventive measures against fire.

Battery Leakage

Battery overheating causes deformation, damage, and electrolyte spillage.

If the battery temperature exceeds 60°C, check for and promptly handle any leakage.
Electrolyte overflow may damage the equipment. It will corrode metal parts and boards, and
ultimately damage the boards.

When the electrolyte overflows, absorb and neutralize the electrolyte immediately. When
moving or handling a battery whose electrolyte leaks, note that the leaking electrolyte may
hurt human bodies.

If the electrolyte overflows, follow the instructions of the battery manufacturer or neutralize
the electrolyte by using sodium bicarbonate (NaHCO3) or sodium carbonate (Na2CO3).

Lithium Battery
The safety precautions for lithium batteries are similar to those for lead-acid batteries except
that you also need to note the precautions described in this section.

There is a risk of explosion if a battery is replaced with an incorrect model.

 A battery can be replaced only with a battery of the same or similar model recommended
by the manufacturer.
 When handling a lithium battery, do not place it upside down, tilt it, or bump it with
other objects.
 Keep the lithium battery loop disconnected during installation and maintenance.
 When the ambient temperature is lower than the lower limit of the operating temperature
(charge is forbidden at 0°C), do not charge the battery. Otherwise, a short circuit would
occur inside the battery.
 Do not throw a lithium battery in fire.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 13

TP48200A-DX12A1 Telecom Power
User Manual 1 Safety Precautions

 When maintenance is complete, return the waste lithium battery to the maintenance
office.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 14

TP48200A-DX12A1 Telecom Power
User Manual 2 Overview

2 Overview

2.1 Introduction
The TP48200A-DX12A1 (DC2) is an integrated telecom power system that supplies power to
and backs up power for –48 V DC outdoor communications equipment. It also provides space
for installing the equipment.

Figure 2-1 TP48200A-DX12A1 (DC2) exterior

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 15

 TP48200A-DX12A1 Telecom Power
User Manual 2 Overview

2.2 Features
 Wide input voltage range of 85 V AC to 300 V AC
 Comprehensive battery management
 Comprehensive DC surge protective design
 One fast Ethernet (FE) port and one RS485/RS232 port for network connections
 SNMP and HTTPS for communicating with HUAWEI Network Ecosystem (NetEco) and
third-party network management systems (NMSs), which ensures remote management
and unattended operation
 Liquid crystal display (LCD) for display and buttons for user operations
 Web user interface (WebUI) for user operations
 Multiple display languages, such as English, Chinese, Italian, French, Spanish,
Portuguese, Russian, German, and Turkish
 Hot-swappable rectifiers and site monitoring unit (SMU)
 Rectifier power factor (PF) of 0.99

2.3 System Configurations

Table 2-1 Power cabinet configurations

Item TP48200A-DX12A1 (DC2)

Input system 220/380 V AC three-phase; dual inputs: AC input and emergency
AC input
Surge protection Type 1+Type 2
System capacity 8.5 kW + backup
Rectifier A maximum of four R4850G2s
Battery (optional) One 150 Ah lead-acid battery string
Space for customer equipment ≥8U
Application environment Class B
Cooling Free cooling
Site monitoring unit (SMU) SMU02B
User interface module (UIM) UIM02C
Sensor Battery temperature sensor, door status sensor
Heater A maximum of two 500 W heaters:
 Standard: One 500 W heater
 Optional: One 500 W heater

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 16

TP48200A-DX12A1 Telecom Power
User Manual 2 Overview

 Class A environments refer to indoor environments where temperature and humidity are controllable,
including rooms where human beings live.
 Class B environments refer to indoor environments in which the ambient temperature and humidity
are not controlled and outdoor environments (with simple shielding measures) where the humidity
can reach 100%.
 Class C environments refer to sea environments or outdoor land environments (with simple
shielding measures) near pollution sources. If a site is near a pollution source, it is at most 3.7 km
away from salt water, such as the sea and salt lakes, 3 km away from heavy pollution sources, such
as smelteries, coal mines, and thermal power plants, 2 km away from medium pollution sources,
such as chemical, rubber, and galvanization industries, or 1 km away from light pollution sources,
such as packing houses, tanneries, and boiler rooms.
 Class D environments refer to areas about 500 m away from the seashore. Class D environments are
special Class C environments.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 17

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

3 Components

3.1 Interior
Figure 3-1 TP48200A-DX12A1 (DC2)interior

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 18

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

(1) RTN+ busbar (2) AC output (3) AC input unit

unit
(4) Cabinet ground bar (5) Heater (6) Heater (standard)
(optional)
(7) Air filter (8) Folder (9) Direct ventilation
fan
(10) Battery low voltage disconnection (11) Power
(BLVD) output box subrack

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 19

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Figure 3-2 Power subrack on TP48200A-DX12A1 (DC2)

(1) SMU02B (2) Space for NIM01C (3) Space for rectifiers
(4) UIM02C (5) Battery circuit breaker (6) Battery switch
(behind the cover)
(7) BLVD circuit (8) Load low voltage disconnection (9) RTN+ busbar
breakers (LLVD) circuit breakers
(10) AC input (11) AC surge protective device (SPD)
transfer switch

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 20

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Figure 3-3 AC box without cover on TP48200A-DX12A1 (DC2)

(1) German standard maintenance (2) AC light power (3) AC input circuit breaker
socket and protective circuit terminals and time and terminals
breaker relay
(4) PE terminal (5) AC output circuit (6) Emergency AC input
breaker and terminal circuit breaker and
terminals

Figure 3-4 DC output box on TP48200A-DX12A1 (DC2)

(1) BLVD circuit breakers

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 21

 TP48200A-DX12A1 Telecom Power
User Manual 3 Components

3.2 Power Distribution Unit

Table 3-1 Power distribution specifications

Item TP48200A-DX12A1 (DC2)

Input system 220/380 V AC three-phase

AC power distribution  AC input: two 3-pole 40 A circuit breakers, with a knob-type dual
power switch
 AC output: one German standard socket (with a 10 A RCD), one
1-pole 10 A circuit breaker, and AC light power terminals and one
time relay (5 A resistive load or 1 A capacitive load)
DC power distribution  BLVD circuit breakers: 2x32 A/1P, 2x20 A/1P, 2x16 A/1P, 2x10
A/1P, 2x6 A/1P
 LLVD circuit breakers: 3x63 A/1P
Battery route One 2-pole 125 A circuit breaker

3.3 Rectifier
Rectifiers convert AC input into stable DC output.

Figure 3-5 Rectifier

(1) Run indicator (2) Alarm indicator (3) Fault indicator

(4) Locking latch (5) Handle

Table 3-2 Rectifier indicator description

Indicator Color Status Description

Run indicator Green Steady on The rectifier has an AC power input.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 22

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Indicator Color Status Description

Off The rectifier has no AC power input.
The rectifier is faulty.
Blinking at 0.5 Hz The rectifier is being queried.
Blinking at 4 Hz The rectifier is loading an application program.
Alarm indicator Yellow Off No alarm has been generated.
Steady on  The rectifier has generated an alarm due to
ambient overtemperature.
 The rectifier has generated an alarm for
shutdown due to ambient overtemperature or
undertemperature.
The rectifier is protecting itself against AC input
overvoltage or undervoltage.
The rectifier is hibernating.
Blinking at 0.5 Hz The communication between the rectifier and the
SMU has been interrupted.
Fault indicator Red Off The rectifier is running properly.
Steady on The rectifier has been locked out due to output
overvoltage.
The rectifier has no output due to an internal fault.

3.4 SMU02B
Panel

Figure 3-6 SMU02B panel

(1) Run (2) Minor alarm indicator (3) Major alarm

indicator indicator

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 23

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

(4) Buttons (5) USB port (protected by a security (6) RS485/RS232 port
mechanism)
(7) Handle (8) Locking latch (9) Fast Ethernet (FE)
port
(10) LCD

Indicators

Table 3-3 Indicator description

Name Color Status Description

Run indicator Green Off The SMU is faulty or has no DC input.

Blinking The SMU is running properly and
slowly (0.5 communicating with the host properly.
Hz)
Blinking fast The SMU is running properly but fails to
(4 Hz) communicate with the host properly.
Minor alarm Yellow Off No minor or warning alarm is generated.
indicator
Steady on A minor or warning alarm is generated.
Major alarm Red Off No critical or major alarm is generated.
indicator
Steady on A critical or major alarm is generated.

Buttons

Table 3-4 Button description

Button Name Description

Up Press Up and Down to scroll through the menus or to change the
value of a parameter.
Down

Cancel Returns to the previous menu without saving the settings.

Enter  Enters the main menu from the standby screen.

 Enters a submenu from the main menu.
 Saves menu settings on a submenu.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 24

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Button Name Description

NOTE
 The LCD screen becomes dark if no button is pressed within 30 seconds.

 You need to log in again if no button is pressed within 1 minute.

 To increase or decrease a parameter value quickly, hold down or .

 To restart the SMU, hold down and for 10 seconds.

 To increase (or decrease) the LCD contrast ratio, hold down and (or ) for 2
seconds.

USB Ports
You can quickly deploy a site, import and export configuration files, export running logs, and
upgrade software by inserting the USB flash drive that is specially used for site deployment
into the USB port.
After installing the specific WiFi module using the USB port, you can access the WebUI
locally, which facilitates operations.

Using WiFi modules provided by another vendor may cause data loss or function exception.
Consequences arising from this will not be borne by Huawei.

Communications Ports

Table 3-5 Communication port description

Communications Port Communications Communications Protocol

Parameter

FE 10/100M autonegotiation HTTPS, NetEco protocol, SNMP

and TCP-Modbus protocol
RS485/RS232 Baud rate: 1200bit/s, Master/slave protocol, YDN
2400bit/s, 4800bit/s, protocol, and Modbus protocol
9600bit/s, 14400bit/s,
19200bit/s, 115200bit/s

NOTE
All these ports are protected by a security mechanism.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 25

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Figure 3-7 FE/RS485/RS232 port pins

Table 3-6 Pin definitions for the FE port

Pin Signal Description

1 TX+ Transmits data over FE.
2 TX-
3 RX+ Receives data over FE.
6 RX-
4, 5, 7, 8 NA -

Table 3-7 Pin definitions for the RS485/RS232 port

Pin Signal Description

1 TX+ Transmits data over RS485.

2 TX-
4 RX+ Receives data over RS485.
5 RX-
3 RX232 Receives data over RS232.
7 TX232 Transmits data over RS232.
6 PGND Connects to the ground.
8 NA –

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 26

 TP48200A-DX12A1 Telecom Power
User Manual 3 Components

3.5 User Interface Module UIM02C

Panel
The user interface module UIM02C supports eight dry contact outputs, six dry contact inputs,
and seven sensor ports. The sensor ports include one ambient temperature and humidity input,
one water sensor input, two ambient temperature inputs, one door status sensor input, one
smoke sensor input, and one battery temperature input.

Figure 3-8 UIM02C panel

Ports

Table 3-8 UIM02C ports

Port Type Silk Screen Description

Sensor ports TEM-HUM Ambient temperature and humidity sensor
WATER Water sensor
TEMP1 Ambient temperature sensor 1
TEMP2 Ambient temperature sensor 2
GATE Door status sensor
SMOKE Smoke sensor
BTEMP Battery temperature sensor
Dry contact input ports DIN1 NOTE
For the associations between the dry contact input ports and
DIN2 alarms, see the appendix.

DIN3
DIN4
DIN5
DIN6
Dry contact output ports ALM1 NOTE
For the associations between the dry contact output ports and
ALM2 alarms, see the appendix.

ALM3
ALM4

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 27

 TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Port Type Silk Screen Description

ALM5
ALM6
ALM7
ALM8
Communications port COM RS485 port

Communications Port

Table 3-9 COM communications port description

Communications Port Communications Communications Function

Parameter Protocol

COM port Baud rate: 9600 bit/s, 19,200 Master/slave protocols Connects to a
bit/s, 115,200 bit/s and Modbus lower-level device
such as the battery
voltage detector or
intelligent air
conditioner.

NOTE
The COM port is protected by a security mechanism.

Figure 3-9 Pins in the COM port

Table 3-10 Pin definitions for the COM port

Pin Signal Description

1 RX+ Receives data over RS485.

2 RX-
4 TX+ Sends data over RS485.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 28

 TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Pin Signal Description

5 TX-
6 PGND Protective grounding.
3, 7, and 8 Reserved N/A

Pins

Figure 3-10 UIM02C pin numbers

Table 3-11 UIM02C pin definitions

Silk Screen No. Pin Definition

TEM-HUM 1 12 V
2 ENV_TEMP
3 12 V
4 ENV_HUM
WATER 1 12 V
2 WATER
3 GND
4 Not defined
TEMP1 1 GND
2 TEMP1
TEMP2 1 GND
2 TEMP2

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 29

 TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Silk Screen No. Pin Definition

GATE 1 GATE+
2 GATE-
SMOKE 1 SMOKE
2 12 V
BTEMP 1 GND
2 BTEMP

3.6 (Optional) Heater

A heater assembly unit (HAU) is adopted to ensure a proper operating temperature for the
equipment inside the cabinet.

Figure 3-11 Heater

(1) Indicator (2) Alarm dry contact (3) Control dry contact
(4) AC input port

Table 3-12 Indicator description

Silk Color Status Description

Screen

RUN Green Steady on The heater is powered on and takes a self-test.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 30

TP48200A-DX12A1 Telecom Power
User Manual 3 Components

Silk Color Status Description

Screen

Off The heater is not powered on.

ALM Red Off No alarm is generated.
Steady on An alarm is generated and the heater needs to be replaced.

3.7 Door Status Sensor

Figure 3-12 Door status sensor

(1) Switch (2) Magnet

3.8 Battery Temperature Sensor

Figure 3-13 Battery temperature sensor

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 31

 TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

4 Maintenance

4.1 Routine Maintenance

Perform routine maintenance periodically based on site requirements. The recommended
interval is six months. If any fault occurs, rectify it in a timely manner.

Table 4-1 Routine maintenance checklist

Maintenance Check Item Check Method Repair When Measure

Item

Door lock The door lock is By observation or The door lock is Replace the
damaged. by locking and damaged. door lock.
unlocking the door
Fan Dust accumulates on By observation Thick dust accumulates Clean the dust.
the fan. on the fan.
The fan is intact, and By observing or The fan is damaged, the Replace the
the rotation speed, listening to the fan vibration is abnormal, or fan.
noise, and vibration the noise is loud.
are in normal ranges.
TCUC control The TCUC control By observation or The TCUC control board Replace the
board board works properly. by checking the does not work properly. TCUC control
indicator and board.
alarms
Air filter Dust accumulates on By observation  The high temperature Replacing an
the dust filter. alarm is generated Air Filter
frequently, and the
temperature in the
cabinet is obviously
higher than the
ambient temperature.
 Dust accumulates on
the dust filter.
Electricity The output voltage is Multimeter The BLVD or LLVD For details, see
normal. voltage exceeds the 4.2 Rectifying
threshold. Common

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 32

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Maintenance Check Item Check Method Repair When Measure

Item
Preventive Indicators are normal. By observation An alarm is generated. Faults.
maintenance
Exterior The paint or By observation The cabinet is damaged Repaint and
electroplated coating or deformed. repair the
on the cabinet is intact. shell.
Grounding The ground point By observation or The cable that connects Secure the
properly connects to by using a the ground point and the ground point
the equipment room screwdriver or equipment room ground or replace the
ground bar. wrench bar is loose. ground cable.

4.2 Rectifying Common Faults

4.2.1 AC Failure
Possible Causes
 The AC input power cable is faulty.
 The AC input circuit breaker is OFF.
 The power grid is faulty.

Measures
1. Check whether the AC input cable is loose. If so, secure the AC input cable.
2. Check whether the AC input circuit breaker is OFF. If so, handle the fault which caused
the AC input circuit breaker to turn OFF and then switch on the circuit breaker.
3. Check whether the AC input voltage is lower than 50 V AC. If so, handle the power grid
fault.

4.2.2 AC Over Volt

Possible Causes
 The AC overvoltage alarm threshold is incorrectly set on the SMU.
 The power grid is faulty.

Measures
1. Check whether the AC overvoltage alarm threshold is correctly set. If not, set the
threshold to the correct value.
2. Check whether the AC input voltage exceeds the AC overvoltage alarm threshold (280 V
AC by default). If so, handle the AC input fault.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 33

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

4.2.3 AC Under Volt

Possible Causes
 The AC undervoltage alarm threshold is incorrectly set on the SMU.
 The power grid is faulty.

Measures
1. Check whether the AC undervoltage alarm threshold is correctly set. If not, set the
threshold to the correct value.
2. Check whether the AC input voltage is below the AC undervoltage alarm threshold (180
V AC by default). If so, handle the AC input fault.

4.2.4 DC Over Volt

Possible Causes
 The DC overvoltage alarm threshold is incorrectly set on the SMU.
 The power system voltage has been manually set to a very high value.
 Rectifiers are faulty.

Measures
1. Check whether the DC overvoltage alarm threshold (58 V DC by default) is correctly set.
If not, set the threshold to the correct value.
2. Check whether the system voltage has been manually set to a very high value. If so,
check with other maintenance personnel whether the voltage can be changed to a normal
value.
3. Remove the rectifiers one by one and check whether the alarm is cleared. If the alarm
still exists, reinstall the rectifier. If the alarm is cleared, replace the rectifier.

4.2.5 DC Under Volt

Possible Causes
 An AC power failure occurs.
 The DC undervoltage alarm threshold is not set properly on the SMU.
 The system configuration is not proper.
 The power system voltage is set too low in manual mode.
 Rectifiers are faulty.

Measures
1. Check whether an AC power failure occurs. If yes, resume the AC power supply.
2. Check whether the DC undervoltage alarm threshold (46.8 V DC by default) is properly
set. If no, adjust it to a proper value.
3. Check whether the load current is greater than the current power system capacity. If yes,
expand the power system capacity or reduce the load power.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 34

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

4. Check whether the system voltage is set too low in manual mode. If yes, confirm the
reason and adjust the voltage to a proper value after the operation.
5. Check whether the power system capacity is insufficient for the loads due to rectifier
failures. If yes, replace the faulty rectifier.

4.2.6 Batt Chg. Overcur.

Possible Causes
 Rectifier communication is interrupted.
 SMU connections are loose.
 The SMU is faulty.

Measures
1. Check whether an alarm has been generated for interrupted rectifier communication. If
so, remove the rectifier, reinstall it, and check whether the alarm is cleared. If the alarm
still exists, replace the rectifier.
2. Remove the SMU, reinstall it, and check whether the alarm is cleared. If the alarm still
exists, replace the SMU.

4.2.7 LLVD Disconnected

Possible Causes
 An AC power failure has occurred.
 Loads are manually disconnected.
 The load disconnection voltage has been set to a very high value on the SMU.

Measures
1. Check whether an AC power failure has occurred. If so, rectify the fault to restore the
AC power supply.
2. Check whether loads are manually disconnected. If so, check with other maintenance
personnel whether the loads can be reconnected.
3. Check whether the load disconnection voltage (44 V DC by default) has been set to a
very high value on the SMU. If so, adjust it to a normal value.

4.2.8 BLVD Disconnected

Possible Causes
 An AC power failure has occurred.
 Batteries are manually disconnected.
 The battery disconnection voltage has been set to a very high value on the SMU.

Measures
1. Check whether an AC power failure has occurred. If so, rectify the fault to restore the
AC power supply.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 35

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

2. Check whether batteries are manually disconnected. If so, check with other maintenance
personnel whether the batteries can be reconnected.
3. Check whether the battery disconnection voltage (43 V DC by default) has been set to a
very high value on the SMU. If so, adjust it to a normal value.

4.2.9 Batt Loop Trip

Possible Causes
 The battery circuit breaker or fuse detection cable is loosely connected.
 The battery circuit breaker has tripped or the battery fuse has blown.
 The contactor is faulty.

Measures
1. Check whether the battery circuit breaker or fuse detection cable is loosely connected. If
so, reconnect the cable.
2. Check whether the battery circuit breaker has tripped or the battery fuse has blown. If so,
rectify the battery loop fault and then switch on the circuit breaker or replace the fuse.
3. Manually switch on or switch off the battery contactor and check whether the battery
current changes accordingly. If not, replace the contactor.

4.2.10 Batt. High Temp.

This alarm is generated only for the power system that has a battery temperature sensor installed.

Possible Causes
 The high battery temperature alarm threshold is incorrectly set.
 The battery temperature control system is faulty.
 The battery temperature sensor is faulty.

Measures
1. Check whether the high battery temperature alarm threshold (50°C by default) is
correctly set. If not, set the threshold to the correct value.
2. Check whether the battery temperature control system is faulty. If so, rectify the fault.
The alarm is cleared when the battery temperature falls within the allowed range.
3. Check whether the battery temperature sensor is faulty. If so, replace the temperature
sensor.

4.2.11 Batt. Low Temp.

This alarm is generated only for the power system that has a battery temperature sensor installed.

Possible Causes
 The low battery temperature alarm threshold is incorrectly set on the SMU.
 The battery temperature control system is faulty.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 36

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

 The battery temperature sensor is faulty.

Measures
1. Check whether the low battery temperature alarm threshold (-10°C by default) is
correctly set. If not, set the threshold to the correct value.
2. Check whether the temperature control system for the battery compartment is faulty. If
so, rectify the fault. The alarm is cleared when the temperature in the battery
compartment becomes normal.
3. Check whether the battery temperature sensor is faulty. If so, replace the battery
temperature sensor.

4.2.12 Door Alarm

This alarm is generated only for the power system that has door status sensor installed.

Possible Causes
 The cabinet doors are open.
 The door status sensor is faulty.

Measures
1. Close cabinet doors.
2. Check whether the door status sensor is faulty. If yes, replace the door status sensor.

4.2.13 Rectifier Missing

Possible Causes
 Rectifiers are not powered on.
 Rectifiers are faulty.
 The subrack or slot connectors are faulty.
 The SMU is faulty.

Measures
1. Check whether rectifier circuit breakers are ON. If not, switch them on.
2. Check whether rectifiers are removed. If so, confirm the reason and reinstall them.
3. Replace faulty rectifiers.
4. Check whether rectifiers in the rectifier subrack do not work. If so, remove these
rectifiers and check whether their slot connectors are damaged. If the connectors are
damaged, repair or replace the slot connectors or the entire subrack.
5. If the alarm persists after the preceding measures are taken and the SMU is restarted,
replace the SMU.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 37

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

4.2.14 Single Rect Fault

Possible Causes
 The subrack or slot connector is faulty.
 A rectifier is faulty.
 The SMU is faulty.

Measures
1. Remove the rectifier and check whether the slot connector is damaged or deformed. If so,
repair or replace the slot connector or the entire subrack.
2. Reinstall the rectifier. If the alarm persists, replace the rectifier.
3. Restart the SMU. If the alarm persists, replace the SMU.

4.2.15 Multi-Rect. Fault

Possible Causes
 The subrack or slot connectors are faulty.
 Rectifiers are faulty.
 The SMU is faulty.

Measures
1. Remove the rectifiers and check whether the slot connectors are damaged or deformed. If
so, repair or replace the slot connectors or the entire subrack.
2. Reinstall the rectifiers. If the alarm persists, replace the rectifiers.
3. Restart the SMU. If the alarm persists, replace the SMU.

4.2.16 Rect Fault

Possible Causes
 Rectifier connections are loose.
 A rectifier is faulty.

Measures
1. Check the Fault indicator on the rectifier panel. If it is steady red, remove the rectifier,
and then reinstall it after the indicator turns off.
2. If the alarm persists, replace the rectifier.

4.2.17 Rect Protection

Possible Causes
 The rectifier input voltage is too high.
 The rectifier input voltage is too low.
 The ambient temperature is too high.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 38

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

 The rectifier is abnormal.

Measures
1. Check whether the AC input voltage exceeds the upper threshold for rectifier working
voltage. If so, locate and rectify the power supply fault and restore the power supply.
2. Check whether the AC input voltage is below the lower threshold for rectifier working
voltage. If so, locate and rectify the power supply fault and restore the power supply.
3. Check whether the ambient temperature is higher than the maximum operating
temperature of the rectifier. If so, locate and rectify the temperature control system fault.
4. Remove the rectifier that has generated the alarm and reinstall it after the indicator turns
off. If the alarm persists, replace the rectifier.

4.2.18 Rect Comm Fault

Possible Causes
 A rectifier has been removed.
 Rectifier connections are loose.
 A rectifier is faulty.

Measures
1. Check whether a rectifier has been removed. If so, reinstall it.
2. If the rectifier is in position, remove the rectifier and reinstall it.
3. If the alarm persists, replace the rectifier.

4.2.19 DC SPD Fault

Possible Causes
 The DC SPD detection cable is disconnected.
 The DC SPD is faulty.

Measures
1. Check whether the DC SPD detection cable is disconnected. If so, reconnect the cable.
2. If the DC SPD detection cable is reliably connected, replace the DC SPD.

4.2.20 Batt Test Negative

Possible Causes
The battery voltage drops to the test end voltage (46 V by default) within the test end time (15
minutes by default).

Measures
1. Check whether the battery is overloaded or aged.
2. Check whether the test end time and test end voltage are correctly set.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 39

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

If the battery test duration is less than 30 minutes, the battery test result is displayed as "NO RESULT".

4.3 Identifying Component Faults

4.3.1 Identifying Circuit Breaker Faults
The following indicate that the circuit breaker is faulty:
 The circuit breaker cannot be switched to ON/OFF after the short circuit fault for its end
circuit is rectified.
 When the circuit breaker is switched to ON and its input voltage is normal, the voltage
between the two ends of the circuit breaker exceeds 1 V.
 The input voltage is normal, but the resistance between both ends of the circuit breaker is
less than 1 kΩ when the circuit breaker is OFF.

4.3.2 Identifying Rectifier Faults

A rectifier is damaged if any of the following conditions is not met:
 When the rectifier does not communicate with the SMU and the AC input voltage is
around 220 V, the green indicator on the rectifier is steady on, the yellow indicator is
blinking, the red indicator is off, and the rectifier output is normal.
 The SMU can perform equalized charging, float charging, and current limiting control
for the rectifier when the communication cable to the rectifier is correctly connected and
communication is established between the rectifier and the SMU.

4.3.3 Identifying SMU Faults

The following indicate that the SMU is faulty:
 The DC output is normal but the green indicator on the SMU is off.
 The SMU breaks down or cannot be started. Its LCD has abnormal display or buttons
cannot be operated.
 With alarm reporting enabled, the SMU does not report alarms when the power system is
faulty.
 The SMU reports an alarm when the power system is not faulty.
 The SMU fails to communicate with the connected lower-level devices even though the
communications cables are correctly connected.
 Communication between the SMU and all rectifiers fails even though the rectifiers and
the communications cables are normal.
 The SMU cannot monitor AC or DC power distribution when communications cables are
intact and AC and DC power distribution is normal.
 Parameters cannot be set or running information cannot be viewed on the SMU.

4.4 Replacing Components

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 40

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

 Performing maintenance or replacing components may interrupt power to the loads if

battery reserve is insufficient. Ensure that the switches for primary loads are in the ON
position and do not turn off the battery switch and the AC input switch at the same time.
 Obtain prior written consent from the customer if load disconnection is required.
 Do not perform maintenance on rainy days. Otherwise, rain water can enter the system and
damage devices and components.

4.4.1 Replacing a Rectifier

Prerequisites
 Protective gloves and the cabinet door key are available.
 The new rectifier is intact.

To prevent burns, exercise caution when removing a rectifier because the rectifier may be hot
as a result of continuous operation.

Procedure
Step 1 Wear protective gloves.
Step 2 Push the locking latch on the right side of the panel towards the left.
Step 3 Gently draw the handle outwards, and then remove the rectifier from the subrack, as shown in
Figure 4-1.

Figure 4-1 Removing a rectifier

Step 4 Push the locking latch on the new rectifier towards the left, and pull out the handle.
Step 5 Place the new rectifier at the entry of the correct slot.
Step 6 Gently slide the rectifier into the slot along the guide rails until it is engaged. Close the handle,
and push the locking latch towards the right to lock the handle, as shown in Figure 4-2.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 41

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Figure 4-2 Installing a rectifier

Step 7 Remove the protective gloves.

----End

Follow-up Procedure
Pack the removed component and send it to the local Huawei warehouse.

4.4.2 Replacing a Circuit Breaker

Prerequisites

Before replacing an AC circuit breaker, switch off the input circuit breaker on the upper-level
device.
 You have obtained the cabinet door key, insulation tapes, and tools.
 The new circuit breaker is intact, has the same specifications, and is OFF.

Procedure
Step 1 Unscrew and remove the cover before the circuit breaker.
Step 2 Switch off the circuit breaker that is to be replaced.
Step 3 Record connection positions of output cables.
Step 4 Loosen the screws that secure ports on the circuit breaker using a Phillips screwdriver and
remove the cables. Wrap the cables using insulation tapes to prevent hazards.
Step 5 Loosen the screw that secures the lower port of the circuit breaker by using a Phillips
screwdriver, and loosen the buckle at the circuit breaker base by using an insulated flat-head
screwdriver.
Step 6 Remove the circuit breaker from the guide rail. Figure 4-3 shows the procedure for removing
the circuit breaker.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 42

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Figure 4-3 Removing the circuit breaker

Step 7 Switch off the new circuit breaker. Press the buckle at the circuit breaker base by using an
insulated flat-head screwdriver and install the new circuit breaker. Then loosen the buckle and
secure the circuit breaker to the guide rail.
Step 8 Tighten the screw that secures the lower port of the circuit breaker.
Step 9 Remove the insulation tapes from the output cables. Then connect the output cables to the
circuit breaker ports and tighten the screws.
Step 10 Switch the circuit breaker to ON, as shown in Figure 4-4.

Figure 4-4 Installing a circuit breaker

Step 11 Reinstall the cover and tighten the screws.

----End

4.4.3 Replacing a Plug-in Circuit Breaker

Prerequisites
 You have obtained the cabinet door key and tools.
 The new circuit breaker is intact.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 43

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Procedure
Step 1 Loosen the screws and remove the front cover from the circuit breaker.
Step 2 Hold the faulty circuit breaker and pull it out, as shown in the following figure.

Figure 4-5 Removing a plug-in circuit breaker

Step 3 Switch off the new circuit breaker and install it in the correct position.
Step 4 Switch on the new circuit breaker.
Step 5 Tighten the screws and install the front cover on the circuit breaker.
----End

4.4.4 Replacing the PCB of UIM02C

Prerequisites
 An ESD wrist strap, ESD gloves, ESD box or bag, cabinet door key, and required tools
are available.
 The new printed circuit board (PCB) of UIM02C is intact.

Procedure
Step 1 Connect the ground cable of the ESD wrist strap, and wear the ESD wrist strap and ESD
gloves.
Step 2 Record the signal cable connection positions on the UIM02C panel and disconnect the cables.
Step 3 Unscrew the UIM02C panel and remove the UIM02C, as shown in Figure 4-6.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 44

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Figure 4-6 Removing the UIM02C

Step 4 Remove the -48 V power cable from the PCB of UIM02C.

Figure 4-7 Removing the -48 V power cable

Step 5 Record the positions where the PCB of UIM02C connects to all the cables, and then
disconnect the cables.
Step 6 Remove the PCB, as shown in Figure 4-8.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 45

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Figure 4-8 Removing the PCB of UIM02C

Step 7 Take out the new PCB and install it.

Step 8 Connect all cables back to the new PCB based on the recorded information.
Step 9 Connect the -48 V power cable to the PCB of UIM02C.
Step 10 Push in the UIM02C and tighten the screws.
Step 11 Reconnect the signal cables to the UIM02C panel based on the recorded information.
Step 12 Disconnect the ground cable of the ESD wrist strap, and remove the ESD wrist strap and ESD
gloves.
----End

Follow-up Procedure
Pack the removed component and send it to the local Huawei warehouse.

4.4.5 Replacing an SMU

Prerequisites
 The cabinet door key is available.
 The new SMU is intact.

Procedure
Step 1 Push the locking latch towards the left.
Step 2 Pull the handle outwards and remove the SMU, as shown in Figure 4-9.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 46

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Figure 4-9 Removing an SMU

Step 3 Insert the new SMU into the subrack, push the locking latch towards the left, and pull out the
handle.
Step 4 Slide the SMU into the subrack slowly along the guide rails, push in the handle, and then push
the locking latch towards the right.
Step 5 Reset the parameters on the SMU.

Figure 4-10 Installing an SMU

----End

Follow-up Procedure
Pack the removed component and send it to the local Huawei warehouse.

4.4.6 Replacing an AC SPD Module

Prerequisites
 You have obtained an ESD wrist strap or a pair of ESD gloves, an ESD box or bag, and
the cabinet door key.
 The new AC SPD module is intact and the indication window is green.

Do not replace an AC SPD module during a thunderstorm.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap and wear the ESD wrist strap and ESD
gloves.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 47

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Step 2 Hold down the faulty AC SPD module and pull it out, as shown in Figure 4-11.
Step 3 Install a new AC SPD module, as shown in Figure 4-11.

Figure 4-11 Replacing an AC SPD module

Step 4 Disconnect the ground cable from the ESD wrist strap and take off the ESD wrist strap and
ESD gloves.
----End

Follow-up Procedure
Check that the alarm for the AC SPD is cleared.

4.4.7 Replacing a Direct Ventilation Fan

Prerequisites
 You have obtained an ESD wrist strap, a pair of ESD gloves, an ESD box or bag, the
cabinet door key, and tools.
 The new fan is intact.

Install the fan according to airflow directions. Do not install the fan reversely.

Context
You need only to disconnect the fan power cable, but not the AC input to the system.

Procedure
Step 1 Disconnect the 48 V power cable from the UIM02C.
1. Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap and
ESD gloves.
2. Record the positions of signal cables on the UIM02C, and disconnect the cables.
3. Unscrew and remove the UIM02C, as shown in Figure 1.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 48

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

4. Disconnect the 48 V power cable from the UIM02C, as shown in Figure 2.

Step 2 Disconnect the interconnection terminal from the fan power cable.
Step 3 Record the fan installation direction and remove the fan, as shown in the following figure.

Figure 4-12 Removing a fan

Step 4 Install the new fan according to the fan installation direction you recorded.
Step 5 Reconnect the interconnection terminal to the fan power cable.
Step 6 Reinstall the UIM02C.
1. Connect the 48 V power cable to the UIM02C.
2. Insert the UIM02C into the correct slot, and tighten the screws.
3. Reconnect the signal cables to the UIM02C based on the recorded information.
4. Disconnect the ground cable from the ESD wrist strap, and take off the ESD wrist strap
and ESD gloves.
----End

4.4.8 Replacing an Air Filter

Prerequisites
 You have obtained the cabinet door key and tools.
 The new air filter is intact.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 49

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Context
The air filter can be directly replaced without the need to disconnect the AC input to the
system.

Procedure
Step 1 Unscrew and remove the air filter, as shown in the following figure.

Figure 4-13 Removing an air filter

Step 2 Correctly place the new air filter (keep the side with a label upwards and the surface with a
rubber strip facing the cabinet door). Tighten the screws to secure the air filter.
----End

4.4.9 Replacing a Heater

Prerequisites
 You have prepared an ESD wrist strap, a pair of ESD gloves, the cabinet door key, and
tools.
 The new heater is intact.

Before replacing the heater, ensure that its circuit breaker is OFF.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap and ESD
gloves.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 50

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Step 2 Switch off the heater circuit breaker on the AC PDU.

Step 3 Unscrew and remove the heater, as shown in the following figure.

Figure 4-14 Removing a heater

Step 4 Record the cable connection positions on the heater and disconnect the cables.
Step 5 Connect the cables to the new heater based on the recorded information.
Step 6 Place the new heater in position and tighten the screws.
Step 7 Switch on the heater circuit breaker on the AC PDU.
Step 8 Disconnect the ground cable from the ESD wrist strap, and take off the ESD wrist strap and
ESD gloves.
----End

4.4.10 Replacing a Battery Temperature Sensor

Prerequisites
 You have obtained an ESD wrist strap, a pair of ESD gloves, an ESD box or bag, the
cabinet door key, and a maintenance tool kit.
 The new battery temperature sensor is intact.

Procedure
Step 1 Connect the ground cable to the ESD wrist strap, and put on the ESD wrist strap and ESD
gloves.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 51

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Step 2 Remove the battery temperature sensor cable from the UIM, as shown in Figure 4-15.

Figure 4-15 Removing the battery temperature sensor cable

Step 3 Cut off the cable tie of the battery temperature sensor and remove the sensor.

The detection probe must not contact a metal surface.

Figure 4-16 Position of the battery temperature sensor

Step 4 Properly place the new battery temperature sensor and bind it securely with a cable tie.
Step 5 Reconnect the battery temperature sensor cable to the UIM.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 52

TP48200A-DX12A1 Telecom Power
User Manual 4 Maintenance

Step 6 Disconnect the ground cable from the ESD wrist strap, and take off the ESD wrist strap and
ESD gloves.
----End

4.4.11 Replacing a Door Status Sensor

Prerequisites
 The cabinet door key and required tools are available.
 The new door status sensor is intact.

Procedure
Step 1 Open the cabinet door and remove the shell of the door status sensor.
Step 2 Record the positions where the alarm cables connect to the door status sensor, and unscrew
the alarm cables.
Step 3 Unscrew the door status sensor, as shown in Figure 4-17.

Figure 4-17 Removing the door status sensor

Step 4 Remove the shell of the new door status sensor and remove the screws from the alarm cables.
Step 5 Properly place the new door status sensor at the installation position and tighten the screws.
Step 6 Place the alarm cables in sequence and secure the screws.
Step 7 Reinstall the shell of the door status sensor.
----End

Follow-up Procedure
Check that the door status alarm is cleared.

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 53

 TP48200A-DX12A1 Telecom Power
User Manual A Technical Specifications

A Technical Specifications

A.1 Environment Specifications

Table A-1 Environment specifications

Item Specifications
Operating temperature –33ºC to +40ºC with 1120 W/m2 solar radiation
Transport temperature –40ºC to +70ºC
Storage temperature –40ºC to +70ºC
Operating humidity 5%–95% RH
Storage humidity 5%–95% RH
Altitude 0–4000 m
When the altitude ranges from 2000 m to 4000 m, the operating
temperature decreases by 1°C for each additional 200 m.

Others There should be no conductive dust, corrosive gas, or explosion

hazard.
Dust, corrosive substances, pests, molds, and other indicators should
be controlled in accordance with class 4.1 requirements in ETSI EN
300 019-1-4 (V2.2.1).

A.2 Electrical Specifications

Table A-2 Electrical specifications

Item Specifications
AC input Input system 220/380 V AC three-phase
Input voltage 85–300 V AC

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 54

TP48200A-DX12A1 Telecom Power
User Manual A Technical Specifications

Item Specifications
Input frequency Frequency range: 45–66 Hz; nominal
frequency: 50 Hz or 60 Hz
Power factor ≥ 0.99 (rated input; rated load)
THD ≤ 5% (Vin: 208 V AC, 220 V AC, or 230 V
AC; load: 50%–100%)
DC output Output voltage range –42 V DC to –58 V DC
Default output voltage –53.5 V DC
Output power Maximum output power = Output power of
a single rectifier x Number of rectifiers
Regulated voltage precision ≤ ±1%
Ripple and noise ≤ 200 mVp-p
Psophometrically weighted noise ≤ 2 mV
Current imbalance < ±5% (50%–100% load)
AC input AC input overvoltage protection threshold > 300 V AC
protection
AC input overvoltage recovery threshold When the voltage is restored to 290 V AC,
the output resumes.
AC input undervoltage protection threshold < 85 V AC
AC input undervoltage recovery threshold When the voltage is restored to 90 V AC,
the output resumes.
DC output DC output overvoltage protection threshold –58.5 V DC to –60.5 V DC
protection 1. If overvoltage occurs inside a rectifier,
the rectifier locks out.
2. If the external voltage is greater than
–63 V for more than 500 ms, the
rectifier locks out.
AC surge Type 1 + Type 2
protection
DC surge 10 kA (8/20 μs) in differential mode; 20 kA (8/20 μs) in common mode
protection
Safety IEC/EN60950-1
compliance
Mean time 200,000 hours
between failures
(MTBF)

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 55

 TP48200A-DX12A1 Telecom Power
User Manual A Technical Specifications

A.3 EMC Specifications

Table A-3 EMC specifications

Item Specifications
Electromagnetic Conducted emission (CE) AC port: EN300386 Class B
interference (EMI) DC port: EN300386 Class A
Signal port: EN300386 Class B
Radiated emission (RE) Class B, EN300386
Harmonic current IEC61000-3-12
Voltage fluctuation and flicker IEC61000-3-11
Electromagnetic ESD IEC61000-4-2 (criterion B)
susceptibility (EMS) Contact discharge: 6 kV; air discharge: 8 kV
Electrical fast transient (EFT) IEC61000-4-4 (criterion B)
AC power port: 2 kV; DC power port: 1 kV;
signal port: 1 kV
Radiated susceptibility (RS) IEC61000-4-3 (criterion A)
10 V/m
Conducted susceptibility (CS) IEC6100-4-6 (criterion A)
Power port: 10 V; signal port: 3 V
Surge immunity IEC61000-4-5 (criterion B)
AC power port: differential mode: 2 kV (8/20
µs); common mode: 4 kV (8/20 µs)
DC power port: differential mode: 2 kV (8/20
µs); common mode: 4 kV (8/20 µs)
Signal port: differential mode: 0.5 kV; common
mode: 1 kV
Voltage dips immunity (DIP) EN61000-4-11

A.4 Cabinet Specifications

Table A-4 Cabinet specifications

Item Specifications
Cabinet dimensions (H x W x D)  TP48200A-DX12A1: 1200 mm x 650 mm x 650 mm
 Base: 150 mm x 650 mm x 650 mm
Cabinet weight ≤ 115 kg (excluding rectifiers and batteries)
Protection level IP55

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 56

 TP48200A-DX12A1 Telecom Power
User Manual A Technical Specifications

Item Specifications
Installation mode Floor-mounted
Maintenance mode Operated and maintained from the front
Cabling Routed in and out from the bottom

A.5 Heater Specifications

Table A-5 Heater specifications

Item Specifications
Input voltage 220 V AC single-phase or 110 V AC dual-live wire
Voltage frequency Rated frequency: 50 Hz or 60 Hz
Operating temperature -40°C to +65°C (-40°F to +149°F)
Heater start and stop temperature The heater starts when the temperature is 0°C and stops when the
temperature is 15°C.
Operating humidity 5% RH to 95% RH
Heating power > 500 W

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 57

TP48200A-DX12A1 Telecom Power
User Manual B Electrical Conceptual Diagrams

B Electrical Conceptual Diagrams

Figure B-1 TP48200A-DX12A1 (DC2) electrical conceptual diagram

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 58

 TP48200A-DX12A1 Telecom Power C Associations Between Alarms and Dry Contacts on the
User Manual UIM

C Associations Between Alarms and Dry

Contacts on the UIM

Table C-1 Associations between UIM02C dry contacts and alarms

Port Type Silk Name Category Associated Alarm

Screen
Dry contact DIN1 - - Dry contact input 1 (open: normal;
input ports closed: alarm)
DIN2 - - Dry contact input 2 (open: normal;
closed: alarm)
DIN3 - - Dry contact input 3 (open: normal;
closed: alarm)
DIN4 - - Dry contact input 4 (open: normal;
closed: alarm)
DIN5 - - Heater Fault (closed: normal; open:
alarm)
DIN6 - - Dry contact input 6 (open: normal;
closed: alarm)
Dry contact ALM1 Urgent alarm System BLVD Warning/BLVD
output ports incident Disconnected/Batt. Fuse Break/SMU
The default Fault/Batt Test Negative/Rectifier
setting (closed: Fault/DC Undervolt./DC Ultra
normal; open: Undervolt.
alarm) can be ALM2 Not urgent alarm System Insuff. Rdnt. Rects./Rectifier Fault/Fan
modified. incident Fault/AC Ph. Failure
ALM3 System incident AC main AC Ph. Failure/AC Failure/Long Mains
AC Failure
ALM4 – – Ret. Vent TS Fault/Fan Fault
ALM5 Rectifier incident - Rectifier Fault
ALM6 Battery incident - Batt. Fuse Break/Batt Test Negative

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 59

TP48200A-DX12A1 Telecom Power C Associations Between Alarms and Dry Contacts on the
User Manual UIM

Port Type Silk Name Category Associated Alarm

Screen

ALM7 Temperature alarm High/low Batt. High Temp./Batt. Low

temperature Temp./High temp/Heater Fault
ALM8 Door contact Door open Door Alarm

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 60

TP48200A-DX12A1 Telecom Power
User Manual D Acronyms and Abbreviations

D Acronyms and Abbreviations

A
AC alternating current

B
BLVD battery low voltage disconnection

D
DC direct current

F
FE fast ethernet

H
HAU heater assembly unit
HTTPS Hypertext Transfer Protocol Secure

I
IP Internet Protocol

L
LCD liquid crystal display
LLVD load low voltage disconnection

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 61

TP48200A-DX12A1 Telecom Power
User Manual D Acronyms and Abbreviations

S
SMU site monitoring unit
SNMP Simple Network Management Protocol

T
TCUC Temperature control unit C

U
UIM user interface module

Issue 07 (2019-11-15) Copyright © Huawei Technologies Co., Ltd. 62