Scribd
Upload
49 views

Konfigurasi Routing Ospf

The document describes the steps to configure OSPF routing between three routers: 1. Interface IPs are configured on each router and their connected networks. 2. OSPF process 1 is configured on each router with their connected networks added. 3. Adjacencies form successfully between the routers over their connected interfaces.

Uploaded by

Mohamad Edi Fakhrurozi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
49 views

Konfigurasi Routing Ospf

The document describes the steps to configure OSPF routing between three routers: 1. Interface IPs are configured on each router and their connected networks. 2. OSPF process 1 is configured on each router with their connected networks added. 3. Adjacencies form successfully between the routers over their connected interfaces.

Uploaded by

Mohamad Edi Fakhrurozi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 9

KONFIGURASI ROUTING OSPF

1. Pertama pilih perangkat yang akan digunakan untuk konfigurasi routing OSPF lalu
sambungkan kablenya.

2. Kemudian klik Router lalu konfigurasi seperti dibawah ini.


R1

Router>ena

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip address 172.168.1.17 255.255.255.240

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up


Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip address 198.16.10.5 255.255.255.252

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial2/0, changed state to down

Router(config-if)#exit

Router(config)#int se3/0

Router(config-if)#ip address 198.16.10.1 255.255.255.252

Router(config-if)#no sh

R2

Router>ena

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip address 20.10.0.1 255.255.255.0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config)#int se2/0
Router(config-if)#ip address 198.16.10.2 255.255.255.252

Router(config-if)#no sh

Router(config-if)#exit

Router(config)#int se3/0

Router(config-if)#ip address 198.16.10.9 255.255.255.252

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial3/0, changed state to down

Router(config)#end

R3

Router>ena

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip address 172.168.1.33 255.255.255.248

Router(config-if)#no sh

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip address 198.16.10.6 255.255.255.252

Router(config-if)#no sh
Router(config-if)#

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit

Router(config)#int se3

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config-if)#ip address 198.16.10.10 255.255.255.252

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial3/0, changed state to up

Router(config-if)#exit

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up

Router(config)#end

3. Kemudian masukan ip pada masing-masing PC.


4. Kemudian masuk Router kembali untuk melakukan konfigurasi OSPF
R1
Router>ena

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#router ospf 1

Router(config-router)#network 172.168.1.16 0.0.0.15 area 0

Router(config-router)#network 198.16.10.0 0.0.0.3 area 0

Router(config-router)#network 198.16.10.4 0.0.0.3 area 0

Router(config-router)#end

Router#

%S00:27:44: %OSPF-5-ADJCHG: Process 1, Nbr 198.16.10.9 on Serial3/0 from LOADING to FULL,


Loading Done

00:32:24: %OSPF-5-ADJCHG: Process 1, Nbr 198.16.10.10 on Serial2/0 from LOADING to FULL,


Loading Done
YS-5-CONFIG_I: Configured from console by console

R2
Router>ena

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#router ospf 1

Router(config-router)#network 20.10.0.0 0.0.0.255 area 0

Router(config-router)#network 198.16.10.0 0.0.0.3 area 0

Router(config-router)#

00:59:39: %OSPF-5-ADJCHG: Process 1, Nbr 198.16.10.5 on Serial2/0 from LOADING to FULL,


Loading Done

Router(config-router)#network 198.16.10.8 0.0.0.3 area 0

Router(config-router)#end

Router#

%SYS-5-CONFIG_I: Configured from console by console

01:04:57: %OSPF-5-ADJCHG: Process 1, Nbr 198.16.10.10 on Serial3/0 from LOADING to FULL,


Loading Done

R3
Router>ena

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#router ospf 1
Router(config-router)#network 172.168.1.32 0.0.0.7 area 0

Router(config-router)#network 198.16.10.4 0.0.0.3 area 0

Router(config-router)#

00:32:21: %OSPF-5-ADJCHG: Process 1, Nbr 198.16.10.5 on Serial2/0 from LOADING to FULL,


Loading Done

Router(config-router)#network 198.16.10.8 0.0.0.3 area 0

Router(config-router)#end

Router#

%SYS-5-CONFIG_I: Configured from console by console

00:32:59: %OSPF-5-ADJCHG: Process 1, Nbr 198.16.10.9 on Serial3/0 from LOADING to FULL,


Loading Done

5. Setelah konfigurasi telah selesai lakukan ping pada masing-masing PC.

You might also like