Scribd
Upload
509 views

SOP For TOSHIBA VFD

This document provides instructions for changing the frequency setting on an inverter and enabling parameter protection on the device. The steps include: 1) Removing parameter selection protection by changing the value from 1 to 0. 2) Changing the frequency setting by navigating to the appropriate menu option and rotating the setting dial. 3) Re-enabling parameter protection by changing the value back from 0 to 1. 4) Returning to the home screen by pressing the mode button twice. The instructions are presented through labeled diagrams of the inverter control panel.

Uploaded by

Joseph Jojo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
509 views

SOP For TOSHIBA VFD

This document provides instructions for changing the frequency setting on an inverter and enabling parameter protection on the device. The steps include: 1) Removing parameter selection protection by changing the value from 1 to 0. 2) Changing the frequency setting by navigating to the appropriate menu option and rotating the setting dial. 3) Re-enabling parameter protection by changing the value back from 0 to 1. 4) Returning to the home screen by pressing the mode button twice. The instructions are presented through labeled diagrams of the inverter control panel.

Uploaded by

Joseph Jojo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

 

Prepared By: Wasim Pinjara


Guided By: Ganesh Mule

 
 
Oeration Panel  
 

   

Run Lamp
％ lamp Hz lamp RUN key
Lit when a frequency is not
output with the ON run Displayed numbers Pressing this key
Displayed numbers
command. This lamp blinks are in Hertz. while the RUN key
are in %.
when operation starts. lamp is on starts
operation.

RUN key lamp


PRG lamp
Lights when the
When lit, the inverter is in RUN key is enabled.
parameter setting mode.
When blinking, the inverter
is in AUH STOP key
While the RUN lamp
is blinking, pressing
MON lamp this key once to slow
down and stop the
While this is lit, the inverter
is in monitor mode. While inverter. During the
terminal block
blinking, the inverter is in
"Past Trip History Details operation, pressing
this key twice for
Monitor Display".
emergency stop.
During trip, pressing
this key twice for
Setting dial Center of the setting EASY key reset.
Turning the dial left and dial
Switches between
right changes the operation Pressing the center of the easy and standard
frequency, parameters and setting dial is used for setting modes MODE key
etc. determining values
Switches between
EASY key lamp run, settings, and
Setting dial lamp
status monitor 
Setting the operation Lights when the d
frequency while this lamp is EASY key is
lit. enabled.

 
 
STEP 1: Remove Parameter Selection Protection
 

     

     
1. Press
  Mode
button.
 

   

2. Rotate
Setting
Dial Up to
F7.

3. Press Centre of
Setting Dial.

 
 
 
4. Make 0 instead of 1 for
 
remove protection
  (Unlocked) to do changes
 

  Rotate Dial to change 1 to 0


             

   

Now it is Unlocked for changes in setting.

 
 
Step 2: Changing the Frequency
 

 
1. Press
 
Mode
  button for
back.
 
 
 

  2. Rotate
  Setting
Dial Up to
  Sr 2 for
  change
frequency.
 

   

 
3. Press Centre of
  Setting Dial.

   

 
4. Rotate Setting Dial
  for required frequency.
   

 
 
 

  5. Press
Mode
  button for
 
back.

   

Step 3:Enable Parameter Protection


 

 
1. Rotate
 
Setting
  Dial Up to
F7.
 

 
2. Press Centre of
  Setting Dial
 

   

 
 
  3. Make 1 instead of 0
for Protection
  (Locked).
 

 
Rotate Dial to change 0 to 1
 

   

   

 
Now your setting is protected (Locked)
 

 
 
Step 4: Back to Home Screen
 

   

  1. Press Mode
  button twice for
back.
 

   

Home Screen

 
 

You might also like