5713229761/02.

16

De’Longhi Appliances via Seitz, 47 31100 Treviso Italy www.delonghi.com

 ECAM35X.75

BEAN TO CUP ESPRESSO AND

CAPPUCCINO MACHINE
Instruction for Use

Instructions videos available at:

http://ecam35075.delonghi.com
 EN
page 6

B1
B

B3
B2
B4

B6
B5
B7
B8
B10
B11 B9
B14 B13

B12 B15

C D
C1 C2
D1
D2

C3 C4
D3
C5 D5
D4

C6 C7

2
 A1
A

A2

A3

A5
A6 A4
A7
B A22

A8 A21
A9

A10 A20
A19

A11

A12

A16
A13

A14

A17

A15 A18

3
 3A 3A

1 1 2 2 3B 3B 4 4

5 5 6 6 7 7 8 8

9 9 10 10 11 11 12 12

13 13 14 14 15 15 16 16
4
 4 17 17 18 18 19 19 20 20

24A 24A

8 21 21 22 22 23 23 24B 24B
SH

SH
PU

PU
SH

SH
PU

PU

12 25 25 26 26 27 27 28 28

A AB B

B B

A A
16 29 29 30 30 31 31 32 32
5
CONTENTS 13. DELIVERING HOT WATER........................... 16
1. FUNDAMENTAL SAFETY WARNINGS..............7 14. CLEANING................................................ 16
2. SAFETY WARNINGS .....................................8 14.1 Cleaning the machine..................................16
2.1 Symbols used in these instructions................8 14.2 Cleaning the machine's internal circuit........16
2.2 Designated use...............................................8 14.3 Cleaning the coffee grounds container.........17
2.3 Instruction for Use..........................................8 14.4 Cleaning the drip tray and condensate tray..17
14.5 Cleaning the inside of the coffee machine....17
3. INTRODUCTION...........................................8 14.6 Cleaning the water tank...............................17
3.1 Letters in brackets..........................................8 14.7 Cleaning the coffee spouts...........................17
3.2 Troubleshooting and repairs...........................8 14.8 Cleaning the pre-ground coffee funnel........17
4. DESCRIPTION.............................................9 14.9 Cleaning the infuser.....................................17
4.1 Description of the appliance ..........................9 14.10 Cleaning the milk container.........................18
4.2 Description of the accessories.........................9 14.11 Cleaning the hot water nozzle......................18
4.3 Description of the milk container...................9 15. DESCALING............................................... 18
5. BEFORE USE...............................................9 16. SETTING WATER HARDNESS....................... 19
5.1 Checking the appliance..................................9 16.1 Measuring water hardness...........................19
5.2 Installing the appliance..................................9 16.2 Setting water hardness................................19
5.3 Connecting the appliance.............................10
5.4 Setting up the appliance..............................10 17. WATER SOFTENER FILTER.......................... 19
17.1 Installing the filter.......................................20
6. TURNING THE APPLIANCE ON.................... 10 17.2 Replacing the filter.......................................20
7. TURNING THE APPLIANCE OFF................... 10 17.3 Removing the filter......................................21
8. MENU SETTINGS....................................... 11 18. TECHNICAL DATA....................................... 21
8.1 Language.....................................................11 19. DISPOSING OF THE APPLIANCE.................. 21
8.2 Maintenance................................................11
8.3 Program beverages......................................11 20. DISPLAYED MESSAGES............................... 21
8.4 Program My beverages................................11 21. TROUBLESHOOTING.................................. 24
8.5 General........................................................11 22. ELECTRICAL REQUIREMENTS..................... 26
8.6 Statistics.......................................................12
9. RINSING................................................... 12
10. MAKING COFFEE........................................ 13
10.1 Adjusting the coffee mill..............................13
10.2 Tips for a hotter coffee.................................13
10.3 Making automatic recipes using coffee beans..
...................................................................13
10.4 Temporarily varying the coffee aroma..........14
10.5 Making coffee using pre-ground coffee........14
11. MAKING CAPPUCCINOS AND MILK-BASED
COFFEES................................................... 14
11.1 Filling and attaching the milk container.......15
11.2 Adjusting the amount of froth......................15
11.3 Making cappuccino and milk-based coffees
automatically...............................................15
11.4 Cleaning the milk container after use ..........15
12. “ ” PROGRAMMING AND SELECTING...
................................................................ 16

6
1. FUNDAMENTAL SAFETY WARNINGS
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children without supervision.
• Never clean by immersing the appliance in water.
• This is an household appliance only. It is not intended to be used in: staff kitchen
areas in shops, offices and other working environments; farm houses; by clients in
hotels, motels and other residential type environments; bed and breakfast type
environments.
• If the plug or cord is damaged, it must be replaced by Customer Services only to avoid
all risk.

FOR EUROPEAN MARKETS ONLY:

• This appliance can be used by children aged from 8 years and above if they have been
given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. User cleaning and maintenance shall not be made
by children unless they are above 8 years old and supervised. Keep the appliance and
power cord away from children under 8 years of age.
• Appliances can be used by persons with reduced physical, sensory or mental capabil-
ities or lack of experience and knowledge if they are supervised or have been given
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.
• Children shall not play with the appliance.
• Always unplug the appliance when left unattended and before assembly, taking apart
or cleaning.
Surfaces marked with this symbol become hot during use (the symbol is present in
certain models only).

7
2. SAFETY WARNINGS Any other use is considered improper and thus dangerous. The
2.1 Symbols used in these instructions manufacturer is not liable for damage deriving from improper
Important warnings are identified by these symbols. It is vital to use of the appliance.
respect these warnings.
2.3 Instruction for Use
Danger!
Read this Instruction for Use carefully before using the appli-
Failure to observe the warning may result in life threatening
ance. Failure to follow this Instruction for Use may result in
injury by electric shock.
burns or damage to the appliance.
Important! The manufacturer is not liable for damage deriving from failure
Failure to observe the warning could result in injury or damage to respect this Instruction for Use.
to the appliance.
Please note:
Danger of burns! Keep this Instruction for Use. If the appliance is passed to other
Failure to observe the warning could result in scalds or burns. persons, they must also be provided with this Instruction for
Please note: Use.
This symbol identifies important advice or information for the
user. 3. INTRODUCTION
Thank you for choosing this bean to cup espresso and cappuc-
cino machine.
Danger! We hope you enjoy using your new appliance. Take a few min-
This is an electrical appliance and may cause electric shock. utes to read this Instruction for Use. This will avoid all risks and
You should therefore follow these safety warnings: damage to the appliance.
• Never touch the appliance with damp hands or feet.
• Never touch the plug with damp hands. 3.1 Letters in brackets
• Make sure the socket used is freely accessible at all times, The letters in brackets refer to the legend in the description of
enabling the appliance to be unplugged when necessary. the appliance on pages 2-3.
• Unplug directly from the plug only. Never pull the cord as
you could damage it.
3.2 Troubleshooting and repairs
• To disconnect the appliance completely you must unplug it
In the event of problems, first try and resolve them by reading
from the mains socket.
the information given in sections “20. Displayed messages” and
• If the appliance is faulty, do not attempt to repair.
“21. Troubleshooting”.
Turn it off, unplug from the mains socket and contact Cus-
If this does not resolve the problem or you require further in-
tomer Services.
formation, you should consult Customer Services by calling the
• Before cleaning the appliance, turn it off, unplug from the
number given on the annexed "Customer Service" sheet.
mains socket and allow to cool.
If your country is not among those listed on the sheet, call the
Important: number given in the guarantee. If repairs are required, contact
Keep all packaging (plastic bags, polystyrene foam) away from De’Longhi Customer Services only. The addresses are given in
children. the guarantee certificate provided with the machine.
Danger of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
When the appliance is in operation, the cup shelf could become
very hot.

2.2 Designated use

This appliance is designed and made to prepare coffee and heat
beverages.

8
e 4. DESCRIPTION B11. : Cappuccino
4.1 Description of the appliance B12. : Latte Macchiato
(page 3 - A) B13. : Hot Milk
A1. Beans container lid B14. : Beverage selection menu (other than directly
A2. Pre-ground coffee funnel lid selected beverages): Long Espresso, Short Espresso, Dop-
- A3. Beans container pio+, Cappuccino+, Caffelatte, Flat white, Espresso mac-
A4. Pre-ground coffee funnel chiato, 2 Espresso, 2 Short Espresso, 2 Long Espresso, Hot
A5. Grinding adjustment dial Water
e A6. Cup shelf B15. : My beverages selection menu. Unless previous-
A7. button: to turn the appliance on and off (standby) ly programmed from the settings menu (“8.4 Program My
A8. Hot water and steam connection nozzle beverages”), the beverage is programmed directly the first
r A9. Coffee spouts (adjustable height) time you use the appliance.
A10. Condensate tray
A11. Coffee grounds container 4.2 Description of the accessories
A12. Cup tray (page 2 - C )
A13. Drip tray water level indicator C1. Indicator paper
A14. Drip tray grille C2. Pre-ground coffee measure
-
A15. Drip tray C3. Descaler
A16. Water tank lid C4. Water softener filter (certain models only)
- A17. Water tank
d C5. Cleaning brush
A18. Water softener filter housing C6. Hot water spout
A19. Infuser door C7. Power cord
A20. Infuser
A21. Power cord connector socket 4.3 Description of the milk container
A22. Main switch
(page 2 - D )
D1. Froth adjustment and CLEAN dial
Description of the touch screen D2. Milk container lid
(page 2 - B ) D3. Milk container
g A number of buttons on the panel have a double function. This is D4. Milk intake tube
d indicated in brackets in the description. D5. Frothed milk spout (adjustable)
B1. Display: guides the user in using the appliance. The current
- selection is at the centre between two dotted lines. 5. BEFORE USE
e B2. ▼ Selection arrow(“ESC”: when programming beverages,
press to exit without saving the change) 5.1 Checking the appliance
e B3. OK: to confirm the selection(During the first few seconds of After removing the packaging, make sure the product is com-
t "espresso", "short espresso" or "long espresso" delivery, press plete and undamaged and that all accessories (C) are pres-
n for 2 cups) ent. Do not use the appliance if it is visibly damaged. Contact
B4. ▲ Selection arrow(“STOP” - When delivering/program- De’Longhi Customer Services.
ming beverages, press to interrupt/programme)
B5. /ESC: to perform a rinse cycle. 5.2 Installing the appliance
(When in the settings menu, it acts as the "ESC" button to exit Important!
from the selected function and go back to the main menu) When you install the appliance, you should respect the follow-
B6. : appliance settings menu ing safety warnings:
B7. : aroma selection • The appliance gives off heat. After positioning the appli-
ance on the worktop, leave a space of at least 3 cm be-
Directly selected beverages: tween the surfaces of the appliance and the side and rear
B8. : Espresso walls and at least 15 cm above the coffee maker.
B9. : Coffee • Water penetrating the coffee machine could cause
B10. : Long damage.
Do not place the appliance near taps or sinks.

9
• The appliance could be damaged if the water it contains
freezes. Please note:
Do not install the appliance in a room where the tempera- • The first time you use the coffee maker, you need to make
ture could drop below freezing point. 4-5 cups of coffee or 4-5 cappuccinos before it starts to give
• Arrange the cord (C7) in such a way that it cannot be dam- satisfactory results.
aged by sharp edges or contact with hot surfaces (e.g. elec- • When making the first 5-6 cappuccinos, it is normal to hear
tric hot plates). the noise of boiling water. After this, the noise becomes
less.
5.3 Connecting the appliance • To enjoy your coffee even more and improve the perfor-
mance of your appliance, we recommend installing a
Important!
water softener filter (C4) as described in section “17. Water
Check that the mains power supply voltage corresponds to that
softener filter”. If your model is not provided with a filter,
indicated on the rating plate on the bottom of the appliance.
you can request one from De'Longhi Customer Services.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
6. TURNING THE APPLIANCE ON
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified Please note:
professional. Before turning the appliance on, make sure the main switch
(A22) on the back of the appliance is pressed (fig. 2).
5.4 Setting up the appliance Each time the appliance is turned on, it performs an automatic
Please note: preheat and rinse cycle which cannot be interrupted. The appli-
• Coffee has been used to factory test the appliance and it is ance is ready for use only after completion of this cycle.
therefore completely normal for there to be traces of cof- Danger of burns!
fee in the mill. The machine is, however, guaranteed to be During rinsing, a little hot water comes out of the coffee spouts
new. (A9) and is collected in the drip tray (A15) underneath. Avoid
• You should customise water hardness as soon as possible contact with splashes of water.
following the instructions in section “16. Setting water
hardness”. • To turn the appliance on, press the button (A7) (fig.
6). The message "Heating Please wait" appears on the dis-
1. Plug the power cord (C7) connector into the socket (A21) at play (B1).
the back of the appliance and connect the appliance to the After heating, the message "Rinsing" is displayed, together with
mains electricity supply (fig. 1). Make sure the main switch a progress bar which gradually fills as preparation proceeds. As
(A22) at the back of the appliance is pressed (fig. 2); well as heating the boiler, the appliance also heats the internal
2. "Language": press the selection arrow (B2) until the re- circuits by circulating hot water.
quired language is displayed between the two dotted The appliance is at temperature when the message "Select your
lines, then press OK (B3) to confirm. beverage" is displayed.
Then follow the instructions indicated on the appliance display
(B1):
7. TURNING THE APPLIANCE OFF
3. “Fill tank”: remove the water tank (A17), fill to the MAX
Whenever the coffee machine is turned off after being used to
line with fresh water (fig. 3A), then replace in the appli-
make coffee, it performs an automatic rinse cycle.
ance (fig. 3B);
4. "Insert water spout": Check that the hot water spout (C6) Danger of burns!
is inserted on the connection nozzle (A8) (fig. 4) and place During rinsing, a little hot water flows from the coffee spouts
a container holding a minimum of 100 ml underneath (fig. (A9). Avoid contact with splashes of water.
5); • To turn the appliance off, press the button (A7) (fig.
5. "Water circuit empty, Fill water circuit, Hot water, 6);
Confirm?"; • The message "Turning off underway Please wait" appears
6. Press the OK button to confirm. The appliance delivers hot on the display (B1), then the appliance performs a rinse
water from the spout then goes off automatically. cycle and goes off (standby).
The coffee machine is now ready for normal use.
10
 2. Press the selection arrows (B2 and B4) until "Maintenance"
Please note! is displayed between the two lines;
If you will not be using the appliance for some time, unplug 3. Press OK (B3) to confirm;
e from the mains socket: 4. Press the selection arrows to display the operation to be
• first turn the appliance off by pressing the button performed;
(fig. 6); 5. Press OK to confirm and perform the operations as de-
s • press the main switch (A22) (fig. 2). scribed in the corresponding sections.
Important!
- 8.3 Program beverages
Never press the main switch while the appliance is on.
The appliance is set by default to automatically deliver standard
8. MENU SETTINGS quantities. To change these quantities and customise the direct-
, ly selected beverages and the (B14), proceed as
The menu has 6 items, some divided into subgroups:
• Language; follows:
• Maintenance: 1. Press (B6) to enter the "Settings" menu;
- Descale, 2. Press the selection arrows (B2 and B4) until "Prg. beverag-
- Install filter, es" is displayed between the two lines;
h - (if a filter has been installed): Replace filter, 3. Press OK (B3) to confirm: the appliance lists the beverages
- (if a filter has been installed): Remove filter; you can customise;
• Prg. beverages; 4. Press the selection arrows until the beverage you want to
c • Prg. my beverages; customise is displayed, then press OK to confirm;
- • General: 5. Beverages with coffee: "Program aroma" appears on
- Set temperature, the display: press the selection arrows (B2 and B4) or
- Water hardness, (B7) until the required aroma is selected (see section “10.4
- Auto-off, Temporarily varying the coffee aroma”), then press OK.
d - Energy saving, "Program coffee" appears on the display together with a
- Beep, bar which gradually fills as delivery progresses. When the
- Default beverages, required quantity is reached, press OK;
- Default values; Cappuccinos and milk-based coffees: after selecting
. • Statistics.
- the aroma, "Program milk" appears on the display togeth-
er with a bar which gradually fills as milk delivery pro-
8.1 Language gresses. When the required quantity is reached, press OK.
To modify the language of the display (B1), proceed as follows: The appliance then makes the coffee. Press OK to interrupt
s
1. Press (B6) to enter the "Settings" menu; delivery when the required quantity of coffee is reached.
l
2. Press OK (B3) to select "Language". The available languag- Hot water: press OK. Delivery begins: press OK when the
es are displayed; required quantity is reached.
3. Press the selection arrows (B2 and B4) until the required 6. "Save parameters?": to save the settings, press OK (other-
language is displayed between the two lines; wise press /ESC - B2 or B5).
4. Press OK to confirm; 7. "Parameters saved" (or "Parameters not saved"). The ap-
5. The appliance goes back to the "Settings" menu; pliance is ready for use again.
6. Press /ESC (B5) to exit the menu.
8.4 Program My beverages
8.2 Maintenance Follow the procedures described in the previous section “8.3 Pro-
s Here you can find all the maintenance operations required by gram beverages”to customise the beverages in the "
the appliance over time: " (B14) or proceed with direct programming, as described in
. • Descale: For instructions on descaling, see section “15. section “12. “ ” Programming and selecting”.
Descaling”.
• Install filter: For instructions on how to install the filter 8.5 General
(C4), see section “17.1 Installing the filter”. Here you can find the settings to customise the basic functions
To select the operation you require, proceed as follows: of the appliance:
1. Press (B6) to enter the "Settings" menu;
11
1. Press (B6) to enter the "Settings" menu; • Beep:
2. Press the selection arrows (B2 and B4) until "General" is Use this function to enable or disable the beep. Proceed as
displayed between the two lines; follows:
3. Press OK (B3) to confirm and select the required item with 4. Press OK. The current state ("Enabled" or "Disabled") and
the selection arrows. Then follow the instructions for each the operation to be performed ("Disable?" or "Enable?") is
setting. displayed. Press OK to confirm;
5. Press OK to disable or enable the function.
• Set temperature: The display goes back to the previous screen.
To modify the temperature of the water used to make the coffee,
proceed as follows: • Default beverages:
4. Press OK (B3). The current value appears on the display Use this function to reset the default values for all the beverag-
(B1) and the "New" value flashes; es, or the individual beverages programmed previously. Select
5. Select the new value you want to set using the selection the beverage, then proceed as follows:
arrows (B2 or B4); 4. Select "All" to reset the aroma and quantity settings to the
6. When the required value (low, medium, high, maximum) default values, or select the required beverage, then press
has been selected, press OK. OK;
The display goes back to the previous screen. 5. "Reset?": to reset the default values, press OK.
6. "Reset complete": the appliance confirms the reset and
• Water hardness: goes back to the previous screen.
For instructions on identifying and setting water hardness, see To reset another beverage, repeat from point 4 or to exit, press
section “16. Setting water hardness”. /ESC (B5).
• Auto-off (standby): • Default values:
Auto-off can be set so that the appliance goes off after 15 or 30 Use this function to reset all the appliance and beverage settings
minutes, or 1, 2 or 3 hours (apart from the language which remains as selected the first
4. Press OK. The current value appears on the display (B1) and time the appliance was used). Select the item, then proceed
the "New" value flashes; as follows:
5. Select the new value you want to set using the selection 4. "Reset?"; press OK;
arrows (B2 or B4); 5. "Reset complete": the appliance confirms the reset and
6. When the required value (low, medium, high, maximum) goes back to the previous screen.
has been selected, press OK. To exit, press /ESC (B5).
The display goes back to the previous screen.
• Energy saving: 8.6 Statistics
Use this function to enable or disable energy saving. When en- This displays statistics relating to the machine. To display the
abled, the function reduces energy consumption in compliance statistics, proceed as follows:
with European regulations. 1. Press (B6) to enter the "Settings" menu;
To disable or enable "Energy Saving", proceed as follows: 2. Press the selection arrows (B2 and B4) until "Statistics" is
4. Press OK. The current state ("Enabled" or "Disabled") and displayed between the two lines;
the operation to be performed ("Disable?" or "Enable?") is 3. Press OK (B3): statistics on the appliance are displayed, use
displayed. Press OK to confirm; the selection arrows to scroll through the items;
5. Press OK to disable or enable the function. 4. Press /ESC (B5) to exit.
The display goes back to the previous screen. To go back to the main screen, press /ESC.
Please note!
• when the function is enabled, the symbol "E" appears on 9. RINSING
the display. Use this function to deliver hot water from the coffee spouts
• When in energy saving mode, a few seconds elapse before (A9) and hot water spout (C6), if inserted, to clean and heat the
the first coffee, cappuccino or milk-based coffee is deliv- appliance’s internal circuit.
ered as the appliance must heat up again. Place a container with a minimum capacity of 100ml under the
• If the milk container (D) is inserted, "Energy Saving" can- coffee and hot water spouts.
not be activated.
Important! Danger of burns.

12
 Do not leave the appliance unattended while hot water is being 10.3 Making automatic recipes using coffee
s delivered. beans
d 1) To enable this function, press (B5). "RINSING" appears Important!
on the display (B1); Do not use green, caramelised or candied coffee beans as they
2) After a few seconds, hot water is delivered first from the could stick to the coffee mill and make it unusable.
coffee spouts, then from the hot water spout (if inserted) 1. Fill the container (A3) (fig. 8) with coffee beans;
to clean and heat the appliance’s internal circuit. A progress 2. Place under the coffee spouts (A9):
bar is displayed and fills gradually as preparation proceeds; - 1 cup, if you want to make 1 coffee (fig. 9);
3) To interrupt, press the arrow corresponding to "STOP" (B4). - 2 cups if you want 2 coffees.
- 3. Lower the spouts as near as possible to the cup. This makes
Please note! a creamier coffee (fig. 10);
• If the appliance is not used for more than 3-4 days, when 4. Then select your required coffee:
e switched on again, we strongly recommend performing
s 2/3 rinses before use; Directly selected beverages
• After cleaning, it is normal for the coffee grounds container Recipe Quantity Program- Default
(A11) to contain water. mable aroma
quantity
10. MAKING COFFEE ≃ 40 ml from ≃30
s 10.1 Adjusting the coffee mill Espresso (B8) to ≃ 80ml
The coffee mill is set by default to prepare coffee correctly and
≃ 180 ml from ≃100
should not require regulating initially.
Coffee (B9) to ≃240cc
However, if after making the first few coffees you find that the
t coffee is either too weak and not creamy enough or delivery is ≃ 175 ml from ≃115 +
too slow (a drop at a time), this can be corrected by adjusting Long (B10) to ≃250cc
the grinding dial (A5) (fig. 7). +
Beverages with coffee selectable from the
Please note: (B14)
The grinding adjustment dial must only be turned when the Long Espresso ≃ 120 ml from ≃80 +
coffee mill is in operation. to ≃180c
If the coffee is delivered too slowly or not
at all, turn one click clockwise towards 7.
Short ≃ 30 ml from ≃20
For fuller bodied creamier coffee, turn to ≃40cc
one click anticlockwise towards 1 (do not Doppio+ ≃ 120 ml from ≃80 ++
turn more than one click at a time other- to ≃180cc
wise the coffee could be delivered a drop 2 Espresso ≃ 40 ml x -- +
s at a time). 2 cups
These adjustments will only be evident after at least 2 cups of
e coffee have been delivered. If this adjustment does not obtain 2 Long ≃ 120 ml --
the desired result, turn the dial another click. Espresso x 2 cups
2 Short ≃ 30 ml x -- +
10.2 Tips for a hotter coffee Espresso 2 cups
For hotter coffee, you should: +
• to rinse, press /ESC (B5); 5. Preparation begins. A progress bar appears on the display
• warm the cups with hot water using the hot water function (B1) and gradually fills as preparation proceeds.
(see section “13. Delivering hot water”); +
• increase the coffee temperature in the "Settings" menu
e Please note:
(see section “8.5 General”).
• You can prepare 2 cups of SHORT ESPRESSO, ESPRESSO or
LONG ESPRESSO coffee at the same time by pressing "2X"
(B3) during preparation of single beverages (the image is
displayed for a few seconds at the start of preparation).
13
• While the machine is making coffee, delivery can be inter- 10.5 Making coffee using pre-ground coffee
rupted at any time by pressing the selection arrow corre-
Important!
sponding to "STOP" (B4).
• Never add pre-ground coffee when the machine is off or it
• At the end of delivery, to increase the quantity of coffee in
could spread through the inside of the machine and dirty
the cup, just press and hold (within 3 seconds) one of the
it. This could damage the appliance.
coffee buttons (B8 or B10).
• Never use more than 1 level measure (C2) or it could dirty
Once the coffee has been made, the appliance is ready to make
the inside of the coffee machine or block the funnel (A4).
the next beverage.
Please note:
Please note:
If you use pre-ground coffee, you can only make one cup of
• Various alarm messages could be displayed while using the
coffee at a time.
appliance (fill tank, empty grounds container, etc.). Their
meaning is explained in section “20. Displayed messages”.
1. Press the button (B7) repeatedly until " " ap-
• For hotter coffee, see section “10.2 Tips for a hotter coffee”.
pears on the display (B1).
• If the coffee is delivered a drop at a time, too weak and not
2. Make sure the funnel is not blocked, then add one level
creamy enough or too cold, read the tips in section “21.
measure of pre-ground coffee (fig. 11).
Troubleshooting”.
3. Place a cup under the coffee spouts (A9) (fig. 9).
• To customise the beverages according to personal taste,
4. Then select your required coffee:
see sections “8.3 Program beverages” and “8.4 Program My
beverages”. Directly selected beverages
Recipe Quantity
10.4 Temporarily varying the coffee aroma
Espresso (B8) ≃ 40 ml
To temporarily vary the aroma of the coffee in the automatic
recipes, press (B7): Coffee (B9) ≃ 180 ml
Custom (if programmed) / Long (B10) ≃ 175 ml
AUTO
Standard
Beverages with coffee selectable from the
EXTRA LIGHT (B14)
Long Espresso ≃ 120 ml
LIGHT
Short ≃ 30 ml
MEDIUM 5. Preparation begins. The beverage selected appears on the
+ display together with a progress bar which gradually fills
STRONG as preparation proceeds.

+
+ X-STRONG
+
+
Important! Making LONG coffee :
+ (see “10.5 Making coffee Halfway through preparation, the message "Add pre-ground
using pre-ground coffee”) coffee" appears on the display (B1). Add one level measure of
pre-ground coffee and press OK (B3).

Please note: Please note:

• The variation in aroma is not saved and the next time a
beverage is delivered automatically, the appliance selects If "Energy Saving" mode is active, you may have to wait a few
the default value ( AUTO). seconds before the first coffee is delivered.
• If a few seconds elapse between temporary customising of
the aroma and delivery of the beverage, the aroma returns 11. MAKING CAPPUCCINOS AND MILK-BASED
to the default value ( AUTO). COFFEES
Please note: 1
• To avoid milk with poor froth or large bubbles, always
+ clean the milk container lid (D2) and hot water connection 1
14
+
 nozzle (A8) as described in sections “11.4 Cleaning the milk 2. Select the required beverage:
container after use”, “14.10 Cleaning the milk container” Directly selected beverages:
and “14.11 Cleaning the hot water nozzle”. • : CAPPUCCINO (B11)
t
y • : Latte Macchiato (B12)
11.1 Filling and attaching the milk container • : Hot Milk (B13)
y 1. Remove the lid (D2) (fig. 12); Select by pressing (B14):
2. Fill the milk container (D3) with a sufficient quantity of • Cappuccino+
milk, not exceeding the MAX level marked on the handle • Caffelatte
(fig. 13). Each mark on the side of the container corre- • Flat white
f sponds to 100ml of milk; • Espresso macchiato;
Please note: 3. After a few seconds, preparation begins automatically, a
• For a denser more even froth, you must use skimmed or progress bar appears on the display and gradually fills as
- preparation proceeds;
partially skimmed milk at refrigerator temperature (about
5°C). 4. After delivering the milk, the machine automatically
l makes the coffee (if required by the recipe).
• If "Energy Saving" mode is enabled, you may have to wait
a few seconds before the first cappuccino is delivered. Please note:
3. Make sure the milk intake tube (D4) is correctly inserted in • If you want to interrupt preparation during delivery, press
the bottom of the milk container lid (fig. 14); the arrow corresponding to "STOP" (B4).
4. Place the lid back on the milk container; • Do not leave the milk container out of the refrigerator for
5. Remove the hot water spout (C6) from the connection noz- long periods. The warmer the milk (5°C is ideal), the poorer
zle (A8) (fig. 15); the quality of froth produced.
6. Attach the container to the connection nozzle and push • The beverages can be customised (see sections “8.3 Pro-
as far as it will go (fig. 16). The machine emits a beep (if gram beverages” and “8.4 Program My beverages”).
enabled);
7. Place a sufficiently large cup under the coffee spouts (A9) 11.4 Cleaning the milk container after use
and frothed milk spout (D5). Adjust the length of the milk Important! Danger of burns
spout. To move it nearer the cup, simply pull it downwards • When cleaning the internal tubes of the milk container (D),
(fig. 17); a little hot water and steam leak out of the milk spout (D5).
8. Follow the instructions below for each function. Avoid contact with splashes of water.
e "Set dial to CLEAN, ESC to cancel" appears on the display (B1)
s 11.2 Adjusting the amount of froth each time you use a milk function. Clean as described to elim-
Turn the froth adjustment dial (D1) to adjust the amount of froth inate all milk residues (or press “ /ESC” (B5) to clean later):
on the milk delivered while making cappuccinos and milk-based 1. Leave the milk container (D) in the machine (you do not
coffees. need to empty it);
Dial Description Recommended for… 2. Place a cup or other recipient under the frothed milk spout;
d
position 3. Turn the froth adjustment dial (D1) to “CLEAN” (fig. 19).
f
“Cleaning underway” appears on the display, together
No froth HOT MILK (not frothed) /
with a progress bar which gradually fills as the operation
CAFFELATTE
proceeds. Cleaning stops automatically;
Min. froth LATTE MACCHIATO / 4. Turn the dial back to one of the froth selections;
w FLAT WHITE 5. Remove the milk container and always clean the steam
connection nozzle (A8) with a sponge (fig. 20).
Max. froth CAPPUCCINO/ CAPPUCCI-
NO+ / ESPRESSO MACCHIA-
TO / HOT MILK (frothed) Please note!
• To prepare a number of cappuccinos or milk-based coffees,
11.3 Making cappuccino and milk-based coffees clean the milk container after you have prepared the last
s automatically beverage only. In this case, press /ESC (B5) to go back to
1. Fill the milk container (D) and attach it as described above; the main menu.

15
• The milk container can be kept in the refrigerator. 4. Press OK (B3). A progress bar appears and gradually fills as
• In some cases, before cleaning you must wait for the appli- preparation proceeds;
ance to heat up. 5. The machine delivers about 250 ml of hot water, then
delivery stops automatically. To interrupt hot water deliv-
12. “ ” PROGRAMMING AND SELECTING ery manually, press the selection arrow corresponding to
In you can select beverages customised to your per- "STOP" (B4) again.
sonal tastes. If the beverages have not yet been programmed, Please note:
the appliance will request the customisation procedure before • If "Energy Saving" mode is active, you may have to wait a
proceeding with delivery: few seconds before hot water is delivered.
1. Press (B15); • The quantity of water delivered can be customised (see
2. Press the selection arrows (B2 and B4) until the required section “8.3 Program beverages”).
beverage is displayed between the two lines;
Unprogrammed beverages: 14. CLEANING
3. Press OK (B3) to select;
14.1 Cleaning the machine
4. Beverages with coffee: "Program aroma" appears
The following parts of the machine must be cleaned regularly:
on the display. Press the selection arrows (B2 and B4) or
- the appliance’s internal circuit;
(B7) until the required aroma is selected. Press OK.
- coffee grounds container (A11);
"Program coffee" appears on the display together with a
- drip tray (A15) and condensate tray (A10);
bar which gradually fills as delivery progresses. When the
- water tank (A17);
required quantity is reached, press OK.
5. Cappuccinos and milk-based coffees: After select- - coffee spouts (A9);
ing the aroma, "Program milk" appears on the display - pre-ground coffee funnel (A4);
together with a bar which gradually fills as milk delivery - infuser (A20), accessible after opening the infuser door
progresses. When the required quantity is reached, press (A19);
OK. - milk container (D);
6. The appliance then makes the coffee. Press OK to interrupt - hot water/steam connection nozzle (A8);
delivery when the required quantity of coffee is reached. Important!
7. "Save parameters?": to save the settings, press OK (other- • Do not use solvents, abrasive detergents or alcohol to clean
wise press ESC - B2 or B5). the coffee machine. With De’Longhi superautomatic coffee
8. "Parameters saved" (or "Parameters not saved"). The ap- machines, you need not use chemical products to clean the
pliance is ready for use again. machine.
Programmed beverages: • None of the components of the appliance can be washed
3. Press OK (B3) to select; in a dishwasher with the exception of the drip tray grille
4. Preparation begins according to the previously pro- (A14) and milk container (D).
grammed settings. • Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Please note:
Two cups of a beverage can only be selected when the corre- 14.2 Cleaning the machine's internal circuit
sponding single beverages have been programmed. If the appliance is not used for more than 3/4 days, before using
it again, we strongly recommend switching it on and:
- performing 2/3 rinse cycles by pressing (B5);
13. DELIVERING HOT WATER - delivering hot water for a few seconds (section “13. Deliv-
ering hot water”).
Important! Danger of burns.
Never leave the machine unattended while delivering hot water. Please note:
1. Make sure the hot water spout (C6) is attached correctly; After cleaning, it is normal for the coffee grounds container
2. Place a container under the water spout (as close as possi- (A11) to contain water.
ble to avoid splashes) (fig. 5);
3. Press (B14) and scroll through the beverages
in the menu by pressing the selection arrows (B2 or B4)
until "Hot water" is selected;
16
s 14.3 Cleaning the coffee grounds container 14.5 Cleaning the inside of the coffee machine
When "Empty grounds container" appears on the display (B1),
Danger of electric shock!
n the grounds container must be emptied and cleaned. The ap-
Before cleaning internal parts, the machine must be turned off
- pliance cannot be used to make coffee until you have cleaned
(see section “7. Turning the appliance off”) and unplugged from
o the grounds container (A11). Even if not full, the empty grounds
the mains power supply. Never immerse the coffee machine in
container message appears on the display 72 hours after the
water.
first coffee has been prepared. For the 72 hours to be calculated
a correctly, the machine must never be turned off with the main
1. Check regularly (about once a month) that the inside of
switch (A22).
the appliance (accessible after removing the drip tray, A15)
e Important! Danger of burns is not dirty. If necessary, remove coffee deposits with the
If you make a number of cappuccinos one after the other, the brush (C5) supplied and a sponge;
metal cup tray (A12) becomes hot. Wait for it to cool down be- 2. Remove all the residues with a vacuum cleaner (fig. 23).
fore touching it and handle it from the front only.
14.6 Cleaning the water tank
To clean (with the machine on): 1. Clean the water tank (A17) regularly (about once a month)
• Remove the drip tray (A15) (fig. 21), empty and clean. and whenever you replace the water softener filter (C4) (if
• Empty the grounds container (A11) and clean thoroughly provided) with a damp cloth and a little mild washing up
to remove all residues left on the bottom. This can be done liquid;
with the spatula on the brush (C5) provided. 2. Remove the filter (C4) (if present) and rinse with running
• Check the condensate tray (A10) (red) and empty if water;
necessary. 3. Replace the filter (if provided), fill the tank with fresh
r Important! water and replace the tank;
When removing the drip tray, the grounds container must be 4. (Models with water softener filter only) Deliver about
emptied, even if it contains few grounds. 100ml of water.
If this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine. 14.7 Cleaning the coffee spouts
1. Clean the coffee spouts (A9) regularly with a sponge or
14.4 Cleaning the drip tray and condensate tray cloth (fig. 24A);
e 2. Check that the holes in the coffee spouts are not blocked.
Important! If necessary, remove coffee deposits with a toothpick (fig.
The drip tray (A15) is fitted with a level indicator (A13) (red) 24B).
showing the level of water it contains (fig. 22). Before the in-
dicator protrudes from the cup tray (A12), the drip tray must 14.8 Cleaning the pre-ground coffee funnel
be emptied and cleaned otherwise the water may overflow the Check regularly (about once a month) that the pre-ground
e
edge and damage the appliance, the surface it rests on or the coffee funnel (A4) is not blocked. If necessary, remove coffee
surrounding area. deposits with the brush (C5) supplied.
To remove the drip tray:
1. Remove the drip tray and the coffee grounds container
g 14.9 Cleaning the infuser
(A11) (fig. 21);
The infuser (A20) must be cleaned at least once a month.
2. Remove the cup tray (A12) and drip tray grille (A14), then
empty the drip tray and grounds container and wash all Important!
- components; The infuser may not be extracted when the machine is on.
3. Check the red condensate tray (A10) and empty if 1. Make sure the machine is correctly turned off (see “7. Turn-
necessary; ing the appliance off”);
r 4. Replace the drip tray complete with grille and grounds 2. Remove the water tank (A17);
container. 3. Open the infuser door (A19) (fig. 25) on the right side of
the appliance;
4. Press the two coloured release buttons inwards and at the
same time pull the infuser outwards (fig. 26);

17
5. Soak the infuser in water for about 5 minutes, then rinse 15. DESCALING
under the tap;
Important!
Important! • Before use, read the instructions and the labelling on the
RINSE WITH WATER ONLY descaler pack.
NO WASHING UP LIQUID - NO DISH WASHER • You should use De’Longhi descaler only. Using unsuitable
Clean the infuser without using washing up liquid as it descaler and/or performing descaling incorrectly may re-
could be damaged. sult in faults not covered by the manufacturer's guarantee.
6. Use the brush (C5) to remove any coffee residues left in the Descale the machine when "Descale, ESC to cancel, OK to des-
infuser housing, visible through the infuser door; cale (∼45 minutes)" appears on the display (B1). To descale im-
7. After cleaning, replace the infuser by sliding it onto the in- mediately, press OK (B3) and follow the instructions from point
ternal support, then push the PUSH symbol fully in until it 6. To descale the appliance later, press ESC (B5). The symbol
clicks into place; on the display reminds you that the appliance needs descaling.
Please note: To access the descaling menu:
If the infuser is difficult to insert, before insertion, adapt it to the 1. Turn the appliance on and wait until it is ready for use;
right size by pressing the two levers (fig. 27). 2. Press (B6) to enter the "Settings" menu;
8. Once inserted, make sure the two coloured buttons have 3. Press the selection arrows (B2 and B4) until "Maintenance"
snapped out; is displayed between the two lines. Press OK (B3);
9. Close the infuser door; 4. Press OK to select "Descale";
10. Put the water tank back. 5. Confirm? (∼45 minutes)”. Press OK to confirm;
6. "Remove filter": extract the water tank (A17), remove the
14.10 Cleaning the milk container water softener filter (C4) (if present) and empty the water
Clean the milk container (D) each time you prepare milk as de- tank. Press OK;
scribed below: 7. "Pour descaler and water into tank": Pour the descaler into
1. Remove the lid (D2); the tank up to level A (corresponding to a 100 ml pack)
2. Remove the milk spout (D5) and intake tube (D4) (fig. 28); marked on the inner surface of the tank, then add water
3. Turn the froth adjustment dial (D1) anticlockwise to the (1 litre) up to level B (fig. 32) and put the water tank back.
"INSERT" position (fig. 29) and pull off upwards; Press OK;
4. Wash all the components thoroughly with hot water and 8. "Empty drip tray": Remove, empty and replace the drip
mild washing-up liquid. All components are dishwasher tray (A15) and grounds container (A11). Press OK;
safe, placing them in the top basket of the dishwasher. 9. "Place 1.8L container empty under spouts": Place an empty
Make sure there are no milk residues on the hollow and container with a minimum capacity of 1.8 litres under the hot
groove under the dial (fig. 30). If necessary, scrape the water spout (C6) and coffee spouts (A9) (fig. 33). Press OK;
groove with a toothpick;
5. Rinse inside the froth adjustment dial seat with running Important! Danger
water (fig. 31); of burns
6. Check that the intake tube and milk spout are not clogged Hot water containing acid
with milk residues; flows out of the coffee spouts
7. Replace the dial (in correspondence to the word "INSERT"), and hot water spout. Take
spout and milk intake tube; care to avoid contact with
8. Place the lid back on the milk container (D3). splashes of this solution.

1,8 l
14.11 Cleaning the hot water nozzle 10. "Descaling underway":
Each time you prepare milk, clean the connection nozzle (A8) The descale programme
with a sponge to remove milk residues from the gaskets (fig. starts and the descaler liq-
20). 33 uid comes out of the hot
water and coffee spouts. A series of rinses and pauses is
performed automatically to remove all the scale residues
inside the coffee machine;
After about 25 minutes, descaling stops;

18
 11. "Rinse tank and fill with water": the appliance is now 16. SETTING WATER HARDNESS
ready to rinse with fresh water. Empty the container used The descale message is displayed after a period of time estab-
to collect the descaler solution. Extract the water tank, lished according to water hardness.
e
empty, rinse under running water, fill with fresh water up The machine is set by default for a hardness level of 4. The ma-
to the MAX level and put back in the appliance. Press OK; chine can also be programmed according to the hardness of the
12. "Place 1.8L container empty under spouts": place the con- mains water in the various regions so that the machine needs to
-
tainer used to collect the descaler solution empty under be descaled less often.
.
the coffee spouts and hot water spout (fig. 33) and press
-
OK"; 16.1 Measuring water hardness
-
13. "Rinsing Confirm?": press OK; 1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
t
11. "Rinsing underway": hot water is delivered first from the from its pack (attached to the English instructions);
l coffee spouts, then from the hot water spout; 2. Immerse the paper completely in a glass of water for one
12. When the water in the tank has run out, empty the con- second;
tainer used to collect the rinsing water; 3. Remove the paper from the water and shake lightly. After
13. "Rinse tank and fill with water": extract the water tank and about a minute, 1, 2, 3, or 4 red squares form, depending
fill with fresh water up to the MAX level. Press OK; on the hardness of the water. Each square corresponds to
" 14. "Insert filter": put the water softener filter (if removed) one level;
back in its housing in the water tank, and replace the tank
in the appliance. Press OK; soft water (level 1)
15. "Place 1.8L container empty under spouts": place the con-
tainer used to collect the descaler solution empty under
r slightly hard water (level 2)
the hot water spout. Press OK;
16. "Rinsing Confirm?": press OK.
hard water (level 3)
17. "Rinsing underway". Hot water comes out of the hot water
spout;
very hard water (level 4)
18. "Empty drip tray": At the end of the second rinse, remove,
empty and replace the drip tray (A15) and grounds con-
tainer (A11). Press OK; 16.2 Setting water hardness
p 19. "Descale complete": press OK; 1. Press (B6) to enter the "Settings" menu;
20. "Fill tank": empty the container used to collect the rinse 2. Press the selection arrows (B2 and B4) until "General" is
water, remove the water tank and fill with fresh water up displayed between the two lines. Press OK;
t to the MAX level, then put back in the appliance. 3. Press the selection arrows until "Water hardness" is dis-
Descaling is complete. played, then press OK;
4. The current selection appears on the display and the new
Please note! selection flashes. Press the selection arrows until the re-
• If the descaling cycle is not completed correctly (e.g. no quired new selection is displayed. Press OK.
electricity) we recommend repeating the cycle; The new level is saved and the appliance goes back to the "Gen-
s eral" menu.
e • After descaling, it is normal for the grounds container
(A11) to contain water; Press /ESC (B5) twice to go back to the main screen.
h
• If the water tank has not been filled to the MAX level, at
the end of descaling, the appliance requests a third rinse to 17. WATER SOFTENER FILTER
guarantee that the descaler solution has been completely Certain models are fitted with a water softener filter (C4). If this
:
eliminated from the machine's internal circuits. is not the case with your model, you are recommended to pur-
e
• The appliance may request descaling cycles at very short chase one from De’Longhi Customer Services.
-
intervals. This is normal and due to the appliance’s ad- To use the filter correctly, follow the instructions below.
t
s vanced control system.

19
17.1 Installing the filter
1. Remove the filter (C4)
from the packaging. The
date indicator disk varies
according to the filter
provided.
2. Turn the date indicator
34 disk (fig. 34) until the
next 2 months of use are
displayed.
Please note
The filter lasts about two 37 38
months if the appliance is When you install the filter, you must notify the appliance of its
used normally. If the coffee presence.
machine is left unused with the filter installed, it will last a max- 8. Press (B6) to enter the "Settings" menu;
imum of three weeks. 9. Press the selection arrows (B2 and B4) until "Maintenance"
3. To activate the filter, run tap water through the hole in the is displayed between the two lines. Press OK;
filter as shown in fig. 35 until water comes out of the open- 10. Press the selection arrows until "Install filter" is displayed,
ings at the side for more than a minute.; then press OK;
11. Confirm?": press OK;
12. "Hot water, Confirm?": Position a container under the hot
0,5 L water spout (C6) (min. capacity: 500 ml), then press OK;
13. The appliance begins hot water delivery and the message
"Please wait" is displayed;
14. After the flow of hot water stops, the appliance automati-
cally resets to "Ready for coffee" status.
The filter is now active and you can use the coffee machine.

17.2 Replacing the filter

Replace the filter (C4) when "Replace filter, ESC to cancel, OK to
35 36 replace" appears on the display (B1). To replace immediately,
4. Extract the tank (A17) from the appliance and fill with press OK (B3) and follow the instructions from point 8. To re-
water; place later, press ESC (B5). The symbol on the display reminds
5. Insert the filter in the water tank and immerse it complete- you that the filter needs replacing.
ly for about ten seconds, sloping it and pressing it lightly to To replace the filter, proceed as follows:
enable the air bubbles to escape (fig. 36). 1. Extract the tank (A17) and exhausted filter;
6. Insert the filter in the filter housing (A18) and press as far 2. Take the new filter out of its packet and proceed as illus-
as it will go (fig. 37); trated in points 2, 3, 4, 5, 6 and 7 in the previous section;
7. Close the tank with the lid (A16) (fig. 38), then replace the 3. Press (B6) to enter the "Settings" menu;
tank in the machine; 4. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press OK;
5. Press the selection arrows until "Replace filter" is dis-
played, then press OK;
6. Confirm?": press OK;
7. "Hot water, Confirm?": Position a container under the hot
water spout (C6) (min. capacity: 500 ml), then press OK;
8. The appliance begins hot water delivery and the message
"Please wait" is displayed;

20
 9. After the flow of hot water stops, the appliance automati- 18. TECHNICAL DATA
cally resets to "Ready for coffee" status. Voltage: 220-240 V~ 50/60 Hz max. 10A
The new filter is now active and you can use the coffee machine. Absorbed power: 1450W
Please note! Pressure: 1.5MPa (15 bars)
After two months (see date indicator) or when the appliance has Max. water tank capacity: 1.8 l
not been used for 3 weeks, you should replace the filter even if Size LxDxH: 240x440x360 mm
the message has not yet been displayed. Cord length: 1750 mm
Weight: 9.9 kg
17.3 Removing the filter Max. beans container capacity: 300 g
If you want to use the appliance without the filter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows: The appliance complies with the following EC
1. Extract the tank (A17) and exhausted filter; directives:
2. Press (B6) to enter the "Settings" menu;
• EMC Directive 2004/108/EC and subsequent amendments;
3. Press the selection arrows (B2 and B4) until "Maintenance"
• Materials and accessories coming into contact with food
" is displayed between the two lines. Press OK;
conform to EEC regulation 1935/2004.
4. Press the selection arrows until "Remove filter" is dis-
, played, then press OK;
19. DISPOSING OF THE APPLIANCE
5. "Confirm?": press OK to confirm removal. The appliance
The appliance must not be disposed of with house-
goes back to the "Maintenance" menu;
hold waste, but taken to an authorised waste separa-
Press /ESC (B5) to exit the menu.
tion and recycling centre.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
- the message has not yet been displayed.

20. DISPLAYED MESSAGES

o DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

,
- Fill tank Insufficient water in the tank (A17). Fill the tank with water and/or insert it correct-
ly, pushing it as far as it will go until it clicks
s
into place (fig. 3B).
Insert tank The tank (A17) is not correctly in place. Insert the tank correctly and press as far as it
will go (page 3B).
- Empty grounds container The grounds container (A11) is full. Empty the grounds container and drip tray
(A15), clean and replace. Important: when
removing the drip tray, the grounds contain-
" er MUST be emptied, even if it contains few
grounds. If this is not done, when you make
- the next coffees, the grounds container may fill
up more than expected and clog the machine.
Insert grounds container After cleaning, the grounds container (A11) Remove the drip tray (A15) and insert the
has not been replaced. grounds container.

21
Add pre-ground coffee The "pre-ground coffee" function has been se- Place pre-ground coffee in the funnel (fig. 11)
lected without placing any pre-ground coffee or deselect the "pre-ground" function.
in the funnel (A4).
A LONG coffee with pre-ground coffee has Put one level measure of pre-ground cof-
been requested fee into the pre-ground coffee funnel (A4)
and press OK (B3) to continue and complete
preparation.
Fill beans container The coffee beans have run out. Fill the beans container (A3) (fig. 8).

The pre-ground coffee funnel (A4) is clogged. Empty the funnel with the help of the brush
(C5) as described in section “14.8 Cleaning the
pre-ground coffee funnel”.
Ground too fine The grinding is too fine and the coffee is deliv- Repeat coffee delivery and turn the grinding
Adjust mill ered too slowly or not at all. adjustment dial (A5) (fig. 7) one click clockwise
towards 7 while the coffee mill is in operation.
If after making at least 2 coffees delivery is
still too slow, repeat the correction procedure,
turning the grinding adjustment dial another
click until delivery is correct (see section “10.1
Adjusting the coffee mill”. If the problem per-
sists, make sure the water tank (A17) is fully
inserted.
If the water softener filter (C4) is present, an Insert the hot water spout (C6) in the appli-
air bubble may have been released inside the ance and deliver a little water until the flow
circuit, obstructing delivery. becomes regular.
Less coffee Too much coffee has been used. Select a lighter taste by pressing (B7) or
reduce the quantity of pre-ground coffee.
Insert water spout The hot water spout (C6) is not inserted or is Fully insert the hot water spout (fig. 4).
inserted incorrectly.
Insert milk container The milk container (D) is not inserted correctly. Insert the milk container as far as it will go (fig.
16).
Insert infuser assembly The infuser (A20) has not been replaced after Insert the infuser as described in section “14.9
cleaning. Cleaning the infuser”.
Water circuit empty The water circuit is empty. Press OK (B3) to deliver water from the spout
Fill water circuit (C6) until it flows out normally. If the problem
Hot water persists, make sure the water tank (A17) is fully
Confirm?
inserted.
Press OK to CLEAN The milk container (D) has been inserted with To proceed with the CLEAN function press OK
the froth adjustment dial (D1) in the "CLEAN" or turn the froth adjustment dial to another
position. position.
Set dial to CLEAN Milk has been delivered recently and the tubes Turn the froth adjustment dial (D1) to CLEAN
ESC to cancel inside the milk container (D) must be cleaned. (fig. 19).
Turn froth adjustment dial The milk container (D) has been inserted with Turn the froth adjustment dial to one of the
the froth adjustment dial (D1) in the "CLEAN" milk froth positions.
position.

22
Descale The machine must be descaled. The descaling procedure described in section
ESC to cancel “15. Descaling” needs to be performed.
OK to descale
(∼45 minutes)
Replace filter The water softener filter (C4) is exhausted. Replace the filter or remove it as described in
ESC to cancel section “17. Water softener filter”.
OK to replace
General alarm The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,
as described in section “14. Cleaning”. If the
message is still displayed after cleaning, con-
tact a service centre.
The tubes inside the milk container (D) must Turn the froth adjustment dial (D1) to CLEAN
be cleaned. (fig. 19).
The water softener filter (C4) is exhausted and Replace the filter or remove it as described in
must be replaced or removed. section “17. Water softener filter”.

The machine must be descaled. The descaling procedure described in section

“15. Descaling” needs to be performed.
The appliance may request descaling cycles at
very short intervals. This is normal and due to
the appliance’s advanced control system.

E Energy saving is enabled. To disable energy saving, proceed as described

in section “8.5 General” - “•Energy saving:”

23
21. TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.

PROBLEM POSSIBLE CAUSE REMEDY

The coffee is not hot. The cups were not preheated. Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The internal circuits of the appliance have Before making coffee, rinse the internal circuits
cooled down because 2/3 minutes have by pressing the button (B5).
elapsed since the last coffee was made.
A low coffee temperature is set. Set a higher coffee temperature in the menu.

The coffee is weak or not The coffee is ground too coarsely. Turn the grinding adjustment dial (A5) one
creamy enough. click anticlockwise towards 1 while the coffee
mill is in operation (fig. 7). Continue one click
at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2
coffees (see section “10.1 Adjusting the coffee
mill”).
The coffee is unsuitable. Use pre-ground coffee for espresso machines.

The coffee is delivered too The coffee is ground too finely. Turn the grinding adjustment dial (A5) one
slowly or a drop at a time. click clockwise towards 7 while the coffee mill
is in operation (fig. 7). Continue one click at a
time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see section “10.1 Adjusting the coffee mill”).
The appliance will not make The appliance has detected impurities in its Wait for the appliance to be ready for use again
coffee internal circuits. "Please wait" is displayed. and reselect the required beverage. Contact
Customer Services if the problem persists.
Coffee does not come out of The coffee spouts (A9) are blocked. Clean the spouts with a toothpick (fig. 24B).
one or both of the spouts.

The appliance does not come It is not plugged into the mains socket. Plug into the mains socket (fig. 1).
on
The main switch (A22) is not turned on. Place the main switch in the I position (fig. 2).

The power cord (C7) connector is not inserted Insert the connector as far as it will go in the
correctly. socket at the back of the appliance (fig. 1).
The infuser cannot be The appliance has not been turned off correctly Turn the appliance off by pressing the
extracted button (A7) (fig. 6) (see section “7. Turning the
appliance off”).

24
At the end of descaling, the During the two rinse cycles, the water tank has Follow the instructions displayed by the appli-
appliance requests a third not been filled to the MAX level. ance, but first empty the drip tray to avoid the
rinse water overflowing.
The milk does not come out of The lid (D2) of the milk container lid is dirty Clean the milk container lid as described in the
the milk spout (D5) section “15. Descaling”.
The milk contains large The milk is not cold enough or is not Use skimmed or semi-skimmed milk at refrig-
bubbles and squirts out of semi-skimmed. erator temperature (about 5° C). If the result is
the milk spout (D5) or there is not as you wished, try changing brand of milk.
little froth The froth adjustment dial (D1) is incorrectly Adjust following the instructions in section “
adjusted. • Espresso macchiato;”.
The milk container lid (D2) or froth adjustment Clean the milk container lid and dial as de-
dial (D1) is dirty scribed in section “15. Descaling”.
The hot water connection nozzle (A8) is dirty Clean the connection nozzle as described in
section . “14.11 Cleaning the hot water nozzle”.

25
22. ELECTRICAL REQUIREMENTS
Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you
are in any doubt about your supply contact your local electricity company.
The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity.
Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the proce-
dure outlined below.
Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children
might find it and plug it into a supply socket - with the obvious consequent danger.
Please note: We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in
use.
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code:
Green and Yellow to Earth

GREEN AND YELLOW EARTH 13 amp Fuse

BLUE NEUTRAL
BROWN LIVE
Brown to live
Blue to
neutral Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or
by the earth symbol or coloured green or green and yellow.
- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains
lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified
electrician.
Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should
only be replaced with a flexible cord of the same size.
After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a
replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse
recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover.
Only 13amp replacement fuses which are asta approved to B.S. 1362 should be fitted.
This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.
Warning - this appliance must be earthed

26