Scribd
Upload
74 views1 page

3751

This document provides edits to the AMROFTRP.DAT file to allow it to be used with HP LaserJet III and IV printers. The edits are shown in bold italics. It notes that the file must remain in a single column format for the FAPT Ladder software to work properly. It also provides sample entries for different paper sizes including 10-A, 10-G, 15-G, and 15-A with the appropriate measurements and settings for each.

Uploaded by

rattan singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
74 views1 page

3751

This document provides edits to the AMROFTRP.DAT file to allow it to be used with HP LaserJet III and IV printers. The edits are shown in bold italics. It notes that the file must remain in a single column format for the FAPT Ladder software to work properly. It also provides sample entries for different paper sizes including 10-A, 10-G, 15-G, and 15-A with the appropriate measurements and settings for each.

Uploaded by

rattan singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Edits to FAPT Ladder’s AMROFTRP.

DAT File
For HP LaserJet III and IV Printers

JJD960408
HPLJAMR.DOC

Sample AMROFTRP.DAT file to be used with HPLJ3_4.INF. Changes from the original file that is
provided with the IBM FAPT Ladder software are printed in BOLD-ITALICS. This listing is printed in
columns to allow for single page distribution. An AMROFTRP.DAT file in columns; as shown, may not
work with the FAPT Ladder software. The actual file to be used must remain in a single column, text
format.

NOTE: Some versions of FAPT Ladder do not use the line ANKMODS=2. If your original
AMROFTRP.DAT file does not include this line, and you are downloading AMROFTRP.DAT from our
BBS, use a text editor and delete the ANKMODS=2 line from the downloaded file. If you are editing
your existing file to use HPLJ3_4.INF, do not add ANKMODS=2 to your file.

#PAPER=10-A LINESL=65 LEFTMGL=0


#10-A=10 INCH / ASCII LINES=55 LEFTMG=0
LENGTHL=11 RATIOL=2/3 TOPMGL=0
LENGTH=11 RATIO=2/3 TOPMG=0
WIDTHL=10 GRAMODL=7 LCNTL=4
WIDTH=10 GRAMOD=12 C_FILE=HPLJ3_4.INF
PITCHL=15/120 ANKMODL=0 O_FILE=PRTDAT.DMP
PITCH=20/120 ANKMOD=1 #END
LINESL=65 ANKMODS=2 #15-G=15 INCH / GRAPHIC
LINES=55 LEFTMGL=0 LENGTHL=11
RATIOL=2/3 LEFTMG=0 LENGTH=11
RATIO=2/3 TOPMGL=0 WIDTHL=15
GRAMODL=7 TOPMG=0 WIDTH=15
GRAMOD=12 LCNTL=4 PITCHL=16/120
ANKMODL=0 C_FILE=HPLJ3_4.INF PITCH=20/120
ANKMOD=1 O_FILE=PRTDAT.DMP LINESL=83
ANKMODS=2 #END LINES=55
LEFTMGL=0 #15-A=15 INCH / ASCII RATIOL=2/3
LEFTMG=0 LENGTHL=11 RATIO=2/3
TOPMGL=0 LENGTH=11 GRAMODL=12
TOPMG=0 WIDTHL=15 GRAMOD=12
LCNTL=4 WIDTH=15 ANKMODL=1
C_FILE=HPLJ3_4.INF PITCHL=16/120 ANKMOD=1
O_FILE=PRTDAT.DMP PITCH=20/120 ANKMODS=2
#END LINESL=83 LEFTMGL=0
#10-G=10 INCH / GRAPHIC LINES=55 LEFTMG=0
LENGTHL=11 RATIOL=2/3 TOPMGL=0
LENGTH=11 RATIO=2/3 TOPMG=0
WIDTHL=10 GRAMODL=12 LCNTL=4
WIDTH=10 GRAMOD=12 C_FILE=HPLJ3_4.INF
PITCHL=15/120 ANKMODL=1 O_FILE=PRTDAT.DMP
PITCH=20/120 ANKMOD=1 #END
ANKMODS=2

FANUC CNC Controls


Edits to AMROFTRP.DAT for HP LJ III & IV
Page 1 of 1
GE FANUC AUTOMATION

You might also like