EQUIPMENTS

FOR OIL AND GAS DRILLING RIGS

SC UPETROM - 1 MAI SA
1ST December 1918 Square No. 1
Ploiesti, Prahova County, Romania
Phone: +40 244 501 501
+40 244 501 502
Fax: +40 244 501 503
www.upetrom1mai.com
[email protected]
EQUIPMENTS FOR OIL AND GAS
DRILLING RIGS

DRAWWORKS
The drawworks is an integrant part of the drilling rig and represents the main element of the hoisting system. Depending on its place
of installation (either on the working floor or at a lower level), the drawworks works along with a cathead shaft, a sand drum, a gear box,
a separate or integral rotary table drive unit or it does not include them. If equipped with one or two drums, the drawworks will also be
provided with an auxiliary hydromatic or electromagnetic brake coupled to the drum shaft through a free running coupling; the said
auxiliary brake belongs to the drawworks assembly as well the mechanical one does.
An inertia brake attached to one of the drawworks shaft provides protection to the clutch jaws as well as safe and fast shifting of the jaw
clutches when the speed is shifted. The drawworks assembly is also equipped with an automatic bit feeding device (either pneumatically
or hydraulically operated), a block travel limiter and a grooved wrapper permitting the line to be correctly wound. See the drawworks
specifications as shown below.

Type
Specifications UM
TF-68EU TF55 TF55E TF44 TF44E TF38 TF38E TF25 TF25E TFI20 TFI15
Max. Input power HP 3,500 3,000 3,000 3,000 3,000 2,000 2,300 1,350 1,600 700 400
metric t 62 55 55 44 44 38 38 25 25 20 15
Max. Line pull
ton 68 61 61 49 49 42 42 28 28 22 17
Hoisting speeds - 4 + 4R 4 + 2R 4 + 4R 4 + 2R 4 + 4R 4 + 2R 4 + 2R 2 + 2R 4 + 4R 2 + 1R 2 + 1R
Line size mm 42 38 38 35 35 35 35 32 32 28 25
Aux. Brake type - FE1900 FE1900 FE1900 FH60 FE1700 FH60 FE1400 FH46 FE1400 FH560 FH560
Max. Hoisting speed m/s 20 22 20 22 19.6 22 23 20 20 20 20
Weight kg 50,200 46,600 46,600 35,900 37,790 33,282 32,591 24,000 28,287 8,000 7,500

ROTARY TABLES
UPETROM manufactures the complete range of rotary tables • rotor sealed by labyrinth flanges and geared-shaft sealed
covering the modern drilling requirements; thus, by rubber gaskets;
their opening values range between 17.1/2 in (444.5 mm) • possibility of retrieval for the geared-shaft assembly;
and 49.1/2 in (1,257.3 mm). • dimensions of the square master bushings, square drive
bushings and input-shaft head in accordance with
The main specifications of the UPETROM-made the API Spec.7A requirements;
rotary tables are the following: • axial-radial bearings.
• rectangular-shape cradle simplifying the substructure Opening Static load Input power Max. Speed
design and providing optimum working conditions Type
mton(tf) rpm
in tons HP
on the working floor;
MRL-495 49.1/2 800 880 1,150 250
• chain or cardan-shaft transmission;
• latch mechanism for locking the rotor to the right MRL-375 37.1/2 650 715 600 250
or both directions; MRL-275 27.1/2 500 550 600 300
• splashing lubrication of all bearings and gears; MRL-205 20.1/2 320 350 500 300
• smooth operation of the bevel gearing, whose gears MRS-205 20.1/2 320 350 500 300
are fabricated from superficially heat-treated high-alloyed
MRL-175 17.1/2 250 275 350 300
steels whose quality provides a long operational life;
• efficient sealing to mud and oil; MRS-175 17.1/2 250 275 350 300

DRAWWORKS ROTARY TABLES

 www.upetrom1mai.com

HOOK BLOCKS
Parallel springs to sustain the drill string and make the bolt come out of the box
(the threaded connection is thus protected when the tool joint is broken out); high bearing capacity;
high-capacity sheave bearings having conical rollers to provide the sheaves with the necessary
space for avoiding the use of disks or washers; line grooves machined according to the API
requirements and hardened on their surfaces for everlasting; quenced-and-tempered forged alloy
steel; central pin holed to provide the individual lubrication of each bearing.

• MC-type hook blocks whose max. hook load values range between 100 t (110 sht)
and 500 t (550 sht).

• MCA-type hook blocks, whose max. hook load is 500 t (550 sht) and which are directly coupled,
thus permitting both-way motion parallel and perpendicular to the locking bolt
and perpendicular to any face along the vertical axis.

• MCm-type hook blocks featuring three values of the max. hook load, as follows:
250 t (275 sht), 450 t (500 sht), 320 t (350 sht) and having features due to the Mt new type
of blocks and CPt hooks.

Max. Line
Sheaves
Type Working Load Diameter
mton(tf) tons No. mm mm in
MCA
6.38.1500.MCA-500 500 550 6 1,500 38 1. 1/2
6.35.1400.MCA-500 500 550 6 1,500 35 1. 3/8
MC
6.35.1400.MC-400 400 440 6 1,400 35 1. 3/8
5.35.1400.MC-400 400 440 5 1,400 35 1. 3/8
5.32.1250.MC-300 300 330 5 1,250 32 1. 1/4
5.32.1100.MC-200 200 220 5 1,100 32 1. 1/4
4.28.1100.MC-200 200 220 4 1,100 28 1. 1/8
4.28.750.MC-136 136 150 4 750 28 1. 1/8
4.28.750.MC-125 125 138 4 750 28 1. 1/8
4.25.750.MC-125 125 138 4 750 25 1
4.25.560.MC-100 100 110 4 560 25 1
MCm
6.35.1400.MCm-500 500 550 6 1,400 35 1. 3/8
5.32.1250.MCm-350 320 350 5 1,250 32 1. 1/4
5.32.1120.MCm-250 225 250 5 1,120 35 1. 3/8

HOOK BLOCKS
CROWN BLOCKS
The crown blocks are available for 10 max. values of the hook load and designed
for being used either with MC-, MCA-, MCm-type hook blocks or with travelling
blocks having the same working-load of the hook.The crown block shaft
is made of quenced-and-tempered forged alloy-steel and permits the individual
lubrication of each bearing.

Max. Working load Sheaves Line diameter

Type
mton (tf) tons No. mm mm in
9.48.1830.GF-910 910 1,000 9 1,830 48 1. 7/8
7.38.1500.GF-650 590 650 7 1,500 38 1. 1/2 CROWN BLOCKS
7.38.1500.GF-500 500 550 7 1,500 38 1. 1/2
6 1,400
(6+1).35.1400.GF-500 500 550 35 1. 3/8
1 1,650
7.35.1400.GF-500 500 550 7 1,400 35 1. 3/8
7.35.1400.GF-400 400 440 7 1,400 35 1. 3/8
6.35.1400.GF-400 400 440 6 1,400 35 1. 3/8
6.35.1250.GF-300 300 330 6 1,250 35 1. 3/8
(5+1).28.1016.GF-200 200 220 6 (5+1) 1,016 28 1. 1/8
5.28.1100.GF-200 200 220 5 1,100 28 1. 1/8
6.28.1100.GF-200 200 220 6 1,100 28 1. 1/8
6.32.1100.GF-200 200 220 6 1,100 32 1. 1/4
6.32.1250.GF-200 300 330 6 1,250 32 1. 1/4
(4+2).28.750.GF-136 136 150 6 (4+2) 750 28 1. 1/8
(4+2).28.750.GF-125 125 138 6 (4+2) 750 28 1. 1/8 CROWN BLOCKS
(4+2).25.560.GF-100 100 110 6 (4+2) 560 25 1

SWIVELS
UPETROM manufactures a series of swivels whose static load values range
between 32 t (35 sht) and 680 t (750 sht). The above specified swivels are highly
advantageous from several points of view, such as:

• long life provided by the quality of the materials and the heat-treatment cycles;
• a main axial taper-roller bearing that takes over heavy loads and has reduced
dimensions;
• the wash pipe sealing system can be laterally taken out and provides quick
replacement of the wash pipe and seals when they are heated;
• the swivels are delivered with subs connecting with the kellies.

Max. Static Load API Bearing Load Max. Pressure Threaded Connection Sizes
Type
mton(tf) tons mton(tf) tons bar psi Goose-Neck Sub
CH-750 680 750 431 475 350 5,000 4 LP 8. 5/8 REG-LH
CH-650 650 715 431 475 320 4,640 4 LP 6. 5/8 REG-LH
350 5,000
CH-500 500 550 365 400 500 7,500 4 LP 6. 5/8 REG-LH

300 4,300
CH-400 400 440 210 230 500 7,500 4 LP 6. 5/8 REG-LH

300 4,300
CH-320 320 350 153 167 500 7,500 3 LP 6. 5/8 REG-LH

CH-200 200 220 125 138 210 3,000 4 LP 6. 5/8 REG-LH

CH-136 136 150 108 119 210 3,000 4 LP 6. 5/8 REG-LH
CH-125 125 138 88.8 94 210 3,000 3 LP 6. 5/8 REG-LH
CH-80 80 88 77 85 210 3,000 3 LP 6. 5/8 REG-LH
CH-50 50 55 28 31 210 3,000 TE 70-2. /2 LP
1 3. 1/2 REG-LH
CH-32 32 35 25 27 140 2,000 3 LP 4. 1/2 REG-LH SWIVELS