Temperature Compensated

Water Cut Monitor

Energy Systems Model WCM 7300
Bulletin SSIS003

The Model WCM 7300 is designed to provide the highest

possible sensitivity, resolution, and accuracy for water con-
tent determination in crude oil, other hydrocarbons, or other
low dielectric liquids from a max of 25% to levels below 1000
parts per million (ppm). In oil and natural gas (condensate)
production, water cut and S&W measurements are signifi-
cantly improved with the WCM 7300 technology. Enhanced
digital signal processing and full product temperature compen-
sation are two of the technological advancements utilized by
this device. Probe sizes from 2” through 12” are available. 4-
20 mA and 0-5 volt outputs are available for remote readout.
Water cut, process temperature or probe electrical value can
be selected for viewing without removing condulet cover
by use of a supplied magnet to operate an internal reed
switch.

Product Temperature Compensation

The base dielectric constant (Dk) of oils can change with

changes in temperature. This can cause traditional moni- WCM 7300 Water Cut Monitor
tors to change without a variance in water content. For
example; for a 10°F change, a typical curde oil may show Measurement/Monitor Specifications
a reading shift of as much as 0.1%, which normally would
be considered as water. The WCM 7300 measures prod- Power Supply
uct temperature and calculates a corrected cut reading,
providing a true water or S&W cut at any temperature up to 20-30 Vdc +/-10% @ nominal, 100 mA max.
160°F. S&W Full Scale Range
0-25%
Field adjustable to 0-5%, 0-10%, etc.
Features Accuracy
NACE Adaptable - Can be modified for use in sour Is defined as the variance observed between the 7300
service. reading and the water grindout of the oil.
Normal variances are:
Applications
+/-.05 from 0 to 5% water
LACT (Lease Automatic Custody Transfer) Units +/-.1 from 5 to 10% water
Detect and provide relay contact closure that can be used +/-.15 from 10% to 15% water
to reroute oil that has excess S&W. +/-.2 to .25 from 15 to 25% water
Pipeline Loading Displays
Monitor transfer of petroleum/condensate products from One line 16 character, alphanumeric LCD showing by se-
loading facilities. lection:
Dehydration Equipment Water Cut
Determine and enhance equipment efficiencies, by moni- Process Temperature
toring the product and indicating water content. Probe Electrical Value
Fuel Oil Monitoring Red/Green LED showing good oil, bad oil, or by passing,
Determine contamination of fuel oil by condensation, or condition.
other external factors, before entry to engine. Pressure Ratings
Storage and Treating Facilities As per Flange selection, 1440 psig max. (Others by special
Monitoring and early detection of undesirable conditions order)
as well as interface detection during de-watering of storage NPT - 1440 psig max.
tanks.
Victualic grooved - 350 psig

FMC INVALCO ! Fluid Control ! Stephenville, Texas 76401 ! Telephone: 254/968-2181 ! FAX 254/968-5709 ! Toll Free: 800/468-2526
WCM 7300 Dimensions
Inches (mm)

Note: Dimensions - Inches to the nearest tenth (millimeters to the nearest whole mm), each independently dimensioned from respective
engineering drawings.

WCM 7300 Probe/Monitor Assemblies Ordering Information

WCM WATER CUT MONITOR, DIGITAL, TEMPERATURE COMPENSATING, Ranges from 0-20% water
7300 PROBE MATERIAL: Carbon Steel
l
l CODE PROBE BODY SIZE
l 2 2 INCH I.D. x 17" FACE TO FACE
l 3 3 INCH I.D. x 32" FACE TO FACE
l 4 4 INCH I.D. x 32" FACE TO FACE
l 6 6 INCH I.D. x 32" FACE TO FACE
l 8 8 INCH I.D. x 32" FACE TO FACE
l l CODE END CONNECTIONS
l l 00 SCREWED ENDS (to 3" only)
l l 00 GROOVED ENDS/Victaulic (to 4" only)
l l 00 150 LB ANSI RAISED FACE
l l 30 300 LB ANSI RAISED FACE
l l 60 600 LB ANSI RAISED FACE (SCH 80) (FOR 8" AND 10")
l l 90 900 LB ANSI RAISED FACE and RING JOINT (SCH 160) (FOR 10")
l l 05 150 LB ANSI RTJ
l l 35 300 LB ANSI RTJ
l l 65 600 LB ANSI RTJ (SCH 80) (FOR 8" AND 10")
l l 95 900 LB ANSI RTJ (SCH 80)
l l 115 1500 LB ANSI RTJ (SCH 160)
l l l CODE MATERIAL AND TEMPERATURE OPTIONS
l l l B STANDARD MATERIALS, A53B CARBON STEEL, -20-160F
l l l H STANDARD MATERIALS/HIGH TEMP, -20 - 375F1
l l l S 316 STAINLESS STEEL MATERIALS -20-160F
l l l T 316 STAINLESS STEEL/HIGH TEMP, -20 - 375F 1
l l l l CODE CONNECTION STYLE
l l l l S SCREWED CONNECTIONS, MNPT
l l l l G VICTAULIC CONNECTIONS (GROOVED)
l l l l F FLANGED CONNECTIONS
l l l l l CODE OPEN
l l l l l P Epoxy
l l l l l l
Example: l l l l l
WCM7300 - 4 60 - B F P = WCM7300 - 460 - BFP
Choose one code selection from each option group to build model number and correct pricing.
Notes:
1 - Consult factory for temperature compensation

www.fmcinvalco.com
The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the
specifications are currently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been changed and
are no longer in effect.
FMC INVALCO Fluid Control Stephenville, TX 76401, Phone: 254/968-2181, FAX: 254/968-5709, Toll Free: 800/468-2526
2 • SSIT042
Printed in U.S.A. © 6/05 FMC INVALCO All rights reserved. Issue/Rev. 0.1 (2/04)