SCHEME OF EXAMINATION

&

DETAILED SYLLABUS

For

BACHELOR OF TECHNOLOGY
(Tool Engineering)

GURU GOBIND SINGH

INDRAPRASTHA UNIVERSITY
KASHMERE GATE, DELHI
www.ipu.ac.in

1
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH.) DEGREE COURSE (Common to all branches)

FIRST SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETMA 101 Applied Mathematics – I 3 1 4
ETPH 103 Applied Physics – I 2 1 3
ETCH 105 Engineering Chemistry – I 2 1 3
ETME 107 Manufacturing Process 2 0 2
ETCS 109 Introduction to Computers and 2 1 3
Auto CAD
ETEL 111 Communication Skills – I 2 1 3
ETEL 113* Impact of Science & Technology 1 0 1
on Society
PRACTICAL/VIVA VOCE
ETPH 151 Applied Physics Lab. – I - 2 1
ETCH 153 Engineering Chemistry Lab. – I - 2 1
ETCS 155 Introduction to Auto CAD Office - 3 2
Automation and Web Design
ETME 157 Workshop Practice - 3 2
ETME 159 Engineering Graphics Lab. - 2 1
TOTAL 14 17 26

ETEL-113* is NUES

2
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH.) DEGREE COURSE (Common to all branches)

SECOND SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETMA 102 Applied Mathematics – II 3 1 4
ETPH 104 Applied Physics – II 2 1 3
ETCH 106 Environmental Studies 2 1 3
ETCS 108 Introduction to Programming 2 1 3
ETME 110 Engineering Mechanics 2 1 3
ETEC 112 Electrical Science 2 1 3
ETEL 114 Communication Skills – II 2 1 3
PRACTICAL/VIVA VOCE
ETPH 152 Applied Physics Lab. – II - 2 1
ETCH 154 Environmental Studies Lab. - 2 1
ETCS 156 C Programming Lab. - 2 1
ETME 158 Engineering Mechanics Lab. - 3 2
ETEC 160 Electrical Science Lab. - 2 1
TOTAL 15 18 28

3
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH. in Tool Engineering) DEGREE COURSE

THIRD SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETTE 201 Numerical Analysis & 3 1 4
Programming
ETME 203 Electronics 3 1 4
ETTE 205 Engineering Thermodynamics & 3 1 4
Heat Transfer
ETME 207 Mechanics of Solids 3 1 4
ETTE 209 Machine Design & Drawing 4 0 4
ETME 211 Mechanics of Fluids 3 1 4
PRACTICAL/VIVA VOCE
ETME 251 Electronics Lab 0 2 1
ETME 253 Mechanics of Solids/ Fluid 0 2 1
Mech.Lab
ETME 255 Machine Design & Drawing Lab 0 2 1
ETTE 257 Numerical Analysis & 0 2 1
Programming Lab
TOTAL 19 13 28

4
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH. in Tool Engineering) DEGREE COURSE

FOURTH SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETME 202 Kinematics & Dynamics of 3 1 4
Machines
ETTE 204 Finite Elements Methods 3 1 4
ETTE 206 Machine Tools 3 1 4
ETTE 208 Basics of Automation 3 1 4
ETTE 210 Industrial Management and Quality 3 1 4
Control
ETTE 212 Engineering Metals & Metallurgy 3 1 4
Practical/Viva Voce
ETME 252 KOM Lab. /DOM Lab. 0 2 1
ETTE 254 FEM Lab 0 2 1
ETTE 256 Machine Tools Lab 0 2 1
ETTE 258 Automation Lab 0 2 1
Total 18 14 28

NOTE : Immediately after the End Term Examinations of Fourth Semester the students
shall proceed for Industrial/Practical Training of 6 weeks. However, Viva-Voce will be
conducted in the Fifth Semester.

Each student shall undergo a scheduled Industrial/Practical Training at various reputed

Industrial/Commercial Tool Room, Research & Development Organization, Automobile
Manufacturing Sectors, Mass Production Industries, Public Sector Undertakings,
Railways, Airways, Shipways etc.

5
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH. in Tool Engineering) DEGREE COURSE

FIFTH SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETTE 301 Production Planning & Control 3 0 3
ETTE 303 Metrology & Quality Assurance 3 0 3
ETTE 305 Jigs ,Fixture & Gauge Design 3 1 4
ETTE 307 CNC Machining & Programming 3 1 4
ETTE 309 Plastic Technology 3 1 4
PRACTICAL/VIVA VOCE
ETTE 351 Metrology & Quality Assurance Lab 0 2 1
ETTE 353 Jigs, Fixture & Gauge Design Lab 0 2 1
ETTE 355 CNC Machining and Programming 0 2 1
Lab
ETTE 357 @ Minor Project(with a thrust on 0 4 2
Design Innovation & Manufacturing)
ETTE 359 # ^Industrial/Practical Training - - 2
Total 15 13 25

# Non University Examination System.

^ Industrial/Practical training conducted after Fourth Semester. However, Viva-Voce for

evaluation of Industrial/Practical Training will be conducted during Fifth semester End
Exams by the duly constituted panel comprising of :

1. Institute Representative(Director/Principal or his nominee).

2. Industry Representative (External Examiner appointed by the Vice-
Chancellor/Controller of Examination).

6
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH. in Tool Engineering) DEGREE COURSE

SIXTH SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETTE 302 Press Tool Design – I 3 1 4
ETTE 304 Mould Design – I 3 1 4
ETTE 306 Rapid Prototyping & Reverse 3 1 4
Engineering
ETTE 308 Metal Cutting & Tool Design 3 1 4
ELECTIVES (Select any one)
ETTE 310 Concurrent Engineering 3 1 4
ETTE 312 Value Engineering 3 1 4
ETTE 314 Ergonomics 3 1 4
ETTE 316 Precision Engineering 3 1 4
ETTE 318 Statistical Quality Control 3 1 4
PRACTICAL/VIVA VOCE
ETTE 352 Press Tool Design - I Lab 0 4 2
ETTE 354 Mould Design – I Lab 0 4 2
ETTE 356 Rapid Prototyping & Reverse Engg 0 4 2
Lab
ETTE 358 Metal Cutting & Tool Design Lab 0 4 2
Total 15 21 28

NOTE: Immediately after the End Term Examinations of Sixth Semester the students
shall proceed for Industrial/Practical Training of 6 weeks. However, Viva-Voce will be
conducted in the Seventh Semester.

Each student shall undergo a scheduled Industrial/Practical Training at various reputed

Industrial/Commercial Tool Room, Research & Development Organization, Automobile
Manufacturing Sectors, Mass Production Industries, Public Sector Undertakings,
Railways, Airways, Shipways etc.

7
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH. in Tool Engineering) DEGREE COURSE

SEVENTH SEMESTER EXAMINATION

Code No Paper L T/P Credits

ETTE 401 CAD & Product Design 3 1 4
ETME 403 Mechatronics 3 1 4
ETTE 405 Press Tool Design – II 3 1 4
ETTE 407 Mould Design – II 3 1 4
PRACTICAL/VIVA VOCE
ETTE 451 CAD & Product Design Lab 0 2 1
ETME 453 Mechatronics Lab 0 2 1
ETTE 455 Press Tool Design – II Lab 0 4 2
ETTE 457 Mould Design – II Lab 0 4 2
ETTE 459 # Project Part - I 0 8 4
(Project Planning & Appraisal)
ETTE 461 ^ Industrial/Practical Training - - 2
TOTAL 12 24 28

# The major project will be completed in two parts i.e. Project Part – I(7 th Sem) and
Project Part – II(8th Sem). The student will submit a synopsis at the beginning of the
semester for approval from the departmental committee in a specified format. The
student will have to present the progress of the work through seminars and progress
reports (Project Planning and Appraisal on Tool Design & Manufacturing).

^ Industrial/Practical training conducted after Sixth Semester. However, Viva-Voce for

evaluation of Industrial/Practical Training will be conducted during Seventh semester
End Exams by the duly constituted panel comprising of :

3. Institute Representative(Director/Principal or his nominee).

4. Industry Representative (External Examiner appointed by the Vice-
Chancellor/Controller of Examination).

8
Effective from academic session 2008 - 09
 BACHELOR OF TECHNOLOGY
(B.TECH. in Tool Engineering) DEGREE COURSE

EIGHTH SEMESTER EXAMINATION

Code No Paper L T/P Credits

THEORY PAPER
ETTE 402 Die Casting & Die Design 3 1 4
ETTE 404 Modern Manufacturing Methods 3 1 4
Elective (Select any one)
ETTE 406 Material Management 3 1 4
ETTE 408 Safety Engineering 3 1 4
ETTE 410 Flexible Manufacturing 3 1 4
Systems(FMS) &Computer
Integrated Manufacturing Systems
(CIMS)
ETTE 412 Advance Mechanical Engineering 3 1 4
Design
ETME 416 Financial Management 3 1 4
ETME 418 Reliability & Maintenance 3 1 4
Management
PRACTICAL / VIVA VOCE
ETTE 452 Project Part - II - 16 8
(Project Work Tool Design &
Manufacturing)
TOTAL 9 24 20

NOTE:
1. The total number of the credits of the B.Tech. (TE) Programme = 211
2. Each student shall be required to appear for examinations in all courses. However,
for the award of the degree a student shall be required to earn the minimum of 200
credits.

9
Effective from academic session 2008 - 09
Paper Code: ETMA-101 L TC
Paper: APPLIED MATHEMATICS – I 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
COMPLEX NUMBERS AND INFINITE SERIES: De Moivre’s theorem and roots of
complex numbers. Euler’s theorem, Logarithmic Functions, Circular, Hyperbolic
functions and their Inverses. Convergence and Divergence of Infinite series,
Comparison test d’Alembert’s ratio test. Higher ratio test, Cauchy’s root test. Alternating
series, Lebnitz test, Absolute and conditioinal convergence. [No. of Hrs. 10]

UNIT II
CALCULUS OF ONE VARIABLE: Successive differentiation. Leibnitz theorem (without
proof) McLaurin’s and Taylor’s expansion of functions, errors and approximation.
Asymptotes of Cartesian curves. Curveture of curves in Cartesian, parametric and polar
coordinates, Tracing of curves in Cartesian, parametric and polar coordinates (like
conics, astroid, hypocycloid, Folium of Descartes, Cycloid, Circle, Cardiode, Lemniscate
of Bernoulli, equiangular spiral). Reduction Formulae for evaluating Finding area under
the curves, Length of the curves, volume and surface of solids of revolution.
[No. of Hrs. 15]
UNIT III
LINEAR ALGEBRA – MATERICES: Rank of matrix, Linear transformations, Hermitian
and skeew – Hermitian forms, Inverse of matrix by elementary operations. Consistency
of linear simultaneous equations, Diagonalisation of a matrix, Eigen values and eigen
vectors. Caley – Hamilton theorem (without proof). [No. of Hrs. 09]

UNIT IV
ORDINARY DIFFERENTIAL EQUATIONS: First order differential equations – exact and
reducible to exact form. Linear differential euations of higher order with constant
coefficients. Solution of simultaneous differential equations. Variation of parameters,
Solution of homogeneous differential equations – Canchy and Legendre forms.
[No. of Hrs. 10]
TEXT BOOKS :
1. Kresyzig, E., “Advanced Engineering Mathematics”, John Wiley and Sons.
(Latest edition) , 2007
2. Jain, R. K. and Iyengar, S. R. K., “Advanced Engineering Mathematics”, Narosa, (2 nd
Ed.), 2003.

REFERENCE BOOKS :
1. Mitin, V. V.; Polis, M. P. and Romanov, D. A., “Modern Advanced Mathematics for
Engineers”, John Wiley and Sons, 2001.
2. Wylie, R., “Advanced Engineering Mathematics”, McGraw-Hill, 1995.
3. Dr. A. B. Mathur, V. P. Jaggi , “Advanced Engineering Mathematics”, Khanna
Publications, 2008.

10
Effective from academic session 2008 - 09
Paper Code: ETPH – 103 L TC
Paper: APPLIED PHYSICS – I 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Interference of Light: Interference due to division of wavefront and division of amplitude,
Young’s double slit expt., Interference, Principle of Superposition, Theory of Biprism,
Interference from parallel thin films, wedge shaped films, Newton rings, Michelson
interferometer. Diffraction: Fresnel Diffraction, Diffraction at a straight edge, Fraunhoffer
diffraction due to N slits, Diffraction grating, absent spectra, dispersive power of Grating,
resolving power of prism and grating. [No. of Hrs. 8]

UNIT II
Polarization: Introduction, production of plane polarized light by different methods,
Brewster and Malus Laws. Double refraction, Quarter & half wave plate, Nicol prism,
specific rotation, Laurent’s half shade polarimeter. Optical Instruments : Ramdson &
Huygen Eye pieces, Electron microscope. [No. of Hrs. 8]

UNIT III
Laser: Introduction, temporal and spatial coherence, principle of Laser, stimulated and
spontaneous emission, Einstein’s Coefficients, He-Ne Laser, Ruby Laser, Application of
Lasers. Fibre Optics: Introduction, numerical aperture, step index and graded index
fibres, attenuation & dispersion mechanism in optical fibers (Qualitative only),
application of optical fibres, optical communication (block diagram only) [No. of Hrs. 8]

UNIT IV
Mechanics: Central and non-central forces, Inverse square force, SHM, Damped,
undamped and forced Oscillations. Special theory of Relativity: Frame of reference,
Michelson-Morley experiment, basic postulates of special relativity, Lorentz
transformations (space – time coordinates & velocity only), mass energy relation.
[No. of Hrs. 8]

TEXT BOOKS :
1. A. Ghatak, “Optics”, TMH, 2007.
2. N. Subrahmanyam and Brij Lal, “Optics” , S Chand and Co. , 2008

REFERENCE BOOKS :
1. Jenkins and White, “Fundamentals of Optics”, Mcgraw Hill, 2001.
2. C. Kittle, “Mechanics”, Berkeley Physics Course, Vol.- I., TMH, 2008.
3. A. Beiser, “Concepts of Modern Physics”, TMH 2008.

11
Effective from academic session 2008 - 09
Paper Code: ETCH – 105 L TC
Paper: ENGINEERING CHEMISTRY – I 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.
However, student may be asked to attempt only 1 question from each unit. Each question should be of 12.5 marks.

UNIT I
WATER TECHNOLOGY : Introduction and specifications of water, Hardness and its
determination (EDTA method only), Alkalinity, Boiler feed water, boiler problems –
scale, sludge, priming & foaming: causes & prevention, Boiler problems – caustic
embrittlement & corrosion : causes & prevention, Removal of silica & dissolved gases;
carbonate & phosphate conditioning, Water softening  processes : Lime – soda process,
Ion exchange method, colloidal conditioning & calgon treatment , Water for domestic
use. [No. of Hrs. 8]

UNIT II
FUELS : Classification, calorific value of fuel, (gross and net), Determination of calorific
value of fuels, bomb calorimeter,  Boy's Gas calorimeter, Solid fuels - Proximate and
ultimate analysis, High & Low temperature carbonisation, manufacture of coke (Otto-
Hoffmann oven), Liquid Fuels – Petroleum-Chemical composition, fractional distillation,
Cracking - Thermal & catalytic cracking, Octane & Cetane No. and its significance,
Power Alcohol, Analysis of flue gases (Orsat's apparatus).     [No. of Hrs. 8]

UNIT III
GASEOUS STATE : Gas Laws and Kinetic Theory of gases, Distribution of molecular
velocities, Mean free path, Real gases-non ideal behaviour, Causes of deviation from
ideal behaviour, Vander Waal’s equation, liquefaction of gases. [No. of Hrs. 5]

UNIT IV
THERMOCHEMISTRY : Hess’s Law, Heat of Reaction, Heat of dilution, Heat of
Hydration, Heat of neutralization and Heat of Combustion, Effect of temperature on heat
of reaction at constant pressure (Kirchoff’s equation), Flame Temperature.
[No. of Hrs. 2]

UNIT V
THE PHASE RULE : Definition of various terms, Gibb’s Phase rule, Application of
phase rule to one component system- The water system and sulphur system, Two
component system- Lead-Silver, FeCl3- water, Na2SO4 – water.
[No. of Hrs.
3]

UNIT VI

CATALYSIS : Characteristics, types and theories of catalysis, concept of promoters,

inhibitors and poisons, Homogenous catalysis (mechanisms of acid-base and Enzyme),
catalysis by metal salts, Heterogenous catalysis (mechanism of surface reactions).
[No. of Hrs.
4]
12
Effective from academic session 2008 - 09
TEXT BOOK :
1. Sunita Rattan, “Engineering Chemistry”, S K Kataria & Sons, 2008.
2. By J.C. Kuriacose & J. Rajaram, “Chemistry in Engineering & Technology (Vol I & II)”
Tata Mcgraw Hill, 1999.

REFERENCE BOOK:
1. Puri B.R., Sharma L.R. and Pathania, “M.S.Principles of Physical Chemistry”, Shoban
Lal Nagin chand & Co. ,2000.
2. S.S. Dara,.”Text book of Engg. Chemistry”, S. Chand & Co., 2003.
3. H.D. Gesser “Applied Chemistry “, Springer, 2001.

13
Effective from academic session 2008 - 09
Paper Code: ETME 107 L TC
Paper: MANUFACTURING PROCESS 2 0 2
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Casting Processes: Principles of metal casting: Pattern materials, types and allowance;
Study of moulding, sand moulding, tools, moulding materials, classification of moulds,
core, elements of gating system, casting defects, description and operation of cupola:
special casting processes e.g. die-casting, permanent mould casting, centrifugal
casting, investment casting. [No. of Hrs. 6]

UNIT II
Smithy and Forging: Basic operation e.g. upsetting, fullering, flattening, drawing,
swaging: tools and appliances: drop forging, press forging. Bench Work and Fitting
Fitting, sawing, chipping, thread cutting (die), tapping; Study of hand tools, Marking and
marking tools. [No. of Hrs. 6]

UNIT III
Metal joining: Welding principles, classification of welding techniques; Oxyacetylene
Gas welding, equipment and field of application, Arc-welding, metal arc, Carbon arc,
submerged arc and atomic hydrogen welding, Electric resistance welding: spot, seam,
butt, and percussion welding; Flux: composition, properties and function; Electrodes,
Types of joints and edge preparation, Brazing and soldering. [No. of Hrs. 6]

UNIT IV
Sheet Metal Work: Common processes, tools and equipments; metals used for sheets,
standard specification for sheets, spinning, bending, embossing and coining.
[No. of Hrs. 5]

TEXT BOOKS :
1. Raghuvanshi, “Manufacturing Process”, Dhanpat Rai Publication, 2008.
2. P.N.Rao, “Manufacturing Technology”, TMH publications, 2008.

REFERENCE BOOKS :
1. Hazra-Chowdhary, “ Workshop Technology”, Media Promoters, 2007.
2. R.K.Jain, “Production Technology” , Khanna Publication, 2008.
3. Chapman, “Workshop Technology” CBS, 1995.

14
Effective from academic session 2008 - 09
Paper Code: ETCS 109 L TC
Paper: INTRODUCTION TO COMPUTERS AND AUTO CAD 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction to Computer: Overview of Computer organization and historical perspective
computer applications in various fields of science and management. Data
representation: Number systems, character representation codes, Binary, hex, octal
codes and their inter conversions. Binary arithmetic, Floating-point arithmetic, signed
and unsigned numbers. [No. of Hrs. 8]

UNIT II
Introduction to OS and Office Automation Concept of computing, Introduction to
Operating Systems such as DOS, windows 2000/Xp, UNIX, Client Server Technology,
etc. (only brief user level description). Introduction to World Processing, Spread Sheet &
Presentation software e.g. MS-Word, MSExcel, MS-Power Point. [No. of Hrs. 8]

UNIT III
Introduction to Auto CAD Coordinate System, 2D drafting: lines, circles, arc, polygon,
etc., Editing, 3D, Solid modeling, Rendering, Use of Auto CAD for engineering drawing
practices. [No. of Hrs. 8]

UNIT IV
Web Technologies : Introduction to World Wide Web, Search engines, e-mail, news,
gopher, Audio & Video Conferencing, Internet Protocols: FTP, telnet, TCP/IP, SMTP,
HTTP, Languages used for WEB Technology: HTML, practical examples using DHTML
and Static HTML
[No. of Hrs. 8]

TEXT BOOKS :
1. Rajaraman, “Fundamentals of Computers”, Prentice Hall of India, 3rd Edition, 2007.
2. Mark Middlebrook, “Autocad 2004 for Dummies”, Wiley Dreamtech, 2000.
3. Vikas Gupta, “Comdex Computer Course Kit”, Dreamtech Press, 2004.

REFERENCE BOOKS :
1. Alexis Leon & Mathews Leon, “Fundamentals of Computer Science &
Communication Engineering”, Leon Techworld, 1998.
2. Omura, “Mastering Autocad 2000 for Mechanical Eng ineers” BPB Publications, 2nd
Edition, 1998.
3. A.S. Tanenbaum, “ Computer Networks”, Pearson Education India Ltd., 3rd Edition,
2002.

15
Effective from academic session 2008 - 09
Paper Code: ETEL-111 L TC
Paper: COMMUNICATION SKILLS – I 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks. 2. Apart from question no. 1, rest of the paper shall consist of four
units as per the syllabus. Every unit should have two questions. However, student may be asked to attempt only 1
question from each unit. Each question should be of 12.5 marks.

UNIT I
Remedial Grammar: Errors of Accidence and syntax with reference to Parts of Speech;
Agreement of Subject and Verb; Tense and Concord; Conditional Clauses; Use of
connectives in Complex and Compound sentences; Question tags and short responses.
[No. of Hrs: 06]

UNIT II
Vocabulary and Usage: Word Formations (by adding suffixes and prefixes); Technical
Word Formation; Synonyms, Antonyms, Homophones, and Homonyms; One Word
Substitution; Misappropriations; Indianisms; Redundant Words; Phrasal Verb Idioms.
[No. of Hrs: 06]

UNIT III
Technical Writing: (A) Scientific Attitude and Impersonal Style; Plain Statements,
Definitions; Description and Explanations (of objects, instruments, Processes, Scientific
Principles, etc.) Summarizing and abstracting; Expressing ideas within a restricted word
limit; Paragraph Writing (Paragraph division, introduction and the conclusion, Variety in
sentences and paragraphs) Interpretation and use of charts, graphs and tables in
technical writing. Punctuation
(B) Reading at various speeds (slow, fast, very fast); reading different kinds of texts for
different purpose (e.g. for relaxation, for information, for discussion at a later stage,
etc.); reading between the lines. Comprehension of Unseen Passages
[No. of Hrs: 10]

UNIT IV
Text: The following prose pieces from Best Science Writing : Reading and Insights
edited by Robert Gannon prescribed text (Hyderabad: University Press (India) Limited,
1991).
1. Chapter 2: “After 63 years, Why Are They Still Testing Einstein?” by C.P.
Gilmore
2. Chapter 5: “Star Wars : The Leaky Shield” By Carl Sagan
3. Chapter 10: “Chaos : The Ultimate Asymmetry” by Arthur Fisher
4. Chapter 11: “Bill Moss, Tentmaker” by Robert Gannon
5. Chapter 12: “Totality - A Report” by Michael Rogers
[No. of Hrs: 10]

TEXT BOOKS :
1. Maison, Margaret M. “Examine Your English”, Hyderabad: Orient Longman, 1980
2. Sharma, R.S. “Technical Writing”. Delhi: Radha Publication, 1999
3. Sudarsanam, R. “Understanding Technical English”. Delhi: Sterling Publishers Pvt.
Ltd.,1992
16
Effective from academic session 2008 - 09
4. Gannon, Robert, Edt. “Best Science Writing: Readings and Insights”. Hyderabad:
University Press (India) Limited, 1991.

Paper Code: ETEL-113 L TC

Paper: Impact of Science & Technology on Society* 1 0 1
*Non University Examination Scheme (NUES)
There will not be any external examination of the university. The performance of the
candidates should continuously be evaluated by an internal committee. The committee
may conduct viva voce at the end for the award of the marks.

17
Effective from academic session 2008 - 09
Paper Code: ETPH-151 PC
Paper: APPLIED PHYSICS LAB – I 2 1

List of Experiments

(1) To plot a graph between the distance of the knife-edge from the center of the gravity
and the time period of bar pendulum. From the graph, find
(a) The acceleration due to gravity
(b) The radius of gyration and the moment of inertia of the bar about an axis.
(2) To determine the moment of inertia of a flywheel about its own axis of rotation.
(3) To determine the value of acceleration due to gravity using koter’s pendulum.
(4) To determine the frequency of A.C. mains using sonometer and an electromagnet.
(5) To determine the frequency of electrically maintained turning fork by Melde’s
method.
(6) To determine the dispersive power of prism using spectrometer and mercury source.
(7) To determine the wavelength of sodium light by Newton’s Ring.
(8) To determine the wavelength of sodium light using diffraction grating.
(9) To determine the refractive index of a prism using spectrometer.
(10) To determine the specific rotation of cane sugar solution with the help of
polarimeter.
(11) To find the wavelength of He-Ne Laser using transmission diffraction grating.
(12) To determine the numeral aperture (NA) of a Optical Fibre.
(13) Compute simulation (simple application of Monte Carlo) e.g. Brownian motion,
charging & discharging of capacitor.

Note: Any 8-10 experiments out of the list may be chosen. Proper error – analysis must
be carried out with all the experiments.

18
Effective from academic session 2008 - 09
 Paper Code: ETCH – 153 PC
Paper: ENGINEERING CHEMISTRY LAB – I 2 1

List of Experiments

1. Determine the percentage composition of sodium hydroxide in the given mixture of sodium
hydroxide and sodium chloride.

2. Determine the amount of Oxalic acid and Sulphuric acid in one litre of solution, given standard
sodium hydroxide and Potassium Permanganate.

3. Determine the amount of copper in the copper ore solution, provided hypo solution.

4. Argentometric titration one each by Vohlard’s method and by Mohr’s method.

5. Complexometric titrations.

6. Determine the heat of neutralization of strong acid with strong base.

7. Determine the surface tension of a liquid using drop weight method.

8. Determine viscosity of a given liquid (density to be determined).

9. Determine the reaction rate constant for the Ist order reaction.

10.Determine the cell constant of a conductivity cell and titration of strong acid/strong base
conductometrically.

TEXT BOOKS :
1. Sunita Rattan, “Experiment in Applied Chemistry”, S K Kataria & Sons, 2007.

REFERENCE BOOKS:
1. Vogel’s “Textbook of Quantitative Chemical Analysis” (Latest ed.), Revised by G.H.
Jeffery, J. Bassett, J. Mendham & R.C. Denney, Pearson, 2008
2. O.P. Vermani & A.K. Narula, “Applied Chemistry: Theory and Practice”, New Age
International (P) Ltd, 2007

19
Effective from academic session 2008 - 09
Paper Code: ETCS 155 PC
Paper: Introduction to Auto CAD, Office Automation and Web Design 3 2

List of Experiments

1. Use Microsoft-Word to perform the following:

a) Send out invitation letter to several people using mail merge facility.
b) Create tabular data in word and insert graph to represent data.
c) Create a Macro and use it in an application.

2. Use Microsoft-Excel to perform the following:

a) Create a Macro and use it in an application
b) Enter the name and marks of 10 students and perform various mathematical
functions on it.
c) Enter first quarter performance of five companies and create a pie chart
showing there shareholders in the market.

3. Use Microsoft Power-Point to perform the following

a) Create a slide show on any subject of your choice using minimum five slides.
b) Create slideshow in operating sound.
c) Create an animation using group, ungroup, order, textbox image insert etc.

4. Use HTML to design a Home page for IGIT using all the features of HTML like
buttons, frames, marquee check boxes etc..

5. Use AutoCAD to do the following:

a) Use of Drawing & Editing Properties: Modify Object Properties and a know
how of layers, colors and prototype drawing.
b) Draw line (Poly line, multi line, linear line), polygon, ellipse, circle, arc,
rectangle and use cross hatching, regions, boundary, spline, donut, fillet and
extent commands.
c) Dimensioning commands, styles, control scale factors, drawing set-up, grip
editing objects snaps, utility commands.
d) Projection of points, lines and solids,
e) Section of Solids
f) Development and Intersection of Surface
g) Isomeric Projections

Create a WEB page containing hyperlinks to the pages having information about
Science and Technology.

20
Effective from academic session 2008 - 09
Paper Code: ETME-157 PC
Paper: WORKSHOP PRACTICE 3 2

UNIT I
Materials: Spectrography method for finding composition of materials.
Wood Working Shop: Making of various joints, Pattern making.

UNIT II
Foundary Shop: Bench moulding with single piece pattern and two piece pattern.
Floor moulding – Making of bend pipe mould etc.
Machine moulding – Making of mould using Match-plate pattern.
Core making- Making and baking of dry sand cores for placing in horizontal, vertical and
hanging positions in the mould cavity.

Fitting Shop: Learning use of fitting hand tools, marking tools, marking gauge.
Exercises: Jobs made out of MS Flats, making saw – cut filling V-cut taper at the
corners, circular cut, fitting square in square, triangle in square.

UNIT III
Welding Shop: Electric arc welding, Edge preparations, Exercises making of various
joints. Bead formation in horizontal, vertical and overhead positions.
Gas Welding: Oxy-Acetylene welding and cutting of ferrous metals.
Soldering: Dip soldering.
Brazing: With Oxy-Acetylene gas.

UNIT IV
Sheet Metal Shop: Learning use of sheet-metal tools, Exercises: Making jobs out of GI
sheet metal. Cylindrical, Conical and Prismatic shapes.
Project Shop: Extrusion of soft metals, Plastic coating of copper wires, Plastic moulding.

21
Effective from academic session 2008 - 09
Paper Code: ETME-159 PC
Paper: ENGINEERING GRAPHICS LAB 2 1

UNIT I
General: Importance, Significance and scope of engineering drawing, Lettering,
Dimensioning, Scales, Sense of proportioning, Different types of projections,
Orthographic Projection, B.I.S. Specifications.

Projections of Point and Lines: Introduction of planes of projection, Reference and

auxiliary planes, projections of points and Lines in different quadrants, traces,
inclinations, and true lengths of the lines, projections on Auxiliary planes, shortest
distance, intersecting and nonintersecting lines.

UNIT II
Planes other than the Reference Planes: Introduction of other planes (perpendicular
and oblique), their traces, inclinations etc., Projections of points and lines lying in the
planes, conversion of oblique plane into auxiliary Plane and solution of related
problems.

Projections of Plane Figures: Different cases of plane figures (of different shapes)
making different angles with one or both reference planes and lines lying in the plane
figures making different given angles (with one of both reference planes). Obtaining true
shape of the plane figure by projection.

UNIT III
Projection of Solids: Simple cases when solid is placed in different positions, Axis
faces and lines lying in the faces of the solid making given angles.
CADD

UNIT IV
Isometric Projection.
Nomography : Basic Concepts and use.

TEXT BOOKS :
1. N.D.Bhatt, “Engineering drawing”, Charotar Publications, 1995.

REFERENCE BOOKS :
1. S.C.Sharma & Navin Kumar, “Engineering Graphics with Auto Cad”, Galgotia
Publications, 2002.
2. Venugopalan, “Engineering Drawing”, New Age International Publication, 1992.
3. P.S.Gill, “Engineering Drawing”, S K Kataria and Sons, 2008.

22
Effective from academic session 2008 - 09
Paper Code: ETMA-102 L TC
Paper: APPLIED MATHEMATICS - II 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
CALCULUS OF SEVERAL VARIABLES: Partial differentiation, ordinary derivatives of
first and second order in terms of partial derivaties, Euler’s theorem on homogeneous
functions, change of variables, Taylor’s theorem of two variables and its application to
approximate errors. Maxima and Minima of two variables, Langranges method of
undermined multipliers and Jacobians. [No. of Hrs. 12]

UNIT II
FUNCTIONS OF COMPLEX VARIABLES: Derivatives of complex functions, Analytic
functions, Cauchy-Riemann equations, Harmonic Conjugates, Conformal mapping,
Standard mappings – linear, square, inverse and bilinear. Complex line integral,
Cauchy’s integral theorem, Cauchy’s integral formula, Zeros and Singularities / Taylor
series, Laurents series, Calculation of residues. Residue theorem, Evaluation and real
integrals. [No. of Hrs. 12]

UNIT III
VECTOR CALCULUS: Scalar and Vector point functions, Gradient, Divergence, Curl
with geometrical physical interpretations, Directional: derivatives, Properties.
Line integrals and application to work done, Green’s Lemma, Surface integrals and
Volume integrals, Stoke’s theorem and Gauss divergence theorem (both without proof).
[No. of Hrs. 10]

UNIT IV
LAPLACE TRANSFORMATION: Existence condition, Laplace transform of standard
functions, Properties, Inverse Laplace transform of functions using partial fractions,
Convolution and coinvolution theorem. Solving linear differential equations using
Laplace transform. Unit step function, Impulse function and Periodic function and their
transforms. [No. of Hrs. 10]

TEXT BOOKS :
1. E. Kresyzig, “Advanced Engineering Mathematics”, John Wiley and Sons. 8 th edition.
2. R. K. Jain and S. R. K. Iyengar, “Advanced Engineering Mathematics”, Narosa, 2003
(2nd Ed.).
3. Dr. A. B. Mathur, V. P. Jaggi, “Advanced Engineering Mathematics”, Khanna
Publishers. 1985.

REFERENCE BOOKS :
1. V. V. Mitin, M. P. Polis and D. A. Romanov, “Modern Advanced Mathematics for
Engineers”, John Wiley and Sons, 2001.
2. R. Wylie, “Advanced Engineering Mathematics”, McGraw-Hill, 1995.
23
Effective from academic session 2008 - 09
Paper Code: ETPH-104 L TC
Paper: APPLIED PHYSICS – II 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each un it. Each question should be
of 12.5 marks.

UNIT I
Electromagnetic Theory (EMT) :Motion of Charged Particles in crossed electric &
magnetic fields, Velocity Selector & Magnetic focussing, Gauss law, continuity equation,
inconsistency in Ampere’s Law, Maxwell’s equations (differential and integral forms),
poynting vector, Poynting Theorem (Statement only), propagation of plane
electromagnetic waves in conducting and non-conducting medium.
[No. of Hrs. 8]
UNIT II
Quantum Mechanics & Statistical Physics: De-Broglie Hypothesis, Davisson Germer
experiment, wave function and its properties, expectation value, Wave Packet,
Uncertainity principle. Schrodinger Equation for free Particle, Time Dependent
Schrodinger Equation, Particle in a box (1-D), Single step Barrier, Tunneling
effect. Qualitative Features of Maxwell Bollzman, Bose-Einstein and Fermi-Dirac
statistics distribution, functions & their comparison (no derivation) [No. of Hrs. 8]

UNIT III
Solid State Physics: Formation of energy bands in metals, semiconductors and
insulators; intrinsic and extrinsic semiconductors, Fermi energy levels for doped,
undoped semiconductors and pn junction; Tunnel diode, Zener diode.
Superconductivity: Meissner Effect, Type I and Type II Superconductors, BCS theory
(Qualitative only), London’s equation, properties of superconductors & applications.
[No. of Hrs.
8]

UNIT IV
X-Rays: production and properties, Crystalline and Anorphous solids (Brief) Bragg’s
Law, Applications. Ultrasonics: Introduction, Production of Ultrasonics (Magentostriction
and piezoelectric methods), engineering applications. [No. of Hrs. 8]

TEXT BOOKS :
1. A. BEISER, “Concept of Modern Physics”, Mcgraw Hill, 1983.
2. J.B. Rajam, “Atomic Physics”, S Chand and Co. Ltd, 2007
3. Greiner, “Quantum Physics”, Springer Verlag, 1989
4. Griffth, “Introduction to Electrodynamics”, Dorling Kindersley, 3 rd Edittion, 2008

REFERENCE BOOKS :
1. Jordan & Balmain, “Electromagnetic waves and Radiating Systems”, Prentice Hall,
1974.
2. Kittel, “Solid State Physics” Wiley, 2007.

24
Effective from academic session 2008 - 09
3. Schiff, “Quantum Mechanics”, Mcgraw Hill, 1968.

Paper Code: ETCH – 106 L TC

Paper: ENVIRONMENTAL STUDIES 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
MULTIDISCIPLINARY NATURE OF ENVIRONMENTAL STUDIES
Definition, scope and importance, need for public awareness, introduction to concept of
green technology. [No. of Hrs. 2]

UNIT II
ENVIRONMENTAL CONSERVATION AND MANAGEMENT
Forest resources: Use and over-exploitation, deforestation, Timber extraction, mining,
dams and their effects on forest and tribal people.
Water resources: Use and over-utilization of surface and ground water, floods, drought,
conflicts over water, dams-benefits and problems.
Mineral resources: Use and exploitation, environmental effects of extracting and using
mineral resources.
Food resources: World food problems, changes caused by agriculture and over-grazing,
effects of modern agriculture, fertilizer-pesticide problems, water logging, salinity.
Energy resources: Growing energy needs, renewable and non renewable energy
sources, use of alternate energy sources-green fuel.
Land resources: Land as a resource, land degradation, man induced landslides, soil
erosion and desertification.
Resource Management-Sustainable development. [No. of Hrs. 7]

UNIT III
ENVIRONMENTAL POLLUTION & CONTROL
Air Pollution - Types of pollutants, source, effects, sink & control of primary pollutants–
CO, NOX, HC, SOx and particulates, effect of pollutants on man & environment:
photochemical smog, acid rain and global warming, CO2 Sequestration.
Water Pollution - Classification of Pollutants, their sources, waste water treatment
(domestic and industrial).
Soil Pollution – Composition of soil, classification and effects of solid pollutants and
their control.
Solid Waste Pollution – Classification, waste treatment and disposal methods;
compositing, sanitary land filling, thermal processes, recycling and reuse methods.
Hazardous wastes - Classification, radioactive, biomedical & chemical, treatment and
disposal- Physical, chemical and biological processes.
Marine Pollution – Causes, effects and control of marine pollution, coastal zone
management. [No. of Hrs. 7]

UNIT IV
CHEMICAL TOXICOLOGY
25
Effective from academic session 2008 - 09
Toxic chemicals in the environment, Impact of toxic chemicals on enzymes, biochemical
effects of arsenic, cadmium, lead, chromium, mercury, biochemical effects of pesticides.
[No. of Hrs. 4]
UNIT V
ECO-FRIENDLY POLYMERS
Polymer synthesis, Environmental degradation of polymers, photodegradable polymers,
hydrolysis and hydro-biodegradable polymers, biopolymers and bioplastics, thermal
degradation of plastics during recycling. [No. of Hrs. 3]

UNIT VI
ENVIRONMENTAL BIOTECHNOLOGY
Bioaccumulation, biodegradation, bioremediation, bioleaching, Biomethanation,
[No. of Hrs. 2]
UNIT VII
GREEN TECHNOLOGY
Introduction, Basic principles of green technology, concept of Atom economy, Tools of
Green technology, zero waste technology. [No. of Hrs. 3]

UNIT VIII
ENVIRONMENTAL MANAGEMENT SYSTEMS
Objectives, Components, Environmental Impact Assessment, Some important
Environmental laws, Green bench, Carbon Credits, Environmental Management System
standards-ISO 14000 series. [No. of Hrs. 3]

TEXT BOOKS:
1. Rani Gadi, Sunita Rattan, Sushmita Mohapatra, “Environmental Studies”, S K Kataria
& Sons, 2009.

REFERENCE BOOKS:
1. Roger Perman et. al., “Natural Resources & Environmental Economics, 2nd Ed.,
Longman, USA, 2000
2. Stern, A.C “Air Pollution, Vol. 1-VIII”, Academic Press, (1980).
3. James M., Lynch & Alan Wiseman, “Environmental Bio-monitoring : The
Biotechnology Ecotoxicology Interface”, Cambridge University Press, 1998.
4. John Glasson, Riki Therivel and Andrew Chadwick, “Introduction to Environmental
Impact Assessment”, 2nd Ed., UCL Press, Philadelphia, USA, 1994.
5. Richard K. Morgan, “Environmental Impact Assessment: A methodological
perspective”, Kluwar Academic Publications, Boston, 1998.
6. Gabriel Bitton, “Wastewater Microbiology”, 2nd Ed., Wiley-Liss, New York, 1999.
7. S.S. Dara, “Environmental Chemistry & Pollution Control”, S. Chand & Co. (Latest
ed.),
8. Balaram Pani, “Environmental Chemistry”, I.K. Publishers, 2007,
9. A.K. De, “Environmental Chemistry”, New Age Int. Publ. (Latest ed.).
10. S.K. Dhamija, “Environmental Studies”, S.K. Kataria Publ. . (Latest ed.).
11. V. Subramanian, “A text book in Environmental Science”, Narosa Publ. 2007,.

26
Effective from academic session 2008 - 09
Paper Code: ETCS 108 LTC
Paper: Introduction to Programming 213
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction to Programming:
Concept of algorithms, Flow Charts, Data Flow diagrams etc., Introduction to the Editing
tools such as vi or MS-VC editors, Concepts of the finite storage, bits bytes, kilo, mega
and gigabytes. Concepts of character representation, Number Systems & Binary
Arithmetic. [No. of Hrs. 8]

UNIT II
Programming using C
The emphasis should be more on programming techniques rather than the language
itself. The C Programming language is being chosen mainly because of the availability
of the compilers, books and other reference materials.
Example of some simple C program. Concept of variables, program statements and
function calls from the library (Printf for example) C data types, int, char, float etc., C
expressions, arithmetic operation, relational and logic operations, C assignment
statements, extension of assignment of the operations. C primitive input output using
getchar and putchar, exposure to the scanf and printf functions, C Statements,
conditional executing using if, else. Optionally switch and break statements may be
mentioned. [No. of Hrs. 8]

UNIT III
Iterations and Subprograms
Concept of loops, example of loops in C using for, while and do-while. Optionally
continue may be mentioned. One dimensional arrays and example of iterative programs
using arrays, 2-d arrays Use in matrix computations.
Concept of Sub-programming, functions Example of functions. Argument passing
mainly for the simple variables. [No. of Hrs. 8]

UNIT 4
Pointers and Strings
Pointers, relationship between arrays and pointers Argument passing using pointers
Array of pointers. Passing arrays as arguments. Strings and C string library.
Structure and Unions. Defining C structures, passing strings as arguments
programming examples. [No. of Hrs. 8]

TEXT BOOKS:
1. Yashwant Kanetkar, “Let us C”, BPB Publications, 2nd Edition, 2001.
2. Herbert Schildt, “C:The complete reference”, Osbourne Mcgraw Hill, 4th Edition,
2002.
27
Effective from academic session 2008 - 09
REFERENCE BOOK:
1. Raja Raman, “Computer Programming in C”, Prentice Hall of India, 1995.
2. Kernighan & Ritchie, “C Programming Language”, The (Ansi C Version), PHI, 2nd
Edition.

28
Effective from academic session 2008 - 09
Paper Code: ETME 110 L TC
Paper: ENGINEERING MECHANICS 2 1 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Force system: Free body diagram, Equilibrium equations and applications.
Friction: Static and Kinetic friction, laws of dry friction, co-efficient of friction, angle of
friction, angle of repose, cone of friction, friction lock, friction of flat pivot and collared
thrust bearings, Belt drive- derivation of equation.
T1/T2 =eμθ and its application
[No. of Hrs. 8]
UNIT II
Structure: Plane truss, perfect and imperfect truss, assumption in the truss analysis,
analysis of perfect plane trusses by the method of joints, method of section.
Distributed Force: Determination of center of gravity, center of mass and centroid by
direct integration and by the method of composite bodies, mass moment of inertia and
area moment of inertia by direct integration and composite bodies method, radius of
gyration, parallel axis theorem, Pappus theorems, polar moment of inertia.
[No. of Hrs. 8]
UNIT III
Kinematics of Particles: Rectilinear motion, plane curvilinear motion-rectangular
coordinates, normal and tangential component.
Kinetics of Particles: Equation of motion, rectilinear motion and curvilinear motion,
work energy equation, conservation of energy, impulse and momentum conservation of
momentum, impact of bodies, co-efficient of restitution, loss of energy during impact.
[No. of Hrs. 8]
UNIT IV
Kinematics of Rigid Bodies: Concept of rigid body, type of rigid body motion, absolute
motion, introduction to relative velocity, relative acceleration (Corioli’s component
excluded) and instantaneous center of velocity, Velocity and acceleration polygons for
four bar mechanism and single slider mechanism.
Kinetics of Rigid Bodies: Equation of motion, translatory motion and fixed axis
rotation, application of work energy principles to rigid bodies conservation of energy.
Shear force and bending Moment Diagram.
[No. of Hrs. 8]
TEXT BOOKS:
1. A.K.Tayal, “Engg Mechanics “, Umesh Publications, 2008.
2. Sadhu Singh, “Engg Mechanics”, Khanna Publishers, 2003.

REFERENCE BOOKS:
1. Irving H. Shames, “Engg Mechanics” PHI publications, 1983.
2. U.C.Jindal, “Engg Mechanics”, Galgotia Publications, 2000.

29
Effective from academic session 2008 - 09
3. Beer & Johnston, “Vector Mechanics for Engineers Vol I & Vol II Dynamics”, TMH,
1997 .
4. Subramanyam, “Engg Mechanics “, Vikash Publishing House Pvt Ltd, 1999.

Paper Code: ETEC-112 LTC

Paper: ELECTRICAL SCIENCE 213
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Circuit Analysis
Ohm’s Law, KCL, KVL Mesh and Nodal Analysis, Circuit parameters, energy storage
aspects, Superposition, Thevenin’s, Norton’s, Reciprocity, Maximum Power Transfer
Theorem, Millman’s Theorem, Star-Delta Transformation. Application of theorem to the
Analysis of dc circuits. [No. of Hrs. 8]

UNIT II
A.C.Circuits
R-L, R-C, R-L-C circuits (series and parallel), Time Constant, Phasor representation,
Response of R-L, R-C and R-L-C circuit to soinusoidal input Resonance-series and
parallel R-L-C Circuits, Q-factor, Bandwidth. [No. of Hrs. 7]

UNIT III
Measuring Instruments
Principles, Construction and application of moving coil, moving iron, dynamometer type,
induction type instruments, extension of range of ammeter, voltmeter (shunt and
multiplier), Two-wattmeter method, for the measurement of power, Cathol-ray
Oscilloscope and Applications. [No. of Hrs. 7]

UNIT IV
Transformers
Construction and Working principles and phaser diagrams of Single-phase Transformer,
Emf equation, Equivalent circuit, Regulation and efficiency, and Auto transformer.
Rotating Machines
Construction and working principles of dc motor and generator and its characteristics
Applications of DC machines
Construction and working principles of 3-j-Induction motor, Torque-speed
characteristics, and Industrial applications.
[No. of Hrs. 10]
TEXT BOOKS:
1. P.C. Sen “Principles of Electric Machines and Power Electronics”, Wiley Eastern
2003.
2. Vincent DEL TORO “Electrical Engineering Fundamental’s Prentice Hall India”, Ed
2002.

30
Effective from academic session 2008 - 09
Paper Code: ETEL-114 L TC
Paper: COMMUNICATION SKILLS – II 2 13
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Basic Concepts in Communication: Communication as sharing; context of
communication; the speaker/writer and the listener/reader; medium of communication;
barriers to communication; accuracy, brevity, clarity and appropriateness in
communication. [No. of Hrs: 05]

UNIT II
Writing Skills: Types of writings (Expository, Descriptive, Analytic, Argumentative,
Narrative etc) and their main features. Resumes and CV’s and Cover letters. Memos and Notices.
Basics of Formal Reports. [No. of Hrs: 08]

UNIT III
Verbal, Non-Verbal and Listening Skills: Elementary Phonetics (Speech Mechanism,
The Description of Speech Sounds, The Phoneme, the syllable; Prosodic Features, Word Accent,
Features of Connected Speech); Paralanguage and Body language; and
Classroom Presentations, Hearing and Listening; Essentials of Good Listening:
Achieving ability to comprehend material delivered at relatively fast speed.
[No. of Hrs: 08]
UNIT IV
Group Discussion: Use of persuasive strategies including some rhetorical devices for
emphasizing (for instance; being polite and firm; handling questions and taking in
criticism of self; turn-taking strategies and effective intervention; use of body language).
[No. of Hrs: 09]

TEXT BOOKS:
1. Bansal, R.K. and J. B. Harrison. “Spoken English For India: A Manual of Speech
and Phonetics” , Hyderabad: Orient Longman, 1983.
2. Lewis, Hedwig, “ Body Language: A Guide For Professionals”, New Delhi:
Response Books (A division of Sage Publication), 2000.
3. Sides, Charles H. , “How to Write & Present Technical Information”, Cambridge:
CUP, 1999.
4. Forsyth, Sandy & Lesley Hutchison., “Practical Composition”, Edinburgh : Oliver
& Boyd, 1981

31
Effective from academic session 2008 - 09
Paper Code: ETPH 152 PC
Paper: APPLIED PHYSICS LAB – II 2 1

List of Experiments

1. To determine the value of e/m of electron by J.J. Thomson method.

2. To determine unknown resistance of a wire by Carey Foster’s Bridge.

3. To determine the internal resistance of Leclanche cell using potentiometer.

4. To study the charging and discharging of a capacitor and to find out the time
constant.

5. To find the thermal conductivity of a poor conductor by Lee’s disk method.

6. To study the thermo emf using thermocouple and resistance using Pt. Resistance
thermometer.

7. To determine the velocity of ultrasound waves using an ultrasonic spectrometer in a

given liquid (Kerosene Oil)

8. To measure the frequency of a sine-wave voltage obtain from signal generator and to
obtain lissajous pattern on the CRO screen by feeding two sine wave voltage from two
signal generator.

9. To determine the temp. coefficient of resistance of platinum by Callender & Griffith’s

Bridge.

10. To study Hall effect.

11. To determine plank’s constant.

Note: Atleast 8 experiments must be carried out.

Proper error – analysis must be carried out with all the experiments.

32
Effective from academic session 2008 - 09
Paper Code: ETCH 154 PC
Paper: ENVIRONMENTAL STUDIES LAB. 2 1

List of Experiments

1. Determination of alkalinity in the water sample.

2. Determination of dissolved oxygen (DO) in the water sample.
3. Determination of Biological oxygen demand (BOD) in the water sample.
4. Determination of Chemical oxygen demand (COD) in the water sample.
5. Determination of pH, conductivity and turbidity in some drinking water samples
and preparation of report.
6. Determination of Residual Chlorine in the water sample.
7. Determination of pH and conductivity of soil/sludge samples.
8. Determination of moisture content of soil sample.
9. Determination of Total dissolved solids in water/effluent sample.
10. Preparation of Urea-formaldehyde polymer.
11. To determine (a) λ max of the solution of KMnO 4 (b) Verify Beer’s law and find
out the concentration of unknown solution by spectrophotometer.
12. To determine the concentration of iron in water sample by spectrophotometer.
13. To determine the concentration of particulate matter in the ambient air using High
Volume Sampler.

Note: Any eight-ten experiments out of the list may be chosen.

TEXT BOOKS:
1. Ranu Gadi, Sunita Rattan, Sushmita Mohapatra, “Environmental Studies”, S K
Kataria & Sons, 2009.

REFERENCE BOOKS:

1. Standard Methods for the Examination of Water and Wastewater, American Public
Health Association (APHA), American Water Works Association (AWWA) & Water
Environment Federation (WEF), 2005. 
2. Experiments in Applied Chemistry, Sunita Rattan, Publ.: S.K. Kataria & Sons, Delhi,
2005.
3. Applied Chemistry, Theory and Practice, O.P. Virmani and A.K. Narula, New Age Int.
Publ., Delhi, 1999.
4. Laboratory Manual on Engg. Chemistry, S.K. Bhasin and Sudha Rani, Dhanpat Rai
Publ. Comp., New Delhi, 2003.

33
Effective from academic session 2008 - 09
Paper Code: ETCS 156 PC
Paper: C PROGRAMMING LAB. 2 1

List of Experiments
1. Write a program to produce ASCII equivalent of given number

2. Write a program to find divisor or factorial of a given number.

3. Write a program to evaluate the following algebraic expressions after reading

necessary values from the user
 (ax+b)/(ax-b)
 2.5 log x-cos 30+|x^2-y^2|+sqrt (2xy)
 (x^5+10x^4+8x^3+4x+2

4. Write a program to find sum of a geometric series

5. Write a program to cipher a string

6. Write a program to check whether a given string follows English capitalization rules

7. Write a program to find sum of the following series

1+ ½ + 1/3 +________+1/20

8. Write a program to search whether a given substring exist in an input string or not
and then delete this string from input string.

9. Write a recursive program for tower of Hanoi problem

10. The fibonacci sequence of numbers is 1,1,2,3,5,8……. Based on the recurrence

relation F(n)=F(n-1)+F(n-2)for n>2
Write a recursive program to print the first m Fibonacci number

11. Write a menu driven program for matrices to do the following operation depending
on whether the operation requires one or two matrices

a) Addition of two matrices

b) Subtraction of two matrices
c) Finding upper and lower triangular matrices
d) Trace of a matrix
e) Transpose of a matrix
f) Check of matrix symmetry
g) Product of two matrices.

12. Write a program that takes two operands and one operator from the user perform
the operation and then print the answer

34
Effective from academic session 2008 - 09
13. Write a program to print the following outputs:
1
22
333
4444
55555

14. Write functions to add, subtract, multiply and divide two complex numbers (x+iy) and
(a+ib) Also write the main program.

15. Write a menu driven program for searching an sorting with following options:-
a) Searching (1) Linear searching (2) Binary searching
b) Sorting (1) Insersection sort (2) Selection sorting

16. Write a program to copy one file to other, use command line arguments.

17. Write a program to mask some bit of a number (using bit operations)

18. An array of record contains information of managers and workers of a company.

Print all the data of managers and workers in separate files.

35
Effective from academic session 2008 - 09
Paper Code: ETME 158 PC
Paper: ENGINEERING MECHANICS LAB 3 2

List of Experiments

1. To verify the law of Force Polygon

2. To verify the law of Moments using Parallel Force apparatus. (simply supported type)

3. To determine the co-efficient of friction between wood and various surface (like
Leather, Wood, Aluminum) on an inclined plane.

4. To find the forces in the members of Jib Crane.

5. To determine the mechanical advantage, Velocity ratio and efficiency of a screw jack.

6. To determine the mechanical advantage, Velocity ratio and Mechanical efficiency of

the Wheel and Axle

7. To determine the MA, VR, η of Worm Wheel ( 2-start)

8. Verification of force transmitted by members of given truss.

9. To verify the law of moments using Bell crank lever

10. To find CG and moment of Inertia of an irregular body using Computation method.

36
Effective from academic session 2008 - 09
Paper Code: ETEC 160 PC
Paper: ELECTRICAL SCIENCE LAB 2 1

List of Experiments

1. Verification of Thevenin’s theorem

2. Verification of Superposition theorem

3. Phasor Diagram and Power factor of LCR circuit.

4. Measurement of Power and Power factor in single phase Load using three
ammeters/voltmeters.

5. Calibration of Energy Meter/Wattmeter/Voltmeter/Ammeter

6. Two wattmeter method of measuring power in three phase circuit (resistive load only)

7. Load test on Single Phase Transformer, Regulation and Efficiency of Transformer

8. Short Circuit/Open Circuit tests on Single Phase transformer

9. Measure the armature and field resistance of a D.C. Machine

10. Connection and starting of a Three Phase Induction Motor using direct on line or
Star Delta Starter.

11. Starting and Speed Control of a D.C. shunt motor

12. Resonance

37
Effective from academic session 2008 - 09
Paper Code: ETTE - 201 L TC
Paper: NUMERICAL ANALYSIS & PROGRAMMING 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per t he syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Numerical Techniques: The solution of linear and non-linear equations: Direct Iteration
method, Regula-Falsi method, Newton – Raphson method. Solution of system of
simultaneous equations by Gauss elimination, Gauss-Jacobi and Gauss-Seidal
methods.Finite differences: Forward, backward and Central differences.
[No. of Hrs.: 11]

UNIT II:
Interpolation and Numerical Calculus: Newton’s interpolation for equi-spaced values.
Divided differences and interpolation formula in terms of divided differences. Stirling’s
central difference interpolation formula, Lagrange’s interpolation formula for unequi-
spaced values. Numerical Differentiation. Numerical Integration: Newton-Cote’s
quadrature formula, Trapezoidal rule, Simpson’s one-third rule and Simpson’s three-
eighth rule. [No. of Hrs.: 11]

UNIT III:
Numerical solution of ordinary differential equations: Picard’s method, Euler’s method,
modified Euler’s method, Runge-Kutta method of fourth order, Milne’s predictor-
corrector method. [No. of Hrs.: 11]

UNIT IV:
Computer Programming: Writing programmes in C++ for solving numerical problems.
For example, Programme for solving algebraic and transcendental equations by
Newton-Rapson Method, solving simultaneous equations by Gauss-Seidal method.
Programme for Interpolation by Lagrange’s method. Programme for estimating the
value an integral by Simpson’s rule. Programme for solving differential equation by
Runge-Kutta method, etc. [No. of Hrs.: 11]

TEXT BOOKS :
1. V.P. Mishra; “TEXT BOOKS : of Engineering Mathematics”, Galgotia Publications,
Delhi, 2006.
2. B.S. Grewal, “Higher Engineering Mathematics”, Khanna Publications, Delhi, 40 th
Edition, 2004.
3. V.P. Jaggi and A.B. Mathur, “Advanced Engineer Mathematics”, Khanna
Publications, Delhi, 1985.

REFERENCE BOOKS :
1. S.S. Sastry, “Introductory Methods of Numerical Analysis”, Prentice Hall of India Pvt.
38
Effective from academic session 2008 - 09
Ltd., New Delhi , 1990.
2. M.K. Jain, S.R.K Iyengar, R.K. Jain, “Numerical Methods for Scientific and
Engineering Computation”, New Age International Publishers, New Delhi, 2003.

Paper Code: ETME - 203 L TC

Paper: ELECTRONICS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Semiconductor Diodes: Introduction to Junction Diode, Rectifiers (Half wave & Full
wave), Filters, Voltage Regulation and Voltage Multiplier. Types of Diodes (Zener,
Photo, LED),Liquid Crystal Display (LCD), Introduction to Silicon Controlled Rectifier
(SCR), DIAC, TRIAC. Bipolar Junction Transistor: BJT Characteristics, CB, CE & CC
Configuration, Load Line (DC & AC), Leakage Current, Saturation, Active & Cut off
mode of operation of Transistor, Biasing methods. [No. of Hrs.: 11]

UNIT II
Small Signal Amplifier: CB, CE, CC, Amplifier, Hybrid Model Analysis of Common
Emitter Amplifier, RC Coupled Amplifier, Mid-Band Model, gain and Impedance,
Comparison of Different Configurations, Darlington Amplifier. Large Signal Amplifier:
Introduction to Class A, Class B, Class C Amplifier, Class B Push Pull Amplifier.
Oscillator: Concept of Negative & Positive feedback, Introduction to LC Oscillators
[No. of Hrs.: 11].

UNIT III
Field Effect Transistor: Introduction, Classification, FET Characteristics, Depletion &
Enhancement MOSFET.Operational Amplifier: Op-Amp Model, Concept of Ideal Op-
Amp, Concept of Virtual Ground, Inverting & Non-Inverting Amplifier, Differential
Amplifier, Adder & Sub tractor, V – I & I – V Converter, Integrator, Differentiator,
Comparators. [No. of Hrs.: 11]

UNIT IV
Digital Circuits: Binary operation, Boolean Algebra, Different Types of Codes (BCD,
Gray, Excess-3, ASCII) DeMorgan’s Law, Karnaugh Map, Different Types of Gates, Half
Adder, Full Adder, Encoders, Decoders, Multiplexers, DeMultiplexers, Flipflops,
Counters, Shift Registers, Introduction to RAMs and ROMs. [No. of Hrs.: 11]

TEXT BOOKS :
1. Millman & Halkias, “Electronic Devices & Circuits”, Tata Mcgraw Hill, 1967.
2. R.L. Boylestos & L. Nashesky, “Electronic Devices & Circuits”, Pearson Education,
2006.
3. S. Salivahenan, N. Suresh Kr. & A. Vallavaraj, “Electronic Devices & Circuit”, Tata
McGraw Hill, 1998.

REFERENCE BOOKS :
1. R.P. Jain, “Modern Digital Electronics”, Tata Mcgraw Hill, 1984.
39
Effective from academic session 2008 - 09
2. Malvino & Leach, “Digital Principle And Applications”, Tata Mcgraw Hill, 1985.

Paper Code: ETTE - 205 L TC

Paper: ENGINEERING THERMODYNAMICS & HEAT TRANSFER 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks

UNIT I
Basic thermodynamics: Work and heat transfer, First law of thermodynamics applied to
closed and open systems, Second law of thermodynamics, Carnot’s propositions,
Clausius inequality, entropy principle. Air standard cycles: Carnot, Otto, diesel and dual
cycles.
Principle of working of 2 stroke and 4 stroke internal combustion engines, valve timing
diagrams and performance testing. [No. of Hrs.: 08]

UNIT II
Properties of steam: T-v, P-v, T-s, P-T, h-s diagrams, Mollier diagram. Steam
generators: classification, construction and functioning, mountings and accessories.
Refrigeration Cycles: Basics of air, vapour compression and vapour absorption
refrigeration cycles.
Vapour power cycles: Carnot and Rankine cycles, Reheat and regenerative cycles,
thermal efficiency and work ratios. Gas turbine cycles with heat exchanger and
regeneration. [No. of Hrs.: 08]

UNIT III
One-dimensional steady-state conduction through homogeneous and composite plane
walls, cylinders and spheres, critical thickness of insulation; heat transfer from fins of
uniform cross section.
Concept of hydrodynamic and thermal boundary layers, momentum and energy
equation for boundary layers on a flat plate application of dimensional analysis to free
and force convection; important dimensionless number. [No. of Hrs.: 08]

UNIT IV
Thermal radiation; Kirchoff’s law; Planck’s distribution law, Wien’s displacement law;
Stefan-Boltzmann’s relation, Configuration factors; radiant interchange between black
and grey surfaces; radiation shielding solar radiation. [No. of Hrs.: 08]

UNIT V
Combined heat transfer analysis; overall heat transfer co-efficient; types of heat
exchangers; LMTD methods of heat exchanger design; simple heat exchanger
calculations. [No. of Hrs.: 08]

TEXT BOOKS :

40
Effective from academic session 2008 - 09
1. V.P. Vasandani and D.S. Kumar, “Treatise on Heat Engineering”, Metropolitan
Books Co. Pvt Ltd, 2000.
2. John R.Howell & Richrd O Buckius, “Fundamentals of Engg. Thermodynamics”,
McGraw Hill International, 1992.
3. P.K. Nag, “Engineering Thermodynamics”, Tata McGraw Hill, 1981.

REFERENCE BOOKS :
1. Sonntag/Van Wylene, “Fundamentals of Thermodynamics”, Wiley, 2007.
2. Rahul Gupta, “Engineering Thermodynamics”, Asian Books P. Ltd, 2003.

41
Effective from academic session 2008 - 09
Paper Code: ETME 207 L TC
Paper: MECHANICS OF SOLIDS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Simple Stresses & strains: Tensile, Compressive, shear and volumetric stresses and
Strains, stress strain diagram, complementary shear stress, lateral strain and Poisson’s
ratio. Compound bars and Temperature stresses: Stresses in compound bars carrying
axial loads and subjected to temperature stresses. Complex stresses and strains:
Principle stress and strain due to combination of stresses, Mohr’s circle theories of
Failures. [No. of Hrs.: 11]

UNIT II
Simple bending: Shear force and bending moment diagrams of cantilevers, beams
under concentrated, uniformly varying loads with and without overhangs.
Stresses in beams and cantilevers under bending, beam of uniform strength, flitched
beams, bending due to eccentric loads.Slope and defection of cantilevers and beams
under concentrated and uniformly distributed loads. [No. of Hrs.: 11]

UNIT III
Columns: Combined direct and bending stresses in columns, Euler’s and Rankine
Gordon equations. Torsion: Stresses and strains in pure torsion of solid circular shafts
and hollow circular shafts. Power transmitted by shafts; combined bending and torsion.
[No. of Hrs.:
11]

UNIT IV
Springs: Close-coiled, open coiled springs under torque and moment.
Cylinders: Thin and thick cylinders, Lame’s Theorem, compound cylinders, spherical
vessels.
[No. of Hrs.: 11]

TEXT BOOKS :
1. Jindal U.C., “Strength of Materials”, Galgotia Publication, New Delhi, 1998.
2. Ryder G.H., “Strength of Materials”, Macmillan, Delhi, 2003.
3. R.K. Bansal, “Strength of Materials”, Laxmi Publication, New Delhi, 2001.

REFERENCE BOOKS :
1. Sadhu Singh, “Strength of Materials”, Khanna Publishers, New Delhi, 2000.
2. Timoshenko S.P., “Elements of Strength of Materials”, East-West affiliated, New
Delhi, 2000.
42
Effective from academic session 2008 - 09
3. Hibbler R.C., “Mechanics of Materials”, Prentice Hall, New Delhi, 1994.
4. Popov Eger P., “Engg. Mechanics of solids”, Prentice Hall, New Delhi, 1998.
5. Fenner, Roger.T, “Mechanics of Solids”, U.K. B.C. Publication, New Delhi, 1990.
6. Sri Nath L.S. et.al., “Strength of Materials”, McMillan, New Delhi,2001

Paper Code: ETTE 209 L TC

Paper: MACHINE DESIGN & DRAWING 4 0 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Principles of mechanical design, systematic design process, aesthetic
and ergonomic considerations in design, use of standards in design. Manufacturing
consideration in design, casting, machining, forging Dynamic and fluctuating stresses,
fatigue failure and endurance limit, stress concentration, causes and remedies in design
Factor of safety, Tolerances and types of fits, Selection of materials [No. of Hrs.: 11]

UNIT II
Conventions : Theory of Dimensioning as per as I. S. code, Sectional views and
sectioning convention. Engineering drawing convention regarding surface finish and
tolerances, conventional representation of machine parts such as bearings, springs,
gears, symbols for welding, riveting, Bill of materials. [No. of Hrs.: 08]

UNIT III
Assembly Drawing : Machine tool parts: Tool Post of Lathe, Tool head of shaping
machine, Tail stock, Machine vice. [No. of Hrs.: 08]

UNIT IV
Engine Cross Head. Boiler Mountings, lever safety valve Blow off cock and Non return
valve and Steam Stop valve. I. C. Engine Parts - Two stroke and Four stroke Engine,
Piston, connecting rod. Bearings - Sliding and Ball bearings, Thrust ball bearing.
[No. of Hrs.: 11]

TEXT BOOKS :
1. J.E.Shigley, “Mechanical engineering design”, McGraw Hill, 1977.
2. James G.Bralla, “Handbook of product design for manufacturing”, McGraw Hill, 1986

REFERENECE BOOKS :
1. Bhandari, “Design of machine elements “, TMH, 1994.
2. V.I.Doughtie, A.Vallence, “Design of machine members”, McGraw Hill, 1964.
3. Hartman, Maleev, “Mechanical design of machines”, CBS Delhi, 1986.
4. Sadhu Singh, “Machine Design”, Khanna Publication, 2004.
5. Pandya & Shah, “Machine Design”, Charotar Publishing House, 1994.
6. Mahadevan & Balaveera Reddy, “Design Data Hand Book for Mechanical
Engineers”, CBS Publication, 1986.
43
Effective from academic session 2008 - 09
Paper Code: ETME:211 L TC
Paper : MECHANICS OF FLUIDS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.
UNIT I
Fluid Properties and Fluid Statics: Newtonian and Non-Newtonian Fluids; Kinematic and
dynamic Viscosity; Incompressible and compressible fluids, compressibility.
Forces on plane surfaces, forces on curved surfaces, buoyant forces, stability of floating
bodies, metacentre and metacentric height. Kinematics of Fluid Motion: Steady and
unsteady flow; uniform and non-uniform flow; Laminar and turbulent flow; streamline,
path line and streak line; continuity equation, irrotational and rotational flow, velocity
potential and stream function, vortex flow, vortex lines, vortex tubes, free and forced
vortex. [No. of Hrs.: 11]

UNIT II
Dynamics of Fluid Flow: Eulers equation of motion and its integration to yield Bernoulli’s
equation, graPrentice Hall Indiacal representation of Bernoulli’s equation and its
practical applications – Pitot tube, Venturi meter; steady flow momentum equation, force
exerted by jet on plane surface and force exerted on a pipe bend. [No. of Hrs.: 11]

UNIT III
Dimensional Analysis and Principles of Similarity: Buckingham π Theorem and its
applications, Geometric, Kinematics and Dynamic similarity; Dimensionless numbers-
Reynolds, Froude, Euler, Mach, Weber Number and their significance.
Boundary Layer Flow: Laminar and turbulent boundary Layer and laminar sublayer.
Boundary Layer thickness, displacement, momentum and energy thickness.
Laminar Flow : Reynold’s experiment, critical velocity, steady laminar flow through a
circular tube, flow between parallel plates, measurement of viscosity. [No. of Hrs.: 11]

UNIT IV
Turbulent Flow: Shear stress in turbulent flow. Hydrodynamically smooth & rough
boundaries. Velocity distribution for turbulent flow in smooth and rough pipes.
Analysis of Pipe Flow: Energy losses, minor losses in pipe lines, concept of equivalent
length, flow between two reservoirs, multiple pipe systems in series and parallel,
siphon. Flow Measurements: Measurement of flow using Venturi meter, orifice meter,
Pitot tube, Flow nozzle, Measurement of flow in open channels rectangular, triangular,
trapezoidal weir, Cipoeletti weir. [No. of Hrs.: 11]

TEXT BOOKS :
1. R.K. Basal, “Fluid Mechanics & Hydraulic Machines”, Laxmi Publications(P)
Ltd.,2002.
44
Effective from academic session 2008 - 09
2. D.S. Kumar, “Fluid Mechanics and Fluid Power Engineering”, S.K. Kataria &
Sons,2000.

REFERENCE BOOKS :
1. I.H. Shames, “Mechanics of Fluids”, Tata McGraw Hill, 1982.
2. V.L. Streeter and E.B. Wylie, “Fluid Mechanics”, Tata McGraw Hill
Practicals:

ETME – 251 Electronics Lab P C

Based on Course work ETME 203 2 1

ETME – 253 Mechanics of Solids/Fluid Mechanics Lab P C

Based on Course work ETME 207 and ETME 211 2 1

ETTE – 255 Machine Design & Drawing Lab P C

Based on Course work ETTE 209 2 1

ETTE - 257 Numerical Analysis & Programming Lab P C

Based on Course work ETTE 201 2 1

45
Effective from academic session 2008 - 09
Paper Code: ETME - 202 L TC
Paper: KINEMATICS & DYNAMICS OF MACHINES 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
General concepts, Velocity and Acceleration Analysis: Introduction of Simple
mechanism, Different types of Kinematics pair, Grublers rule for degree of freedom,
Grashof’s Criterion for mobility determination Inversions of 3R-P, 2R-2P chains,
Kinematic analysis of planar mechanism by graPrentice Hall Indiacal and vectorial
analysis. Computer Implementation of Kinematic analysis using C++.
[No. of Hrs.: 11]
UNIT II
Cams: Classification, Cams with uniform acceleration and retardation, SHM, Cylcloidal
motion, oscillating followers. Vibrations: Vibration analysis of SDOF systems, natural,
damped forced vibrations, basedexcited vibrations, transmissibility ratio.
[No. of Hrs.: 11]

UNIT III
Gears: Geometry of tooth profiles, Law of gearing, involute profile, interference, helical,
spiral and worm gears, simple, compound gear trains. Epicyclic gear trains – Analysis
by tabular and relative velocity method, fixing torque. Dynamic Analysis: Slider-crank
mechanism, turning moment computations. [No. of Hrs.: 11]

UNIT IV
Balancing: Static and Dynamic balancing, balancing of revolving and reciprocating
masses, single and multi-cylinder engines. Gyroscopes: Gyroscopic law, effect of
gyroscopic couple on automobiles, ships, aircrafts. [No. of Hrs.: 11]

TEXT BOOKS :
1. S.S. Rattan, “Theory of Machines”, Tata McGraw Hill, 2000
2. Dr. V.P. Singh, “Theory of Machines”, Dhanpat Rai & Co.(P)Ltd.,2001

REFERENCE BOOKS :
1. Jagdish Lal, “Theory of Mechanism & Machines”, Metropolitan Education,2000
2. Thomas Beven, “The Theory of Machines”, CBS Publishers, 2000
3. P.L. Ballaney, “Theory of Machines & Mechanism”, Khanna Publishers, 23rd Edition,
2003.
4. Malhotra & Gupta, “The Theory of Machine”, Satya Prakashan, 1999.

46
Effective from academic session 2008 - 09
Paper Code: ETTE - 204 L TC
Paper: FINITE ELEMENTS METHODS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Continuum and Discrete System
Finite Element Modeling: Local and Natural coordinates: 2-D and axi-symmetric
elements and shape functions, continuity and convergence. [No. of Hrs.: 10]

UNIT II
Higher Order Element: ISO-parametric elements, Numerical Integration
[No. of Hrs.: 10]

UNIT III
Finite Element Formulation: Potential Energy and weighted residual methods of
formulation.Assembly of global stiffness metric and load vector, Imposition of boundary
conditions. [No. of Hrs.: 10]

UNIT IV
Computer Implementation and Application of FEM: Method of solution of simultaneous
equations. Computer implementation of the method. Application of FEM to Heat
Transfer and Stress analyses problems. [No. of Hrs.: 10]

TEXT BOOKS :
1. Larry J. Segerlind, “Applied Finite-Element Analysis”, John Wiley, 1976.
2. Kenneth H. Huebner, “Finite Element Method for Engineers”, Wiley, 1975.

REFERENCE BOOKS :
1. O.C. ZienKiewicz, “The Finite Element Method”, Tata McGraw Hill, 1977.
2. S.S. Rao, “Finite Element Method In Engineering”, Pergaman Press, 1982.

47
Effective from academic session 2008 - 09
Paper Code: ETTE - 206 L TC
Paper: MACHINE TOOLS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Classification of machine tools based on application and production rate:
General purpose, Single purpose machines, Classification based on-types of machine
tools and the processes, Generating and forming.
Elements of metal cutting processes: Elements of tool geometry, cutting tool
materials and applications. [No of Hrs: 06]

UNIT II
Milling Machines: Types of general purpose milling machines: horizontal, vertical and
universal. Types of milling cutters and their applications, different milling operations,
work holding devices: vice, clamps, chucks, dividing head and its use, simple,
compound and differential indexing. Indexing calculations and machining time
calculations. Introduction to machining centers.
Lathe Machines :Types and classification of lathes: Specifications-method of holding
work and tool, accessories, attachments-operations and types of tools for each
operation, Capstan and Turret lathe. [No of Hrs: 08]

UNIT III
Reciprocating Type Machine Tools: Shaper, Planer and Slotter: Constructional
features, basic machines and kinematics and related calculations.
Drilling Machines: Types of drilling machines and their Constructional, feed mechanism,
work holding devices, Tool – holding devices. Different drilling operations: Drilling,
reaming, counter boring and countersinking etc., estimation of drilling time.
[No. of Hrs.: 08]

UNIT IV:
Grinding Machines: Different types of grinding machines: cylindrical, surface and
centre-less grinding machines, basic constructional features and mechanisms,
specifications, different grinding operations, honing, lapping and super-finishing
processes.
[No. of Hrs.: 08]
UNIT V
Special Purpose Machines : Introduction and applications.
[No. of Hrs.: 04]

TEXT BOOKS :
48
Effective from academic session 2008 - 09
1. P.N. Rao, “Manufacturing Technology: Metal Cutting & Machine Tools”, Tata McGraw
Hill, Delhi, 2004.
2. B.S. Raghuwanshi, “Workshop Technology”, Vol.2, Dhanpat Rai & Sons, 2003.
3. Hazra Chandhari S.K., “Elements of Workshop Technology”, Vol.2, Media Promoters,
2003.

REFERENCE BOOKS :
1. P.C. Sharma, “ATEXT BOOKS : of Production. Engineering”, S. Chand, New Delhi,
2004.
2. Bawa H.S., “Workshop Technology”, Vol.2, Tata McGraw Hill, 2004.
3. S.F. Krar Stevan F. and Check A.F., “Technology of M/C Tools”, McGraw Hill Book
Co., 1986.
4. Kibbe Richard et al, “M/c Tool practices”, Prentice Hall India, 2003.
5. Bangalore HMT, “Production Technology”, Tata McGraw Hill, 1980.
6. R.K. Jain, “Production Technology”, Khanna Publishers, 1986.
7. Gerling Heinrich, “All about Machine Tools”, New Age Publication, 2003.

49
Effective from academic session 2008 - 09
Paper Code: ETTE 208 L T C
Paper: BASICS OF AUTOMATION 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Basic concepts of automation: Automatic handling of parts, using relays, positioned
limit switches, etc hard automation of dedicated system of handling using in line
transfer, rotary transfer by Geneva mechanism, electro-hydraulic or pneumatic systems.
Product cycle, Manufacturing functions, Types of automation, Degree of automation,
Technical, Economic and human factors in automation. [No. of Hrs.: 08]

UNIT II
Technologies: Mechanical, Electrical, Hydraulic, Pneumatic, Electronic, Hybrid
systems, Comparative evaluation. Development of small automation systems using
mechanical devices, Basics of pneumatics, Synthesis of circuits, Basics of hydraulic
systems, Synthesis of hydraulic circuits. [No. of Hrs.: 11]

UNIT III
Circuit and System for Automations : Elements used for electrical circuits, Synthesis,
Circuit optimization techniques. Illustrative examples of the above types of systems as
well as hybrid systems used for automation of working cycles of machines, Material
Handling, Inspection and Assembly etc. [No. of Hrs.: 11]

UNIT IV
Controllers : Industrial logic control systems, Logic diagramming, Programmable
controllers, Applications, Designing for automation, Cost-benefit analysis.
[No. of Hrs.: 08]
TEXT BOOKS :
1. Gavrilov, A.N., “Automation and Mechanization of Production Processes in
Instrument Industry”, Pergaman Press, Oxford, 1967.
2. Pippenger John J., Tyler G., “Industrial Hydraulics”, MGH, New York, 1962.
3. Soundararajan V., “Introduction to Hydraulics and Pneumatic”, Prentice Hall of India,
2007.

REFERECE BOOKS :
1. Johnson, David G., “ Programmable Controllers for Factory Automation”, Marcel
Dekker, New York, 1987.
2. Boothroyd, G. and Poli, C., “Automatic Assembly”, Marcel Dekkar, New York, 1982.

50
Effective from academic session 2008 - 09
3. Sapiro, Steve Smith, Robert J., “Handbook of Design Automation”, Prentice Hall,
1986.
4. Fawcett J.R., “Pneumatic Circuits and Low Cost Automation”, Trad & Technica Press,
England, 1968.
5. Groover, Mikell P., “Automation, Production Systems and Computer Integrated
Manufacturing”, Prentice Hall, 1987.

Paper Code: ETTE 210 LTC

Paper: INDUSTRIAL MANAGEMENT AND QUALITY CONTROL 314
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Management : Definitions of management , history of management, types of
management, responsibilities, management task, the engineering manager,
Organization structures, the quality organization, organizational change, managing
change, Management obligations, social and professional responsibilities Personnel
management and administration, manpower planning, recruitment, selection and
training. Accidents, absenteeism and labour turnover. [No. of Hrs.: 08]

UNIT II
Industrial relations: objectives, causes results and settlement of industrial relations,
workers participation in management, collective bargaining, trade unions, principles of
industrial legislations, Wage payment plans-wage incentives. [No. of Hrs.: 04]

UNIT III
Financial management: financial accounts, inflation, profitability, budgets and controls,
obtaining finance, valuing a company, Control through costing: Cost accounting,
valuation of stocks, allocation of overheads, standard costing, marginal costing,
Investment decision: the ranking process, payback period, average rate of return,
discounted cash flow.
Project Management : Network construction & identification of critical activities in CPM
& PERT. Introduction to Optimization Techniques, Linear Programming and its graphical
solution. [No. of Hrs.: 10]

UNIT IV
Marketing and sales management : The market, marketing information, market
segmentation, consumer and industrial markets, Product management, pricing,
marketing communications, sales physical distribution, Entrepreneurship – concept
Entrepreneurship development, factors affecting, Entrepreneurship, project report and
techno economic feasibility assessment. [No. of Hrs.: 10]

UNIT V
Quality Management : Total Quality Management, Customer Orientation, Continuous
improvement, Approaches and philosophies of TQM, 7 quality control tools, statistical
process control, quality circle, quality cost, quality audit and reporting.

51
Effective from academic session 2008 - 09
Six sigma: definition, key elements of six sigma, advantages of implementing six sigma,
DMAIC – six sigma process. [No. of Hrs.: 06]

TEXT BOOKS :
1. Koontz & Donnel , “Principles of Management”, Mcgraw Hill, 1968,
2. Kotlar, P., “Marketing Management Planning And Control”, Macmillan India Ltd.,
2002.
3. Chandra, P., “Financial Management”, Tata Mcgraw Hill, 2000.
4. Dilworth, James B., “ Operation Management : Design, Planning and Control for
Manufacturing and Services, Mcgraw Hill , 1992.

REFERENCES BOOK
1. Bethel Lawrence, “Industrial Organisation and Management” , McGraw Hill, 1962.
2. Prasanna Chandra, “Financial Management”, TMH, 1989.
3. IM Pandey, “Financial Management” , Vikas Publisher, 1979.
4. Feigenbaum, “ Total Quality Control : Engineering and Management”, Mcgraw
Hill,1961.
5. J.S. Chandan, “Management: concept and Strategies”, Vikas Publishing House,
2002.
6. Babcock & Morse, “ Managing Engineering and Technology: An Introduction to
Management for Engineers”, PHI, 2007.
7. K.C.Arora, “ Total Quality Management”, S.K. Kataria & Sons, 2007.
.

52
Effective from academic session 2008 - 09
Paper Code: ETTE 212 L TC
Paper: ENGINEERING METALS AND METALLURGY 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Atomic structure of metals crystal structure, crystal lattice of (i) Body centered cubic (ii)
face centered cubic (iii) closed packed hexagonal, crystallographic notation of atomic
planes, polymorphism and allotropy, solidification of crystallization (i) nuclear formation
(crystal growth) (ii) crystal imperfection Elementary treatment of theories of plastic
deformation, phenomenon of slip twinning, dislocation, identification of crystallographic
possible slip planes and direction in FCC, BCC, C.P., recovery, re-crystallization,
preferred orientation causes and effects on the property of metals.
[No. of Hrs.: 08]
UNIT II
Introduction to Engineering materials, their mechanical behavior, testing and
manufacturing properties of materials, physical properties of materials, classification of
engineering materials.
General principles of phase transformation in alloys, phase rule and equilibrium
diagrams, Equilibrium diagrams of Binary system in which the components form a
mechanical mixture of crystals in the solid state and are completely mutually soluble in
both liquid state. [No. of Hrs.: 08]

UNIT III
Equilibrium diagrams of a systems whose components have complete mutual solubility
in the liquid state and limited solubility in the solid state in which the solid state solubility
deceases with temperature. Equilibrium diagram of alloys whose components have
complete mutual solubility in the liquid state and limited solubility in solid state(Alloy with
a peritectic transformation). [No. of Hrs.: 08]

UNIT IV
Equilibrium diagrams of a system whose components are subject to allotropic change.
Iron carbon equilibrium diagram. Phase transformation in the iron carbon diagram (i)
Formation of Austenite (ii) Transformation of austenite into pearlite (iii) Martensite
transformation in steel, time temperature transformation curves. [No. of Hrs.: 08]

UNIT V
Principles and applications of heat treatment processes viz. annealing, normalizing
hardening, tempering; harden ability & its measurement, surface hardening processes.
53
Effective from academic session 2008 - 09
Defects in heat treatment and their remedies; effects produced by alloying elements on
the structures and properties of steel. Distribution of alloying elements (Si, Mn. Ni. Cr.
Mo. TL. Al) in steel. [No. of Hrs.: 08]

TEXT BOOKS :
1. V. Raghavan, “Material Science & Engineering”, Prentice Hall India Ltd., 2001.
2. S.K. Hazra Chaudhuri, “Material Science & Processes”, Indian Book Publishers,
Calcutta, 1983.
3. R.B. Gupta, “Material Science Processes”, Satya Prakashan, New Delhi, 2000.

REFERENECE BOOKS :
1. Degarmo E. Paul et.al, “Materials & Processes in Manufacture”, Prentice Hall India,
New Delhi, 2001.
2. Raymond A Higgim., “Engineering Metallurgy Part 1”, Prentice Hall India, New Delhi,
1998.
3. L. Krishna Reddi, “Principles of Engineering Metallurgy”, New Age Publication, New
Delhi, 2001.
4. Buduisky et al, “Engineering Materials & Properties”, Prentice Hall India, New Delhi,
2004.
5. Peter Haasten, “Physical Metallurgy”, Cambridge Univ. Press, 1996.

54
Effective from academic session 2008 - 09
Practicals:

ETME - 252 Kinematics & Dynamics of Machines Lab. PC

Based on course work ETME 202 2 1

ETTE - 254 FEM Lab. PC

Based on course work ETTE 204 2 1

ETTE - 256 Machine Tools Lab. PC

Based on Course Work ETTE 206 2 1

ETTE – 258 Automation Lab. PC

Based on Course work ETTE 208 2 1

55
Effective from academic session 2008 - 09
Paper Code: ETTE 301 L TC
Paper: PRODUCTION PLANNING AND CONTROL 3 0 3
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
INTRODUCTION : Introduction to Production planning and control, functions of
production control, Types of production: Job, batch and continuous, Product
development and design: Marketing aspect, Functional aspects, Product development
and design: Operational aspect, durability and dependability, aesthetic aspect, Profit
consideration Standardization, Simplification & specialization, Break even analysis,
Economics of a new design. [No. of Hrs.: 08]

UNIT II
WORK STUDY : Method study, Introduction, Procedure Selection, Record, Analysis,
Development and Implementation, Micro motion and memo motion study, Work
measurement Introduction, Techniques of Work measurement, Time study, production
study, Work sampling, synthesis from standard data, PMTS (predetermined motion time
standards). [No. of Hrs.: 08]

UNIT III
PRODUCT PLANNING AND PROCESS PLANNING : Product planning : Introduction,
Extending the original product information, Value Analysis, Problems in lack of Product
planning, Process planning and routing – pre requisite information needed for process
planning, Procedural steps in Process planning, Quantity determination in batch
production, Machine capacity, balancing, Analysis of process capabilities in a multi
product system. [No. of Hrs.: 08]

UNIT IV
PRODUCTION SCHEDULING : Production control systems-Loading and Scheduling:
master scheduling – scheduling rules- Gantt charts, Perpetual loading – basic
scheduling problems, Flow, batch production scheduling, product sequencing,
Production control systems – periodic batch control, Material Requirement Planning,
kanban, Dispatching Progress reporting and expediting, Manufacturing lead time –
Techniques for aligning completion times and due dates. [No. of Hrs.: 08]

UNIT V
INVENTORY CONTROL AND RECENT TRENDS IN PPC : Inventory Control
Introduction, Purpose of holding stock, Effect of demand on inventories – Ordering
56
Effective from academic session 2008 - 09
procedures. Two bin, ordering cycle system, Determination of EOQ, economic lot size,
ABC Analysis, Recorder procedure, Introduction to CIPP systems, Elements of JIT,
Fundamentals of MRP II and ERP. [No. of Hrs.: 08]

TEXT BOOKS :
1.Martand Teslang, “Industrial Engineering and Production Management”, S. Chand
and Company. First edition, 2000.
2. S.K. Mukhopadhyay, “Production Planning and Control”, Prentice Hall of India, 2007.
REFERENECE BOOKS :
1. Samson Eilon, “Elements of production planning and control”, Universal Book Corp.
1984.
2. Elwood S. Buffa and Rakesh K. Sarin, “Modern Production/Operations Management”,
8th Edition, Wiley and Sons, 2000.
3. K. C. Jain, L.N. Aggarwal, "Production planning control and Industrial Management”,
Khanna Publishers, 1990.
4. N. G. Nair, “Production / Operations Management”, Tata- Mc Graw Hill, 1996.
5. S. N. Chary, “Theory and Problems in Production & Operations Management”, Tata
Mc Graw Hill, 1995.

57
Effective from academic session 2008 - 09
Paper Code: ETTE 303 LTC
Paper: METROLOGY AND QUALITY ASSURANCE 303
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Principles of measurement: Definition of Metrology, difference between precision and
accuracy. Sources of errors: Controllable and Random Errors, Effects of Environment
and Temperature, Effects of support, alignment errors.
Length Standards: Line standards, end standards and wavelength standards, transfer
from line standards to end standards. Numerical based on line standards. Slip gauges –
its use and care, methods of building different heights using different sets of slip
gauges.
Limits, fits and tolerances: Various definitions, different types of fits and methods to
provide these fits. Numerical to calculate the limits, fits and tolerances, ISO system of
limits and fits; Gauges and its types, limit gauges – plug and ring gauges. Gauge
Design – Taylor’s Principle, wear allowance on gauges.
[No. of Hrs.: 10]
UNIT II
Comparators: Principles and working of Mechanical, Electrical, Optical and Pneumatic
Comparators .Angular Measurement: Sine Bar – different types of sine bars, use of sine
bars in conjunction with slip gauges, Use of angle gauges, spirit level, errors in use of
sine bars. Numericals. Principle and working of autocollimator. [No. of Hrs.: 06]

UNIT III
Straightness and flatness: Definition of Straightness and Flatness error. Numericals
based on determination of straightness error of straight edge with the help of spirit level
and auto collimator Screw Thread Measurement: Errors in threads, Measurement of
elements of screw threads –major diameter, minor diameter, pitch, flank angle and
effective diameter (Two and three wire methods). Effect of errors in pitch and flank
angles. Gear Measurement: Measurement of tooth thickness – Gear tooth vernier
caliper, Constant chord method, base tangent method and derivation of mathematical
formulae for each method. Parkinson Gear Tester. [No. of Hrs.: 10]

UNIT IV
Machine Tool Alignment: Machine tool tests and alignment tests on lathe. Alignment
tests on milling machine. Alignment tests on a radial drilling machine, Interferometry.
Surface texture: Introduction, types of irregularities, Elements of surface. Texture,
Measurement of surface finish, Evaluation of surface Roughness. [No. of Hrs.: 06]
58
Effective from academic session 2008 - 09
UNIT V
Computer Aided Metrology : Principles and interfacing, software metrology. Laser
metrology - Applications of Lasers in precision measurements - Laser interferometer,
speckle measurements, laser scanners.
Coordinate Measuring Machine: Types of CMM, Probes used, Applications, Non
contact CMM using Electro optical sensors for dimensional metrology - Non contact
sensors for surface finish measurements. Image processing and its application in
Metrology. [No. of Hrs.: 06]

TEXT BOOKS :
1.R.K. Jain, “Engineering Metrology”, Khanna Publishers, Delhi, 2002.
2.I.C. Gupta, “Engineering Metrology”, Dhanpat Rai and Sons Publications, Delhi, 1994

REFERENECE BOOKS :
1.F.W. Galyer & C.R. Shotbolt, “Metrology for Engineers”, ELBS edition, 1990.

59
Effective from academic session 2008 - 09
Paper Code: ETTE 305 LTC
Paper: JIGS, FIXTURE & GAUGE DESIGN 31 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction to locating and clamping devices, difference between jigs and fixture,
advantages of jigs and fixture, materials used in jigs and fixture, locating principle,
locating methods and devices, standard parts, clamping – analysis of clamping forces,
tolerance and error analysis. Consideration of Safety factor while designing of Jig
Fixture and Gauge. [No. of Hrs.: 11]

UNIT II
Introduction to drill jigs, Economics of drill jig, General considerations in design drill jigs ,
types of drill jigs , Drill bushings, Method of constructions , clearance – handling
clearance, swarf and cutting fluid clearances, burr grooves Methods of inserting bushes,
Design Drill jigs for given components, Drill jigs and modern manufacturing.
[No. of Hrs.:
10]
UNIT III
Introduction to fixtures, Economics of fixtures, Types of fixtures & Application –
overview, Vise fixtures, milling fixtures , Boring fixtures, broaching fixtures , Lathe
fixtures, grinding fixtures, welding fixture , indexing fixture, Design of fixtures for the
given components. [No. of Hrs.: 08]

UNIT IV
Gauge design : introduction, Types of gauges, gauges tolerance , selection of materials
for gauges. Review of tolerance analysis, Taylors principle, ideal gauge. Design of plain,
Taper, Spline and thread Limit Gauge. Design of Positional gauges, Indicator, Flush pin
and Reciever gauges. Gauge manufacturing techniques. Case studies of gauges for
selected components. [No. of Hrs.: 11]

TEXT BOOKS :
1. P H Joshi, “Jigs and Fixture”, Tata Mcgraw Hill, New Delhi,2006.
2. Grant, “Jigs and Fixture : Non Standard Clamping Devices”, Mcgraw Hill, 1967.
3. Calvin, “Jigs and Fixture”, MGH Publication, 1948.

REFERENECE BOOKS :
1. Kempster, “Introduction to Jigs & Tool Design”, Viva Books Pvt Ltd,1998.

60
Effective from academic session 2008 - 09
2. Cyryll Donaldson, George H.Lecain, V.C. Goold, “Tool Design”, Tata Mcgraw Hill,
2002.
3. P H Joshi, “Tooling Data”, Wheeler Publication, 2005.

Paper Code: ETTE 307 L TC

Paper: CNC MACHINING & PROGRAMMING 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
An overview of CNC machines - need, benefits and limitations,
classification of CNC machines. Constructional features of CNC machines, types of
CNC machines, elements of CNC machine and systems, machine control unit, precision
measuring and positioning of CNC. [No. of Hrs.: 08]

UNIT II
CNC part programming: Process Planning and flow chart for part programming,
Preparatory codes G and Miscellaneous codes M, interpolation , tool compensation,
transformations, subroutines, special CNC control : geometry capability – scaling,
rotating, mirroring, copy etc, canned cycles for CNC lathe and milling, CNC program
verification tools, tool libraries for cutters
[No. of Hrs.: 12]

UNIT III
CNC Tooling : Tooling for milling, angle plates, CNC vises, work holding devices
clamps, rotary tables and rotary indexes, CNC cutting tools, Tool materials.
[No. of Hrs.: 11]
UNIT IV
CNC program generation from CAD, CNC controller and motion control in CNC system.
Applications of CNC and recent advances in CNC machines.
[No. of Hrs.: 08]

TEXT BOOKS :

1. T. K. Kundra, P.N. Rao and N. K. Tewari, “Numerical Control and Computer Aided
Manufacturing”, , Tata McGraw-Hill Publishing Co., New Delhi, , 2001
2. P.Radhakrishnan, S.Subramanyam and V.Raju, “CAD/CAM/CIM”, Publication Year: Oct,
2007, Edition: 3rd, Reprint: 2008.
3. Stenerson & Curran, “Computer Numerical Control: Operation and Programming”, Prentice
Hall of India, 2006.

REFERENECE BOOKS :
1. M. P. Groover, “Automation, Production Systems, and Computer-Integrated Manufacturing”,
Prentice Hall, Publication, July 2007
61
Effective from academic session 2008 - 09
2. M. Lynch, “Computer Numerical Control for Machining”, McGraw Hill Book Publishing
Company,1992.
3. J.S. Stenerson, “Computer Numerical Control: Operation and Programming”, Kelly Curran,
Publisher: Prentice Hall, 2007.
4. S.K. Sinha, “CNC Programming”, Galgotia Publications 2003.
5. James Madison, “CNC Machining Handbook”, Industrial Press Inc, 1996.

Paper Code: ETTE 309 L TC

Paper: Plastic Technology 3 14
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Polymer Science : Introduction to monomer and polymer, intermolecular forces,
chemical bonding.Polymerisation, Polymerisation techniques and mechanism,
molecular weight, molecular distribution, effect of molecular weight on processing and
properties.Nomenclature, sources of raw material, methods of polymerisation, general
properties, processing behaviour and enduse applications of the following :
Natural polymers, shellac , casine. [No. of Hrs.: 11]

UNIT II
Additives : fillers, antioxidants, thermal stabilisers, lubricants, plasticisers, toughening
agents, colourants, fire retardants, coupling agents, blowing agents, ultraviolet
stabilisers, antistatic agents, antiblocking agents, slip and antislip agents, processing
aids, mould releasing agents. [No. of Hrs.: 08]

UNIT III
Compression & transfer moulding : Compression moulding, fundamental
principles, bulk factor, flow properties , processing temperature , mould temperature
control , moulding pressure , press tonnage , processing limitations , curing time ,
influence of processing parameters on the quality of the moulding.
Injection moulding: Introduction,Types of injection moulding machines, injection
moulding machines specifications , projected area , plasticizing capacity , shot weight ,
type of locking systems , mould clamping. Press tonnage, influence of processing
parameters on the quality of the moulding. [No. of Hrs.: 11]

UNIT IV
Extrusion: Introduction,extruder parts,extrusion screw, design features, design
variables, extruder output, extrusion processing parameters, their effects on product,
extruder faults causes and remedies.
Extrusion of film, pipe, sheet, profile and coating - dies for different extrusion process.
[No. of Hrs.: 08]
UNIT V
Blow moulding: Introduction to blow moulding, types of blow moulding operations ,
extrusion blow moulding, injection blow moulding, stretch blow moulding ,types of blow
moulding machines, blow mould construction.

62
Effective from academic session 2008 - 09
Rotational moulding : Introduction to rotational moulding, rotational mould
construction.
Thermoforming: Introduction, thermoforming methods, thermoforming dies
thermoforming equipment description.
Advanced processing techniques: Reaction injection moulding, Structural foam
moulding, Resin transfer moulding. [No. of Hrs.: 11]

TEXT BOOKS :
1. P.A. Tres, “Designing Plastic Parts for Assembly”, Hanser Gardner Publications; 5th
edition, 2003
2. R.A. Malloy, “Plastic Part Design for Injection Molding: An Introduction”, Hanser
Gardner Publications, 1994.

REFERENECE BOOKS :
1. J.Rotheiser, “Joining of Plastics: Handbook for Designers and Engineers”, Hanser
Gardner Publications, 2004.
2. J.P. Beaumont, R. Nagel, R. Sherman, “Successful Injection Molding: Process,
Design, and Simulation”, Hanser Gardner Publications, 2002 .
3. Fisher, “Blow Moulding of Plastic”, Butterworth, 1976.
4. Baird, “Industrial Plastic : Basic Chemistry, Major Resins, Modern Industrial Process”,
Willcox, 1982.
5. Harper, “Handbook of Plastic Processes”, MGH Publication, 2006.
6. Powell, “Selection and Use of Thermo Plastic”, Oxford Press, 1977.

63
Effective from academic session 2008 - 09
Practicals:

ETTE -351 Metrology & Quality Assurance Lab PC

Based on Course Work ETME – 303 2 1

ETTE – 353 Jigs Fixture & Guage Design Lab PC

Based on Course work ETTE – 305 2 1

ETTE- 355 CNC Machining and Programming Lab PC

Based on course work ETTE 307 2 1

ETTE – Minor Project PC

(with a thrust on Design Innovation & Manufacturing) 4 2

ETTE – 359 Industrial/Practical Training PC

6 weeks training will be held after fourth semester. However, 0 2
Viva-Voce will be conducted in the fifth semester.

64
Effective from academic session 2008 - 09
Paper Code: ETTE 302 L T C
Paper: PRESS TOOL DESIGN- I 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Principles of Blanking and Piercing Dies: Basic Blanking or piercing operation,
Shearing Theory, calculation of cutting force, importance of cutting force, calculation of
stripping force , calculation of cutting clearance, importance of cutting clearance. Cost
analysis with a view on the quantity of production. [No. of Hrs: 10]

UNIT II
Introduction to various parts of Blanking and Piercing Dies: Function of Punch
Plate, Top Plate, Shank, Stripper Plate, Die plate, Guide pillar and Guide Bushes,
gages , stopper . Stock material utilization and strip layouts. Materials used for above
referred parts. Selection of Presses. [No. of Hrs: 10]

UNIT III
Bending Dies: Basic of Bending, bending stress, bend allowance curve, estimating Flat
Blank lengths, Introduction to Bending Dies to produce Bend components. Cost analysis
with a view on the quantity of production. Selection of Presses. [No. of Hrs: 10]

UNIT IV
Designing of Shearing Tools : Design of blanking, Piercing and Bending Dies.
[No. of Hrs: 08]

TEXT BOOKS :
1. P.H. Joshi, “Press Tool Design and Construction”, Wheeler Publishing, Delhi, 2000.
2. Eary Reed, “Technique of Press Working Sheet Metal”, Prentice Hall, 1974.

REFERENECE BOOKS :
1. Joshi, “Machine Tools Handbook : Design and Operation”, Mcgraw Hill, 2008.
2. Ostergaard, “Basic Die Making”, MGH, NewYork, 1993.
3. Oehler, “Hydrualic Presses”, Arnold Press, 1968.
4. Makelt, “Mechanical Presses”, Arnold Press, 1968.

65
Effective from academic session 2008 - 09
Paper Code: ETTE 304 L TC
Paper: MOULD DESIGN - I 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Injection Mould design concepts : Introduction, concept of design, design principles,
parting line, mould elements, types of moulds, construction of core and cavities, position
of gate, gate balancing. Ejection, types of ejections, mould cooling, mould alignment,
ancillary parts of the mould, consideration of safety factor while designing.
[No. of Hrs:
06]

UNIT II
Shrinkage : material shrinkage properties, amorphous, crystalline and semi- crystalline
materials behavior, shrinkage Vs tolerance, minimum wall thickness, creep properties,
mechanical properties and load bearing requirements. [No. of Hrs: 08]

UNIT III
Moulding machines : Selection of machines, specifications of machines, shot capacity,
plasticising capacity, nozzle details, minimum daylight, maximum daylight, ejection
arrangement, dry cycle time, their applications in mould design, deciding number of
impressions, types of machines, types of machines and their operation, special
attachments of the moulding machines.
Types of moulds: Two plate mould, direct sprue injection, single impression, multi
impression, side gated, three plate moulds, stack moulds, multi day light moulds.
Split moulds, external undercut, internal undercut, delayed action, cam track actuation,
hydraulic core pulling devices, split cavities, split cores, threaded inserts, internal and
external. [No. of Hrs: 12]

UNIT IV
Methodical approach to mould design, determination of economical number of cavities,
mould standards bolsters, standard mould parts, mould design check list. Cost
estimation and cost analysis.
Product design: Product design concepts – size, shape, function, aesthetics, life,
tooling aspects on product design, process variables Vs product design, product design
thumb rules for plastics, cost reduction through product design concepts, design of
external, internal undercuts, side openings, hinges, fits of box and lid, assembly through
resilience properties, case studies. [No. of Hrs: 08]

UNIT V
Theromsetting and Thermosets : Introduction, different type of thermosets,
thermosets as fillers.
[No. of Hrs: 04]
TEXT BOOKS :
1. R.J.W. Pye, “Injection Mould Design”, Affilated West Press, Delhi, 2000.
2. Rosato, “Injection Molding HandBook”, CBS Publishers, Delhi, 1987.
66
Effective from academic session 2008 - 09
3. Irvin I Rubin, “Injection Moulding Theory & Practice”, John Willey, 1972.
Paper Code: ETTE 306 L TC
Paper: RAPID PROTOTYPING & REVERSE ENGINEERING 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Review of solid modeling techniques with comparison advantages and disadvantages.
Basic principle of RP processes, classification of RP processes, various Industrial RP
systems like Sterolithography, Fused Deposition Modeling , Selective Laser Sintering,
Laminated object Manufacturing, 3 D Printing, Ballistic particle Modeling etc.
[No. of Hrs.:
11]
UNIT II
Role of Rapid Prototyping and Rapid Tooling in product development and simultaneous
engineering. Process planning for rapid prototyping, STL file generation defects in STL
files and repairing algorithms, slicing and various slicing procedures, Accuracy issues in
Rapid Prototyping , Strength of RP parts, Surface roughness problem in RP.
[No. of Hrs.: 08]
UNIT III
Part deposition orientation and issue like accuracy, surface finish, build time, support
structure, cost etc. Rapid tooling technique such as laminated metallic tooling, direct
metal laser sintering, vacuum casting [No. of Hrs.: 08]

UNIT IV
Introduction to reverse engineering. Selecting and optimally employing 3-D digitization
strategies and systems. Efficiently using 3-D scanning & CAD model development for
complex components and tools. Performing variance analysesr of geometry models.
Developing customized reverse engineering processes. Rapidly generating CAD
models of concrete objects (external and internal geometries). [No. of Hrs.: 12]

TEXT BOOKS :
1. Rafiq Noorani, “Rapid Prototyping: Principles and application”, John Wiley, Hoboken,
2006.
2. Franck W. Liou, “Rapid Prototyping and Engineering Application : A TEXT BOOK for
Prototype Development”, Taylor & Francis Publication, 2008.
3. Kevin Otto and Kristin Wood, “Product Design : Technology in Reverse Engineering
and New Product Development”, Pearson, New Delhi, 2004.

REFERENECE BOOKS :
1. Pham D.T. , Dimov S.S. , “Rapid Manufacturing : Technology & Applications of Rapid
Prototyping and Rapid Tooloing”, Springer – Verlag, London, 2001.
2. Patri K. Venuvinod and Weiyin Ma, “Rapid Prototyping : Laser based and other
Technology”, Kluwer, Boston, 2004.
3. Kai, Chua Chee, Fai Leong, “Rapid Prototyping : Principle & Application in
Manufacturing”, John Willey, London, 2003.

67
Effective from academic session 2008 - 09
Paper Code: ETTE 308 L TC
Paper: METAL CUTTING & TOOL DESIGN 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Definition of feed, depth of cut and cutting speed. Concept of specific
cutting energy in metal cutting and Numerical based on calculation of machining time on
lathe, drilling machine, shaper, milling machine and grinding machines considering
specific cutting energy of materials.
Theory of Metal Cutting: Orthogonal and oblique cutting, types of chips, Factors
affecting the chip formation, Cutting forces in orthogonal cutting and their measurement,
Merchant circle and derivation of relationships between the cutting forces, chip
thickness ratio, shear angle, stress and strain in the chip, work done and power required
in metal cutting, plowing forces and the ‘sizeeffect’,apparent mean shear strength of
work material. [No. of Hrs.: 11]

UNIT II
Ernst Merchant Theory: its assumptions and modifications. Relationship between
cutting velocity, shear velocity and chip flow velocity. Mechanism of friction at chip-tool
interface. Numerical problems based on metal-cutting.
Heat generation in Metal cutting: Heat generation and temperature distribution in
metal cutting. Calculation of temperature in primary and secondary deformation zones
and their measuring methods. [No. of Hrs.: 11]

UNIT III
Machinability: Machinability and its criteria, forms of tool-wear in metal cutting, tool-life
and its criteria, effect of different cutting parameters on tool-life. Economics of
machining and numericals. Cutting fluids, their physical action and applications.
Grinding: Specifications of grinding wheel, Mechanics of grinding, effect of grinding
conditions and type of grinding on wheel behaviour, equivalent diameter of grinding
wheel. [No. of Hrs.: 08]

UNIT IV
Cutting Tool Design: General considerations, single point tool geometry. Principles of
different cutting tool materials and their important characteristics. Geometry of a drill.
Basic principles of design of a single point and multiple point tools i.e broaches and
twist drill. [No. of Hrs.: 08]

TEXT BOOKS :
1. Dr. P.C. Pandey & C.K. Singh, “Production Engg. Sciences”, Standard Publisher.
Distributors, 2005.
68
Effective from academic session 2008 - 09
2. Dr. B.J. Ranganath, “Metal Cutting & Tool Design” Vikas Publishing House Pvt. Ltd,
1993.

REFERENECE BOOKS :
1. Geoffrey Boothroyd, “Fundamentals of Machining & Machine Tools”, Tata
McGraw Hill Kogakusha Ltd, 1987.
2. P.N. Rao, “Manufacturing Technology”, Tata McGraw Hill Publication Ltd, 2008.

69
Effective from academic session 2008 - 09
Paper Code: ETTE 310 L T C
Paper: CONCURRENT ENGINEERING 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer typequestions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Product life cycle, quality products, evaporative markets, globalization and Concurrent
engineering. Review of concurrent engineering techniques like DFM (design for
manufacture). DFA (design for assembly), QFD (quality function deployment), RP (rapid
prototyping), TD (total design) for integrating these technologies. [No. of Hrs.: 08]

UNIT II
Product information systems and their architecture. Information environment for
suppliers, management, testing & inspection design engineering, purchasing, process
control, manufacturing, support plans, operators, quality control, servicing and
maintenance. [No. of Hrs.: 11]

UNIT III
Product information modeling. Integration of information models and end users
applications. Computer aided simultaneous engineering systems. Integrated concurrent
design and product development. [No. of Hrs.: 11]

UNIT IV
Constraint networks. created by capacity expansion and professional resource
expansion. Case studies, DYNAMO, STELLA and SD based management games.
[No. of Hrs.: 08]

TEXT BOOKS :
1. Biren Prasad, “Concurrent Engineering Fundamentals : Integrated Product and
Process Organization”, Prentice Hall, New Jersey, 1997.
2. C.G. Miller, “Concurrent Engineering Design: Integrating the Best Practices for
Process Improvement”, Society of Manufacturing Engineers, Landon, 1993.

REFERENECE BOOKS :
1. M. Helander, M. Nagamachi, “Design for Manufacturing a Systems approach to
Concurrent Engineering and Ergonomics”, Taylor & Francis, London, 1992.
2. D.D. Bedworth, M.R. Henderson and P.M. Wolfe, “Computer Integrated Design and
Manufacturing”, McGraw Hill, 1991. .

70
Effective from academic session 2008 - 09
Paper Code: ETTE 312 L T C
Paper: VALUE ENGINEERING 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer typequestions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction to Value Engineering (V.E.) and Value Analysis, Life Cycle of a Product,
Methodology of V.E., Quantitative definition of Value,Use Value and Prestige Value,
Estimation of product quality/performance. [No. of Hrs.: 11]

UNIT II
Types of Functions, Relationship between Use Functions and Esteem Functions in
product design, Functional Cost and Functional Worth, Effect of value improvement on
profitability, Aims of VE systematic Approach. Introduction to V.E. Job plan / Functional
Approach to Value Improvement, Various phases and techniques of the job plan.
[No. of Hrs.: 08]

UNIT III
Factors governing project selection, Life Cycle Costing for managing the Total Value,
Concepts in LCC, Present Value concept, Annuity concept, Net Present Value, Pay
Back period, Internal rate of return on investment (IRR), Examples and illustrations.
Creative thinking and creative judgement, False material, labor and overhead saving.
[No. of Hrs.: 11]
UNIT IV
System Reliability, Reliability elements in series and parallel, Decision matrix,
Estimation of weights and efficiencies, Sensitivity analysis, Utility functions, Fast
diagramming, Critical path of functions, DARSIRI method of value analysis, Purchase
price analysis. [No. of Hrs.: 08]

TEXT BOOKS :
1. S.S. Iyer , “Value Engineering”, New Age International, New Delhi, 2009.
2. Miles, Lawrence D., “Technology of Value Analysis And Engineering”, Mcgraw Hill,
1961.
3. American Society of Tools and Manufacturing Engineers, “Value Engineering in
Manufacturing”, Prentice Hall, 1967.

REFERENECE BOOKS :
1. Mudge Arthur E., “Value Engineering : Systematic Approach”, Mcgraw Hill, New York,
1971.
2. Raven A.D., “Profit Improvement by Value Analysis, Value Engineering and Purchase
Price Analysis”, Cassel, London, 1971.
3.Claswon, H. Robert, “Value Engineering for Management”, Auerbach, 1970.

71
Effective from academic session 2008 - 09
4.Oughton, Fredrick, “Value Analysis And Value Engineering”, Pitman, London, 1969.

Paper Code: ETTE 314 L T C

Paper: ERGONOMICS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Objective : To develop awareness, acquire information, and experience human factors
in design. Datalogging, data collection, data reduction and data analysis techniques.
[No. of Hrs.: 08]

UNIT II
Gross human anatomy, anthropometry, biomechanics, muscle strength and exertion
potential of different limbs, work capacity, environmental effects. Exercises for
evaluation of postural forms and work spaces. [No. of Hrs.: 08]

UNIT III
Environmental conditions including temperature, illumination, noise and vibration.
Perception and information processing, design of displays, hand controls, typography
and readability, layout and composition. [No. of Hrs.: 08]

UNIT IV
Exercises in evaluation of human response to product interface. Product safety and
products liability. Legal and safety issues, Various case studies. [No. of Hrs.: 08]

TEXT BOOKS :
1. D.C. Alexgander, “Applied Ergonomics” Taylor and Francis, 2001.
2. Pulat, B.Mustafa, “Fundamental of Industrial Ergonomics”, Prentice Hall, 1992.
3. Martino, Vittorio,Di , “Work Organization & Ergonomics”, ILO Genava, 1998.

REFERENECE BOOKS :
1. Mark R. Letho and James R. Buck, “Introduction to Human Factors and Ergonomics
for Engineers”, Taylor and Francis, New York, 2007.
2.Phillips, Chandler Allen, “Human Factor Engineering”, John Willey & Sons, New York,
2000.
3. Franus, Edward A., “Connective Networks in Ergonomics : General Methodological
Consideration”, Elsevier, Amesterdam, 1991 .
4. Kvalseth, Tarald O., “Ergonomics of Workstation Design”, Butterworths, London,
1985.
5. Mark R. Lehto and James R. Buck, “Introduction to Human Factors and Ergonomics
for Engineers”, Taylor and Francis, New York, 2007.

72
Effective from academic session 2008 - 09
Paper Code: ETTE 316 L TC
Paper: PRECISION ENGINEERING 3 14
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction to precision, machine design, principal of accuracy,repeatability and
precision. Errors due to geometry, kinematics, thermal expansion, dynamic forces and
instrumentation etc. [No. of Hrs.: 08]

UNIT II
System design considerations in precision engineering. Rollingand sliding contacts
bearings, hydrostatic and magnetic bearings, precision gears, positioning mechanisms
and drives. Electro magnetic piezoelectric and fluid actuators. [No. of Hrs.: 08]

UNIT III
Microelectro-mechanical systems, precision measurement and control devices, three
dimensional coordinate measuring machines, surface finish measurement. Precision
machining and finishing operations. Assembly and tolerancing. [No. of Hrs.: 08]

UNIT IV
MIcromaching systems. Tribological vibrations and noise considerations in high speed
mechanical units. Case studies from some of the application like computer drives,
printers, sewing machines, video and audio recorders, optical devices etc.
[No. of Hrs.: 08]

TEXT BOOKS :
1. M.V.Suryaprakash, “Precision Engineering”, Narosa Publishing House, 2004.
2. Nakazawa Hironm, “Principal of Precision Engineering”, Oxford University, Oxford,
1994.
3. A. Davidson, “Handbook of Precision Engineering”, Macmillan, London, 1970.

REFERENECE BOOKS :
1. Slocum, Alexender H. , “Precision Machine Design”, Prentice Hall, 1992.
2. David Dornfeld and Dae Eun Lee, “Precision Manufacturing”, Springer Science –
Business Media, 2007.
3. A.W. Judge, “Engineering Precision Measurement”, Chapman, London, 1950.

73
Effective from academic session 2008 - 09
Paper Code: ETTE 318 L TC
Paper: STATISTICAL QUALITY CONTROL 3 14
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Definition and Need of quality, Aspects of quality, Quality characteristic,
Quality specification, Quality function, Economics of quality. Inspection, Its objectives
and types, Inspection versus Quality Control, Statistical Quality Control, its Tools,
Advantages, limitations and Applications. [No. of Hrs.: 08]
UNIT II
Fundamentals of the theory of probability: objectives and applications; variable and
attributes, fundamentals concepts; patterns of variation, frequency distribution; cells and
cell boundaries, cumulative frequency distribution, the normal distribution, average,
measure of dispersion, statistical concept of universe. Binomial distribution, mean and
standard deviation, Poisson distribution as an approximation to the binomial, use of
tables for solving Poisson problems. [No. of Hrs.: 08]
UNIT III
Shewhart’s control charts for variables: X bar and R charts, relationship between
sample parameters and universe parameters, control limits for X bar and R charts,
examples of processes in control, examples of processes out of control, process
capability. Control chart for fraction defective: necessary steps for selection of sub
groups, choice between p chart and np chart, control limits, charts showing control and
lack of control, sensitivity of the p chart. Control charts for defects: control limits for c
charts; preparation and use of c charts. [No. of Hrs.: 08]
UNIT IV
Acceptance sampling : lot by lot acceptance using single sampling by attributes,
operating characteristics curves, producer’s risk, consumer’s risk, AOQL, LTPD, quality
protection, selection of sampling plans, choice of sampling plans to minimize average
total inspection, ATI curves, double and sequential sampling plans, concept of AQL.
[No. of Hrs.: 08]
UNIT V
Life testing and reliability: concept & definition of reliability, analysis of life test,
failure distribution- probability of equipment failure, conventional model, failure rate,
MTBF, OC curves ,exponential reliability function, series, parallel, and combinational
reliability, redundant system, maintainability, and availability. [No. of Hrs.: 08]
TEXT BOOK :
1. EL Grant & RS Leavenworth, “Statistical Quality Control”,McGraw Hill & Co, 1988.
2. O.P. Khanna, “Statistical Quality Control”, Dhanpat Rai & Co, 2001.

74
Effective from academic session 2008 - 09
3. R.C. Gupta, “Statistical Quality Control”, Khanna Pulishers, 2001.
4. L S Srinath, “Reliability Engineering”, Affiliated East West Press Ltd, 2005.
REFERENCE BOOKS:
1. Amitav Mitra, “Fundamentals of Quality Control and Improvement”, PHI 2 nd Ed., 1998.
2. Feigenbaum, “Total Quality Control , Vol 2(revised ed).”, McGraw Hill & Co, 1991.
Practicals:

ETTE - 352 Press Tool Design - I Lab PC

Based on course work ETTE 302 4 2

ETTE – 354 Mould Design - I Lab PC

Based on Course work ETTE 304 4 2

ETTE - 356 Rapid Prototyping & Reverse Engg. Lab PC

Based on Course Work ETTE 306 4 2

ETTE – 358 Metal Cutting & Tool Design Lab PC

Based on Course work ETTE 308 4 2

75
Effective from academic session 2008 - 09
Paper Code: ETTE – 401 L TC
Paper: CAD & PRODUCT DESIGN 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Fundamentals of CAD: Role of computers in design, geometric modelling- wireframe
and solid, modelling, engineering analysis - FEM, design review and evaluation,
automated drafting, design data base, softwares used in CAD, data exchange between
CAD and CAM. Fundamentals of CAM: Definition of automation, levels of automation,
high volume discrete parts production, Detroit type of automation, transfer machines,
analysis of automated flow lines, assembly machines, flow line balancing, line
balancing. [No. of Hrs.: 08]
UNIT II
Geometric Modeling : Modeling of Curves , Splines, parametric curves, Bezier and B-
spline curves, Modeling of surfaces: ruled surfaces and surfaces of revolution. Modeling
of Solids and their properties: Surfaces and curves in solids, Intrinsic and global
properties, feature based modeling, Characteristic tests and Intersections.
[No. of Hrs.: 08]
UNIT III
Solid Modeling: Data structures and Boolean operations. Computer Graphics Display
Interface: Modeling transformations, Viewing transformations, Projections, Clipping,
Hidden line/surface elimination, shading and light sources, Double buffering, Hardware
graphics engines. [No. of Hrs.: 08]

UNIT IV
Computer-aided drafting, Parametric drafting, Design visualization, Integration with NC
machines and manufacturing. Scientific Visualization: Animation, physical principles.
Graphics Standards: 2D and 3D standards and graphics portability. Introduction to
Product data standards and data structures database integration for CAD/CAM.
Consideration of safety while product designing on CAD. [No. of Hrs.: 08]
UNIT V
Product design with the help of above stated units & ETTE 357. [No. of Hrs.: 08]

TEXT BOOKS :
1. Groover and Zimmer, “CAD / CAM : Computer Aided Design & Manufacturing”,
Prentice Hall, 1984.
2. D. Hearn , M.P. Baker, “Computer Graphics , C Version”, Prentice Hall, 1997.
3. D. D.Voisinet, “Introduction of Computer Aided Drafting” by McGraw Hill Co, 1983.
4. S. Harring Ton, “Computer Graphic”, Mc Graw Hill Publisher, 1987.
5 P.N. Rao, “CAD/CAM Principles and Applications”, Tata McGraw Hill, 2003.
76
Effective from academic session 2008 - 09
REFERENECE BOOKS :
1. D.F Rogers, “Procedural elements for computer graphics”, TMH Publisher, 1985.
2. Rogers, D. F. and Adams, A., “Mathematical Elements for Computer Graphics”,
McGraw-Hill Inc., NY, 1989.
3. I. D. Faux and M. J. Pratt, “Computational Geometry for Design and Manufacture”,
John Wiley and Sons, NY, 1979.
4. M. E. Mortenson, “Geometric Modelling”, John Wiley and Sons, NY, 1991.
5. Mikell P. Groover, Emory W.Zimmers, “CAD/CAM”, Pearson Education, 2001.
6. Karl T Ulrich, Steven D Eppinger, “Product Design And Development” , TATA
MGRAW HILL, 2004.

77
Effective from academic session 2008 - 09
Paper Code: ETME - 403 L TC
Paper: MECHATRONICS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Overview: Mechanical Actuation System – Kinematic Chains, Cam, Gear,
Train Ratchet Mechanism, Belt, Bearing. Hydraulic And Pneumatic Actuation Systems:
Overview: Pressure Control Valves, Cylinders, Direction Control Valves, Rotary
Actuators, Accumulators, Amplifiers, and Pneumatic Sequencing Problems.
[No. of Hrs.: 11]

UNIT II
Electrical Actuation Systems: Switching Devices, Mechanical Switches – SPST, SPDT,
DPDT, Debouncing keypads; Relays, Solid State Switches, Diodes, Thyristors,
Transistors, Solenoid, Types Devices: Solenoid Operated Hydraulic and Pneumatic
Vlaves, Electro-Pneumatic Sequencing Problems. Control of DC Motors, Permanent
Magnet DC Motors, Control of DC Motors, Bush less Permanent Magnet DC Motors,
AC Motors, Stepper Motors, Stepper Motor Controls, Servo Motors. Interfacing
controllers: Interfacing, Buffers, Darlington Pair, I/O Ports, Interface Requirements,
Handshaking, Serial and Parallel Port Interfacing, Peripheral Interface, Adapters.
Digital logic: Number Systems, Binary Mathematics, Boolean Algebra, Gates and
Integrated Circuits Like 7408, 7402, Karnaugh Maps, Application of Logic Gates as:
Parity Generators, Digital Comparators, BCD to Decimal Decoders, Flip Flops.
Introduction to Microcontroller – Intel 8051, Selecting a Microcontroller.
Sensors and transducers and application: Performance Terminology, Static and
Dynamic Characteristics, Displacement, Position and Proximity Sensors, Potentiometer
Sensors, Strain Gauge Element, LVDT, Optical Encoders, Pneumatic Sensors, Hall
Effect Sensors, Tachogenerators, Strain Gauge Load Cell, Thermostats, Photo
Darlington. Interfacing Sensors in Mechantronic System as – Temperature Switch
Circuit, Float Systems. [No. of Hrs.: 12]

UNIT III
Introduction to signal conditioning: Signal Conditioning Processes, Inverting Amplifiers,
Non Inverting Amplifiers, Summing, Integrating, Differential, Logarithmic Amplifiers,
Comparators, Amplifiers Error, Filtering, wheatstone Bridge, Temperature
Compensation, Thermocouple Compensation, Analog to Digital Conversion, Digital To
Analog Conversion, Sample and Hold Amplifiers, Multiplexers, Time Division
Multiplexing, Data Acquisition, Digital Signal Processing, Pulse Modulation.
System models: Mechanical System Models Applications like – Machine on a floor, Car
Wheel Moving along a road etc. Model Development of an Electrical Systems, Fluid

78
Effective from academic session 2008 - 09
System, and Thermal Systems: Rotational – Translation Systems, DC Motors, Speed
Control and Hydraulic – Mechanical Systems. [No. of Hrs.: 11]

UNIT IV
Programmable logic controllers (plc):PLC Structure, Input / Output Processing,
Programming, Language (Ladder Diagram), Logic Functions, Latching, Sequencing,
Timers, Internal Relays and Counters, Shift Registers, Master and Jump Controls,
Jumps, Data Movement, Code Conversion, Ladder Circuits. Case studies: Auto-Focus
Camera, Printer, Domestic Washing Machine, Optical Mark Reader, Bar Code Reader
and Pick and Place robot Arm. [No. of Hrs.: 11]

TEXT BOOKS :
1. W. Bolton, “Mechatronics”, Pearson Education Ltd., 2003.

REFERENCE BOOKS :
1. Mohammad Ali Mazidi Janice Gillispier Mazidi, “The 8051 Microcontroller”, Pearson
Education Inc.,2004.
2. Gary Dunning, “Introduction to Programmable Logic Controllers”, Thomson Asia P.
Ltd., Singapore, 1998.
3. Gopal K. Dubey, “Fundamentals of Electrical Drives”, Narosa Publishing House,
2001.
4. Charles H. Roth, “Jr. Fundamentals of Logic Design”, Jaico Publishing House, 2001.
5. "HMT Mechatronics”, Tata McGraw Hill Publishing Co. Ltd., 2001.
6. Devdas Shetty, Richard A. Kolk “Mechatronics System Design”, Thomson Asia Pvt.
Ltd., Singapore, 2001.
7. A.K. Tayal, “Instrumentation & Mechanical Measurements”, Galgotia Publication
Pvt.Ltd., 2003.
8. D. Rana Durgaiah, “Fluid Mechanics & Machinery”, New Age Int. Publishers, 2004.
9. Nitaigour Premchand Mahalik, “Mechatronics Principles, Concepts & Application”,
Tata McGraw Hill Publishing Co.Ltd., 2003.
10. Mikell P. Groover, “Automation, Production Systems and Computer-Integrated
Manufacturing”, 2nd Edition, Prentice Hall, 2001.

79
Effective from academic session 2008 - 09
Paper Code: ETTE 405 L TC
Paper: PRESS TOOL DESIGN – II 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Compound Dies & Progressive Dies : Definition of Compound dies, introduction to
Compound ies, function of various parts of Compound dies, Definition of Progressive
dies, introduction to the progressive dies, calculation of centre of pressure, strip layouts.
[No. of Hrs.: 10]

UNIT II
Forming theory. Flow limit diagram. Deep drawing process, deformation, blank
development range of draw, drawability, strain factor, force calculation, wrinkling
Erickson test, defects in drawing. [No. of Hrs.: 10]

UNIT III
Failures in forming and drawing. Analysis and Remedies. Cost analysis with a view on
the quantity of production. consideration of safety, manufacturing methods of forming.
Drawing dies tolerances.
Reconditioning and repair of tools. Importance of safety. Fine blanking process
techniques and application.
Use of CAD for design of Press Tools: Work Piece checks, Find developed
Length/Blank Size, Nesting, Strip layout Progressive Dies. Case studies on Press Tools.
[No. of Hrs.:
11]

UNIT IV
Spring Design and calculations : Spring properties, spring materials, springs in die
design, helical compression spring, calculation of compression spring, flat sprongs, hot
wound spring selection of springs.
[No. of Hrs.: 04]
UNIT V
Extrusion: Cold Extrudable materials, cold extrusion equipment used, power
requirements lug preparation, extrusion pressure, lubricants, tools, design and extruding
dies, design of die elements. [No. of Hrs.: 06]

TEXT BOOKS :
1. P.H. Joshi, “Press Tool Design and Construction”, Wheeler Publishing, Delhi, 2000.
80
Effective from academic session 2008 - 09
2. Eary Reed, “Technique of Press Working Sheet Metal : An Engineering Approach to
Die Design”, Prentice Hall, 1974.

REFERENECE BOOKS :
1. Ostergaard, “Basic Die Making”, MGH, NewYork.,1993
2. Oehler, “Hydrualic Presses”, Arnold Press, 1968.
3. Makelt, “Mechanical Presses”, Arnold Press, 1961.
Paper Code: ETTE 407 L T C
Paper: MOULD DESIGN – II 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Parting line: Plain surface, stepped parting line, irregular parting surface, angled
surface, local stepped and profile parting surface, complex edge forms, venting.
Feed system: Sprue, runner and gate, determination of runner size and cross section,
layout of runners, balancing of runners, types of gates, application of gates to various
products/materials. [No. of Hrs.: 08]

UNIT II
Ejection: Types of ejection - pin ejection, stepped pin part pin, `D' pin, blade ejection,
sleeve ejection, stripper ejection, air ejection, double ejection, calculation of ejection
force required. [No. of Hrs.: 08]

UNIT III
Mould temperature control: Mould cooling methods – integral cooling circuit, baffle
cooling, spiral insert cooling, cooling through heat pipes, capillary tubes, heat rods and
its applications. Mould temperature, melt temperature, heat removal, re - calculation of
cooling time, case studies. [No. of Hrs.: 08]

UNIT IV
Thermosetting Mould design – Introduction to Transfer Moulding, transfer moulding
process, design consideration for transfer moulding, inserts, cavities and core, defects
and remedies, polishing and plating. [No. of Hrs.: 08]

TEXT BOOKS :
1. R.J.W. Pye, “Injection Mould Design”, Affiliated West Press, Delhi, 2000.
2. Rosato, “Injection Molding HandBook”, CBS Publishers, Delhi, 1987.
3. Irvin I Rubin, “Injection Moulding Theory & Practice”, John Willey, 1972.

81
Effective from academic session 2008 - 09
Practicals:

ETME- 451 CAD & Product Design Lab P C

Based on course work ETTE 401 2 1

ETME -453 Mechatronics Lab. P C

Based on Course Work ETME 403 2 1

ETTE – 455 Press Tool Design - II Lab. P C

Based on Course work ETTE 405 4 2

ETME – 457 Mould Design - II Lab P C

Based on Course work ETTE 407 4 2

ETTE – 459 PROJECT PART – I P C

(Project Planning & Appraisal) 8 4
Project Definition : Venture analysis, Project management Features;
Project organisation design; Operation planning and resource allocation; Plant location
analysis models; Project scheduling; Gantt charts;Analysis of project networks - PERT
and CPM. Scheduling under Resources constraint, Cash scheduling to multi-projects
situation Project monitoring and control aspects; Decision making theories in
Management under certainty, risk, uncertainty and competitive situations;
applications of the methodologies and formulations in such project decision making
problem solutions; Project capital, cost estimation; Breakeven Analysis, Cost Benefit
Analysis; Profitability Analysis, Commercial and notional profitability.

Project Engineering, procurement, storage and construction functions and other related
management problems; Project wind up and technological obsolescence; Computer
aided Project Management.

ETTE - 461 Industrial/Practical Training P C

6 weeks training will be held after sixth semester. 0 2
However, Viva-Voce will be conducted in this semester.

82
Effective from academic session 2008 - 09
Paper Code: ETTE 402 L TC
Paper: DIE CASTING & DIE DESIGN 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction : Die casting die, understanding the properties of Aluminium & Zinc alloys,
the significance of constituents an impurities and the importance of metallurgical
structures. The behavior of alloys and solid solutions during and after solidification.
Die casting Machine ; working principle of die casting machine, difference between
cold and hot chamber machines. [No. of Hrs.: 08]

UNIT II
Die casting dies : specific details of die construction, casting ejection, cores slides, and
loose die pieces, core actuating and locking devices, classification of dies , general
details of die design, die layout, die making techniques.
Therotical and practical aspects of die casting : Frommers therory, others theory ,
practical analysis and control of casting variables, correlating shot speed and pressure,
die lubrication and coolant. [No. of Hrs.: 08]

UNIT III
Gating Design, Metal melting and handling, working principles of die casting machines.
Die steel : Required characteristics of die steels, die casting alloys.
Finishing of die casting : finishing for zinc base alloys, finishing for aluminium base
alloys, finishing for magnesium base alloys. [No. of Hrs.: 08]

UNIT IV
Inspection of die castings : first inspection , final inspection. Die casting defects,
causes and its solution, estimating the cost of die castings. safety in the die casting
plant, Basic die design and die work influence factors : design criteria for die
manufacturable products, function ability aspects, control of close toleranced dimension,
elimination of secondary opeartions through better part design. [No. of Hrs.: 08]

UNIT V
Material and surface finish : Metal materials and thier properties, testing of
mechanical properties, material used for tooling application, heat treatment, surface
cleaning, surface coating. [No. of Hrs.: 08]

TEXT BOOKS :
1. Ostergaard, “Basic Die Making”, MGH Publication, 1993.
83
Effective from academic session 2008 - 09
2. Osregaard, “Advance Die Making”, MGH Publication, 1967.

REFERENECE BOOKS :
1. H.H.Doehler, “Die Casting”, Mc Graw Hill Co.,New York, 1951.
2. Street A.C., “The Die Casting Book”, Surrey Portcullis, 1986.
3. Wilson Frank W., “Die Design Handbook”, Mcgraw Hill, 1965.
4. Paquin, “Die Design Fundamentals”, Industrial Press Inc, 2005.
5. SME, “Die Design Handbook”, MGH Publication, 1990.
6. Jones, “Die Design & Die Making Practice”, Industrial Press, 1951.

84
Effective from academic session 2008 - 09
Paper Code: ETTE 404 L TC
Paper: MODERN MANUFACTURING METHODS 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Solid/Liquid Phase Metal joining and metal cutting processes : Their principle of
Operation, process parameters and application.
Newer process of Joining : Working principle and application of Laser plastic welding,
Friction stir welding, plasma welding, spray welding. [No. of Hrs.: 08]

UNIT II
Abrasive Jet Machining : Working principle, equipment used, process parameter, MRR-
variation in technique used, application.
Water Jet Machining : Working principle, equipment used, process parameter, MRR-
variation in technique used, application.
Ultrasonic Machining : Principle, applications and process parameters, purpose of slurry
selection, magnetostiction, analysis of process parameters. [No. of Hrs: 08]

UNIT III
ECM(Electro Chemical Machining) : Principle and classification of ECM, determination
and evaluation of MRR, Electrochemistry of ECM, selection of electrolytes and analysis
of ECM.
ECG( Electro Chemical Grinding) : principle and process parameters: Working
principle, equipment used, Process parameters, MRR – variation in technique used,
ECG Machine Tool Equipment, applications. [No. of Hrs: 08]

UNIT IV
Laser Beam Machining : Working principle, types of lasers, equipments, process
parameters, process characteristics.
Plasma Arc Machining : Principles and applications, Plasma Arc cutting system,
equipments.
Electron Beam Machining : Principle, beam control techniques, comparision of process
capabilities, advantages and limitations. [No. of Hrs.: 08]

UNIT V
Non-Conventional Machining Methods : Classification of non-traditional machining
methods, their comparative study.

85
Effective from academic session 2008 - 09
Electric Discharge Machining : Principle and applications, mechanism of metal removal,
basic EDM circuits, evaluation of metal removal, calculation of metal removal rate and
optimization of MRR, selection of tool material and dielectrics, flushing.
Wire Cut EDM : working principle, process parameter, equipments, characteristics of
machining process, applications. [No. of Hrs: 08]

TEXT BOOKS :
1. P.C. Pandey & H.S. Shan, “Modern Machining Process”, Tata McGraw Hills, 2006.
2. Vijay K Jain, “Advance Machining Processes”, Allied Publishers Pvt Ltd., New Delhi,
2002.
3. P K Mishra, “Nonconventional Machining”, Narosa Publication, 1997.

REFERENECE BOOKS :
1. Amitabh Gosh and A.K. Mallik, “Manufacturing Science”, Affiliated East-West Press
Pvt. Ltd., 1985.
2. Benedict. G F, “Nontraditional Manufacturing Processes”, Marcel Dekker Inc.,New
York, 1987
3. Mc Geough, “Advanced Methods of Machining”, Chapman and Hall, London, 1998.

86
Effective from academic session 2008 - 09
Paper Code: ETTE 406 L TC
Paper: MATERIAL MANAGEMENT 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction: Scope, objectives and phases in materials management,
Procurement: Purchase procedure, tender, earnest money, security deposit, purchase
order, vendor rating. Receipt: Invoice, cash memo, inspection. Storage: methods of
storage.Selective control techniques of inventory – ABC & VED analysis.
Inventory Theory: Objectives of keeping inventory, structure of inventory problems and
their analysis, relevant cost. [No. of Hrs.: 10]

UNIT II
Static inventory problems under risk : General characteristics, Christmas tree
problem, total cost matrix, opportunity cost matrix, cost of risk, mathematical formulation
of discrete and continuous cases.
Dynamic inventory problems under certainty: General characteristics, optimal lot
size models with constant demand and infinite delivery rate with and without back
ordering, quantity discounts. [No. of Hrs.: 10]

UNIT III
Dynamic inventory problems under risk: General characteristics, basic kinds of
inventory control systems – demand probability distribution – approximate methods to
find optimal P & Q systems of inventory, optimal selling policy with fluctuating prices.
[No. of Hrs.: 08]
UNIT IV
Material requirement planning: Master production schedule, bill of materials,
inventory stock, files, MRP process, logic and computational procedure using simple
example, lot sizing in MRP. [No. of Hrs.: 08]

TEXT BOOKS :
1. A.Deb, “Materials Management”, Academic Publishers, Calcutta, India, 1969.
2. Starr & Miller, “Inventory control – theory and practice”, Prentice Hall of India, 1962.
3. Gopalakrishnan & Sundaresen, “Material Management: An Integrated Approach”,
Prentice Hall of India, 1996.

REFERENECE BOOKS :

87
Effective from academic session 2008 - 09
1. G Monks, “Operations Management”, Mc Graw Hill, 1984.
2. Kanishka Bedi, “Production & Operations Management” , Oxford University Press,
2004.

Paper Code: ETTE 408 LTC

Paper: SAFETY ENGINEERING 314
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Safety Engineering : Safety principles and practices, Safe layout, Engineering Aspects
of safety, Machine tools/Equipment’s safety, guarding/interlocking/vibration-damping
etc. Safety during manufacturing processes like welding, grinding, machining, handling
of chemicals etc. [No. of Hrs.: 08]

UNIT II
Regular plant inspection and safety Audit, Hazard Analysis , Safety of electrical
installations and general electrical safety practices, Machine maintenance,
Lubrication/oiling, Safety during material handling in shops. [No. of Hrs.: 11]

UNIT III
Safety Management : Accidents , Accidents causes/body part affected, Accidents
classified (minor, reportable, fatal, dangerous occurrences), Accident Reporting and
statistics , Factory Act & Regulations: Salient points , Electric regulations: Salient points,
Safety Measurement and analysis of accidents, Enquiry committees and
implementation of recommendations. [No. of Hrs.: 11]

UNIT IV
Fire prevention & Protection: Fire potential areas, Fire fighting measures: equipments,
training, requirements. [No. of Hrs.: 08]

TEXT BOOKS :
1. L M Desmukh, “Industrial Safety Management” , Tata Mcgraw Hill, 2006.
2. A M Sharma, “Industrial Health & Safety Management”, Himalaya Publishing House,
2002.
3. Gloss, David S., “Introduction to Safety Engineering”, Wiley, New York, 1984.

REFERENECE BOOKS :
1. Pradeep Chaturvedi, “Management Safety Challenge Ahead”, (Safety Quality Forum,
The Institution of Engineers), Concept Publishinh Co. 2005.
2. Grimaldi and Simonds, “Safety Management”, AITBS Publishers, New Delhi, 2001
3. Ronald, Harold E., Brian, “System Safety Engineering and Management”, John Wiley,
New York, 1990.
88
Effective from academic session 2008 - 09
Paper Code: ETTE 410 L TC
Paper: FLEXIBLE MANUFACTURING SYSTEMS(FMS) & 3 1 4
COMPUTER INTEGRATED MANUFACTURING SYSTEMS( CIMS)
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions. However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Automated Assembly : Concept of automated assembly, need for automated
assembly, criteria for automated assembly process, impact of design on automated
assembly, control of automated assembly systems, transfer line, joining and fastening
in automated assembly.
Group Technology : Philosophy of group technology, establishment of family groups,
benefits of comprehensive coding systems, comparison between functional and cellular
layout, group technology and CNC manufacture, benefit of group technology.
[No. of Hrs.: 08]

UNIT II
Flexible Manufacturing Systems : Definition, origin of FMS , classifications of FMS,
examples of FMS, project structure and design of FMS, components of FMS, FMS –
processes, Material Handling in FMS – AGVs, Conveyors, Robots, Gantry ladders,
manual materials handling, computer simulation and computer control systems,
communications in FMS, installation and commissioning of FMS. [No. of Hrs.: 08]

UNIT III
Computer integrated manufacturing systems : Introduction, integrated data base
system, data collection system, material handling systems, integrating manufacturing
systems, computer related data base systems, networking.
[No. of Hrs.: 08]

UNIT IV
Automated guided vehicle : Definition, need for using AGV’s , type of AGV, guidance
of AGV, AGV system management, vehicle dispatch, AGV system monitoring, AGV and
safety and other material handling methods.
Industrial Robots : Introduction, need for a robot, categories of a robot, selection of
robot, configuration, mechanical ports of robot, servomotors, robot programming and
controller, robot vision, proximity sensors, applications, industrial safety and robots.
[No. of Hrs.: 11]
TEXT BOOKS :
1. Pandey P.C., “Modern Machining Processes”, Tata Mc Graw Hill, N Delhi, 1980.
89
Effective from academic session 2008 - 09
2. Groover, Mikell P. , “Automation, Production Systems and Computer Integrated
Manufacturing”, Prentice Hall, 2000.
3. Deb, Satya Ranjan, “Robotics Technology and Flexible Automation”, Tata Mcgraw
Hill, New Delhi, 1993.

REFERENCE BOOKS :
1. Ranky, Paul, “Design and Operation of FMS: Flexible Manufacturing Systems”, IFS
Publication, 1983.
2. Asfall, Ray C., “Robots and Manufacturing Automation”, John Willey, New York,
1992.
3. Boothroyd, Geoffray, Marcel Dekker, “Assembly Automation & Product Design”, New
York, 1992.
4. Edquist, Charles, Jacohsson, Steffan, “Flexible Automation : The Global Diffusion of
New Technology in the Engineering Industry”, Basil Black Well, Oxford, 1988.

90
Effective from academic session 2008 - 09
Paper Code: ETTE 412 L TC
Paper: ADVANCE MECHANICAL ENGINEERING DESIGN 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Introduction to Advanced Mechanical Engineering Design. Review of materials &
processes for machine elements. [No. of Hrs.: 08]

UNIT II
Case studies of mechanical ,engineering design failures. Review of static strength
failure analysis,-theories of failure including von-Mises theory based strength design.
High cycle and low cycle fatigue. Fatigue Strength Design of Mech. Equipment
Elements. Exercises of fatigue design of shafting and gears. Surface fatigue design
failures. Exercises of surface fatigue design of rolling contact bearings including linear
bearings. [No. of Hrs.: 11]

UNIT III
Stiffness based design.Design for creep. Combined creep and fatigue failure
prevention.Design to prevent buckling and instability. Tribodesign with applications
to design of sliding bearings and mechanical seals. Selection of lubrication sytems.
Design for corrossion, wear, hydrogen embrittlement, fretting fatigue and other
combined modes of mechanical failure. [No. of Hrs.: 11]

UNIT IV
Dynamically sound designs of machine elements like springs and shafts. Introduction to
dynamic design of mech. equipment and its implementation. [No. of Hrs.: 08]

TEXT BOOKS :
1. Hall, Allen S., “Theory and Problem of Machine Design”, Mcgraw Hill, 1968.
2. Hartmen, Maleev, “ Mechanical Design of Machines”, CBS , Delhi, 1986.
3. Tobias, Koenigsberger, “Advance in Machine Tool Design and Research”, Pergamon
Press, 1970.

REFERENCE BOOKS :
1. Jack A. Collins, “ Failure of Materials in Mechanical Design: Analysis, Prediction,
Prevention”, Wiley , 1993.
2. J Solin, G Marguis, A. Siljander, S Sipila, “Fatigue Design”, Wiley, 1993.
91
Effective from academic session 2008 - 09
3. Arthur J.Mcevily, “Metal Failure: Mechanism, Analysis, Prevetion”, Wiley, 2001.

Paper Code: ETME 416 L TC

Paper: FINANCIAL MANAGEMENT 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Aims and objectives of Financial Management Financial Analysis and Planning,
Valuation of Securities, Cost-volume, profit Analysis, Operating and Financial Leverage.
[No. of Hrs.: 08]

UNIT II
Investment and capital Structure Decision, Methods of Capital Budgeting Cost of
Different sources of Raising capital Weighted Average cost of capital, Optimum Capital
Structure, Inventory, Accounts payable, Effect of Inflation on working capital
Management, Instruments of Long-Term Finance, Internal financing and Dividend
Policy. [No. of Hrs.: 12]

UNIT III
Finance Function as Business; Approach to Financial Planning; Analysis of financial
statements; Limitations of Financial statements; Rational Analysis; Flow of Funds
Analysis; Sources of Long and Short Term Finance; Management of Components of
Current Assets-Inventory Management; Accounts Receivable; cash; bills payable,
Financial policies like working capital policy, Credit policy, Cash policy, Determinants;
Basic Features of Indian Money and Capital markets; Financial Structure of Indian
Companies and Liberalization & Globalization policy. [No. of Hrs.: 12]

UNIT IV
Applications and Case Studies. [No. of Hrs.: 09]

TEXT BOOKS :
1. Khan & Jain, “Financial Management”, Tata McGraw Hall, 2008.
2. I.M. Pandey, “Financial Management”, Vikas Publishing House, 2003.

REFERENECE BOOKS :
1. R.P. Rastogi, “Financial Management”, Galgotia Publications, 2002.

92
Effective from academic session 2008 - 09
Paper Code: ETME 418 L TC
Paper: RELIABILITY & MAINTENANCE MANAGEMENT 3 1 4
INSTRUCTIONS TO PAPER SETTERS: MAXIMUM MARKS: 75
1. Question No. 1 should be compulsory and cover the entire syllabus. This question should have objective or short
answer type questions. It should be of 25 marks.
2. Apart from question no. 1, rest of the paper shall consist of four units as per the syllabus. Every unit should have
two questions.However, student may be asked to attempt only 1 question from each unit. Each question should be of
12.5 marks.

UNIT I
Fundamentals Of Reliability & Maintenance: Reliability, Reliability Improvement,
Redundancy, Element Redundancy. Unit Redundancy, Standby Redundancy, Reliability
cost – trade off. Maintenance, Scope of Responsibilities, Types of maintenance,
Maintenance planning & control, Maintainability & Availability , Failure modes and the
Bath Tub Curve. [No. of Hrs.: 11]

UNIT II
Failure Data Analysis, Hazard Models & System Reliability: Failure Data, Mean Failure
rate, Mean time to failure (MTTF), Mean time between failures (MTBF), GraPrentice
Hall Indiacal plots, MTTF in terms of failure density, Reliability in terms of hazard rate
and failure density. Constant Hazard model, Linearly Increasing Hazard and the Weibull
Model. Instantaneous repair system, Mean time to repair (MTTR), Reliability and
Availability function. Series configuration, Parallel configuration, Mixed configuration, A r
– out – of – n – structure, mean time to failure of system, Fault tree construction,
Calculation of reliability from Fault tree.
[No. of Hrs.: 11]
UNIT III
Systematic Maintenance: Codification & Cataloguing, History cards, Instruction manual
and operating manuals, Job planning, Job manuals & Job scheduling, Job cards and
Job procedures, Maintenance organization, Centralized & Decentralized organization,
Captive maintenance, Replacement models, Spare part management.
[No. of Hrs.:
11]

UNIT IV
Condition Monitoring Techniques & Modern Concepts: Leakage monitoring, Lubricant
monitoring techniques, Ferrography, Spectroscopy, Cracks monitoring, Thickness
monitoring,
corrosion monitoring, Thermography. Terrotechnology, Failure mode effect analysis,
Failure mode effect & critically analysis, Total productive maintenance, Computer
managed maintenance system, Case studies. [No. of Hrs.: 11]

TEXT BOOKS :
93
Effective from academic session 2008 - 09
1. L.S.Srinath, “Reliability Engineering”, Affiliated East-West Press Ltd., 1985
2. S.K. Srivastava, “Industrial Maintenance Management”, S. Chand & Co. Ltd., 1998.

REFERENECE BOOKS :
1. E. Balaguruswamy, “Reliability Engineering”, Tata McGraw Hill Publishing Co., 1984.
2. Charles E. Ebling, “Reliability & Maintainability Engg.”, Tata McGraw Hill Publishing
Co., 1997.

Paper Code: ETTE 452 T C

Paper: Project Part – II 16 8
(Project Work Tool Design & Manufacturing)

The objectives of the course ‘Major Project’ are

 To provide students with a comprehensive experience for applying the knowledge

gained so far by studying various courses.

 To develop an inquiring aptitude and build confidence among students by working

on solutions of small industrial problems.

 To give students an opportunity to do something creative and to assimilate real life

work situation in institution.

 To adapt students for latest developments and to handle independently new

situations.

 To develop good expressions power and presentation abilities in students.

The focus of the Major Project is on preparing a working system or some design or
understanding of a complex system using system analysis tools and submit it the same
in the form of a write-up i.e. detail project report. The student should select some real
life problems for their project and maintain proper documentation of different stages of
project such as need analysis, market analysis, concept evaluation, requirement
specification, objectives, work plan, analysis, design, implementation and test plan.
Each student is required to prepare a project report and present the same at the final
examination with a demonstration of the working system (if any).

The faculty and student should work according to following schedule:

i) Each student undertakes substantial and individual project in an approved area of the
subject and supervised by a member of staff.
ii) The student must submit outline and action plan for the project execution (time
schedule) and the same be approved by the concerned faculty.
iii) At all the steps of the project, students must submit a written report of the same.

The documentation and presentation should be conducted before the panel of

examiners (one external and one internal) during Term End Examination. The
94
Effective from academic session 2008 - 09
Evaluation shall be done for Project Report, Presentation & Viva-voce by the panel of
examiners, and marks awarded by a committee comprising of an internal examiner, who
will ordinarily be the supervisor, and one external examiner. The internal examiner shall
award marks out of 40 % and the external examiner out of 60 %.

The project report should be prepared on the following guidelines.

Content for the Project Work
1. Cover Page
2. Title Page
3. Certificate
4. Acknowledgment
5. Index / Content Page No
6. Introduction (Aims & Objectives, History, Primary Data, Explanation of Terms)
7. Research Methodology (Methods adopted for collecting Data)
Questionnaire , Interview, Mails etc.
8. Data Analysis & Data Interpretation (Data is depicted with the help of Bar
Chart, pie Chart, Graphs, Statistical formulae and interpreted)
9. Conclusions and Limitations
10. Suggestions / Amendments
11. Annexure
12. Bibliography (List of Reference Books)
13. Questionnaire (Blank Format)

95
Effective from academic session 2008 - 09