®

DELUXE STITCHER
C O M P A N Y I N C .
solving your wire stitching needs for 125 years...

Head Serial Number :

Date Purchased :
Where Installed:
(make/model of machine)

G8 Stitcher Head
OPERATION AND MAINTENANCE MANUAL

Wire Sizes: 23-28 Ga. Round, 20x24 and 21x25 Flat

Crown Size: 1/2” (13.5 mm)
Capacity: 2 sheets to 5/16” (8 mm) Standard
2 sheets to 5/32” (4 mm) Loop

Before using this Stitcher Head, all operators must study this manual and follow the
safety warnings and instructions. Keep these instructions with the G8 Stitcher Head
for future reference. If you have any questions, contact your local DeLuxe Stitcher
Company Graphic Arts Representative or Distributor.
2
3
 WARNING!

G8 Stitcher Head
Machine operators and others in the work area should always wear
safety glasses to prevent serious eye injury from
fasteners and flying debris when loading, operating,
or unloading this machine.

Do not operate this stitcher head without all stitcher machine

guards in place. Do not modify the guards in any way.
Always disconnect the power supply before removing
any guards for servicing.

Never operate the machine with wire feeding through

the head unless there is stock above the clinchers,
otherwise serious damage may result.

Always turn power off when making adjustments. Always

disconnect the power cord before any disassembly work.

EYEWEAR

REQUIRED
4
Table of Contents

Safety Warning .................................................................................5

Introduction .........................................................................................................7
Part Number Definition.....................................................................................7
Specifications......................................................................................................9
Installation .......................................................................................................11
Pre-Inspection.................................................................................11
Inspection.......................................................................................11
Assembly Parts ..............................................................................12
Mounting ..................................................................................... 13-14

Operation ........................................................................................................15
Wire Threading ........................................................................... 15-16
Wire Straightening ...................................................................... 17-18
Adjustments and Settings ........................................................... 19-24

Maintenance.......................................................................................................25
Lubrication .................................................................................. 25-26
Cleaning .........................................................................................27
How to Order Spare Parts..............................................................28

Troubleshooting.................................................................................................29
Formed Staple Chart................................................................... 30-31

Appendices .......................................................................................................32
Exploded Drawings with Part Number/Description/
Cross Reference/Qty................................................................... 32-50

Optional Equipment........................................................................51-52
Parts Index......................................................................................................53-55
Warranty..............................................................................................................56
Registration Card........................................................................................... 57-58
Common Replacement Parts........................................................................58

5
Introduction
Typical Style Uses:
G8BHD.............................................................. No. 2 and M2 Wire Stitchers
G8MHD........................................................... No. 17 and M17 Wire Stitchers
G8HD..................................................................Automatic Saddle-Stitchers,
................................................................. Gang-Stitchers, Multibinders and Others

Examples of Replacement Heads for OEM Users*:

AM Graphics / Harris / Heidelberg / Sheridan 455, 562, 690............. G8HD24A

AM Graphics / Harris / Heidelberg / Sheridan 705............................. G8HD24A
C.P. Bourg ................................................................................................ G8HD24D
Christensen............................................................................................... G8HD24A
Horizon SP, SPF....................................................................................... G8HD24D
Macey Multibinder ................................................................................. G8HD24B
McCain ..................................................................................................... G8HD24A
Rosback .................................................................................................... G8HD24B
Boewe 4601............................................................................................... G8BOHD241/2
McCain / OmegaBinder.......................................................................... G8HD23A
Harris 855................................................................................................. G8HD24-HARRIS
McCain / Sheridan / Harris / Bielomatik, ECH Will \ et.al................. G8HDC24A
Heidelberg ST100, ST270, ST300, ST350.............................................. G8HEHD241/2
JMZ&A (Parker)..................................................................................... G8PKHD241/2
Watkiss ..................................................................................................... G8WAHD241/2

* These are just a few examples of the replacement heads available for these OEM’s.

Part Number Definition

The part number for each Stitcher Head can be used to define the stitcher head itself, in most
cases. The Head’s model type, mounting style, nominal wire size and crown size can all be
determined from the part number.

G8 P HD 24 A 1/2

1/2 = Crown size in inches

A = Mount and Wire Guide Spring Type
24 = Wire Size
HD = Head
P = Original Equipment Manufacturer
G8 = Model type

6
 Some Head Style Examples

A9086A A9086A

A9086A 9193A 9193A

Figure 1 - Style Comparisons

7
Specifications

Weight
Shipping Weight . . . . . . . . . . . . . . . 13 lbs (5.9 kg)
Box Size . . . . . . . . . . . . . . . . . . . . 21 x 10 x 6

Physical Dimensions
Height . . . . . . . . . . . . . . . . . . . . 13-9/16­” (345 mm)
Width . . . . . . . . . . . . . . . . . . . . 2-3/4” (70 mm)

Stitching Capacity . . . . . . . . . . . . . . . . . . . Two Sheets to 5/16” (8 mm)

. . . . . . . . . . . . . . . . . . . . Two Sheets to 13/64” (5 mm) Loop
(Stitching capacities are highly dependent on wire and paper type, tensile strength and machine capacity.)

Wire Types
. . . . . . . . . . . . . . . . . . . . 23 through 28 round or
. . . . . . . . . . . . . . . . . . . . 20x24,20x25 and 21x25 flat
. . . . . . . . . . . . . . . . . . . . (24 gauge round standard)
. . . . . . . . . . . . . . . . . . . . 25 gauge only for Loop

Crown Sizes
. . . . . . . . . . . . . . . . . . . . 1/2” (13mm)
. . . . . . . . . . . . . . . . . . . . 13/64” (5mm) Loop

Minimum Head Centers

. . . . . . . . . . . . . . . . . . . . 2-3/64” (52mm) at two sheets to
. . . . . . . . . . . . . . . . . . . . 1/16” (1.5mm) material thickness
. . . . . . . . . . . . . . . . . . . . loop = 56mm at two sheets to 2mm

Stitches Per Hour . . . . . . . . . . . . . . . . . . . . 20,000 or 12,000 with Loop Head

Replacement for: . . . . . . . . . . . . . . . . . . . . Interlake/Acme/Champion/

. . . . . . . . . . . . . . . . . . . . Magnatek/M2000 heads,
. . . . . . . . . . . . . . . . . . . . 26/26D Model Heads, or Hohner
. . . . . . . . . . . . . . . . . . . . 52/8, 55/7, 43/6 and 48/5 Heads
. . . . . . . . . . . . . . . . . . . . and others

Make sure all guards are in place before 

! WARNING
operating the stitcher head

8
Dimensions

2.256 [57.30]
5/32 [3.9]

CENTER OF
1 3/16 [30.3] STITCH

3/8 [9.5]

DETAIL A
SCALE 1.5 : 1

4 1/2 [114]
27 5/8 [702]

25 11/16 [653]
1 1/2 [38.5]
21 1/32 [611]

1 1/32 [26]
2 3/64 [52]
5/16 [8]
THICKNESS
ADJUSTMENT

5/16 [8]
THICKNESS
ADJUSTMENT 13 9/16 [345]
MAX.

2 [50.8] .248 [6.3]

DRIVE STROKE
2 7/16 [62]

5 21/64 [135.3]
4 23/64 [110.7]

2 3/32 [53.3]
2 13/16 [71.5]

4 25/32 [121.4] 2 3/4" [70]2

1/4" [57]
3 9/64 [80]

1 3/8 [34.9]

Figure 1

9
 Installation

Pre-Inspection

Carefully inspect the condition of the shipping container before unpacking your G8 Stitcher Head.
If the container is broken or damaged and there is evidence that the stitcher head may be damaged,
immediately notify the carrier who delivered the head and the DeLuxe Stitcher Graphic Arts
Representative from whom the G8 Stitcher Head was purchased.

Inspection

As you carefully unpack the head, check to make sure all components were delivered and are in
good working order. Refer to Figure 2 in this manual for reference to the following pieces:

• G8 Manual
• 2.0mm Hex Key Wrench (G20374)
• 2.5mm Hex Key Wrench (G20361)
• 3.0mm Hex Key Wrench (G20360)
• 5.0mm Hex Key Wrench (G20362)
• 7.0mm Open End Wrench (G20364)
• Complete Wire Guide Spring Plate Assembly (G20278AA)
• Adjustment Knob Assembly (G20228A)
• Short (G20279A) or Long (G20286A) Wire Guide Spring Assembly
• Clincher Plate Assembly - Thick (9086A)
• Round (CA9083A) or Flat (9083C) Thick Clincher Points
• Clamp Block (9002) and Clamp Block Eccentric (G20124) or Rear Clamp Pin (G20366)
and Rear Mounting Bolt (G20367 or G20341)
• Either Clincher Plate Binder Nut (2091), Bolt (9088) and Thick Clincher Slide (CA9093A)
or Clincher Plate Binder Nut (2091), Bolt (9088), Adjustable Clincher Slide (9084B),
Clincher Slide Adjusting Screw (9087) and Clincher Slide Adjusting Lock Screw
(UA4808.7).
• Stitch Samples

* Note: the accessories included with the G8 will vary with the style of Head purchased

10
 Assembly Parts

Please take a few moments to fill out the registration card located on page 44 prior to beginning
installation.

G20279A
G20679A

G20380
5mm T-Handle Hex Key
OPTIONAL

G20286A

G20362
5mm Hex Key

G20279AA
G50286SA
(Spring not shown
here, see pg. 44)

G20360
3mm Hex Key
G20181 or G50716
G20181B 9002 OPTIONAL
G20101
OPTIONAL

G20361
2.5mm Hex Key

G20124
G20374
2mm Hex Key G20103

G20366 HN1213
(1/2” thread)
or G20170
(8mm thread)
G20364 OPTIONAL
7mm Wrench
G20228A
G20341
(1/2” thread)
CA9083A or G20367
OR 9083C (8mm thread)
OPTIONAL

CTTT9086A
9193A (See page 42 for
more detail on
full Clincher Plate
Assemblies.)
Figure 2 - Assembly Parts

11
Mounting

Figure 4 - Alternate Mount Methods

Upper Cutter Block
Adjustment Bar
G20245
G20251

Figure 3 - Attaching the Wire Guide

Figure 5 - Attaching & Removing the Clincher Plate

12
 LINE UP GROOVES

Figure 5 - Attaching & removing Stitcher Heads

13
 Operation

Wire Threading (Figures 7 - 13)

1. Slide the Wire Holder Retaining Spring over to the side
Figure 7 - Threading the Head
and remove the Wire Holder (Figure 7) from the Stitcher
Wire Holder
Retaining
Head.
Spring
G20183
2. Pass the wire from the Spool over the Wire Guide Spring
Wire Holder between the Wire Guides, between the Washer and Wire
G20559BA Oiler Felt and into the Anti-Backup Wire Unit (Figure 8).
or G20301A

3. Turn the Feed Release Handle clockwise (Figure 9)

to disengage the Feed Gears and guide the wire into the

Feed Release Lever

(Turn to disengage
position as shown.)

Wire Guide Spring Feed Gears

G20279,
G20286A or
G20679A

Wire Oil Felt

Middel Wire Tube
G20293

Anti-Backup Wire Unit

G50800CA

Figure 9 - Threading the Head

Middle Wire Tube (Figure 10). (Or with the gears engaged,
place the Adjustment Handle over the Small Gear pin and
rotate clockwise to feed the wire through. See Figure 11.)
Figure 8 - Threading Re-engage the gears.
the Wire Spring
4. Turn the stitcher machine on and cycle it until the wire
emerges from the Lower Wire Tube in the Cutter Block. When accomplished, proceed to wire straightening

Note: Never operate the Stitcher Head with the Wire Holder in place unless there is wire stock above
the Clincher Points.

14
Figure 10 - Threading the Head
Small Feed Gear
G20112

Large Feed Gear

G20110A

Wire

Middle Wire Tube

G20144A

Figure 11 - Threading the Head

Feed Release Lever

G20119
(Turn to engage
position as shown)

Adjustment Handle
G20228A

Lower Wire Tube

G20199A

Cutter Block
G20197A

Wire Guides
G20541

Wire Straightener
Eccentric
G20206
Figure 13
Cut-out View of
Figure 12 - Threading the Head Wire Threading

15
 Adjusting Wire Straightness (Fig. 14-17)

Figure 16a - Wire Curls Up

Set Screw
G20273

Hex Nut
G20226

Wire
Straightener
Eccentric
G20206
RAISE WIRE

LOWER WIRE

Figure 15 - Adjusting Wire Straightness

Figure 16b - Wire Curls Down

Horizontal Adjustment (Figures 15-16)

Observe the direction the wire is moving as it emerges. Use a

slotted head screwdriver on the Wire Straightener Eccentric in the
Cutter Block to adjust the wire. If the wire is curved upwards, turn
the Wire Straightener Eccentric clockwise. If the wire is feeding
downward, turn the Eccentric counter-clockwise.

Figure 16c - Straight Wire

16
 Front-to-Back Adjustment Screw
G20215
(1 per side)
If the Wire Guide Bars are not properly positioned, the wire will
rub against them as it exits the Cutter Block. Look at the G8 Head
from the side past both the Right and Left Wire Guide Bars (Figure
17). Make sure there is a clear view of the opening in the Fixed
Wire Cutter from the side of the G8 Head. If there is not, loosen
the Flat Head Machine Screws securing the Wire Guide Bars to the
Pivot Block and move them out of the path of the wire. Tighten the
Screws after making sure the Wire Guide Bars are even with each Fixed Wire
other. Replace the Wire Holder and re-engage the Wire Holder Cutter
Retaining Spring. G20200

NOTE: Depending on its size, adjust wire straightness every

3-10 lbs. of wire used approximately as follows:

5-10 lbs. Spool every 3 lbs.

10-25 lbs. Spool every 5 lbs.
25-70 lbs. Spool every 7 lbs.
70 lbs.+ Spool every 10 lbs. Figure 17 - Wire Guide Alignment

Aligning the Wire Holder (Figure 18a & b)

Figure 18a - Wire Holder Alignment In order to form a quality stitch, the
Wire Holder has to be in alignment
with the Bender Bar. Specifically,
the cut piece of wire held in the Wire
ALIGN TO
Wire Holder Holder has to line up with the grooves
Adjustment Screw
BENDER
G20665
in the Bender Bar. Poor adjustment
BAR
GROOVE
Figure 18b - Wire Holder Alignment

WIRE
BETWEEN
WIRE IN BENDER
WIRE INSERT
HOLDER GROOVES

17
may cause broken crowns or other poor stitching.

Load a piece of wire into the Wire Holder. Using a mirror, check to make sure the wire in the Wire
Holder is lined up with the grooves in the Bender Bar (Figure 18b). If it is not, loosen the Socket Head
Set Screw in the front of the Wire Holder and the Hex Nut (seen in Figure 15) securing the Wire Holder
Adjustment Screw (Figure 18a). Turn the Adjustment Screw until the wire is aligned with the grooves in
the Bender Bar. Tighten the Hex Nut and Set Screw to secure this setting.

Remove the wire in the Wire Holder and load another piece in the Stitcher Head. Verify that the setting
established is accurate by again checking the piece of wire with the mirror.

Adjusting the Stitch (Figure 19-23)

Figure A
MORE WIRE DRAW
Adjust Length

LESS WIRE DRAW

Feed Rack RIGHT LEG TOO SHORT

Adjustment Knob
G20173

RIGHT LEG TOO LONG

Before making any adjustments, make sure

your stitching machine compression setting
Figure 19 - Adjusting the Wire Draw is set to the proper thickness of work. Make
a few sample stitches and look at the results.
Setting the Stitch Gap (Or Adjusting the Wire Draw)

To adjust the overall length (wire draw) of the stitch, disengage the Small Feed Gear by turning the Feed
Release Handle 1/4 of a turn to the right as shown. Adjust the Feed Rack Adjustment Knob until the gap
between the staple legs allows only the edge of a fingernail to pass between them.

• To extend the length of the stitch or decrease the gap, turn the Feed Rack Adjustment Knob clockwise.
(See upper view of Figure A)
• To shorten the length of the stitch or increase the gap, turn the knob counter-clockwise. (See lower view
of Figure A)

Centering the Stitch Gap (Or Setting Equal Length Legs)

The amount of wire on either side of the stitch gap should be the same. The gap position is controlled by
the position of the Cutter Block. As thicker work is stitched, the Cutter Block must be moved further from
the Wire Holder to keep the legs of the stitch even and the gap centered.

18
Upper Cutter Block Cutter Block For G8 Heads mounted to a machine
Adjustment Bar Adjustment with an adjuster rail, loosen the two (2) Hex
G20245 or Rack
G20251 G20143
Head Screws securing the Lower Cutter Block
Adjustment Bar and Cutter Block Adjustment
Connector to the Upper Cutter Block Adjustment
Bar (both versions shown in Fig. 4). For all G8
Hex Head style Heads, place the Adjustment Knob over
Screw
G20289 the Cutter Adjustment Stud as shown in Figure
20 and engage the teeth of the Cutter Block
Cutter Block
Adjustment Rack and adjust as shown in the
Adjustment following illustrations. Be sure to run a couple
Connector of stitches after each adjustment.
G20246

Lower
Cutter Block
Adjustment
Adjustment
Knob

! WARNING
Bar G20228A
G20242
Always disconnect the power supply
before making any adjustments or
Cutter Box
servicing the head.
Figure 20 - Adjusting the Stitch G20197BAA

Figure 21 - Adjusting the Stitch Figure 22 - Adjusting the Stitch

1/16"[1.6mm] 1/16"[1.6mm]
TOO FAR RIGHT OF TOO FAR LEFT OF
CENTER OF STITCH CENTER OF STITCH
WIRE LENGTH WIRE LENGTH

Gap of stitch is Gap of stitch is 1/16"

Figure B 1/16" off center to Figure C off center to the left.
Adjust Left the right. To correct. Adjust Right To correct. turn the
turn the Adjustment Adjustment Knob
Knob clockwise. to counter-clockwise
shift the Cutter Box to shift the Cutter
1/16" to the left. 1/16" to the right.

19
 Figure 23 - Adjusting the Stitch

Figure D
Correct Stitch

The ideal stitch has the center of gap

CORRECT SETTING.
aligned to the center of the finished stitch.
CENTER LINE OF BOTH STITCH
& DRIVER ARE ALIGHED

Aligning the Clincher Plate (Figures 24-27)

In order to produce properly clinched staples, the center of the Clincher Plate (round or flat, thick or
thin) must be exactly in line with the Driver both left-to-right and front-to-back.

Front-to-Back Adjustment
Manually activate the G8 until the Stitcher Head is at the bottom of its stroke and the Driver is touch-
ing the top of the Clincher Plate. Looking from
the side of the Stitcher Head, make sure the rib
of the Driver is aligned with the center of the gap
between the front and back plates of the Clincher UPPER
ADJUSTMENT SET
Plate Assembly. All adjustments are made to the SCREW
screws in the back of the G8 while the Stitcher
Head is removed from the Stitcher Machine.

Loosen the two (2) Socket Head Set Screws in

the side of the Head. If the Driver is positioned
in front of the Clincher Plate then the upper
Adjustment Set Screw must be turned counter-
clockwise until the Screw sticks out slightly from
the back of the Head, while the lower Screw
remains under flush. Set Screw Set Screw
G20191 G20229
If the Driver is positioned in back of the Clincher
Plate then the lower Adjustment Set Screw must LOWER
be turned counter-clockwise until it sticks out ADJUSTMENT SET
SCREW
slightly from the back of the Head, while the
upper Screw remains under flush.

20
 DRIVER TOO FAR DRIVER TOO FAR
FORWARD, ADJUST BACK, ADJUST
CENTERED STITCH UPPER SET SCREW LOWER SET SCREW

Figure 25 - Properly Aligned Figure 26 - Front To Back Alignment

Slight adjustments to the Set Screws make significant differences in position. Once the position is set,
tighten the two (2) Socket Head Set Screws in the side of the Stitcher Head.

Left-to-Right
Looking from the front of the Stitcher Head, make sure the Driver is centered directly above the Clincher
Slide (CA9093A or 9084B). If it is not, loosen the two (2) Clincher Plate Nuts and move the entire
Clincher Plate Assembly to the right or to the left. Secure this position while tightening the nuts again.

Figure 27 - Left to Right Alignment

CLINCHER POINTS
TO BE FLUSH OR
JUST ABOVE PLATE

Clincher
Plate Nuts
2091
LOOSEN, ADJUST CORRECT
& RETIGHTEN ALIGNMENT

Adjusting the Clincher Points (Figure 28-29)

The position of the Clincher Points should be flush, or slightly above flush, with the Clincher Plate in
order to achieve a quality stitch. To ensure this, manually turn the stitcher machine until the Driver is at
the lowest position of its stroke and the Clincher Points are at their highest position. Turn the stitcher
machine just past this point to reveal the Clincher Points’ position. Clincher Points that do not pivot high
enough will produce a weak clinch, where Clincher Points that pivot too high will cause poor stitch quality
or cut the stock being stitched.

21
 Note: Ensure that the stitcher machine's compres-
sion setting is correct before making Clincher
Clincher Points
Point adjustments.

To adjust the Clincher Points, loosen the Set Screw

on the top of the Clincher Slide (9084B). Turn the
Clincher Slide Adjustment Screw clockwise to lower
the Clincher Points and counter-clockwise to raise
them. Once set, reighten the Set Screw.
Set Screw
UA4804.7
Refer to the complete list of wear parts for the G8 style
Clincher Slide Stitcher Head, found in the back of this manual on page
Adjustment 47. The Clincher Points and Clincher Plates necessary
Screw
LOWER
9087
for a quality stitch are specific to the crown size and
wire gauge size used in each stitcher head.
RAISE
For a Solid Clincher Plate, the legs of each stitch are
Figure 28 - Adjusting the Clincher Points formed when the wire hits the formed grooves of the
Clincher Plate, instead of movable Clincher Points
coming up to meet the wire. The resulting stitch will curled legs instead of flat (Figure 29).

The only adjustment that can be made to a Solid Clincher Plate is to make sure it is centered below the
Head’s Driver and even that adjustment can only be made on multi-head stitcher machines.

Solid Clincher Plate

9800B

FLAT CLINCH

SOLID CLINCH

Figure 29 - Solid Clincher Plate

Always disconnect the power supply before 

! WARNING
making any adjustments or servicing the head.

22
Adjusting the Bender Bar Stop (Figures 29-31)
The Bender Bar Stop is set at the factory. The Stop
controls the position of the Bender Bar Latch at the
top of the stitcher head’s stroke. If the Latch does not
2.5
3/32" fall within the proper area of the Driver Bar, partially
formed stitches will result or the G8 will jam.
Bender Bar
Latch
G20149 The right edge of the Bender Bar Latch should stick
out from the Bender Bar at least 3/32” [2.5mm]
(Figure 30) when the G8 reaches the top of its stroke.
If the Latch does not protrude this far then the Bender
Bar Stop Screw is set too high. If the Stop Screw is
set too low then the wire will hit the Bender Bar rather
than feeding below it for forming.

To adjust, remove the two (2) Screws securing the

Pivot Block (with attached components) to remove it
from the Feed Gear Bracket (Figure 31). Loosen, but
Figure 30 - Adjusting the Bender Bar Stop do not remove, securing the Stop Screw. Turn the Stop

G20196

G20189

Set Screw
G20273
(Hidden)
Bender Bar
Stop Screw
G20229
Pivot Block
G20139A

Figure 31 - Removing Pivot Block Assembly

23
 Screw clockwise to raise the Bender Bar’s
Figure 32 - Adjusting the Bender Bar Stop position and counter-clockwise to lower it’s
position. The normal position is about 1/8”
or 3mm out from the Feed Gear Bracket.

Replace the Pivot Block using its Locating

Pins with the holes in the Bonnet. Manually
3 LOOSEN SET SCREW,
1/8" ADJUST STOP SCREW, turn the Large Feed Gear (G20110A) if its
TIGHTEN SET SCREW teeth are not aligned with those on the Feed
Rack (G20127). Replace the Screws.
LOWER
BENDER BAR
RAISE
POSITION
BENDER BAR
POSITION

Maintenance

Lubrication (Figure 33)

Use any standard S.A.E. #10 oil for lubricating the heads. Heads that are in constant operation should
be lubricated daily. Heads that are operated periodically should be lubricated every five pound wire spool
change or every month, which ever comes first. Usually, only a drop of oil is required at each lubrication
point. Care must be taken that those parts of the head that contact the work to be stitched are free of oil.
Lubricate regularly instead of excessively. Excessive oiling will result in work becoming spotted with oil.
Use one drop of oil in the following lubrication points:

1. The top of the Bonnet (G20000A) on either side of the Feed Slide (G20131).

2. The fittings on the Feed Lever Pivot Pin and the Small Feed Gear Pin (G20262A).

3. The Cutter Operating Lever Pivot Pin (G20231) and Roller Pin (G20232).

4. The Wire Straightening Rollers (G20208B) in the Cutter Block Assembly (G20197A).

5. On the Wire Holder Assembly under the Wire Holder Retaining Spring Foot (G20184).

6. Where the Wire Holder Assembly (G20559BA) pivots in the Left and Right Wire Guide Bars
(G20141 and G20142).

7. On the Bender Bar Latch (G20149) and the Latch Release Cam (G20115).

8. In the Cutter Block Assembly, along side the Cutter Operating Slide (G20198).

9. In the Wire Felt to saturate it.

24
 9

8 6

5
7

Figure 33 - Lubrication Points

25
 Always power down the stitcher machine 
!! CAUTION
Cleaning before any maintenance or adjustments
are made to the stitcher head.

In addition to proper lubrication, routine cleaning is important for the maintenance of your G8 Head.
The entire Head should be torn down and rebuilt every three to six months and the following areas
should be cleaned once every three months:
• Large Feed Gear (G20110A): remove and wash in an oil-dissolving
solvent, like Aeroshell 14 (G20824). Dry and relubricate.

• Anywhere that dust, oil or pieces of wire and paper have built
up - for example: around the Clincher Points and around the
Wire Straightener Rollers.
Figure 34 - Large Feed Gear

26
 Ordering Spare Parts

In time, you will need to replace some parts in your G8 style Stitcher Head. When this happens,
first locate the needed part in one of the following diagrams. Then locate the DeLuxe Stitcher part
number and contact your Graphic Arts Representative to order the part by the part number,
description and quantity. Customer Service Hotline: 800-634-0810
solving your wire stitching needs for 125 years...

27
 Troubleshooting (Figure 35)

The quality and quantity of work that can be produced with the G8 Stitcher Head is
dependent upon the operator making all adjustments as accurately as possible and carefully
maintaining the head. The cause of staple imperfections usually can be traced to inaccurate settings
or normal wear of moving parts. In the event of trouble of this nature occurring, the operator can,
by referring to the following troubleshooting chart, quickly locate and remedy the cause or causes
of the trouble.

The following is a brief list of problems and solutions which should cover the majority of situations
encountered when stitching with the G8 Stitching Head. In the event of problems of this nature
occurring, the operator can, by referring to the following troubleshooting chart, quickly locate
the solutions.

28
 problem: Crown Not Straight
solution: Straighten the wire. (See page 17) Align the Clincher
Points. (See page 22) Reverse or replace the worn or broken
Driver. (See page 28) Make sure the Cutters are aligned and not
dull. (See page 18) Check for correct wire size and strength being
used. Check for correct work thickness setting. Check the quality of
the wire being used, change spools.

problem: Leg(s) Buckled

solution: If the ends of an unformed piece of wire are not smooth,
the Wire Cutters are worn. Check for wear and rotate or replace if
needed. (See page 28) Make sure the Cutters are aligned properly.
(See page 18) Make sure the correct wire size is being used and that
the wire is straight. (See page 17). Check the quality of the wire
being used, change spools.

problem: Corner Buckled

solution: Check the Driver for a chipped corner and rotate or
replace it if needed. (See page 28) Align the Wire Holder. (See
page 18) Check the tensile strength of the wire or use thicker wire.

problem: Clinch Too Loose

solution: The Clincher Points are too low or too high and need
adjusting. (See page 22) The compression of the stitcher machine
is insufficient and needs to be increased.

problem: Left Leg Too Short / Right Leg Too Long

solution: Adjust the position of the Cutter Block Assembly by
moving it away from the Head. (See page 20)

problem: Left Leg Too Long / Right Leg Too Short

solution: Adjust the position of the Cutter Block Assembly by
moving it away toward the Head. (See page 20)

Figure 35 - Troubleshooting

29
 problem: Staple Legs Too Long or Too Short
solution: Correct the overall wire draw by repositioning the Feed Rack
within the G8 Head. (See Page 21)

problem: Left Leg Missing

solution: Straighten the wire. (See page 17) The Wire Holder Assembly
is not aligned properly with the groove in the Bender Bar.

problem: Legs are Spread or Contracted

solution: Straighten the wire. (See page 17) Weak wire or wrong gauge
being used, change spools.

problem: Legs Stray Forward or Backward Consistently

solution: The Clincher Points are not aligned properly front to back.
(See page 22)

problem: Stitch Stray Randomly In and Out and Front to Back

solution: Straighten the wire. (See page 17) Make sure the Cutters are
aligned properly. (See page 18) Check the tensile strength of the wire or
use thicker wire. Verify correct wire gauge is being used, change spools.

problem: Partially Formed Stitches

solution: The Bender Bar Latch is not engaging with the Driver Bar,
either may be worn. The Bender Bar Stop Screw is set too low. (See page
24). Broken Latch or Latch Spring, replace. (See page 28)

problem: Weak crown, crown breaks off after stitch

solution: Align the Wire Holder with the grooves in the Bender Bar
(See page 18). Check the tensile strength and size of the wire being used.

problem: No wire being drawn

solution: Make sure the Feed Release Handle is turned to the “on”
position and the Feed Gears engaged. (See page 16)

Figure 35 - Troubleshooting

30
 Bonnet Sub-Assembly
G50716 G50394 (4) BOLT MOUNT
HEADS

G20367 (Panduro type collators)

[8MM THREAD] M8 (HORIZON TYPE COLLATORS), CP BOURG

G20170
[OPTIONAL METRIC]

HN1213 G20341
G20273 (2) G20122A (2)
[1/2-13 THREAD]
(M2 DELUXE)

G20366 G20120 (2)

CLAMP MOUNT
HEADS
9002
G20229 (2)
G20191 (2)

FRONT MOUNT
HEADS

G20115
G20190 (2)

G20102 (2)

G20101

G20124

G20264 (2)
G20103
G20275 FRONT MOUNT
HEADS

31
 Part Number / Description Cross-Reference

Bonnet Sub-Assembly
G20115 LATCH RELEASE CAM 1
G20120 FEED RELEASE BUSHING 2
G20122A FEED SLIDE RETAINING SCREW ASY 2
G20190 SCREW M3X.5X10- FHMS- SLOTTED 2
G20191 SCREW, M4X.7X8 SHSS 2
G20229 SCREW, M6X1.0X12, NYLON 2
G20264 SCREW M5X.8X5 SHCS 2
G20273 SCREW M4X0.7X4 SHSS 2
G20275 BALL SPRING PLUNGER 1

Mount Head Styles

Bolt Mount Heads

G20170 HEX JAM NUT, M8X1.25 1
G20341 REAR MOUNTING BOLT, 1/2”-13 1
G20366 REAR CLAMP PIN 1
G20367 REAR MOUNTING BOLT, 8MM 1
G50394 FLAT WASHER - M8 4
G50716 MOUNTING BLOCK HANDLE, M8 1
HN1213 BONNET STUD NUT, 1/2”-13 1

Front Mount Heads

G20101 FRONT MOUNT BLOCK - G8 1
G20102 SCREW M6X1.0X12, NYLON 2
G20103 SCREW M6X1.0X30 1

Clamp Mount Heads

9002 BONNET CLAMP BLOCK 1
G20124 BONNET CLAMP ECCENTRIC 1

32
 Bonnet Sub-Assembly
G20264
G20274 G20118
Optional
Feed Release Handle (STAHL)
ST-90 G20368
G20371 G20121

G20167 (2) G20119

G20264
G20251 G20133A
G20372

G20245

G20250 (2) G20269

G20182
G20246

G20196 (2)

G20244
G20289 (2) G20144A

G20214 (2)
G20249 (2) G20220 G20126
G20236
G20240

G20243
G20242
G50268

G20237B
G20231
G20191
G20235

G20140
G20175
Low Head G20204
G20234 (2)
(FRONT MOUNTING
HEAD IS REQUIRED.) G20230A
G20202
G20241 (3)
G20113 (2) G20233
G20175 (2) G20232

33
 Bonnet Sub-Assembly
G20118 FEED RELEASE HANDLE CAM 1 G20234 E-RING- 3/16" 2
G20119 FEED RELEASE HANDLE 1 G20235 FOLLOWER BEARING SHAFT 1
G20121 FEED RELEASE PLUNGER 1 G20236 TUBE PIVOT SCREW 1
G20126 TUBE PIVOT PLATE 1 G20237B ADJUSTMENT STUD 1
G20133A FEED RELEASE BLOCK ASSY 1 G20240 ADJUSTMENT WASHER 2
G20140 FOLLOWER BALL BEARING 1 G20242 ADJUSTMENT BAR - LOWER 1
G20144A MIDDLE WIRE TUBE ASSEMBLY 1 G20243 DOWEL PIN 1/4X9/16 1
G20167 SCREW, M4X0.7X10 FHCS 2 G20244 TUBE PIVOT CLIP 1
G20175 SCREW M4X.7X6 SHCS 2 G20245 ADJUSTMENT BAR - UPPER 1
G20182 FEED GEAR SHAFT PLATE 1 G20246 ADJUSTMENT CONNECT 1
G20191 SCREW, M4X.7X8 SHSS 1 G20249 CUTTER BLOCK WASHER 2
G20196 SCREW M3X.5X6 SHCS 2 G20250 SCREW M4X.7X14 2
G20202 CUTTER BLOCK SLIDE PLATE 1 G20251 ADJUSTMENT BAR - UPPER 1
G20204 UPPER CUTTER BLOCK GUIDE 1 G20264 SCREW M5X.8X5 SHCS 2
G20214 SCREW M4X0.7X8 FHMS 2 G20269 SPIROL PIN 3/16X5/8 1
G20220 HEX NUT M5X.8 1 G20274 HEX JAM NUT, M6X1 1
G20230A CUTTER OPERATING LEVER ASSY 1 G20289 SCREW M4X.7X16 2
G20231 CUTTER OP. LEVER PIVOT PIN 1 G20368 FEED RELEASE HANDLE CAP 1
G20232 CUTTER OP. LEVER ROLL PIN 1 G50268 FEED LEVER SPRING 1
G20233 CUTTER OP. ROLLER 1

Front Mounting Heads

G20113 SUPPORTER GUIDE PLATE 2
G20175 SCREW M4X.7X6 SHCS 1
G20241 SCREW M4X0.7X6 SHCS 3

Optional
Feed Release Handle (STAHL)
G20371 FEED RELEASE HANDLE 1
G20372 FEED RELEASE SHAFT 1
G20264 SCREW M5X.8X5 SHCS 1

34
 Feed Lever and Feed Gear Assemblies

G20262A (2)

G20268
G20132

G20263 (2)

G20112
G20267
G20181 G20181B
G20264
G20140 G20266
G20138 (2) G20137 G20136BA
(BEARINGS) (BEARING)
G20110A

G20129 G20189 (4)

G20111A

G20128
G20195 (2)
G20195

G20261B
G20187
G20114
G50394
G20186
G20273
G50617
G20139A
INCLUDES
G20139 G20273 G20196

072001 G20139B

G20143 G20196 (2) G20298

G20214
G20196
G20541B
G20229
G20256
G20139BAA G20241 (2) G20183
G20541 G20256B
G20229 G20184 G20175
G50617
G20579 (2)
G20298
G20183
OLD STYLE PIVOT BLOCK
DESIGN
G20180
G8KL
35 G20316 LOOP CONFIGURATION
 Feed Gear Assembly
72001 SCREW M4X0.7X8 1
G20110A LARGE FEED GEAR ASSEMBLY 1
G20111A FEED PINION ASSEMBLY 1
G20114 FEED PINION SHAFT 1
G20128 LARGE FEED GEAR WASHER 1
G20129 SMALL FEED GEAR WASHER 1
G20136BA FEED GEAR BRACKET ASSEMBLY 1
G20137 ROLLER CLUTCH BEARING 1
G20138 FEED PINION BEARING 2
G20139BAA PIVOT BLOCK ASSEMBLY COMPLETE - G8 1
G20175 SCREW M4X0.7X6 SHCS 1
G20180 FLAT WASHER M6 1
G20181 UPPER WIRE TUBE 1
G20181B UPPER WIRE TUBE, G8 STITCHEMASTER 1
G20183 WIRE HOLDER RETAINING SPRING - LONG 1
G20184 WIRE HOLDER RETAINING SPRING FOOT 1
G20186 FEED GEAR FRICTION SPRING 1
G20187 FEED GEAR FRICTION STRIP 1
G20189 SCREW M3X.5X20 3
G20195 SET SCREW M6X1X8 2
G20196 SCREW M3X0.5X6 SHCS 4
G20241 M4X0.7X6MM SOCKET HEAD CAP SCREW 2
G20256B CUTTER BLOCK SCALE 1
G20261B WIRE HOLDER SPRING STUD 1
G20298 NYLOCK LOCK NUT, M6X1 1
G20316 WIRE HOLDER SPRING - SHORT 1
G20579 SCREW, M4X0.7X6-FHM-SLOTTED 2

G20139A Replaced By G20139BA Feed Lever Assembly

G20139 PIVOT BLOCK INSERT, 1/2” CROWN 1 G20112 SMALL FEED GEAR 1
G20143 ADJUSTMENT RACK 1 G20132 FEED LEVER 1
G20196 SCREW M3X.5X6 SHCS 2 G20140 FOLLOWER BALL BEARING 1
G20214 SCREW M4X0.7X8 FHMS 2 G20262A FEED LEVER PIN ASSEMBLY 2
G20229 SCREW, M6X1.0X12, NYLON 1 G20263 FEED LEVER E-RING 2
G20256 CUTTER BLOCK SCALE, G8 1 G20264 SCREW M5X.8X5 SHCS 1
G20273 SCREW M4X.7X4 SHSS 1 G20266 FOLLOWER BEARING PIN 1
G20541 WIRE GUIDE BAR, LEFT 2 G20267 FEED LEVER BUSHING 1
G20579 SCREW M4X0.7X6 2 G20268 FEED LEVER SPRING 1

36
Driving and Feed Slide Assemblies

G20264 G20173

G20340
(OLD STYLE) G20131 G20179

G20177
G20130

G20176 (2)
G20174

G20340

G20127

G20162BA G20320A
Complete G20171 G20171 Complete
Assembly Assembly
G20321
G20170

G20162
G20170 G20320
G20169B

G20165 G20165

G20163A G20167
G20163A
G20167 G20164B
G20164B

For rail-driven Heads For crank-driven Heads

37
 Driving Slide Assembly
G20127 FEED RACK 1
G20130 FEED ADJUSTMENT BLOCK 1
G20131 FEED SLIDE 1
G20173 FEED RACK KNOB - KNURLED 1
G20174 FEED RACK ADJUSTMENT STUD 1
G20176 SCREW M4X.7X12 SHCS LOW HEAD 2
G20177 FEED RACK ADJ KNOB POINTER 1
G20179 SCREW M3X.5X4, SHCS 1
G20264 SCREW M5X.8X5 SHCS 1
G20340 CRANK DRIVE LINK 1

G20320A Driving Slide Assembly - Crank Drive

G20163A CUTTER OPERATING RAMP ASSEMBLY 1
G20164B DRIVING SIDE PLUNGER 1
G20165 DRIVING SLIDE SPRING 1
G20167 SCREW, M4X0.7X10 FHCS 2
G20170 HEX JAM NUT M8X1.25 1
G20171 SCEW, M8X1.25X12 1
G20320 DRIVING SLIDE - CRANK DRIVE 1
G20321 CRANK LINK SCREW 1
G20163A CUTTER OPERATING RAMP ASSEMBLY 1

Feed Slide Sub-Assemblies

G20162BA Driving Slide Assembly

G20162 DRIVING SLIDE 1
G20163A CUTTER OPERATING RAMP ASSEMBLY 1
G20164B DRIVING SIDE PLUNGER 1
G20165 DRIVING SLIDE SPRING 1
G20167 SCREW, M4X0.7X10 FHCS 2
G20169B DRIVING SLIDE PLUNGER SCREW ECCENTRIC 1
G20170 HEX JAM NUT M8X1.25 1
G20171 SCEW, M8X1.25X12 1

38
Bender Bar and Wire Holder Assemblies

G20147BAA (24/25 rd)

STANDARD
G20347BAA (21x25 flat)
G20161

G20160B

G20159

G20224
G20342 G20149

G20344 G20150

G20148B

G20147B
G20154A

G20346B (PLASTIC)
G20156 G20433
G20155
G20559BA G20147BA (24/25 RD)
G20252 STANDARD
Complete
Assembly G20151 G20347BA (21x25 FLAT)
G20357BA (23 RD)
G20253 G20377BA (20x24 FLAT)
G20255

G20665 G20152 (24/25 RD)

STANDARD
G20352 (21X25 FLAT) G20153
G20254 G20358 (23 RD)

G20226
G20559B
(WITHOUT COMPONENTS) G20273

39
G20147BAA Bender Bar/Driver Assembly (24/25 RD)
STANDARD
G20147BA BENDER BAR ASSEMBLY, 24W 1
G20149 BENDER BAR LATCH 1
G20150 BENDER BAR LATCH SPRING 1
G20151 DRIVER BAR 1
G20152 DRIVER, 24W 1
G20153 DRIVER RETAINING SCREW 2
G20154A SUPPORTER ASSEMBLY 1
G20155 SUPPORTER PIVOT PIN 1
G20156 SUPPORTER PIVOT PIN SCREW 1
G20159 BENDER BAR FRICTION PLUG 1
G20160B BENDER BAR FRICTION SPRING 1
G20161 BENDER BAR FRICTION BUSHING 1
G20224 BENDER BAR LATCH SPRING SCREW 1
G20342 SUPPORTER SPRING PLUNGER 1
G20344 SUPPORTER SPRING 1

G20347BAA Bender Bar/Driver Assembly (21x25

Wire)
G20347BA BENDER BAR ASSEMBLY, 21X25W 1

G20357BAA Bender Bar/Driver Assembly (21x25 Wire)

G20357BA BENDER BAR ASSEMBLY, 23W 1
G20358 DRIVER, 23W 1
G20377BA Bender Bar Assembly (20x24 Flat)
G20148B LATCH HOUSING, REMOVABLE 1
G20377B BENDER BAR, 20X24 WIRE 1
G20433 SCREW, M2.5X.45X12 4

G20599BA Wire Holder Assembly 1/2 Cr

G20226 HEX NUT M4X.7 1
G20252 WIRE HOOK 1
G20253 WIRE HOOK SPRING 1
G20254 WIRE HOOK SPRING SCREW 1
G20255 HOOK PIVOT PIN 1
G20273 SCREW M4X0.7X4 SHSS 1
G20559B WIRE HOLDER 1/2 CR 1
G20665 WIRE HOLDER ECCENTRIC SCREW 1

40
 Cutter Block Assembly
G20197BAA (round wire)
G20197FAA (flat wire) G20145 (STANDARD)
Complete Assembly (ROUND WIRE)
(All parts on this page) G20145C (CARBIDE)
G20145F (FLAT WIRE)
G20210
G20214 APPLY GREASE
APPLY BLUE LOCTITE
TO THREADS G20197A
G20198
G20200 (STANDARD)
G20226 (2) G20200C(CARBIDE)
Available for use with 25 or
24 gauge wire only.

G20216

G20219 (4)

G20191

OLD STYLE
LOWER WIRE TUBE
PARTS G20196B
APPLY BLUE
LOCTITE
TO THREADS

G20199B-1 G20212
G20199A G20208D (round wire) G20208B
G20199B-2
G20208E (flat wire) G20213
DW1058
APPLY BLUE LOCTITE
TO THREADS
G20206

LOWER WIRE TUBE UPGRADE KITS

---------------------------------------------------
ORDER KIT NUMBER: G20199BAA (round wire)
G20206
KIT INCLUDES:
• G20199B-1, (1)
G20208B • G20199B-2, (1)
• G20208D, (1)
* 071004 G20213 • G20213, (2)

* G20196 *G20211 • DW1058 (1)

ORDER KIT NUMBER: G20199FAA (flat wire)

KIT INCLUDES:
• G20199B-1, (1)
* these parts must be removed before lower wire • G20199B-2, (1)
tube upgrade kit installation (G20199BAA or • G20208E, (1)
20199FAA) • G20213, (2)
• DW1058 (1)

41
 Cutter Block Assembly
G20197BAA (ROUND WIRE)
G20197FAA (FLAT WIRE)
Complete Assembly
(All parts on this page)

DW1058 SCREW, M4 X 6, BUTTON HEAD 1

G20145 MOVING CUTTER-RND WIRE (STANDARD) 1
G20145C MOVING CUTTER - (CARBIDE)
G20145F MOVING CUTTER - (FLAT WIRE)
G20191 SCREW, M4X.7X8 SHSS 2
G20196 SCREW M3X.5X6 SHCS (OLD STYLE) 1
G20196B SCREW M3X.5X6 SHCS 1
G20197A CUTTER BOX ASEMBLY 1
G20198 CUTTER OPERATING SLIDE 1
G20199A LOWER WIRE TUBE ASSEMBLY (OLD) 1
G20200 FIXED WIRE CUTTER (STANDARD) 1
G20200C FIXED CUTTER - (CARBIDE)
G20206 WIRE STRAIGHTENER ECCENTRIC 1
G20208B WIRE STRAIGHTENER ROLLER 1
G20210 CUTTER OPERATING SPRING 1
G20214 SCREW M4X0.7X8 FHMS 1
G20216 SCREW, M4 X 0.7 X 25 2
G20219 WIRE STRAIGHTENER DISC SPRING 4
G20226 HEX NUT M4X.7 2
G20211 CUTTER WIRE SHIELD (OLD STYLE) 1
G20212 WIRE STRAIGHTENER ROLL STUD 1

Lower Wire Tube Assembly, G8 Round Wire, Upgrade Kits

G20199BAA (ROUND WIRE)
G20199FAA (FLAT WIRE)
071004 LOCK WASHER, M3 (OLD STYLE) 1
G20199B-1 LOWER WIRE TUBE BASE, G8 1
G20199B-2 LOWER WIRE TUBE COVER, G8 1
G20213 WIRE STRAIGHTENER ROLL CLIP 2
G20208D WIRE STRAIGHTENER ROLLER UPPER, ROUND 1
G20208E WIRE STRAIGHTENER ROLLER UPPER, FLAT 1

42
 G50286SA
(FOR USE ON
Wire Guide Bracket, Spring and Clincher Plate STITCHMASTER)

NOTE:
GUIDE SPRING REVERSED. G20293B

G20293
G20279A
G20292

G20679A

G20286A

G50808
G20241 (2) G20298
G20287
7257B ROUND WIRE G20292
(STANDARD) G20297
G20293 (2)
7024B FLAT WIRE

G50800CA

USED ON
M MACHINE
G20288 (2) G50806
G20292
7253A
G20293
18184
G20293B
CA9083A (STANDARD)
18182 (FOR ROUND WIRE.)
9083C (FOR FLAT WIRE.)

UA3216.2

18183 G20288

18186 9086A (STANDARD)

38
FOR M2
CT9088 (2)
9086JA G50710 (2) 9086TA G50710 (2) CA2091 (2)

UA4808.7
9084B
OPTIONAL OPTIONAL
9087
CT9093A (STANDARD)

43
Wire Guide Bracket, Spring and Clincher Plate Assemblies
38 CLINCHER SLIDE ADJUSTMENT SCREW 1
9087 CLINCHER SLIDE ADJUSTING SCREW 1
18182 CLINCHER SLIDE 1
18183 CLINCHER SLIDE ADJUSTMENT BLOCK 1
18184 CLINCHER SLIDE BLOCK CLAMP 1
18186 CLINCHER SLIDE ADJUSTMENT SCREW 1
7024B CLINCHER POINT - FLAT 2
7253A CLINCHER PLATE ASSEMBLY - 1/2 1
7257B CLINCHER POINT - ROUND (STANDARD) 2
9083C CLINCHER POINT - 20X24, FLAT 2
9084B ADJUSTABLE CLINCHER SLIDE 1
9086A CLINCHER PLATE - THICK (STANDARD) 1
9086JA CLINCHER PLATE - THICK 1
9086TA CLINCHER PLATE, THICK 1
CA2091 CLINCHER PLATE BINDER NUT 2
CA9083A CLINCHER POINT - (STANARD) 2
CT9088 CLINCHER PLATE BINDER BOLT 2
CT9093A CLINCHER SLIDE - THICK (STANDARD) 1
G20241 SCREW M4X0.7X6 SHCS 2
G20287 WIRE OILER FELT SPRING 1
G20288 SCREW, M4X.7X8 SHCS 2
G20292 WIRE OIL FELT WASHER 1
G20293 WIRE OILER FELT 2
G20293B WIRE OILER FELT, THIN 1
G20297 SCREW, M6X1X40 SHCS 1
G20298 NYLOCK LOCK NUT, M6X1 1
G50710 CLINCHER PLATE NUT 2
G50800CA ANTI-WIRE BACKUP UNIT 1
G50806 FELT MOUNTING BRACKET 1
G50808 WIRE SPRING GUIDE CLAMP PLATE 1
UA3216.2 CLINCHER SLIDE BLOCK SCREW 2
UA4808.7 SET SCREW, 1/4-28X1/2", SH 1

ONE OF THE FOLLOWING:

G20279A GUIDE SPRING ASSEMBLY - MEDIUM
G20286A GUIDE SPRING ASSEMBLY - LONG
G20679A GUIDE SPRING ASSEMBLY - SHORT
G50286SA GUIDE SPRING ASSEMBLY - STITCHMASTER

44
 Loop Stitch Kit G8KL Loop Conversion Kit includes all parts shown below.

G20300BAA
Complete Assembly G20210

G20214

G20198

G20145

G20300A

G20219
G20200

G20226

G20191

G20196B
G20216

G20212

G20199B-1 G20206
G20208D G20213
G20199B-2 G20208B

DW1058

45
G20300BAA Cutter Box Complete, Loop
Round - 2 pc Wire Tube (24/25 rd) STANDARD
DW1058 SCREW, M4 X 6, BUTTON HEAD 1
G20145 MOVING CUTTER - ROUND WIRE 1
G20191 SCREW, M4X.7X8 SHSS, NYLON 2
G20196B SCREW, M3X0.5X6 1
G20198 CUTTER OPERATING SLIDE 1
G20199B-1 LOWER WIRE TUBE BASE 1
G20199B-2 LOWER WIRE TUBE COVER 1
G20200 FIXED WIRE CUTTER 1
G20206 WIRE STRAIGHTENER ECCENTRIC 1
G20208B WIRE STRAIGHTENER ROLLER 1
G20208D WIRE STRAIGHTENER ROLLER UPPER 1
G20210 CUTTER OPERATING SPRING 1
G20213 WIRE STRAIGHTENER ROLL CLIP 2
G20214 SCREW M4X0.7X8 FHMS 1
G20216 SCREW M4X.7X25 SFHS 2
G20219 WIRE STRAIGHTENER DISC SPRING 4
G20226 HEX NUT M4X0.7 2
G20300A CUTTER BLOCK ASSEMBLY - LOOP 1
G20226 HEX NUT M4X0.7 1

46
 G20161
G20317AA
Complete Assembly

G20160B

G20159
G20342

G20224
G20344W G20149
G20147BA
G20150

G20313A

G20346B

G20156
G20155

G20151

G20314
(25 Round)

G20153 (2)

47
G20317AA Bender/Driver Assembly, Loop
G20147BA BENDER BAR ASSEMBLY, 24W 1
G20149 BENDER BAR LATCH 1
G20150 BENDER BAR LATCH SPRING 1
G20151 DRIVER BAR 1
G20153 DRIVER RETAINING SCREW 2
G20155 SUPPORTER PIVOT PIN 1
G20156 SUPPORTER PIVOT PIN SCREW 1
G20159 BENDER BAR FRICTION PLUG 1
G20160B BENDER BAR FRICTION SPRING 1
G20161 BENDER BAR FRICTION BUSHING 1
G20224 SCREW M3 X 0.5 X 6 1
G20313A SUPPORTER ASSEMBLY - LOOP 1
G20314 DRIVER - LOOP 1
G20342 SUPPORTER SPRING PLUNGER 1
G20346B SUPPORTER GUIDE PIN, COMPOSITE 1
G20344W SUPPORTER SPRING - WATKISS 1

48
 G20301A
Complete Assembly G20135

G20304A

G20307B
G20226

G20306
G20310

G20311

G20309A
G20273

G20301
G20312 G20305

G20309
G20665

G20301A Wire Holder Assembly, Loop

G20135 DOWEL PIN M5X24 1
G20226 HEX NUT M4X0.7 1
G20273 SCREW M4X.7X4 SHSS 1
G20310 WIRE HOLDER ROLLER LEVER SPRING 1
G20311 SPRING ANCHOR SCREW 1
G20312 SPIROL PIN M3X12 1
G20301 WIRE HOLDER, LOOP 1
G20304A WIRE HOOK ASSEMBLY - LOOP 1
G20305 ANVIL - LOOP 1
G20306 SCREW M3X.5X25-SHC 1
G20307B LEVER PIVOT SCREW, LOOP 1
G20309 WIRE HOLDER LEVER BLANK, LOOP 1
G20309A WIRE HOLDER LEVER ASSEMBLY, LOOP 1
G20665 WIRE HOLDER ECCENTRIC ADJ SCREW 1

49
 Optional Equipment

In addition to the standard features offered with the G8 Stitcher Head, optional equipment items can
be purchased to better accommodate your stitching needs. The following kits can be purchased from
your Graphic Arts Representative.

G8KC

The G8 Crank Drive Kit is available to owners of all styles of rail-driven G8 Heads who need to
convert, for whatever reason, their existing G8 head to a crank-driven model. Included in this Kit
are the Rear Clamp Pin, Rear Mounting Bolt, Bonnet Stud Nut, the Crank Drive Link and a complete
assembly of the Link-Driven Driving Slide.

For more information about purchasing the G8KC or for technical support when making the
conversion from rail-driven to crank-driven, contact your local Graphic Arts Representative.

Always disconnect the power supply before 

! WARNING
making any adjustments or servicing the head.

G8KL-Loop Stitch Conversion Kit

The standard G8 Head with 24 gauge wire can be converted to a Loop style by exchanging the
following three sub-assemblies: the Wire Holder Assembly, the Cutter Block Assembly and the
Bender Bar Assembly.

Contact your DeLuxe Stitcher Graphic Arts Representative or the DeLuxe Stitcher Customer
Service Department for ordering information or for additional technical information on other wire
sizes available in Loop Stitch.

G20300BAA G20139LA

G20301A G20317AA G20316

Figure 36 - Loop Stitch Kit

50
 G8KS-Stop Stitch Kit

The G8KS mounts on the Adjustment Rail of McCain Saddle Stitchers. It stops the feeding of wire
through the Stitcher Heads by pushing open the Feed Release Handles (stopping the stitch) when it
receives a signal from the calipers of the Stitcher.

The G8KS Stop Stitch Kit comes complete with all the components necessary for converting
your existing stitcher machine, along with fully illustrated instructions. Call your Graphic Arts
Representative for more information.

Always disconnect the power supply before 

! WARNING
making any adjustments or servicing the head.

G8KT-Stop Stitch Toggle Kit

The G8KT is a Stop Stitch Toggle Kit specifically designed for users of McCain Stitchers using both
26/26D and G8 Stitcher Heads.

The Electrical Box, Box Cover and Toggle Switch replace your machine’s existing equipment to
make switching between the two styles of Stitcher Heads easier. This Kit comes complete with a wir-
ing diagram and replacement electrical box. For more information or technical support, contact your
local Graphic Arts Representative.

51
 Part Number / Description Cross-Reference
G20130 Feed Adjustment Block 1
072001 Screw M4x0.7x8 1
G20131 Feed Slide 1
071004 Lock Washer, M3 1
G20132 Feed Lever 1
18182 Clincher Slide 1
G20133A Feed Release Spring Block Assembly 1
18183 Clincher Slide Adjustment Block 1
G20135 Dowel Pin M5x24 1
18184 Clincher Slide Block Clamp 1
G20136BA Feed Gear Bracket Assembly 1
18186 Clincher Slide Adjustment Screw 1
G20137 Roller Clutch Bearing 1
CA2091 Clincher Plate Binder Nut 2
G20138 Feed Pinion Bearing 2
38 Clincher Slide Adjustment Screw 1
G20139 Pivot Block Insert 1
7024B Clincher Point - Flat 2
G20139LA Pivot Block Assembly, G8 Loop Optional
7253A Clincher Plate Assembly - 1/2 1
G20140 Follower Ball Bearing 1
7257B Clincher Point - Round 2
G20143 Cutter Block Adjustment Rack 1
9002 Bonnet Clamp Block 1
G20144A Middle Wire Tube Assembly 1
CA9083A Clincher Point - Thick, Round 2
G20145 Moving Cutter - Round Wire 1
9083C Clincher Point - 20x24, Flat 2
G20145C Moving Cutter - Carbide 1
9084B Adjustable Clincher Slide 1
G20145F Moving Cutter - Flat Wire 1
9086A Clincher Plate - Thick 1
G20147BA Bender Bar Assembly, 24W 1
9086JA Clincher Plate - Thick 1
G20148B Latch Housing, Removable 1
9087 Clincher Slide Adjusting Screw 1
G20149 Bender Bar Latch 1
CT9088 Clincher Plate Binder Bolt 2
G20150 Bender Bar Latch Spring 1
CT9093A Clincher Slide - Thick 1
G20151 Driver Bar 1
G20000A Bonnet Assembly - G8 1
G20152 Driver, 24W 1
G20110A Large Feed Gear Assembly 1
G20153 Driver Retaining Screw 2
G20111A Feed Pinion Assembly 1
G20154A Supporter Assembly 1
G20112 Small Feed Gear 1
G20155 Supporter Pivot Pin 1
G20113 Supporter Guide Plate 2
G20156 Supporter Pivot Pin Screw 1
G20114 Feed Pinion Shaft 1
G20159 Bender Bar Friction Plug 1
G20115 Latch Release Cam 1
G20160B Bender Bar Friction Spring 1
G20118 Feed Release Handle Cam 1
G20161 Bender Bar Friction Bushing 1
G20119 Feed Release Handle 1
G20162 Driving Slide 1
G20121 Feed Release Plunger 1
G20162BA Driving Slide Assembly Eccentric 1
G20122A Feed Slide Retaining Screw Asy 2
G20163A Cutter Operating Ramp Assembly 1
G20124 Bonnet Clamp Eccentric 1
G20164B Driver Slide Plunger Eccentric 1
G20126 Tube Pivot Plate 1
G20165 Driving Slide Spring 1
G20127 Feed Rack 1
G20167 Screw, M4x.7x10 FHCS 4
G20128 Large Feed Gear Washer 1
G20169B Driving Slide Plunger Screw Ecc 1
G20129 Small Feed Gear Washer 1
G20170 Hex Jam Nut M8x1.25 1

52
G20171 Screw M8x1.25x12 1 G20216 Screw M4x.7x25 SFHS 2

G20173 Feed Rack Knob - Knurled 1 G20217 Spirol Pin M5x12 1

G20174 Feed Rack Adjustment Stud 1 G20219 Wire Straightener Disc Spring 4

G20175 Screw M4x.7x6 SHCS 3 G20220 Hex Nut M5x.8 1

G20176 Screw M4x.7x12 SHCS Low Head 2 G20223 Dowel Pin 1/8x1/4 1

G20177 Feed Rack Adj Knob Pointer 1 G20224 Bender Bar Latch Spring Screw 1

G20179 Screw M3x.5x4, SHCS 1 G20226 Hex Nut M4x.7 2

G20180 Flat Washer M6 1 G20228A Adjustment Handle Assembly 1

G20181 Upper Wire Tube 1 G20229 Set Screw M6x1x12 2

G20182 Feed Gear Shaft Plate 1 G20230A Cutter Operating Lever Assembly 1

G20183 Wire Holder Retaining Spring - Long 1 G20231 Cutter Operating Lever Pivot Pin 1

G20184 Wire Holder Retaining Spring Foot 1 G20232 Cutter Operating Lever Roll Pin 1

G20186 Feed Gear Friction Spring 1 G20233 Cutter Operating Lever Roller 1

G20187 Feed Gear Friction Strip 1 G20234 E-Ring- 3/16" 1

G20188 Dowel Pin, 1/8"x3/8" 4 G20235 Follower Bearing Shaft 1

G20189 Screw M3x.5x20 3 G20236 Tube Pivot Screw 1

G20190 Screw M3x.5x10- FHMS- Slotted 4 G20237B Cutter Block Adjustment Stud 1

G20191 Screw, M4x.7x8 SHSS 5 G20240 Cutter Block Adjustment Washer 2

G20195 Set Screw M6x1x8 2 G20241 Screw M4x0.7x6 SHCS 4

G20196 Screw M3x.5x6 SHCS 8 G20242 Cutter Adjustment Bar - Lower 1

G20197A Cutter Block Assembly 1 G20243 Dowel Pin 1/4x9/16 1

G20198 Cutter Operating Slide 1 G20244 Tube Pivot Clip 1

G20199A Lower Wire Tube Assembly 1 G20245 Cutter Adjustment Bar - Upper 1

G20199B-1 Lower Wire Tube Base 1 G20246 Cutter Block Adjustment Connect 1

G20199B-2 Lower Wire Tube Cover 1 G20249 Cutter Block Washer 2

G20200 Fixed Wire Cutter 1 G20250 Screw M4x.7x14 2

G20202 Cutter Block Slide Plate 1 G20251 Cutter Adjustment Bar - Upper 1

G20204 Upper Cutter Block Guide 1 G20252 Wire Hook 1

G20206 Wire Straightener Eccentric 1 G20253 Wire Hook Spring 1

G20208B Wire Straightener Roller 2 G20254 Wire Hook Spring Screw 1

G20208D Wire Straightener Roller Upper, Rd Wire 2 G20256 Cutter Block Scale 1

G20210 Cutter Operating Spring 1 G20261B Wire Holder Spring Stud 1

G20211 Cutter Wire Shield 1 G20262A Feed Lever Pin Assembly 2

G20212 Wire Straightener Roll Stud 1 G20263 Feed Lever E-Ring 2

G20213 Wire Straightener Roll Clip 2 G20264 Screw M5x.8x5 SHCS 5

G20214 Screw M4x0.7x8 FHMS 5 G20266 Follower Bearing Pin 1

53
G20267 Feed Lever Bushing 1 G20344B Supporter Spring - Heavy 1

G20268 Feed Lever Spring 1 G20346 Supporter Guide Pin 1

G20269 Spirol Pin 3/16x5/8 1 G20347BA Bender Bar Assembly,21x25 1

G20273 Screw M4x.7x4 SHSS 2 G20352 Driver, 21x25W 1

G20274 Hex Jam Nut, M6x1 1 G20353 Driver, 20x24W 1

G20275 Ball Spring Plunger 1 G20357BA Bender Bar Assembly, 23W 1

G20279A Wire Guide Spring Assembly - Medium 1 G20358 Driver, 23W 1

G20286A Wire Guide Spring Assembly - Long 1 G20360 Hex Key Wrench 3.0mm 1

G20287 Wire Oiler Felt Spring 1 G20361 Hex Key Wrench 2.5mm 1

G20288 Screw, M4x.7x8 SHCS 4 G20362 Clamp Wrench 5.0mm 1

G20289 Screw M4x.7x16 2 G20364 Open End Wrench 1

G20292 Wire Oil Felt Washer 1 G20366 Rear Clamp Pin 1

G20293 Wire Oiler Felt 1 G20367 Rear Mounting Bolt 1

G20297 Screw, M6x1x40 SHCS 1 G20368 Feed Release Handle Cap 1

G20298 Nylock Lock Nut, M6x1 1 G20371 Feed Release Handle 1

G20300A Cutter Block Assembly - Loop 1 G20372 Feed Release Shaft 1

G20301A Wire Holder Assembly - Loop 1 G20374 Hex Key Wrench 2.0mm 1

G20304A Wire Hook Assembly - Loop 1 G20377B Bender Bar, 20x24W 1

G20305 Anvil - Loop 1 G20433 Screw, M2.5x.45x12 4

G20306 Screw M3x.5x25-SHC 1 G20541B Wire Guide Bar Left 2

G20307 Lever Pivot Pin 1 G20559BA Wire Holder Assembly 1/2 1

G20309A Wire Holder Lever Assembly - Loop 1 G20579 Screw, M4x0.7x6-FHM-Slotted 2

G20310 Wire Holder Roller Lever Spring 1 G20600C Fixed Cutter - Carbide 1

G20311 Spring Anchor Screw 1 G20617 Washer M6 1

G20312 Spirol Pin M3x12 1 G20665 Wire Holder Eccentric Adj Screw 1

G20313A Supporter Assembly - Loop 1 G20679A Wire Guide Spring Assembly-Short 1

G20314 Driver - Loop 1 G50268 Feed Lever Spring, G5 1

G20316 Wire Holder Retaining Spring - Short 1 G50286SA Wire Guide Spring Assembly-Short 1

G20320 Driving Slide - Crank Drive 1 G50394 Flat Washer - M8 1

G20320A Driving Slide Assembly 1 G50710 Clincher Plate Nut 2

G20321 Crank Link Screw 1 G50716 Mounting Block Handle 1

G20323A Cutter Operating Ramp Assembly 1 G50800CA Anti-Wire Backup Unit 1

G20340 Crank Drive Link 1 G50808 Wire Spring Guide Clamp Plate 1

G20341 Rear Mounting Bolt 1 HN1213 Bonnet Stud Nut 1

G20342 Supporter Spring Plunger 1 UA3216.2 Clincher Slide Block Screw 2

G20344 Supporter Spring 1 UA4808.7 Set Screw, 1/4-28x1/2", SH 1

54
 LIMITED WARRANTY

DeLuxe Stitcher Company warrants to the original retail purchaser

that this product is free from defects in material and workmanship and
agrees to repair or replace, at DeLuxe Stitcher’s option, any defective
product within 90 days from the date of purchase. This warranty is not
transferable. It covers damage resulting only from defects in material or
workmanship and does not cover conditions or malfunctions resulting from
normal wear, neglect, abuse or accident.

This warranty is in lieu of all other express warranties. Any warranty of

merchantability or fitness for a particular purpose is limited to the duration
of this warranty. DeLuxe Stitcher shall not be liable for any incidental or
consequential damages.

Some states do not allow limitations on how long an implied warranty lasts,
or the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights which
vary from state to state.

To obtain warranty service you must return the product, at your expense,
together with proof of purchase to an authorized
DeLuxe Stitcher Company Graphic Arts Dealer.

55
NOTES:

56
 R E G I ST R AT ION
To better service your wire stitching needs, please
take a moment to fill out and return this registration card.
Please take a moment to fill out the attached card
and mail it to DeLuxe Stitcher Company, Inc. Name :
( First ) ( Middle Initial ) ( Last )
In addition, duplicate the information for your
Company :
records to assist when making further inquiries.
Street Address :
City : State/Province : Zip :
Country :

CUSTOMER
PRODUCT Phone : Fax : E-mail :
Machine(s) Purchased :
Serial Number(s) : Machine(s) Purchased :

With Head(s) : Serial Number(s) :

( Type/Quantity Purchased )
With Head(s) :
( Type/Quantity Purchased )
Serial Number(s) :
Head(s) Purchased : Serial Number(s) :
Serial Number(s) :
P R O D U C T
Head(s) Purchased :
Serial Number(s) :

DE LUXE STITCHER GRAPHIC ARTS REPRESENTATIVE Date Received :

Date Received : Dealer Name :
Dealer Name : Dealer Street Address :
Dealer Street Address : City : State/Province : Zip :
City : State/Province : Zip : Country :
D E A L E R

Country : Dealer Phone :

Dealer Phone :
Other Bindery Products Used :

Would you like information sent to you about new products

that would benefit your company?  Yes  No
Common Replacement Parts for 1/2” Crown

Below is a list of the most common wear/replacement parts for

the G8 Stitcher Head. This guide should help you when ordering
replacement parts. If the part you need is not listed below,
please refer to the more detailed parts list on pages 38-40 in this
manual.

Description Item Number

Clincher Point - Thick, Round CA9083A

Latch Release Cam G20115
Feed Slide Retain Screw Asy G20122A
Follower Ball Bearing G20140
Moving Wire Cutter G20145
Bender Bar Latch G20149
Bender Bar Latch Spring G20150
PLACE
Driver Bar G20151
Driver, 24W G20152 STAMP
Driver Retaining Screw G20153 HERE
Bender Bar Friction Plug G20159
Bender Bar Friction Spring G20160B
Wire Holder Retaining Spring Foot G20184
Feed Gear Friction Strip G20187
DeLuxe Stitcher
Fixed Wire Cutter G20200 COMPANY INC.
Wire Hook G20252 3747 N. Acorn Lane
Franklin Park, IL 60131U.S.A.
Lever Pivot Pin G20307
Attn: Customer Service

* You can purchase the G8RPK which includes these and other common replacement
parts.
59
®
DELUXE STITCHER
ISP Stitching & Bindery Products
C O M P A N Y I N C .

3747 Acorn Lane • Franklin Park • Illinois 60131

Phone: 847-455-4400 • 800-634-0810
Fax: 847-455-4900 • 800-417-9251
http://www.deluxestitcher.com

DBSG8_0816