Scribd
Upload
189 views

Design of Base Plate Mkd. BP1: Goal Seek

The document describes the design of a base plate including design parameters, dimensions, material properties, and load calculations. It specifies the length, thickness, bolt diameter, grades of steel and concrete, and other properties. Load cases are considered including axial load, moment, and eccentricity. Stress is calculated for different sections and checked against allowable values. Tension and shear stresses are also checked for individual bolts.

Uploaded by

viv99844
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
189 views

Design of Base Plate Mkd. BP1: Goal Seek

The document describes the design of a base plate including design parameters, dimensions, material properties, and load calculations. It specifies the length, thickness, bolt diameter, grades of steel and concrete, and other properties. Load cases are considered including axial load, moment, and eccentricity. Stress is calculated for different sections and checked against allowable values. Tension and shear stresses are also checked for individual bolts.

Uploaded by

viv99844
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 3

DESIGN OF BASE PLATE

Mkd. BP1

Design Parameters

Length of the baseplate along Z (D) = 600 mm


Length of the baseplate along X (B) = 600 mm
Thickness of baseplate(t) = 20 mm
Thickness of stiffener plate = 12 mm

Diameter of bolt(d) = 20 mm
Grade of concrate = M30 X
Modulus of elasticity of steel(Es) = 210000 MPa
Modulus of elasticity of concrete(Ec) = 28500 MPa
Value of n(Es/Ec) = 7.37
Allowable bearing stress on pedestal = 10.0 Mpa
Let no. of bolts on each side = 4
Net area of bolt provided on each suide(As) = 1004.8 mm2
For baseplate(fy) = 262.5 MPa
Distance between C.L.of column & bolts(f) = 250 mm
Edge distance along X direction = 62.5 mm
Edge distance along Z direction = 50 mm
Distance between adjacent bolts in a line along Z = 500 mm

Check on Dimensions

Distance between adjacent bolts in a line = 500 mm


Edge distance along Z-Z direction = 50 mm OK
Edge distance along X-X direction = 62.5 mm OK

Design of baseplate

Load case

Axial load(P) = 56.3 T


Moment(Mx) = 20.1 T-m 20.1
Goal Seek
Ecentricity(e) = 357.02 mm > D/6

K1=3*(e-D/2) = 171.0479573712 mm
K2 = 6*n*As(f+e)/B= 44942.18565953 mm2 Refer "Design of Welded Structures" by Blodgett
K3 = -K2*(D/2+f) = -24718202.1127 mm3
For Y = 317.85 mm
F(Y) =
F(Y) = Y3+K1*Y2+K2*Y+K3 = 38958094 Refer "Design of Welded Structures" by Blodgett
When e<D/6,then maximum sc = 1.569472222
Pc = 563 KN
Pt = 206.61893881 KN

sc = 8.07116 MPa OK

Exterior panel :- 119


Z

a = 119 mm a/b 0.125 0.25 0.375 0.5 0.75 1


a b = 204 mm Formula for b1 0.05 0.182 0.353 0.631 1.246 1.769
b a/b = 0.58 stress & strain b2 0.047 0.188 0.398 0.632 1.186 1.769
b1 = 0.84 by Roark & g1 0.312 0.572 0.671 0.874 1.129 1.183
X Young. Table g2 0.127 0.264 0.413 0.557 0.829 1.183

(At X=0, Z=0)


sb = -702.01 MPa NOT OK 702.008999211
Tension with bending :-

Tension = 507.84 kN
Tension on each bolt = 42.32 kN
Moment = 51.26 kN-m
Tension due to push-pull action of moment = 23.30 kN

Total Tension on each bolt = 65.620 kN

Now, Maximum Shear = 401.38 kN


Shear on each bolt = 33.45 kN

n= Coefficient for shear & tension interaction check = 1

Bolt capacities as per 10080-SD-CS-63073 for M30 bolts

In shear (Fs) = 58.33 KN In tension (Ft) = 140.00 KN (Load factor = 1.2)


Increasing permissible streeses 25% for wind/seismic loads
In shear (Fs) = 72.92 KN In tension (Ft) = 175.00 KN

Tension Shear interaction = (fs / Fs)n + (ft / Ft)n = 0.83 OK

You might also like