TRAINER DEVELOPMENT PROGRAM

(TDP)

INSTRUCTIONS : Each question is a multiple-choice question with four answer choices.

2 Read each question and answer choice carefully and choose the ONE best answer.
3 Each question carry 2 marks, 1mark will deducted for every wrong answer.
4 Time for completion of exam is 30 minutes only.

Prepared
Prepared By:
By:
RAVI
RAVI KUMAR
KUMAR SHARMA
SHARMA
ROGRAM

r choices.
he ONE best answer.
wrong answer.

Click to start the

Exam Portal
Trainer Name :
Employee ID :
Email ID :
Location :
Click to Start the Exam
Trainer Name : 0
ID Number : 0
Email ID : 0
Location : 0
COURSE NAME : AUTOMOTIVE MANUFACTURING

TOPIC : BASICS OF AUTOBILE ENGINEERING

Multiple-choice questions with four options.
1-During the compression stroke of a four stroke diesel engine, the
piston compresses.
(A) Air-fuel mixture
(B) Atomized diesel
(C) Diesel vapor
(D) Air
2-The inventor of two stroke engine is
(A) Dugald Clerk
(B) Rudolf diesel
(C) James Watt
(D) Nicolas A Otto
3-Theoritically during expansion process in a four stroke engine
(A) Inlet valve opens and exhaust valve closes
(B) Inlet valve closes and exhaust valve opens
(C) Both valve remains closed
(D) Both valve remains opened
4-The nominal volume of cylinder when piston is at TDC is called
(A) Stroke volume
(B) Swept volume
(C) Clearance volume
(D) Suction volume
5-Which of the following engine can operate at higher speed?
(A) Square engine
(B) Over square engine
(C) Under square engine
(D) Steam engine
6-The process of flushing out the products of combustion from the
engine cylinder by fresh charge is known as
(A) Turbo charging
(B) Super charging
(C) Scavenging
(D) None of the above
7-When the piston of a two stroke engine single cylinder engine move
from BDC to TDC
(A) transfer port opens and intake port closes
(B) exhaust port open and transfer port closes
(C) exhaust port and transfer port opens
(D) none of the above
8-The number of crankshafts for opposed piston engine is
(A) one
(B) two
(C) three
(D) four
9-The ratio of brake thermal efficiency to indicated thermal efficiency
is known as
(A) Mechanical efficiency
(B) Relative efficiency
(C) Air standard efficiency
(D) Calorific value efficiency
10-Chemically correct air fuel mixture ratio for SI engine is around
(A) 15:1
(B) 9:1
(C) 6:1
(D) 12:1
11-In Otto cycle, addition of heat takes place at
(A) Constant pressure
(B) Constant volume
(C) Partially at constant pressure
(D) Any of the above
12-Which of the following is true for a two stroke engine?
(A) fuel efficiency is more than four stroke engine of same size
(B) higher fuel consumption
(C) used for two wheeler only
(D) eco friendly
13-Which type of nozzle can be used for facilitating pilot injection
before the main injection
(A) Single hole nozzle
(B) Multi hole nozzle
(C) Pintle nozzle
(D) Pintaux nozzle
14-At the venturi throat of the carburetor the velocity of air is
(A) Maximum
(B) Decreases
(C) Increases
(D) Remains same as before
15-The condition at which the engine operates at no load and with
nearly closed throttle is known as:
(A) Dieseling
(B) Cruising
(C) Idling
(D) None of the above
16-The reference fuels used for comparing the anti-knock value of SI
engine fuel is
(A) Benzene and tetraethyl lead
(B) Iso octane and normal heptane
(C) Normal cetane and alpha methyl naphthalene
(D) Benzene and iso octane
17-Releasing of clutch pedal causes
(A) load on release finger
(B) the compression of pressure spring
(C) pressure plate moves away from the clutch plate
(D) pressure plate moves towards clutch disc
18-Clutch shaft is also known as
(A) Transmission input shaft
(B) Counter shaft
(C) Lay shaft
(D) Main shaft
19-Throw out bearing is used to
(A) reduce friction on clutch disc
(B) engage the clutch
(C) disengage the clutch
(D) none of the above
20-Which of the following is not a function of final drive of heavy
vehicle?
(A) final speed reduction
(B) power transmission
(C) reduction of torque
(D) none of the above
21-Which of the following is not an advantage of overdrive?
(A) Fuel economy
(B) Increase of torque
(C) Reduced engine wear
(D) High vehicle speed at low engine speed
22-Idler gear is used to engage
(A) First gear
(B) Synchronizer ring
(C) Reverse gear
(D) Top gear
23-The tendency of front wheel drive cars with unequal length of half
shaft to pull to one side during acceleration is known as
(A) Torque steer
(B) Self steer
(C) Power steer
(D) None of the above
24-In Macpherson type suspension system shock absorber is mounted
on
(A) Lower wishbone
(B) Upper wishbone
(C) Strut
(D) Spring
25-Torsion bar is attached to
(A) Lower arm
(B) Upper arm
(C) Shock absorber
(D) Steering knuckle
 Total Questions Attempted

25
D

C
A

A
C

C
A

SUBMIT
SUBMIT
A

B
C
D
Trainer Name :
ID Number :
Email ID :
Location :
Total QuestionsAttempted :

Total Marks Obtained :

0
0
0
0

25
50

EXIT
EXIT
 TOTAL MARKS
D D 2 50
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
B B 2
0 0
0 0
0 0
0 0
B B 2
0 0
0 0
0 0
0 0
D D 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
D D 2
0 0
0 0
0 0
0 0
A A 2
0 0
 0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
B B 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0
C C 2
0 0
0 0
0 0
0 0
A A 2
0 0
0 0
0 0
0 0