Remote monitoring options for ABB drives, converters and inverters

User’s manual
NETA-21 remote monitoring tool
 User’s manual
NETA-21 remote monitoring tool

Table of contents

1. Safety

4. Mechanical installation

5. Electrical installation

6. Start-up

 2013 ABB Oy. All Rights Reserved. 3AUA0000096939 Rev C

EN
EFFECTIVE: 2013-07-12
 5

Table of contents

1. Safety
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Use of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety in installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2. Introduction to the manual

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Target audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Purpose of the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Terms and abbreviations used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3. Overview
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NETA-21 remote monitoring tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
NETA-21-specific features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Layout of the NETA-21 and the NEXA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Hardware and software requirements of the PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4. Mechanical installation
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Unpacking and examining the delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installing NEXA-21 to NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5. Electrical installation
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
General cabling instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Power connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Communication connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Data link connections –
Drive with the ACS-AP-x panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Data link connections –
Drive with the RDCU control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connection over the Ethernet tool network with an Ethernet adapter module . . . . . . 26
Connection via the EIA-485 port with a Modbus/RTU adapter module . . . . . . . . . . . 27
Connecting the NETA-21 to the RS-485 network . . . . . . . . . . . . . . . . . . . . . . . . . 27
Switching on the bus termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6

6. Start-up
Contents of this chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
First access to the user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connecting a local PC to the NETA-21 in the DHCP server mode . . . . . . . . . . . . . . 30
Logging on to the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Changing the password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Adding users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Setting date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Setting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Setting the location of the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Defining the Ethernet network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Initializing the communication between the NETA-21 and drives online . . . . . . . . . . . . 35
Initializing the communication between the NETA-21 and
ACS800 drives (or other drives with the RDCU control unit) . . . . . . . . . . . . . . . . . . 35

7. Program features
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Modbus/TCP gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
HTTPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
HTTPS certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
TCP and UDP network services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
In-bound network services on the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Out-bound network services on the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

8. Front page
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Parts and components of the portal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
All devices portlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Version information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Application toolbar and navigation bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Status icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Content area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

9. Users
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
My details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
User management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Users tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
User properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
User roles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FTP user account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Guest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Drive expert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Network admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Tool admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
User interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
 7

10. Devices
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Devices tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Device front page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Device control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Parameter browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Parameter properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Export of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Import of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Device data logger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Data logger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Opening a data logger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Setting up a data logger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Device interface settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Device interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Ethernet tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Modbus tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
DDCS tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Panel bus tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Interface settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
ETH settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Modbus settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
DDCS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Panel bus settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

11. Networks
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Network interfaces view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Test interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Ethernet panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Network status panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Network services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Test SMTP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Services panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Services settings panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Mail servers (outgoing) panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
HTTP/HTTPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Starting up the SMTP configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Using the Dynamic DNS service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Dial-up function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Using a mobile broadband connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

12. Events
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Universal event list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Contents of the non-universal event list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Filtering settings by columns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Filtering settings through the Event filter panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
8

13. Reporting
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Introduction to reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Configuring the NETA-21 for reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Creating an email report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Format of the email report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Creating an SD card report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Format of an SD card report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Creating an FTP report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Format of an FTP report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Setting the report trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Setting the reported data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Changing the reporting name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Changing the default naming of signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Log interval templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Using scripting for email reports (custom report) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Description of the tabs under Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Settings tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Devices tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Parameter history logging tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Reported data tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Configuration events tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

14. Tools
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Tool firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Factory tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Using ABB IP Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

15. Backup and restore

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Backing up the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Restoring the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

16. Memory card

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Using the memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Memory card status tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
File browser tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Autoinst tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Backup tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Report tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Restore tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

17. Diagnostics and troubleshooting

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
LED indications of the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
 9

LED indications of the NEXA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

18. Technical data

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Enclosure of the NETA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Enclosure of the NETA-21 with the NEXA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Technical data of the NETA-21 and the NEXA-21 . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Further information
Product and service inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Product training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Providing feedback on ABB Drives manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Document library on the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
10
 Safety 11

1
Safety

What this chapter contains

The chapter contains the warning symbols used in this manual and the safety instructions
which you must obey when you install or connect an optional module to a drive, converter
or inverter. If you ignore the safety instructions, injury, death or damage can occur. Read
this chapter before you start the installation.

Use of warnings
Warnings tell you about conditions which can cause injury or death, or damage to the
equipment. They also tell you how to prevent the danger. The manual uses these warning
symbols:

Electricity warning tells you about hazards from electricity which can cause
injury or death, or damage to the equipment.

General warning tells you about conditions, other than those caused by
electricity, which can cause injury or death, or damage to the equipment.
12 Safety

Safety in installation
These warnings are intended for all who install or connect an optional module to a drive,
converter or inverter, and need to open its front cover or door to perform the work.

WARNING! Obey these instructions. If you ignore them, injury or death, or

damage to the equipment can occur.

• If you are not a qualified electrician, do not do installation or maintenance work.

• Disconnect the drive, converter or inverter from all possible power sources. After you
have disconnected the drive, converter or inverter, always wait for 5 minutes to let the
intermediate circuit capacitors discharge before you continue.
• Disconnect all dangerous voltages connected to any control signal connectors in
reach. For example, it is possible that 230 V AC is connected from outside to a relay
output of the drive, converter or inverter.
• Always use a multimeter to make sure that there are no parts under voltage in reach.
The impedance of the multimeter must be at least 1 Mohm.
 Introduction to the manual 13

2
Introduction to the manual

What this chapter contains

This chapter introduces this manual.

Applicability
This manual applies to the NETA-21 remote monitoring tool and the NEXA-21 extension
unit for DDCS, SW version 2.14 or later.

Compatibility
The NETA-21 remote monitoring tool is compatible with various types of ABB drives, wind
turbine converters and solar inverters.
Note: Later in this manual, term drive substitutes for string drive/converter/inverter.

Target audience
The reader is expected to have basic knowledge of electrical fundamentals, electrical
wiring practices and how to operate the drive.

Purpose of the manual

The manual provides information on installing, commissioning and using the NETA-21.
14 Introduction to the manual

Before you start

It is assumed that the drive is installed and ready to operate before starting the installation
of the NETA-21.
In addition to conventional installation tools, have the drive manuals available during the
installation as they contain important information not included in this manual.

Contents
The manual consists of the following chapters:
• Safety presents the safety instructions which you must follow when installing a NETA-
21.
• Introduction to the manual introduces this manual.
• Overview contains a short description of the NETA-21.
• Mechanical installation contains a delivery checklist and instructions on installing the
NETA-21.
• Electrical installation contains the cabling and connection instructions of the NETA-21.
• Start-up contains instructions on how to start up the NETA-21.
• Program features contains feature descriptions in more detail.
• Users describes the user management.
• Devices describes how to manage device parameters and use data loggers.
• Networks explains how to set up and configure Ethernet network interfaces of the
NETA-21.
• Events describes how to observe and filter events.
• Reporting describes how to make reporting and trend logging settings for configuring
which time levels and event categories are sent out by a reporting plug-in to be
monitored.
• Tools explains how to manage NETA-21 firmware, factory settings and software
packages.
• Backup and restore describes the backup and restore functions of the NETA-21.
• Memory card describes the tabs under Memory card.
• Diagnostics and troubleshooting explains how to trace faults with the status LEDs on
the NETA-21 and the NEXA-21.
• Technical data contains the technical data of the NETA-21 and the NEXA-21.
 Introduction to the manual 15

Terms and abbreviations used in this manual

 Terms
Term Explanation

Assistant control panel Assistant control panel with an USB connector enabling a PC tool connection
for common architecture drives. Assistant control panel is a generic name for
ACS-AP-I and ACS-AP-S panels.

Data log File produced by a data logger. Can be sent and stored as a report
attachment.

Data logger Data logger inside a monitored device

Device Device connected to the NETA-21 for remote monitoring and data access. In
the UI devices are classified as generic devices, drives, converters or
inverters. See Device type.

Device interface Software component that enables access to certain types of devices

Device type Attribute for a device that is auto-detected or set by the user. Defines the
main category of the device, eg, if the device represents a rotating machine
or if it just converts electrical power from one form to another.

Drive Term drive is used instead of string drive/converter/inverter

Modbus/TCP gateway Modbus/TCP server that relays data read requests to any device interface.
Feature allows an external Modbus/TCP client (supporting protocol
specification v1.1b) to read data through the NETA-21 from any connected
device.

NETA-21 remote Hardware product for accessing drives remotely – typically off-site access
monitoring tool over public Internet, local/private Ethernet or modem connection.

Network interface Any defined interface to the connected data network

Network service Any inbound or outbound data connection provider in the NETA-21. NTP
time service and email (SMTP) are examples of outbound network services.

Parameter Operating instruction for the drive. Parameters are typically adjusted with a
control panel or a PC tool. Parameter browsing, monitoring and writing can
be done also with the NETA-21.

PC tool autodiscovery Network service which allows automatic detection of other Ethernet-based
ABB products (eg, the FENA-11) in a local network. In addition, enables
finding the NETA-21 in the network where the PC tool has been connected.

Portlet Panel for text and controls within a page or tab. Some portlets can be moved
around, added and removed, eg, on the front page.

Trend logging = parameter Refers to low time resolution, long-term data logging performed by the
history logging NETA-21. Trend logging is a functionality within the NETA-21 while data
loggers are part of the drive functionality and merely configured with the
NETA-21.

User account A user name that in combination with a password can be used to access the
NETA-21 web user interface or some other services of the NETA-21.

Web UI Web-based user interface of the NETA-21

16 Introduction to the manual

 Abbreviations
Abbreviation Explanation

DDCS Distributed Drives Communication System, an optical fiber device access

method for drives and inverters (for example, ACS800 and PVS800)

DDNS Dynamic Domain Name System

DHCP Dynamic Host Configuration Protocol, a protocol for configuring servers in a

network

FTP File Transfer Protocol provides an unsecure way to access files in a network

FTPS File Transfer Protocol Secure provides a secure way to access files in a net-
work

HTTP Hypertext Transfer Protocol is an application protocol used between data cli-
ents and web servers

HTTPS Hypertext Transfer Protocol Secure is a combination of the HTTP and

SSL/TLS protocols. Provides secure communication with web servers.

NBT NS NBT NS is a daemon for the NetBIOS name discovery. Allows finding com-
puters from a local network by using the NetBIOS host name.

NTP Network Time Protocol is a protocol for synchronizing computer clocks over
a network

SMTP Simple Mail Transfer Protocol is a protocol for sending emails

SSH Secure Shell, a protocol for a secure remote access.

SSL/TLS Transport Layer Security (previously Secure Sockets Layer) protocol is used
to encrypt data between clients and servers

TCP Transmission Control Protocol, used together with Internet Protocol (IP) as
the transport protocol for the Internet

UI User interface

UTC Coordinated Universal Time is the most often used time in the world. Time
zones are presented with positive or negative offsets.
 Overview 17

3
Overview

What this chapter contains

This chapter contains a short description of the NETA-21.

NETA-21 remote monitoring tool

The NETA-21 remote monitoring tool is used for browser-based remote monitoring of ABB
drives via Ethernet. Multiple drives can be connected to the network by using a panel bus
or through the fiber optic channel of the NEXA-21 extension unit.
Through the NETA-21, you can:
• monitor drives
• read and adjust drive parameter values
• read status information and actual values from drives
• set up and monitor the data logger and save its content to a file
• read the contents of the fault log from monitored devices and save it to the memory
• send email messages on events
• use email for continuous monitoring of drives
• reset a fault on drives
• use an SD card for continuous monitoring of drives
• use an SD card to store all events
• use the FTP server for storing drive parameters and events
• create custom events
• create custom reports: email reports, SD card reports and FTP reports.
18 Overview

The NETA-21 is not intended for controlling or commissioning the drive. The NETA-21
provides stand-alone logging without a PC and automated data reporting to external data
systems. The user interface can be accessed with any web browser including mobile
devices, without the need to install any special software.

NETA-21-specific features
• two network connections
• Internal (factory line)
• external (Internet access)
• automatic or fixed IP configuration
• easy point-to-point access to the NETA-21 with a PC (no need to change the IP
address of the PC)
• email reporting of events and parameter history logs
• FTP reporting of events and parameter history logs to an external FTP server
• storing of events and history log files to a SD memory card
• FTP and FTPS file access to an SD/SDHC memory card
• browsing an SD/SDHC memory card via the web UI
• different access rights for different users
• NETA-21 software upgrade locally or remotely
• importation of the NETA-21 settings from the USB memory
• time synchronization via an NTP server
• full or selected backup/restore of the software
• Dynamic DNS support
• support devices connected via:
• panel bus (ACSx80 series)
• Ethernet PC tool communication (ACSx80 series)
• DDCS with a fiber optic cable (eg, ACS800, ACS600)
• Modbus/RTU via RS485
• support for a USB modem
• online monitoring with a history
• automatic discovery the connected device
• automatic log changes in the connected device.
 Overview 19

 Layout of the NETA-21 and the NEXA-21

The following figures describe the front and bottom layout of the NETA-21 and the NEXA-
21.
NETA-21 NETA-21 and NEXA-21

4 4

5
3

11

5
8

7 10
6a

6b 12

9 13

1 Front panel labelled with a black sticker and equipped with indicator LEDs

2 PWR, STAT, MON – power, status and monitoring indicators, see LED indications

3 SD – SD/SDHC memory card slot

4 USB – USB host connector for third party extensions

5 PNL 1/PNL 2 – connector providing an interface for a panel bus that can be used for communication
with certain drive types

6a PC ETH 1 – connector providing an Ethernet connection for a locally connected PC

6b ETH 2 – connector providing an Ethernet connection for an external Ethernet network

7 Connector for the NEXA-21 unit

8 SD RJ45 – SD button is used for removing the SD/SDHC card safely and activating a DHCP server
for the first access to the user interface

9 Reset button is used for rebooting the NETA-21

10 NEXA-21 provides a DDCS fiber optics connection, secondary power input and one extra USB
connector

11 PWR, STAT, RX, TX – power, status and RX/TX indicators, see LED indications

12 Fiber optic transmitter DDCS

13 Fiber optic receiver DDCS

20 Overview

NETA-21 NETA-21 and NEXA-21

1
5

1 X1 10…30 V DC – power supply input

2 X2 EIA-232 connector for a modem

3 X3 EIA-485 connector for a Modbus network

4 Termination jumpers for the link connected to X3

5 X11 AC/DC 24V – secondary power supply input

Hardware and software requirements of the PC

The NETA-21 can be configured and used with a normal PC with:
• Ethernet network adapter
• Windows XP/Vista/7/8, Linux, MAC OS
• Internet Explorer 7+, Firefox 3.6+ (PC, Mac), Safari 5+, Chrome 10+ or Opera 11+
(PC, Mac).
Most mobile phone and tablet browsers are also capable of showing the NETA-21 web
pages, but displayed elements are not fully optimized for the touch screen use.
Javascript and cookies must be enabled in the web browser settings before you can use
the NETA-21 web interface. The NETA-21 does not require external plug-ins, such as Java
or Flash.
 Mechanical installation 21

4
Mechanical installation

What this chapter contains

This chapter contains a delivery checklist and instructions on mounting the NETA-21.

WARNING! Follow the safety instructions given in this manual and the drive
documentation.

Unpacking and examining the delivery

The option package for the NETA-21 contains:
• remote monitoring tool, type NETA-21
• NETA-21 remote monitoring tool installation and start-up guide (3AUA0000096881
[English]).
The option package for the NEXA-21 contains:
• extension unit, type NEXA-21
• NEXA-21 installation instructions sheet.
1. Open the option package.
2. Make sure the package contains all items listed above.
3. Make sure that there are no signs of damage.
22 Mechanical installation

Installing NEXA-21 to NETA-21

4. Press the NEXA-21 against the NETA-21.
5. Tighten the grounding screw.
Do not use excessive force.

Installing the NETA-21

1. Protect the devices from the drilling dust.
2. Drill the holes for the fastening screws of the mounting rail.
3. Fasten the mounting rail.

4. Snap the NETA-21 onto the rail.

DIN rail grounding clip

See the grounding instructions in section Grounding.

 Electrical installation 23

5
Electrical installation

What this chapter contains

This chapter contains:
• general cabling instructions
• grounding instructions
• instructions on setting the IP address
• instructions on connecting the NETA-21 to the drive and to the Ethernet network.

WARNING! Only qualified electricians are allowed to carry out the work described
in this chapter. Follow the instructions in section Safety in installation. Ignoring the
safety instructions can cause physical injury or death.

General cabling instructions

• Arrange the cables as far away from the power cables as possible.
• Avoid parallel runs with the power cables.
See chapter Technical data for information on cable types.
24 Electrical installation

Grounding
The ground of the NETA-21 is connected to the mounting rail by means of an grounding
clip. The mounting rail must be grounded to a noiseless ground. If the rail is not mounted
on a properly grounded base, a separate grounding conductor must be used. The
conductor must be as short as possible and its cross-sectional area must be 6 mm2 at
least.
Note: No solid copper conductor may be used (stranded wire allowed only).

Power connections
Connect the power supply to connector X1 of the NETA-21. The NETA-21 supplies also
the NEXA-21. For information on the connector type, voltage and power specification, see
Technical data of the NETA-21 and the NEXA-21.
Note: In the NEXA-21, there is an alternative power supply input (X11), which you can use
for supplying power to the NEXA-21 and the NETA-21.

Communication connections
 Data link connections –
Drive with the ACS-AP-x panel
Termination switch of Termination switch of
the bus the bus
NETA-21

PNL1

PNL2

PC
ETH1

ETH2
ABB drive, ABB drive, ABB drive, ABB drive,
converter or converter or converter or converter or
inverter inverter inverter inverter

PC Link to Ethernet networks

Note: The RJ45 connectors of the control panel are located in the “ceiling” of the control panel housing.
Beside the left-hand side RJ45 connector in the control panel housing there is a switch that must be pushed
upwards in the last drive of the chain to terminate the bus.

The maximum number of devices per panel port bus is 32.

Set a unique ID to each node on the panel bus. See the appropriate drive manual.
 Electrical installation 25

 Data link connections –

Drive with the RDCU control unit
The figures below show the data connections in a ring and star topology when a fiber optic
link is used.
ABB drive, ABB drive, ABB drive,
converter or converter or converter or
inverter inverter inverter

NETA-21

NEXA-21
RDCU RDCU RDCU

RDCO RDCO RDCO

T R TT R T
T R

PC
ETH1

Tx

ETH2
Rx

PC
Link to Ethernet networks

The maximum number of devices per fiber optic link is 10.

Connect the NEXA-21 primarily to fiber optic channel ch3 on the RDCO connector unit.
You can connect the NEXA-21 also to ch0 if the maximum speed of the DDCS
communication does not increase above 1 Mbit/s.
The default NETA-21 settings for a DDCS network are ring topology and 1 Mbit/s
communication speed. With these settings, the NETA-21 can normally auto-detect drives
connected to an NDBU branching unit. The NETA-21 auto-detects connected devices
when the fiber is connected for the first time. If reconfiguration is needed afterwards, it can
be done in the web user interface.
26 Electrical installation

Note: Use the same speed setting in the NETA-21, NDBU branching unit and drives.
ABB drive, ABB drive,
converter or converter or
inverter inverter

RDCU RDCU

RDCO RDCO
NETA-21 NDBU-x5
NEXA-21

T R T R

V106
PC CH1
V105
ETH1
V104
CH0
V103
Tx
V102
MSTR
ETH2 V101
Rx

Drive/converter/inverter 1 to CH0 … drive/converter/inverter 9 to CH8

Link to Ethernet networks

PC

 Connection over the Ethernet tool network with an Ethernet adapter

module
In the Ethernet tool network, each drive/unit is connected to the network through a FENA-
11/21 Ethernet adapter module.
NETA-21 ABB drive ABB drive ABB drive
or unit or unit or unit
with the with the with the
FENA-11/21 FENA-11/21 FENA-11/21

PC
ETH1

ETH2

Ethernet switch

The NETA-21 detects nearby adapter modules (max. 10 pcs) in a local network. The
automatic detection is enabled by default only via the ETH2 port. To change the settings of
 Electrical installation 27

the automatic detection, go to Settings –> Device interfaces –> Ethernet –>
Settings –> Background scan.
Note: If the ETH1 and ETH2 ports of the NETA-21 are connected, they must be configured
to use different sub-nets (different IP addresses under non-overlapping netmasks).

 Connection via the EIA-485 port with a Modbus/RTU adapter

module
A maximum of 32 monitored Modbus/RTU devices can be connected to the same EIA-485
network. The following figure is an example of an allowable topology:
NETA-21 ABB drive with Other slave ABB drive with
an FSCA-01 device an FSCA-01
or with an or with an
embedded embedded
EIA-485 port EIA-485 port

Other slave ABB drive with Other slave ABB drive with
device an FSCA-01 device an FSCA-01
or with an or with an
embedded embedded
EIA-485 port EIA-485 port

T = Termination

The X3 EIA-485 connector for a Modbus network is located at the bottom of the NETA-21.
See the bottom layout in section Layout of the NETA-21 and the NEXA-21. The EIA-485
(RS-485) cabling requires a shielded dual twisted pair cable. The nominal impedance of
the cable must between 100…150 ohm.

Connecting the NETA-21 to the RS-485 network

Connect the bus cable to connector X3 on the NETA-21.
The pin allocation of the X3 connector is shown below.
1 2 3 4

X1 Description
1 SHLD Bus cable shield. Connected internally to a ground clip via an RC filter. Depending on
the installation environment, the shielding is connected to this pin on the NETA-21 or
on another location on the EIA-485 network.
2 DATA_B Data positive
3 DATA_A Data negative
4 GND_B Isolated signal ground

Signals DATA_A, DATA_B and GND_B must always be connected to all communication
modules and to the NETA-21.
28 Electrical installation

Switching on the bus termination

To avoid signal reflection, add 120-ohm termination to the last devices at each end of the
bus line.
J2 J2 J2 J2

Termination Termination Termination Termination

activated deactivated deactivated activated

EIA-485 device EIA-485 device EIA-485 device EIA-485 device

Term. Term. Term. Term.

ON OFF OFF ON

You can use the internal resistor of RS-485/EIA-485 adapters or an external passive
termination resistor. The internal termination switch activates also the pull-up and pull-
down resistors.
 Start-up 29

6
Start-up

Contents of this chapter

This chapter tells you how to start the NETA-21.

First access to the user interface

This section tells you how to get access to the user interface. The NETA-21 can be used
as a DHCP server for a local PC when the PC is connected to the PC ETH 1 terminal.
When the DHCP server mode is activated, the NETA-21 provides an IP address to the PC
for an easy connection.
The NETA-21 uses dynamic IP addressing by default. After it starts, the NETA-21 tries to
get a dynamic IP address from the local Ethernet network if there is a DHCP server
available. If there is no local DHCP server in the connected network, then the NETA-21
assigns itself a Zero Configuration networking address in the range of
169.254.1.0…169.254.254.255. The technology of the automatic IP address configuration
is called either Link-local address assignment (RFC 3927) or Automatic Private IP
addressing (APIPA).
When a local PC is connected to the PC ETH 1 connector, you can set the NETA-21 as the
DHCP server in the Ethernet 1 link.
30 Start-up

 Connecting a local PC to the NETA-21 in the DHCP server mode

Note: If another device operates in the DHCP server mode, you cannot use the NETA-21
the DHCP mode in the local Ethernet 1 network.
1. Start the NETA-21.
2. Wait until the set-up completes and the STAT LED is green.
3. Push the SD RJ45 button for 5 seconds or until the PC ETH 1 LED starts to flash
green.
The NETA-21 operates as a DHCP server via the PC ETH 1 connector.
4. Connect the PC to the PC ETH 1 connector.
The PC gets a dynamic IP from the NETA-21.
The PC ETH 1 LED shows that there is a connection (green blink = waiting, green =
connected).
Note: If after one minute there is no connection between the PC and the NETA-21, the
DHCP server mode in the NETA-21 is set off.
5. Go to http://192.168.230.1.
Note: If the Ethernet cable is connected to the NETA-21 before you push the SD RJ45
button, the PC does not automatically get an IP address.

 Logging on to the NETA-21

1. With the web browser of you PC, navigate to http://192.168.230.1.
2. When you log on to the NETA-21 for the first time, use the default user
name/password.
Type “admin” both to the Username and Password text boxes
The UI recommends that you use the secure HTTPS login. If you click the link, you get
a notification on a possible warning message concerning an invalid certificate.

3. Click Login.
You are redirected to the front page.
 Start-up 31

If the authentication does not succeed and you are redirected back to the Login dialog
box, the following error messages may appear:
• Authentication failed. Contact system administrator for more information.
• You have logged out from the remote monitoring tool!
• Session expired; you were automatically logged out because of idle time was
exceeded.
• Server (remote tool) does not respond to authorization request.
• The server was rebooted.
By clicking the Information... button you can get information on, eg, the serial number
and MAC addresses of the Ethernet interfaces. To customize the data, go to Settings
–> User interface.
4. Change the password (recommended).

You can keep the default password by clicking the Don’t change button.
Note: It is highly recommended to change the default password when you log on to
the NETA-21 for the first time.
The front page of the user interface is shown. See chapter Front page.
You are now logged on as a tool administrator (Tool admin). See section User roles.

Basic settings
 Changing the password
1. To change your password, go to Settings –> My details –> Change password.

2. Type the old password to the Old password text box.

3. Type the new password to the New password text box.
4. Type the new password again to the Confirm new password text box.
5. Click Save.
32 Start-up

 Adding users
Note: You can add users only if you have the access rights of Network admin or Tool
admin.
1. To add a user, go to Settings –> Users –> Add user.
The User properties panel appears on the right-hand side of the tab.

The components of the tab are described in section User management.

2. Fill in the text boxes.
The name typed into the Full name text box is shown in the upper right-hand side
corner of the window. The user name (login name) is created under the User &
password sub-panel in step 4.
3. Expand the User & password sub-panel by clicking the heading.
4. Fill in the text boxes.
See section User roles.
5. Click Create user.
 Start-up 33

 Setting date and time

Note: To change the locale settings, you must have the access rights of Drive expert,
Network admin or Tool admin.
1. To set date and time, go to Settings –> Locale –> Date and time.
Note: If the NETA-21 does not have the correct date and time, the stored data will also
be logged with incorrect date and time stamp.

2. In the Time source drop-down list, select one of the following values:
• Automatic
• NTP (Network Time Protocol)
• Manual.
If you select Manual, you have to define the time from the Current time drop-down list
and select the date from the calendar in the Current date box.
Note: In the Automatic mode the NETA-21 tries to fetch time and date over NTP,
contacting server pool.ntp.org by default.
3. Fill in other appropriate boxes.

 Setting the language

Note: To change the locale settings, you must have the access rights of Drive expert,
Network admin or Tool admin.
To set the language and to localize the data formats of the NETA-21, go to Settings –>
Locale –> Language.

Note: The language selected on the Language tab is used only in the web UI of the
NETA-21. Monitored devices can have their own independent language selectors.
34 Start-up

 Setting the location of the NETA-21

Note: To change the locale settings, you must have the access rights of Drive expert,
Network admin or Tool admin.
To set the location of the NETA-21, go to Settings –> Locale –> Location.

 Defining the Ethernet network settings

1. Go to Settings –> Network interface and enable the Obtain DNS server
automatically function.
The NETA-21 adjusts the communication settings automatically. Individual attributes
can be set separately.
Enable the function both for local Ethernet 1 connected to the PC ETH 1 connector
and external Ethernet 2 connected to the ETH 2 connector.
Note: From firmware version 2.12 onwards, the Ethernet settings are taken into use
directly after the settings have been saved. The NETA-21 shows a warning explaining
that connection can be lost if the IP address of the currently active connection is
changed.
2. Check the LAN settings of your PC.
Activate the following functions: Obtain an IP address automatically and Obtain
DNS server address automatically.
 Start-up 35

Initializing the communication between the NETA-21 and

drives online

WARNING! Follow the instructions in section Safety in installation.

 Initializing the communication between the NETA-21 and

ACS800 drives (or other drives with the RDCU control unit)
1. Switch the drives on.
2. In the first drive, change the node address of channel 3 (CH3) to 1 (example: ACS800
standard control 70.02 CHANNEL 3 ADDR = 1).
3. In the second drive, change the node address of channel 3 (CH3) to 2 (example:
ACS800 standards control 70.02 CHANNEL 3 ADDR = 2).
4. Give the rest of the drives a unique ID as well.
See the appropriate drive manuals.
5. Switch the drives off to set the channel address settings.
6. Switch the NETA-21 off or disconnect the fibre optic cable from the NEXA-21 for more
than 1 minute.
7. Connect the drives to the NEXA-21. See section Communication connections. Use
either the ring or star topology.
8. Switch the drives, NETA-21 and NEXA-21 on.
9. Wait until the PWR and STAT LEDs of the NEXA-21 go green.
Tx and Rx LEDs are yellow indicating that there is data transmission between the
NETA-21 and monitored devices.
10. Log on to the UI when the STAT LED of the NEXA-21 is blinking green.
The UI recognizes the monitored device automatically and the drive is shown in the
user interface.

Note: If the NETA-21 does not detect all drives automatically, go to Settings –>
Device interfaces –> ddcs –> Rescan devices.
11. Click Save.
36 Start-up
 Program features 37

7
Program features

What this chapter contains

This chapter describes some of the features listed in section NETA-21-specific features in
more detail.

Modbus/TCP gateway
The NETA-21 supports the Modbus/TCP protocol that allows to use a normal TCP/IP
connection to access the parameters of drives.
With a normal PC and a program that supports the Modbus/TCP protocol in the same
network to which the NETA-21 is connected, you can query values of parameters from the
connected devices. You cannot write to parameters through Modbus/TCP. The
Modbus/TCP client configuration requires you only to specify the IP of the NETA-21 and
port 502.
The Modbus protocol supports up to 247 devices. Each device is identified with an ID, a
number from 1 to 247.
ID range Protocol

1…32 DDCS fiber optics

33…64 Panel bus 1 (port PNL1)

65…96 Panel bus 2 (port PNL2)

97…128 Modbus/RTU

129…160 Ethernet tool network

161…247 Reserved
38 Program features

The ID used by a specific device can be determined with its internal name (shown in the
Device parameters panel under Device interfaces). This name always ends with a
number that represents the index inside the range of the IDs of the specific protocol. For
example, a slave device connected through the Modbus/RTU protocol with station address
3 (device node ID mb_3) is accessible by Modbus/TCP gateway station address 99 (97+3-
1).
To access a specific parameter of a given group and index, you must specify an address
by calculating it according to one of the following formulas:
16-bit address = (4)0000 + 100 × group + index
32-bit address = (4)20000 + 200 x group + 2 x index

Device
Modbus
PC
mb_3 Modbus device, parameter 01.15
ID: 99
Address: 115
NETA-21 Switch Panel bus (port PNL2) device ID 1,
parameter 03.10 using 32-bit addressing
Device ID: 65
Address: 420000 + 200 x 3 + 2 x 10 =
Panel bus {2} {1} 420620
pnl2_01

By default, the Modbus protocol returns the internal raw 16-bit value and does not specify
any information about sign and scaling. Therefore, you must apply the correct ones for the
specified parameter.
Note: Most Modbus/TCP master applications omit the 40000 (or 400000) from the
beginning of the register numbering.
The Modbus function code 03 Read Holding Registers is supported over the Modbus/TCP
gateway of the NETA-21.

HTTP
The HTTP (Hypertext Transfer Protocol) is used to serve web pages using the HTML
(Hypertext Markup Language) and Javascript. To use the NETA-21 web interface you
need a browser supporting Javascript and cookies (see Hardware and software
requirements of the PC). External plug-ins, such as Java or Flash, are not required.
It is recommended to use HTTP only with a direct cable connection to the NETA-21. For all
other purposes it is recommended to use the secure HTTPS. To switch from HTTP to
HTTPS edit the address from http://192.168.230.1 to https://192.168.230.1. You can also
do this by checking the Prefer HTTPS check box in Network services.
HTTPS URLs use port 443 by default, whereas HTTP URLs use port 80 by default.
 Program features 39

HTTPS
The Hypertext Transfer Protocol Secure (HTTPS) is a combination of the HTTP with an
added encryption layer of SSL/TLS protocols to create a secure channel over an insecure
network, provided that adequate cipher suites are used and that the server certificate is
verified and trusted. The HTTPS is supported by all popular browsers.
Note: Although the HTTPS encrypts everything, including the URL, an eavesdropper can
still observe the host name and port of the URL because they are part of TCP/IP packets
to establish and maintain the connection. This means that an eavesdropper or attacker
can know that a connection is taking place between the two parties, get the domain name
and IP addresses, through which he can see the sites the host is connect to, the amount of
time spend using a site, and the amount of information uploaded or downloaded on the
particular site.

 HTTPS certificate
The NETA-21 HTTPS uses a self-signed certificate which is uniquely generated per each
NETA-21 tool. The factory reset of the NETA-21 can also reset the self-signed certificate
and generate a new one (while, eg, a firmware update keeps the certificate unchanged).
Most browsers display a warning if they receive an invalid or a self-signed certificate.
When you connect an older browser to a site with an invalid certificate the browser shows
you a dialog box asking if you want to continue. Newer browsers display a warning across
the entire window and also prominently display the site's security information in the
address bar. Extended validation certificates turn the address bar green in newer
browsers. Most browsers also display a warning when you visit a site that contains a
mixture of encrypted and unencrypted content.
From the NETA-21 firmware version 2.13 onwards you can install a customized HTTPS
site certificate to each NETA-21. The installation requires than an Apache 2 compatible
apache.pem certificate file is generated on the PC and saved to folder "cert” in the SD
memory card. The customized certificate will be taken to use after a reboot or power-up of
the NETA-21. A valid certificate is taken into use and removed from the memory card for
security reasons.
40 Program features

TCP and UDP network services

There are multiple in-bound and out-bound network services running on the NETA-21.

 In-bound network services on the NETA-21

Port Service Purpose

21 / TCP FTP File transfer service. Enabled by default, but FTP user accounts need to be
990 / TCP specified in the web UI (Settings –> Users) before the FTP login becomes
possible.
Port 990 provides a file transfer service with an SSL security layer. You can
use the same user accounts as for the FTP service. Explicit TLS encryption
must be used in a FTPS client. (SFTP protocol is not supported).
To modify the FTP and FTPS service availability, go to
Settings –> Network services.

22 / TCP SSH SSH console for support and diagnostics. Each NETA-21 contains a factory
user account with a random password. SSH access is not provided for
NETA-21 end users. To disable the SSH service, go to Settings –> Tool
settings –> Factory tools and unselect Enable factory login (factory
support account).

80 / TCP HTTP Web server provides the UI over the HTTP protocol. HTTP protocol access
is always enabled. Recommendation to use HTTPS is shown in the tool
login box.

443 / TCP HTTPS Secure version of the HTTP pages. To modify the HTTPS port, go to Set-
tings –> Network services.

502 / TCP Modbus/TCP Modbus/TCP Gateway is listening on port 502. Gateway forwards Mod-
bus/TCP data read requests to any connected drive (either as DDCS fibre
optics, RJ45 Panel bus or as EIA485 Modbus/RTU traffic). To modify the
service availability, go to Settings –> Network services.

(optional) / HTTP To specify an extra HTTP port (any higher TCP port than 1024) or a default
TCP HTTPs port, go to Settings –> Network services. Extra port is disabled by
default.

67,68 / UDP DHCP DHCP client functionality is used in both Ethernet ports by default as speci-
(client and fied in RFC 3927 (Dynamic Configuration of IPv4 Link-Local Addresses).
server) DHCP server can be activated only on the ETH1 port.

137 / UDP NBT NS Netbios (NBT) Name Service allows a name resolution from Windows XP /
Windows 7 PC by typing http://neta-21 to the address bar of the web
browser (if a firewall is disabled in Windows).
NBT NS service is active only on the ETH1 port by default. To modify the
service availability, go to Settings –> Network services.

24576 / ABB Autodiscovery protocol used by ControlBuilder plus (IP Configuration tool)
UDP Netconfig and Drive composer pro and DriveWindow 2.40 PC tools to discover ABB-
specific Ethernet devices in a local network segment, by listening to and
responding to UDP broadcasts. This service is also in the out-bound ser-
vices list.

61332 / DDCS Ethernet gateway service is disabled by default. When enabled, DDCS
UDP Ethernet GW Ethernet gateway starts to wait for DriveWindow PC tool connections on
this port. To enable the service, go to Settings –> Device interfaces –>
DDCS –> Settings –> Ethernet GW.
 Program features 41

 Out-bound network services on the NETA-21

Port Service Purpose

21 FTP File Transfer Protocol. Reporting option for sending CSV files over the FTP
protocol to any external server. Not in use until configured.

25 / TCP SMTP(S) Simple Mail Transfer Protocol, outgoing e-mail. Also secure version
(or another SMTPS is supported (typically TCP port 587 or 465). NETA-21 can send
configured email out if the SMTP(S) server settings and email reporting are configured.
port) By default, the service is not in use.
Two SMTP servers are supported (primary and secondary server). Server
names and outgoing port numbers can be configured in the web UI (Set-
tings –> Network services). To enable the email plug-in, go to Reports –>
Settings –> Add and select E-mail reporting.

80, 443 HTTP, Used for reporting data to external portal services. Not in use until config-
HTTPS ured.

80 HTTP HTTP protocol is used for the Ethernet tool network slave device access, to
access FENA-11/-21 fieldbus modules and BCU-xx control boards over the
Ethernet tool network (typical use case in a local/private network only).
Connection to supported devices established if supported devices are dis-
covered.

123 / UDP NTP Network Time Service.

NETA-21 sends outgoing NTP service packets to “pool.ntp.org” by default
every hour. To configure the setting, go to Settings –> Locale –> Time. If
no NTP server is found, the NETA-21 defaults to a manually configured
clock setting.

24576 / ABB Autodiscovery protocol. By default the NETA-21 sends discovery broad-
UDP Netconfig casts over the ETH2 interface every minute to discover other ABB devices
(eg, FENA-11 or BCU-xx) in a local network segment. To modify the back-
ground scan setting, go to Settings –> Device interfaces –> Ethernet –>
Settings.
42 Program features
 Front page 43

8
Front page

What this chapter contains

This chapter describes the front page of the web UI.

Parts and components of the portal

The front page consists of the following parts:
• application-specific toolbar (1)
• navigation bar (2)
• content area (3).

2
3
44 Front page

The front page is a portal where you can change the contents by adding, removing or
moving around the portlets. The figure below shows a modified front page.

The front page contains the following components:

• Refresh button updates the contents of the front page.
• Add content button adds new portlets to the front page. The portlet can be selected
from a pop-up menu. If a portlet is already selected, the corresponding menu item is
disabled in the pop-up menu.

• Save layout button stores the current layout to be loaded when the front page is
opened again.
• Welcome instructions portlet contains instructions for the new user. To change the
instruction text, go to Settings –> User interface.
• Tool description portlet contains a description of the NETA-21. The description text
can be changed from the settings.
• Favorite parameters portlet contains the parameters that are marked with a blue star
on the Parameter browser tab. To refresh the values of the parameters, click the
Refresh button on the title bar.
 Front page 45

To group the parameters by drive, click the button on the title bar.
• Unconfigured settings portlet shows the settings categories that have not been
configured or that are misconfigured. By clicking the category button you are
redirected to the corresponding settings view.

All devices portlet

The All devices portlet shows all devices connected to the NETA-21. To navigate to the
front page of a device, double-click the device in the list.

All portlets can be minimized or closed by clicking the icons in the right corner of the portlet
title bar.

Version information
To find out the version information of the NETA-21, click About in the navigation bar of the
user interface or the corresponding icon in the application-specific toolbar.

• Features tab shows the versions of the internal software components.

• License tab contains the software license agreement.
• 3rd party licences tab lists the third-party software licenses in this product. The third-
party licenses include open source software licenses.
46 Front page

 Application toolbar and navigation bar

The application-specific toolbar is visible in every view (excluding the login page) on the
top of the user interface. The toolbar provides a quick access to the views that are used
most frequently. The toolbar contains the following components:
• Tool ID field shows the identifier of the NETA-21 (default: NETA-21 <serialno>).
• Time field shows the current time and time zone of the NETA-21.
• Location field shows the location of the NETA-21.
• User name field in the upper right hand corner shows the name of the user that has
logged on.
• Logout link logs the currently logged-on user out. The user is redirected to the login
page.
• Help button opens the following dialog box.
Note: The ABB library access requires a connection to the Internet.

• Home button opens the front page of the user.

• Reports button opens the reporting view.
• Settings button opens the main settings view.
• Devices button opens a view showing all the devices connected to the NETA-21.
• Top bar can be shrunk to a smaller size by clicking the double arrow button at the
bottom right corner of the grey box.

The navigation bar contains the above-mentioned navigational items and also the sub-
items for the Settings and Devices items.
 Front page 47

The navigation bar can be hidden/unhidden by clicking the small arrow between the
navigation bar and the content area or the double arrow within the Navigation title bar.

Status icons
In the navigation bar and application toolbar the statuses of the devices are indicated with
small icons. The following device statuses are supported:
disconnected
busy
warning
fault.
If the device is connected and functioning normally, the device is shown without any status
icon.
The Devices button in the application toolbar can have a maximum of three different
status icons simultaneously. For example, if there are two devices that are disconnected,
only one icon indicating a disconnected device is shown in the Devices button. If there is
one disconnected device and one busy device, both icons are shown in the Devices
button. If all four statuses occur at the same time, the icons indicating the fault,
disconnected and warning statuses are shown in the Devices button. If the status of the
device is missing or cannot be read, the device is shown with the busy icon.

 Content area
The application-specific tabs are shown in the content area. The view in the content area
changes as soon as you have selected another application since the UI does not have to
load a new HTML file from the server. However, you may have to refresh the view if the
data gets out of date.
48 Front page
 Users 49

9
Users

What this chapter contains

This chapter describes the user management.

My details
To see the settings of a current user, go to Settings –> My details. On the admin tab, you
can change your email address, phone number, language and password. You cannot
change your user name or role, even if you had an administrator role.
50 Users

The admin tab contains the following components:

• Save button saves the modified settings to the server.
• Reset button cancels the changes in the settings.
• Full name text box shows the full name of the current user.
• User name text box shows the user name of the current user.
• User role text box shows the user role of the current user.
• E-mail address text box shows the email address of the current user.
• Phone number text box shows the phone number of the current user.
• Language drop-down list shows the selected language of the user interface.
• When the language is changed, the change takes place in the user interfaces as
the next view is loaded from the server.
• Old password text box is empty by default.
• If you want to set a new password, the old password must be written for
verification purposes.
• New password text box empty by default.
• The minimum requirement for the valid password is two different characters.
• Confirm new password text box is empty by default.
• You are notified if both passwords do not match or the old password is wrong or
missing.

User management
You can restrict the access rights of users by choosing different roles for them. The names
of the roles are descriptive, for example, Guest has the lowest level access to the NETA-
21 and Tool admin can change everything in it.
You can fine-tune the user roles but you cannot create customized user roles.

 Users tab
On the Users tab you can add, remove and modify users.

The Users tab contains the following buttons:

• Add user button inserts a new user in the list with default settings. The new user is not
added to the UI until you have clicked the Create user button in the User properties
panel.
• Remove user button removes the selected user from the UI. This button is disabled if
no users are selected from the user list, or if the user selects itself.
 Users 51

User list contains all existing users, which can be sorted according to different columns.
When a user is selected from the list, the User properties panel appears on the right side
of the tab.

The user list contains the following columns:

• User name shows the name which is used for logging on to the UI.
• Full name shows the full name of the user.
• E-mail address shows the email address of the user.
• Phone number shows the phone number of the user.
• Language shows the used language when the user is logged on.

User properties
The User properties panel contains modifiable settings for the selected user. This panel is
visible only if a user is selected from the user list. The User properties panel consists of
two sub-panels: User details and User & password.
52 Users

The User details sub-panel inside the User properties panel contains the following
components:
• Full name text box defines the full name of the user. When you are creating a new
user, the user name in the User & password sub-panel is generated based on the full
name if you have not already modified the login name.
• User role drop-down list contains all the roles that can be selected for the user: See
User roles. Guest is selected by default. The user cannot change his/her own role.
• E-mail address text box defines the email address of the user (optional).
• Phone number text box defines the phone number of the user (optional).
• Language drop-down list contains all possible languages in the UI. This defines the
language used when the user logs on.
• Comment text box provides the administrators with an area for writing a comment on
the currently selected user. The comment is not visible for the selected user (unless
the user has administrator privileges).
The User & password sub-panel inside the User properties panel contains the
authentication details of the user:
• User name text box defines the name of the user.
• Password text box defines the password for the user name. The password is not
shown in plain text. The minimum length for a password is 2 symbols.
• Confirm Password text box is used for checking that the password has been typed
correctly. The password is not shown in plain text.

In the lower part of the User properties panel there are two buttons, whose names
change by the context. When you are creating a new user, there are the following buttons:
• Create user for saving the new user settings
• Cancel for cancelling the creation and removing new_user (default name) from list.
 Users 53

When you are modifying an existing user, there are the following buttons:
• Apply changes for saving the modifications
• Restore defaults for resetting the values to a previously saved user setting.
When the new user logs on to the UI for the first time, he/she is prompted to change the
password.

User roles
The user roles to be selected from the User role drop-down list on page 32 are the
following:
• Tool admin
• Network admin
• Drive expert
• User
• Guest
• FTP user account.

 FTP user account

The FTP user account does not give access to log on to the web UI. The account can be
defined to allow an FTP or FTPS access to the memory card.

 Guest
With the Guest role you have the lowest level access rights. As Guest you can only:
• change My details settings
• view events
• read drive parameters and see the statuses of the devices.
If you log on to the UI as Guest, the front page appears as follows:
54 Users

 User
With the User role you have the access rights of the Guest role supplemented with rights
allowing you to:
• write drive parameters
• select parameters for trend logging
• access data logger views
• view report settings
• view locale settings
• view the memory card and its contents
• export all drive parameters to the Events tab and save them to a PC
• import drive parameters from the PC file to a device.
If you log on to the UI as User, the front page appears as follows:

 Drive expert
The Drive expert role includes the access rights of Guest and User supplemented with
rights allowing you to:
• reset and rescan drives
• view network interface settings
• change locale settings
• view and change device interface settings.
 Users 55

If you log on to the UI as Drive expert, the front page appears as follows:

 Network admin
The Network admin role includes almost all the access rights of the Drive expert role plus
supplemental rights allowing you to:
• change network interface settings
• view and change network service settings
• view and manage user settings
• view and change NETA-21 settings
• restore settings to factory default values (software option)
• see the installed software type and version of the NETA-21
• reboot the NETA-21 (software option)
• view and change user interface settings
• change descriptions and prompts for the UI
• change the web server session time-out
• back up and restore tool parameters to the internal memory or SD card
• view the memory card status and reports folder on the SD card
• monitor the IP addresses of the logged-on users through events.
As Network admin you cannot:
• rescan device parameters or reset an active fault
• view and change device interface settings
• write device parameters
• select parameters for trend logging
• configure and control data loggers embedded in some monitored devices
• export or import device parameters to/from a file.
56 Users

If you log on to the UI as Network admin, the front page appears as follows:

 Tool admin
With the Tool admin role you have the full access rights to the NETA-21. In addition to the
access rights listed for Drive expert and Network admin, the Tool admin role allows you to:
• add and remove NETA-21 user accounts (and modify permissions of other users)
• perform the firmware update of the NETA-21 through the SD card or PC
• back up and restore the NETA-21 firmware and NETA-21 settings to/from the SD card
• enable or disable the factory login (factory support account)
• reset the tool settings to the default settings (restore the factory settings)
• add and remove extra software packages
• change report settings.
If you log on to the UI as Tool admin, the front page appears as follows:
 Users 57

User interface
The User interface tab is found under Settings. The text boxes on the tab can contain
embedded environment variables, in other words, the value of the environment variable is
shown in the text. The text may contain '{VARIABLE}' where VARIABLE means the name
of environment variable on the server. If text contains two braces ('{{' or '}}'), only one brace
is shown in the UI.
58 Users

The User interface tab contains the following components:

• Save button saves the modified settings to the NETA-21.
• Reset button discards all changes in the settings.
• Export button exports the UI settings to a local file.
• Import button imports the UI settings from a file to the UI.
• Help button opens a dialog box informing you about the embedded environment
variables in the UI.
• Tool name text box shows the name of the NETA-21 (the default is the same as the
tool type). This box may contain embedded environment variables. When you make
changes in this box, the following places will be affected:
• Web browser title shows the tool name.
• Application toolbar shows the tool name.
• Welcome instructions text box contains the welcome instructions for the UI. The
welcome instructions are shown on the front page after the first login. This box may
contain embedded environment variables.
• Tool description text box contains the NETA-21 description. This text is shown on the
front page after the login. This box may contain embedded environment variables.
• Login prompt information text box contains the information visible for all users in the
login dialog box. This box may contain embedded environment variables.
• Web session timeout drop-down list defines the time (in minutes) when the user is
logged out if there is no activity in the UI. The default value is 15 minutes. The
following values can be selected:
• 15 minutes
• 30 minutes
• 60 minutes
• 2 hours
• 6 hours
• 12 hours
• 14 hours
• indefinite.
Note: The web session expires in less than 5 minutes if the web browser is closed or
the connection to the NETA-21 is lost. The Web session timeout setting has effect
only if the web browser window is open. The time-out calculation is reset every time
when the user browses around in the UI.
 Devices 59

10
Devices

What this chapter contains

This chapter describes how to manage device parameters and use data loggers.

Devices tab

There are two tab pages under Devices:

• Devices tab lists all devices that are connected to the NETA-21.
• Events tab lists events for all detected devices.
The Devices tab contains the following components:
• All button shows all devices.
• Refresh button updates the device list. When the view is updated, the Refresh button
is disabled and the icon spins indicating that the updating is in progress.
60 Devices

• Navigate button opens the front page of a selected device. This button is disabled if
no device has been selected. If you click the arrow on the button and select
Parameters or Events, you can go directly to the Parameter browser tab or the
Event tab of the selected device.

• Device list shows all detected devices. Double-click a device to open the front page of
the device. The list contains the following columns:
• Name column contains the name and icon of the device.
After the device name there are two numbers in curly brackets. The first number
depends on the connection type:
0 = DDCS connection
1 or 2 = PNL connection
3 = Modbus connection
Ethernet connection = IP of the device without dots.
The second number is an ID that indicates different devices of the same
connection.
• Category column contains the category of the device.
• Type column contains the type of the device.
• Status column contains the connection status of the device and the corresponding
icon describing the status. The status can be, for example, one of the following:
Normal, Disconnected, Warning, Fault.
• Connection type column contains the connection type of the device. The following
connection types are available:
DDCS
ETH scan, ETH manual (Ethernet connection, either automatically scanned or
manually connected)
MB (Modbus)
Panel bus.
 Devices 61

 Device front page

Every device has its own front page which can be customized by the administrator. Every
user has the same layout. The front pages are portals where the user can move, add and
remove the contents.
• Example of a device front page:

The toolbar of the front page contains the following buttons:

• Refresh button refreshes the contents of the view. When the view is updated, the
Refresh button is disabled and the icon spins to indicate that the updating is in
progress.
• Add content button adds a new portlet to the portal. If you click the arrow on the
button, you get a drop-down list containing the following portlets:
• System info
• Device control
• Events
• Favorite parameters.
62 Devices

• Save layout button saves the layout. This button is visible only to device super users
and administrators that have permissions to modify the layout.
The front page contains the following portlets:
• System info portlet shows read-only information about the device.
• Device control portlet contains means to control the device. Every option contains a
title, icon and description. See section Device control buttons.
• Events portlet shows the latest events for the device. The event list contains the
following columns: Name, Timestamp and Severity. The list can be sorted.
• Favorite parameters portlet contains the parameters that are marked with a yellow
star on the Parameter browser tab. You can refresh the values of the parameters by
clicking the Refresh button of the front page.

Device control buttons

There are three device control buttons in the Device control portlet.When you click the
icon, the icon is disabled until the action has completed. If the action fails, a light-blue
warning message is shown under the description. The panel may contain the following
actions (the options may vary between devices):

• Rescan parameters button

The button is enabled when the associated drive is connected and parameter
scanning is not active on any of the drives handled by the same device interface (eg,
DDCS, panel bus, Ethernet, Modbus). In any other case the button is disabled.
The automatic parameter scanning starts if all connected devices per interface (or
panel port) become disconnected. Some interfaces such as Ethernet tool network may
scan for nearby devices continuously in the background.
There are situations when the parameter list of a drive and the content of the
Parameter browser tab become unsynchronized, for example, when the parameters
of a drive have been modified while it has been disconnected shortly from the NETA-
21. When you reconnect the NETA-21 to the drive, use this button to resynchronize
the parameters shown in the Parameter browser tab with the actual parameters of
the drive.
When you click the button for the first time, the icon and the text change as follows:

To start the parameter scanning, you must click the button again, otherwise the action
is cancelled after about 30 seconds.
• Reset fault button
The button is enabled when the associated drive is connected, there is an active fault
on a drive, or when a drive has an unacknowledged fault which has already ended.
In any other case the button is disabled.
 Devices 63

If the cause of the fault has been handled, you can reset the fault by clicking this
button. If a fault condition is active or a device has a permanent fault, the fault cannot
be reset via interferes.
• Remove button
The button is enabled when the associated drive has been disconnected from the
NETA-21. Use the button to permanently delete the drive from the drive list of a device
interface, for example, when the configuration of the system has changed.
The button is disabled when the drive has been reconnected to the NETA-21.

 Parameter browser
Every device has one or more parameter browser tabs that list the parameter groups and
parameters of the device. You can mark favorite parameters with yellow and blue stars.
Parameters marked with a yellow star are shown in the Favorite parameters portlet on
the device front page. Parameters marked with a blue star are shown in the Favorite
parameters portlet on the My frontpage tab.

The toolbar of the Parameter browser tab contains the following components:
• Filter parameters… is a text box for finding parameters from the parameter list. The
parameter list is updated automatically when you type search criteria to this box.
• Parameter status is a check box for showing or hiding the parameter status bar of the
parameter view at the bottom of the window. The status bar is visible by default.
• Refresh values button updates the parameter values visible in the parameter list.
When the view is updated, the refresh button is disabled and the icon spins to indicate
that the refreshing is in progress.
Note: The NETA-21 has a cached list of parameter groups and parameter names. The
Refresh values button does not necessarily update all group names on the list, since
that would take too much time. Some of the parameter data will be updated after a
delay when you start browsing into the parameter groups. If it is uncertain that the
parameter list is up to date or if there are strange access errors when you try to open
parameter lists, the errors can be solved by reloading all device-specific data. To
64 Devices

reload all device-specific data, click the Rescan parameters control button on the
device front page.
• Expand all button shows all parameters of all groups.
• Collapse all button hides all parameters and shows only the group list.
• Export button exports parameters to a file.
• Import button imports parameters to the device.
The status bar provides the following information:
• Parameters updated field shows how much time has gone since the parameter
structures have been updated from the device to the NETA-21. The NETA-21 keeps a
cached list of parameter structures, and someone else (a local user with a control
panel, a PC tool user, or the monitored device itself) may have changed parameters
after the last update. The elapsed time is shown as follows:
• Parameters updated X days ago
• Parameters updated X hours ago
• Parameters updated X minutes ago
• On-going operation field shows what the device is currently doing. The operation is
indicated with an icon and, for example, the following texts:
• Parameter list is up to date
• Refreshing parameters
• Device is disconnected
• Device is offline.
The parameter list is not sortable. The list contains the following columns:
• Name column shows the name of a parameter.
• Value column shows the value of a parameter. For parameters that have a decimal
value, the value is shown in the hex, decimal or binary format depending on the
selection made in the Parameter properties panel.
• Minimum, maximum and default value columns are hidden by default.
To add columns, click the arrow on the right-hand side of an existing column:

• Unit column shows the unit of the parameter value. This field may be empty for some
parameters.
• Internal type shows the data type of the parameter, either a device-specific type (eg,
float2 for a float number with two decimals) or a generic type (eg, "number" or "string").
When you select a parameter from the list, an edit panel titled Parameter properties
appears in the right-hand side of the tab.
 Devices 65

Parameter properties
Open the Parameter properties panel by clicking a parameter in the Name column. The
panel has two sub-panels that are visible one at a time.
• Modify panel has controls to modify the parameter value.
• Logging panel contains logging-specific settings and lists.
With the Modify sub-panel you can modify the parameter value.

The Modify sub-panel contains the following components:

• Value check box: There can be two value boxes to choose from depending on the
data type of the parameter. If there are two value boxes, only one of them can be
selected at a time, and the other is collapsed.
The box may be a spin box, check box grid, drop-down list, text editor or a parameter
selection control (parameter pointer or bit pointer). If there is the Parameter check
box, click the list to open a pop-up window where you can choose a parameter or the
bit of a parameter value.
66 Devices

Spin-boxes use the minimum and maximum value limits received from the device. You
cannot type the value.
• Format is a drop-down list for specifying the format of a parameter value. The format
can be Decimal, Hex or Binary.
• Export button exports the parameter in a text-based file.
• Apply changes button saves the parameter changes to the device.
The icon of the Refresh button is spinning while the changes are applied to the NETA-
21.
• Restore defaults button asks the device to restore the default value to a parameter.
This button is disabled if the parameter has no default value.
Note: You cannot modify the value or format of read-only parameters.
The Logging sub-panel contains logging-specific settings and lists:

The Logging sub-panel contains the following components:

• Signal name defines the name of the parameter that is used in reporting and trend
logging. The default name depends of the style selected in Reports –> Settings –>
Signal names –> Settings –> Default signal name. You can restore the default
signal name with the Restore default button or by storing an empty signal name.
• Interval drop-down list is used for selecting the logging interval for the current
parameter. You can select from the following values: Minute, 5 Minutes, Hour, Day,
None or Monitor. To save the value, click the Apply changes button.
• Log only when changed check box is used for selecting values to be logged only
when the parameter value changes. If this check box is not selected, the parameter
value is logged at every interval.
 Devices 67

• Open parameter logging history in a new tab button

• Refresh button updates the log list/chart if new values have been logged.
• Export logging history button creates a log report file to be exported.
• Toggle between chart and list view button changes the view in which the
logged values are displayed.
• Logging history shows all the logged values for the parameter in the current
segment.
• Apply changes button saves the parameter log changes.
• Restore default button replaces all changes in the settings with default values.

Export of parameters
When you click the Export button in the toolbar the following progress pop-up window
appears:

The progress pop-up window has a Cancel button which stops the exporting process.
With the Hide button you can hide the exporting pop-up window. The pop-up window is
shown again when you click the Export button.

Note: Only one parameter export can be ongoing at a time. If another user has started a
parameter export before you started a new export, your export may fail. In addition, you
cannot start an export, if drive parameters are being scanned in background.
Note: The parameter export format depends on the device type and device interface. The
parameter export is not available for all device interfaces.
68 Devices

Import of parameters
When you click the Import button you are asked for an import file.

The file is sent to the NETA-21 and the progress dialog box is shown. The NETA-21
supports the NETA-21, NETA-01 and DriveWindow parameter export files for importing.
Note: The format of the parameter import file is compatible with the NETA-21 parameter
export files, NETA-01 parameter export files and DriveWindow 2.x parameter export .txt
files (but not with DriveWindow parameter .dwp save files).
Note: Make sure that you import/export parameters only between identical drives and
device software versions.
It may be necessary to power cycle the drive and reload the device interface in the NETA-
21 to see all effects of parameter changes, especially if monitored devices change their
device interface node ID.
Note: The parameter import does not open a parameter lock or handle all dependencies
between parameters. Sometimes it helps when you import a parameter file multiple times.
Note: For the ACS800 firmware, the parameter import restores ID run parameters if those
are included in the parameter file. In addition, only visible parameters are restored.

WARNING! In importing specific parameter configurations you can cause the

drive to start during or after the parameter import. (Control words or signals in
groups <10 are not written to a drive during the parameter import). Keep it in mind
that the parameter import functionality can be dangerous if you have not made sure that
the drive can be started safely. Imported parameter settings must to be compatible with the
specific drive.
 Devices 69

Device data logger

 Data logger
The drives connected through a DDCS protocol have a data logger or data loggers that
can record data from various signals of the drive when there is no external logging
mechanism active. This can be used for troubleshooting or diagnostics. Data collecting
can be stopped by either a specific stop command or automatically by a triggering
condition becoming true in the drive. After the data collecting has been stopped, the
collected data can be read and studied.
The data logger tabs contains all uploaded data logs from the drive. One drive can have
multiple data loggers configured. All data loggers have an identical user interface.

The data logger tabs contain the following components:

• Refresh button refreshes the data logger view.
• Control button is a menu button that can be used to control the data logger with the
following actions:
• Start - starts the data logger.
• Stop - stops the data logger.
• Reset - restarts the data logger.
• Trigger - triggers the data logger manually.
• Settings toggle button shows the data logger settings in the editor panel.
70 Devices

• Triggers toggle button shows the data logger trigger settings in the editor panel.
• Export… button shows a drop-down list of two options: Events and Settings.

• Events option exports all collected recent data log files to a compressed .zip file
that can be opened with a PC.
• Settings option exports the currently opened data logger Settings and Triggers
panel configurations to a file that can be loaded to a PC.
• Import settings button allows you to import the previously saved data logger settings
and triggers from a file on a PC to a data logger in a monitored device.
• State defines the current state of the data logger with the following states:
• Not initialized
• Stopped – the data logger is not running/collecting data.
• Started – the data logger is running/collecting data.
• Filled – data logger upload is complete and data logger is not running/collecting
data.
The State is updated automatically every couple of seconds.
The Datalogger tabs show all uploaded data logs from the drive.

You can see the content of an entry by double-clicking the entry in the data logger list or by
clicking the plus sign beside it. You can close the content of an entry by double-clicking the
open entry in the data logger list or by clicking the minus sign.
The tabs contain the following columns:
• Name column shows the event name.
• Local time column shows when the event occurred. You can use the following filters
Before, After or On.
• Relative time column shows how much time has passed since the event occurred.
• Category column defines whether the event contains a device-produced data log file
(category: device generated datalog) or whether the event indicates a change in a
data logger state (category: device datalogger control).
 Devices 71

• Source column shows the source of the event. You can filter this field with a free text
box.
• Severity column defines the severity (or type) of the event (Detail, Notification,
Warning, Fault, Severe). You can filter this field to show only the wanted event types.
The columns can be sorted, hidden or filtered by clicking the header arrow, which appears
when the cursor is over the header.

The data logger records data before and after the triggering event, depending on its
settings.
For more information on the functionality of data loggers, see the drive-specific firmware
manual.

 Opening a data logger

1. Log on as a user with roles other than Guest or Net Admin.
2. Click Devices.
3. Select the device to be monitored with a data logger.
Note: All monitored devices do not provide data loggers. Data loggers are supported if
there is one Datalogger tab or more Datalogger tabs on the device-specific page.
4. Click the Datalogger 1 or Datalogger 2 tab to view the system data logs.
72 Devices

 Setting up a data logger

1. Open Datalogger 1 or Datalogger 2 (see above).
2. Click the Settings button to open the Settings sub-panel of the Datalogger
configuration panel in the right-hand side of the tab.

3. From the Datalogger auto control drop-down list select Only automatic upload
(data logger stops after it has finished collecting data) or Keep continuously running
(data logger is started whenever the logger is initialized or filled, even if the logger was
not initially running).
4. In the Channels box click the parameter you want to add and then click the Change
selected channel icon.
5. In the pop-up window select the new parameter you want to add to the list and click
OK.
 Devices 73

To leave the Channel box as it is, click Cancel.

6. Remove the unnecessary monitoring parameters by selecting them and clicking the
Remove selected channel icon.
74 Devices

7. Open the Triggers sub-panel.

In this panel you can adjust:

• Time step (ms): sampling rate of the data logger in the device.
• Trigger conditions: multiple choices depending on the monitored device.
• Trigger variable (parameter selection), Trigger level and Trigger hysteresis, if
the selected trigger condition requires the values. For example, a limit check
requires that the parameter and trigger level limit are specified.
• Pre-trigger count: number of the samples recorded in each data log before the
triggered event occurred.
Note: The number of available ranges and trigger options vary depending on the
monitored device. If the selected settings are not accepted by the monitored device
when you click the Apply changes button, the UI restores the original settings from
the monitored device to the Triggers panel.
8. From the Time step spin box select the time interval (in milliseconds) between data
readings.

9. From the Trigger conditions list select what device conditions will trigger the data
logger to send in the collected data.
An additional parameter value set in Trigger variable can be used to trigger the data
logger. Use the Trigger hysteresis spin box to set the signal value hysteresis.
10. In the Pre-trigger count spin box select the number of data entries that will predate
the trigger event.
 Devices 75

11. Click Apply changes.

12. Click Control and select Start to start the data logger or change the Only automatic
upload mode to the Keep continuously running mode in the Settings panel.

The State changes to Started indicating that data logger is running.

Device interface settings

 Device interfaces
The Device interfaces view is meant for device expert users who want to configure the
access to the monitored devices in fine detail. Device interface specific settings lets you
configure communication parameters as well as fine tune device specific settings.
Normally the NETA-21 configures device interfaces automatically and auto-discovers
connected monitored devices. Sometimes it is necessary to rebuild the device interface to
refresh the list of monitored devices. Devices in the selected interface are presented in a
generic fashion since new interfaces can be added to this view dynamically as new device
interfaces.
Every connection type has its own tab.

The toolbars of the tabs differ but all of them have the following buttons:
• Settings button opens an Interface settings dialog box that contains settings for the
selected device interface. The settings vary for every interface.
• Refresh button refreshes the device list in the current interface.
• Rescan devices button rescans a specific device interface to add/remove devices.
This button is not available for every device interface. The rescanning of devices is run
in the background for every device interface while no devices are connected, or when
all connected devices become disconnected. Some interfaces such as Ethernet may
be able to rescan for added devices in the background continuously.
• Restore defaults button restores the default values for settings and re-initiates the
scanning of devices within the selected interface. Previously connected devices may
be lost.
The device list on each tab has the following columns:
• Device column shows the name of device.
• Node ID column shows the node ID of the device interface.
• Category column shows the category of the device.
• Connection type column shows the connection type of the device.
76 Devices

When you select a device from the list, the Device parameters panel appears in the right-
hand side of the tab. The content of the Device parameters panel is specific for each
connection type, but the following components can be found in all of them:
• Device name box sets a custom name for the device.
• Apply changes button saves the modified device settings.
• Restore defaults button discards the changes made before the Apply changes
command was given.

 Ethernet tab
The Ethernet tab contains all the devices that the NETA-21 finds in its Ethernet tool
network.

Note: If there is an ACS880 drive equipped with a FENA-11/21 adapter module in the
Ethernet network, the NETA-21 and the Drive composer PC tool cannot access the FENA-
11/21 at the same time. The FENA-11/21 can have only one PC tool connection at a time.
The FENA-11/21 connection can be released for a PC tool by removing the specific
Ethernet device from the NETA-21 device interfaces view (or by clicking the Remove
button on a specific Ethernet device front page).
The toolbar of the ETH tab contains the following two extra buttons:
• Add button allows you to add a device to the list by specifying its IP address.
• Remove button removes the selected device from the list.
Note: By default, the NETA-21 discovers devices automatically via the Ethernet tool
communication connected to port ETH2. To modify the background scan settings click the
Settings button.
 Devices 77

 Modbus tab
The Modbus tab contains all the devices which use the Modbus/RTU protocol and which
are connected to the NETA-21 through serial port.

The toolbar of the Modbus tab contains the following extra buttons:
• Add button allows you to add a device to the list by specifying the following properties:
• Device Name is a text box for the custom name of the device.
• Modbus node ID is a spin box for the node ID configured in the monitored device.
• Drive template is a drop-down list for the template to be used with this device. A
template is a file provided by ABB that is stored under the "template" folder in the
SD card or internal memory.
• 32-bit registers is drop-down list for selecting 16-bit or 32-bit values of
parameters. There are three options:
As in template, 16-bit if unset
As in template, 32-bit if unset
Force all values to 32-bit
• 32-bit register word order is a drop-down list for selecting the most or least
significant word order for 32-bit values. There are two options:
High-low
Low-high
• Remove button removes the selected device from list.
• Rescan devices button performs a rescan that searches for all Modbus-connected
devices.
Note: The Modbus/RTU rescan uses a selected communication speed (defined in
Interface Settings dialog box). The rescan runs continuously in the background if all
devices are disconnected.
Click a device in the list to open the Device parameters panel where you can change the
Modbus node ID and the 32-bit register word order.
78 Devices

 DDCS tab
The DDCS tab contains all the devices which use the DDCS protocol and which are
connected to the NETA-21 through fiber cables (via the NEXA-21).

Click a device in the list to open the Device parameters panel where you can change the
value of the Main status word to Not set, Dataset 2 or Dataset 11.
Note: The Main status word dataset is normally auto-detected during the device detection.
If a wrong value is selected, the device fault and warning statuses are not indicated
correctly.

 Panel bus tab

The Panel bus tab contains all the devices connected to the PNL connectors.
 Devices 79

 Interface settings
To open the Interface settings dialog box, click the Settings button on the toolbar. Every
connection type has its own Interface settings dialog box. The following two buttons are
common to each connection type:
• Save button saves the modified settings.
• Close button closes the dialog box without saving the settings.

ETH settings
The Interface settings dialog box of the Ethernet connection contains the Background
scan drop-down list.

With the Background scan function you can define how the automatic device discovery
works. There are the following options:
• Disabled: Devices are not automatically discovered.
• ETH1: Automatic discovery works only on the first Ethernet port.
• ETH2: Automatic discovery works only on the second Ethernet port.
• Both: Automatic discovery works only on both Ethernet ports.
80 Devices

Modbus settings
The Interface settings dialog box of the Modbus connection contains three drop-down lists.

• Communication Speed is a drop-down list for setting the speed of the Modbus
communication. The available speeds are the following:
• 9600 bps
• 19200 bps
• 38400 bps
• 57600 bps
• 115200 bps
• 230400 bps.
• Communication Mode is a drop-down list for setting the serial communication mode.
The available values are the following:
• 8-N-1: 8 None 1
• 8-E-1: 8 Even 1
• 8-O-1: 8 Odd 1
• 8-N-2: 8 None 2.
• Background scanning is a drop-down list for enabling or disabling the automatic
device discovery. The background scanning uses the selected communication
settings. The background scanning runs only if there are no connected devices, or if
all devices have become disconnected.
 Devices 81

DDCS settings
The Interface settings dialog box of the DDCS connection contains four drop-down lists.

• Optical Power is a drop-down list for defining the value from 1 (lowest) to 4 (highest).
• Communication Speed is a drop-down list for defining the value from 1 to 8 Mbit/s.
• Network Topology is a drop-down list where you can choose values Star or Ring.
• Ethernet GW is a drop-down list for enabling or disabling the Ethernet gateway for a
remote DriveWindow PC tool (2.4 or later) connection. The gateway is disabled by
default.
Note: The settings depend on the configuration required by a device interface.
Panel bus settings
The Interface settings dialog box of the Panel bus connection contains two drop-down lists
and two text boxes.

• Cable check is a drop-down list for enabling or disabling the function.

• When the cable check function is enabled, the NETA-21 tries to identify the
connected cable (by testing the input voltage from the drive control board). The
panel bus connection scanning runs in the background only if the cable (input
voltage) is detected on the PNL1 or PNL2 port.
• When the cable check function is disabled, panel ports are scanned continuously
even if the cable is not connected. If the input voltage is not available from the
panel bus, this option can be used for detecting panel bus devices. When the
cable check function is disabled, there is extra background CPU load in the NETA-
21. The PNL1/PNL2 LEDs are red if no panel bus device cannot be detected. See
LED indications of the NETA-21.
• Ethernet GW is a drop-down list for enabling or disabling the gateway mode.
• Connection speed (pnl1) shows the speed for the active connection.
• Connection speed (pnl2) shows the speed for the active connection.
82 Devices
 Networks 83

11
Networks

What this chapter contains

This chapter explains how to set up and configure Ethernet network interfaces of the
NETA-21.

Network interfaces view

The Network interfaces view (Settings –> Network interfaces) is split into two interface
specific tabs: Ethernet 1 and Ethernet 2.

In addition to the Ethernet panel and Network status panel, the Ethernet interface tabs
contain the following components:
• Save button saves the changes to the NETA-21. When you save the settings, they are
applied to use immediately. A dialog box warns that the connection to the web pages
can be lost, if the IP address of the NETA-21 is changed. You can either continue or
cancel the changes.
• Reset button discards all changes made by the user.
• Export button exports the Ethernet settings to a local file.
84 Networks

• Import button imports the Ethernet settings from a file to the UI.
• Test interface button opens a dialog which can be used for sending a ping message to
a defined address.
• Reboot tool button is used for rebooting the NETA-21. You are redirected to a waiting
page.

 Test interface
When you click the Test interface button the following dialog box appears:

The Ping server dialog box contains the following components:

• Server to ping box defines the address of the server where the ping message is sent.
• OK button sends the ping message and opens a dialog to show the result.
• Cancel button closes the dialog box.
The following Ping status dialog box appears after the ping message has been sent:

The Ping status dialog box contains the following components:

• Interface field shows the interface that was used for sending the ping message.
• Ping status field shows whether the sending of the message has failed or succeeded.
• Output field shows the console output for sending the message.
• OK button closes the dialog box.
 Networks 85

 Ethernet panel

• Mode has two options for selecting either an automatically obtained or a static IP
address:
• Obtain an IP address automatically option disables the IP address, Subnet
mask and Default gateway boxes. This is the default setting. When this mode is
selected, the NETA-21 tries to retrieve its IP address from the DHCP server. If the
DHCP address retrieval fails, the NETA-21 defaults to a “zeroconf” IP address in
format 169.254.x.y where x and y are randomly selected numbers.
• Use the following IP addresses option requires you to configure the fixed static
IP address settings by filling in the following boxes: IP address, Subnet mask,
Default gateway, Preferred DNS server and Alternate DNS server.

 Network status panel

• Disable DHCP button disables the DHCP server mode. The button is visible only
when the DHCP mode has been activated with the SD RJ45 button.
• IP address field shows the currently used IP address for the interface. If the field is
empty, no IP address has been defined. If the link status is "down", a message
indicating this is shown instead. This field cannot be modified.
• Netmask field shows the current network mask. If the field is empty, no mask has been
defined. This field cannot be modified.
• Gateway field shows the default gateway for the specific interface. This field cannot be
modified in the Network status panel.
86 Networks

Network services
The Network services view (Settings –> Network services) shows the connectivity of the
NETA-21 with outside world over Ethernet.

For example, time services are located in the Locale settings view. Some of the out-bound
reporting services such as email and FTP are configured in the Report view.
The Services tab contains the following components:
• Save button saves the changes to the NETA-21.
• Reset button discards all changes made by the user and restores the default settings.
• Export button exports the visible settings to a local file.
• Import button imports the settings from a file to the UI.
• Test SMTP settings button asks you for an email address. The UI uses the visible
SMTP settings to send a test email to the specified email address.
• Reboot tool button reboots the NETA-21.
The Services panel, Services settings panel and Mail servers (outgoing) panel are
described below.
 Networks 87

 Test SMTP settings

The Test SMTP settings dialog box contains the following components:
• From text box defines the email address of the sender.
• To text box defines the email address of the receiver.
• Subject text box defines the subject for the email message.
• Content text box defines the content for the email message.
• OK button closes this dialog box and sends an email to the receiver.
• Cancel button closes this dialog box.

 Services panel
The Services panel has one service defined in every row. You can enable or disable the
service per each interface. You can also select the service to be enabled for all interfaces.

The list has the following columns:

• Service column has every available service listed. After the service name there is an
icon. By clicking the icon a popup dialog box or a tooltip is opened providing more
details about the service.
• Interface column has multiple sub-columns. All interfaces are below this column.
• All column is always visible and enabled. The column has a check box which is
selected if the service has been enabled for all interfaces.
• When the All check box is selected all other check boxes in the interface column
are selected as well (in the same row). The All check box disables any firewall
limits and allows the service to be reached over any network connection.
• When the All check box is not selected all other check boxes in the interface
column are unselected as well (in the same row).
• Interface X column shows what services are selected for the current interface. It is
possible that there is no interface X column since the available interfaces depend on
the tool configuration and type. There may be multiple interface X columns containing
a check box.
88 Networks

 Services settings panel

The Services settings panel contains the following components:

• Prefer HTTPS is a check box for defining that HTTPS is used when possible.
If prefer the Prefer HTTPS check box is selected, the UI login page forwards users
always to the HTTPS protocol version of the login page.
• Extra HTTP port is a text box for defining an additional HTTP port. If this box is empty,
no additional port is used.
Note: The NETA-21 provides the HTTP version of the web pages always in port 80.
• HTTPS port is a text box for defining the HTTPS port. The default value is 443.
• FTP port is a text box for defining the FTP port. The default value is 21.
• FTPs port is a text box for defining the FTPS port. The default value is 990.
Note: In the NETA-21 the FTPS client program is configured to use Explicit TLS
encryption.
• NetBios hostname is a text box for defining the host name for the NetBios service,
which facilitates the access to the NETA-21 with a local name instead of an IP address
in some local network environments. The default value is "neta".

 Mail servers (outgoing) panel

The Mail servers (outgoing) panel contains the following components:

• Primary server is a text box for defining the primary server for the SMTP service.
• Secondary server is a text box for defining the secondary server for the SMTP
service.
• Port is a text box for defining the SMTP port for the SMTP service. The default value
is 25. Both primary and secondary mail servers have their own ports to be configured.
• Username is a text box for defining the user name for the SMTP service. Both primary
and secondary mail servers have their authentication settings to be configured. The
Username and Password boxes can be left empty if the SMTP server does not require
authentication.
 Networks 89

• Password is a text box for defining the password for the SMTP service. Both primary
and secondary mail servers have their authentication settings to be configured.
• Enable SSL encryption is a check box for enabling the SSL encryption for the SMTP
service. Both primary and secondary mail servers have their encryption settings to be
configured.

DHCP
For instructions on setting up a DHCP server, see Connecting a local PC to the NETA-21
in the DHCP server mode.

HTTP/HTTPS
HTTP is the default protocol setting in the NETA-21. To switch from HTTP to HTTPS edit
the address from http://192.168.230.1 to https://192.168.230.1. This can also be done by
selecting the Prefer HTTPS check box in Network services.

Starting up the SMTP configuration

1. Make sure that the NETA-21 is able to access the specified SMTP server over
Ethernet.
2. Go to Settings –> Network services –> Mail servers (outgoing) and set the
appropriate server settings.

3. To check the SMTP settings, click Test SMTP settings, type the test email addresses
and click OK.

If the test succeeds, the following message is shown.

90 Networks

If the test fails, the following message is shown.

If the SMTP settings are correctly configured, the email reporting process is successfully
set up and it is possible to send reports with the NETA-21. See Reporting.

Dynamic DNS
The NETA-21 provides support for the Dynamic Domain Name System (DDNS).
The Dynamic DNS service is useful when you have to access the NETA-21 with a dynamic
IP, for example, when the NETA-21 is located in an isolated region where the only network
access is through a 3G modem.

 Using the Dynamic DNS service

1. Go to Settings –> Network interfaces –> Dynamic DNS.

The toolbar of the Dynamic DNS tab contains the following buttons:
• Save button saves the user configuration to the NETA-21.
No external file is generated.
• Reset button discards all changes you have made and resets the fields to default
values.
• Export button exports the DDNS settings to a local file.
• Import button imports the previously exported DDNS settings from a file to the UI.
2. Select the Enable dynamic DNS check box.
3. Fill in the following text boxes:
• Dynamic DNS service: contains a list of all DNS service providers that can be
used.
 Networks 91

After you have registered to one of the supported Dynamic DNS service
providers, you get a host name, user name and password.

• Hostname: is the name assigned to the NETA-21.

Host name must be registered at the selected service provider.
• Username: defines the user name for the DDNS service.
• Password: defines the password for the DDNS service.
Now you can access the NETA-21 web interface by using the registered host name.
For example, if you have registered to the dyndns.org service with host name “my-neta-
21”, you can access the NETA-21 with address “my-neta-21.dyndns.org”.

Dial-up function
In isolated regions, the mobile broadband may be the only way to have an Internet
connection. With the dial-up function you can use a USB 3G modem for establishing an
Internet connection to the NETA-21 via the USB port (see section Layout of the NETA-21
and the NEXA-21).
Note: The NETA-21 searches for connected modems via the USB and RS-232 ports. The
modems connected to the USB port of the NEXA-21 are not detected. The modem must
support either GPRS, EDGE or 3G connections.
Only the following tested USB modem models function correctly with NETA-21:
• Huawei E153
• Huawei K3715
• Vodafone K4505.
Other modems may be detected by the NETA-21 but have not been tested for
compatibility. For example, the connection establishment may not be reliable with untested
modems. The USB modems acting as an Ethernet adapter to a PC (USB modems which
provide a web UI) are not compatible with the NETA-21.
92 Networks

The dial-up function is located on the Dial up tab under Network interfaces.

The toolbar contains the following buttons:

• Save button saves the changes to the NETA-21.
• Reset button discards all changes you have made.
• Export button exports the modem settings to a local file.
• Import button imports the modem settings from a file to the UI.
• Test interface does the ping test with a defined URL.
The Modem settings panel contains the following components:
• Select modem is a drop-down list for selecting the installed modem.
• Connection type shows the connection type of a modem.
• Search button detects the installed USB modems.
The General settings panel contains the following components:
• Pin code text box is for the PIN of a SIM card.
• Test button verifies the PIN.
• Modem info button provides additional information about the modem.
The Dial up and GPRS settings panel contains the following components:
• Enable dial up is a check box for selecting the dial-up function.
• Host to ping is a text box for the defined URL needed in a ping test.
• Ping timer is a text box for defining the PING operation delay.
• Access point name is a text box for defining the access point name of the provider to
access the Internet
• Phone number is a text box for a phone number.
• Username is a text box for the user name needed if the modem service is enabled.
• Password is a text box for the password needed if the modem service is enabled.

 Using a mobile broadband connection

1. Plug the USB 3G modem into the USB port.
2. Go to Settings –> Network interfaces –> Dial up.
3. Select the modem from the Select modem drop-down list.
 Networks 93

If the modem is not already available in the list, click the Search button.

4. Select the Enable dial up check box.

5. Type all necessary information in the Dial up and GPRS settings panel.
6. Click the Save button.
7. Click the Events tab to check that the Internet connection has been established.
94 Networks
 Events 95

12
Events

What this chapter contains

This chapter describes how to observe and filter events.

Universal event list

The Event tab is virtually omnipresent in the UI. The contents of the tab may vary slightly
in different views. The following figure shows the Event tab under Home. This tab shows
all events.
The past events of the monitored device are grayed out.
By default all events are sorted by the occurrence of the event. Device events, however,
are sorted by the device-specific time.
96 Events

The tab contains the following components:

• Refresh button updates the contents of the tab.
• Filter events button opens and closes the Event filter panel at the bottom of the view.
• Show local/relative/device timestamp check boxes add columns showing the
local/relative/device time for the events:
• Local time column shows all time values according to the local time of the NETA-
21
• Relative time column shows all time values in a relative format, for example 3
days 3 hours ago
• Device time shows all time values according to the time set in the device.
• Export button exports all the events and data logger data to a .ZIP file.
• Clear filtering button clears any filtering that has been performed for the event list.
This button will be disabled if no events have been filtered. Filtering is available by
clicking on event list column titles.
Note: Filtering is applied only on the web browser side and for the visible (usually 100
latest) events only. Filtering can empty the event list even if there were matched
events in the event storage of the NETA-21 (in an older event history).
 Events 97

 Contents of the non-universal event list

The non-universal event lists do not show all events. For example, the Event tab under
Devices shows only device-related events.

Filtering settings by columns

The filtering criteria can be set separately for each column. In the heading row of the event
list there are arrow icons opening a menu for setting the filtering criteria for each column.
98 Events

The event list contains the following column headings:

• Event ID column shows the event ID number. The column can be sorted with a
numeric filter (less or more than or equal to the event ID number). The column is not
visible by default.
• Name column shows the event name. A balloon icon is shown if the event contains
comments. The column can be sorted with a search text box.
• Local time column shows when the event has happened. Device events are
synchronized with the NETA-21 clock.
• Relative time column shows how much time has passed since the event has
happened. You can use the following filters: Before, After or On.
• Device time column shows the event time from the device itself.
The device time can represent a run time counter for some drives. The device time is
only available for faults and warnings originating from a monitored device.
• End time column shows the ending time for the event. The menu has the following
filtering criteria: Before, After and On.
• Category column shows the event category. The column can be sorted with a search
text box.
• Source column shows the source of the event. The column can be sorted with a
search text box.
• Severity column defines the severity (or type) of the event. The menu has the following
filtering criteria: Detail, Notification, Warning, Fault and Severe.
If there is an attachment for the event, the attachment can be exported by clicking the icon
with an orange arrow.

To select the page, use the toolbar at the bottom of the Event tab.
 Events 99

Filtering settings through the Event filter panel

The event list can be sorted by defining the filtering criteria with the Event filter panel.The
Event filter panel is opened by clicking the Filter events button.
Note: The event filter panel provides more accurate search results than column filter and
search options, because it initiates a search within the web UI server. Column filters only
search within the visible data items (for example the 100 latest events).

The Event filter panel contains the following components:

• Number of events in page spin box defines the number of events shown in a single
page. The values can range from 10 to 200. The default value is 100.
• Show events after has two boxes with which the date and time can be defined for
events occurring after the selected timestamp. The boxes can be empty.
• Show events before has two boxes with which the date and time can be defined for
events occurring before the selected timestamp. The boxes can be empty.
• Sort by drop-down lists define the sorting column and sorting direction. The default
setting is Event ID in ascending order. The latest added events appear at the top of the
event list, even if the event timestamps are not in chronological order.
The first Sort by drop-down list contains the following items:
• Event ID
• Starting time
• Ending time
• Category
• Severity.
The second drop-down list contains the following items:
• Ascending
• Descending.
• Category box contains all available categories with check boxes. The categories have
sub-categories. The categories are selected and unselected by clicking the check
boxes. Under Settings the Category box in the Event filter panel shows only the pre-
defined categories. In general all the categories are shown and selected by default.
• Severity box contains the types of events with check boxes. The icon representing the
severity of the event is shown next to the text. By default, all types are selected except
Detail. If no type is selected, the types are not prioritized at all. The box contains the
following types:
• Detail
• Notification
• Warning
• Fault
• Severe
100 Events

• Filter events button makes the query to the server. After the query has succeeded, the
Event filter panel is hidden and the list of events is updated. If events do not fit to a
single page, the toolbar at the bottom of the Event tab can be used for changing
pages.
 Reporting 101

13
Reporting

What this chapter contains

This chapter describes how to make reporting and trend logging settings for configuring
which time levels and event categories are sent out by a reporting plug-in.
The tabs under Reports are described from left to right.

Introduction to reporting
With the NETA-21, reporting means that parameter values or event data of a drive or
several drives connected to the NETA-21 are sent periodically to the users. The NETA-21
reporting provides many ways to save or send the report. The NETA-21 supports the
following reporting methods:
• Email reporting – reports are sent via email
• SD card reporting – reports are saved to an SD card
• FTP reporting - reports are transferred to an FTP server.
The NETA-21 can be configured to send reports based on triggers. The triggers can be
time intervals, values of some parameters or drive events such as faults or warnings.
For example, it is possible to save all or some parameter values periodically to an SD card
or to upload them to an FTP server. In addition, you can configure the NETA-21 to send
emails when a drive enters a faulted state. By default the NETA-21 stores all changed
parameters and drive events to an SD card daily.
In email reporting it is possible to create a custom report format.
102 Reporting

Configuring the NETA-21 for reporting

To configure the NETA-21 for reporting, specify the logging intervals of the parameters
needed in the report:
1. Go to Reports –> History logging.

2. Click a parameter and select the interval in the Parameter properties panel.

If you want to set the intervals for several parameters simultaneously, go to

Reports –> Settings –> Settings –> Log intervals. For more information, see Log
interval templates.
 Reporting 103

Creating an email report

Note: To be able to use the email reporting, you must configure the SMTP settings. See
section Network services.
Note: Make sure that you have set the logging intervals for the parameters (Reports –>
History logger). If you have not set the logging intervals for the parameters, the reports
will have no data.
1. Go to Reports –> Settings and click the Add button.
2. Select E-mail reporting from the drop-down list.

Now the new report has been added to the list of reports.
3. Define the general settings of the report, such as report name and reporting trigger.
See section Setting the report trigger.
4. When you have named the report and selected the trigger, click the Reported data
sub-panel.
Here you can select the data to be reported. See Setting the reported data.
5. Click the Output settings sub-panel and define the settings.

• Enable report is a check box for enabling the email reporting.

• Report output format is a list for defining the template used in the report.
• From address is a text box for defining the sender.
104 Reporting

• To address is a tex box for defining the email recipient.

Note: To send an email to several recipients, separate the email addresses with a
comma or semicolon.
• E-mail subject is a text box for defining the subject of the email.
• Site identifier (default: serial no. of tool) is a text box for defining the identifier
used in the reports.
6. Click the Create report button.
To check that the report has been successfully sent, go to Reports –> Reported data.
If no report has been sent, check the network and email settings.

 Format of the email report

The reported data is shown in the email message body.
If you have selected an XML format, the email report looks like the following example:

If you have selected a plain text format, the email report looks like the following example:

You can create a custom format by using the report scripting section in an email report. For
more information, see section Using scripting for email reports (custom report).
 Reporting 105

Creating an SD card report

The NETA-21 contains two default reports: Daily parameter report to SD card and
Device event report to SD card. These reports store .csv and .log files to the SD card
when new faults and warnings occur on monitored devices. You can modify or remove pre-
defined reports or define additional reports to the SD card.
Note: Make sure that you have set the logging intervals for the parameters (Reports –>
History logger). If you have not set the logging intervals for the parameters, the reports
will have no data.
1. Go to Reports –> Settings and click the Add button.
2. Select SD card reporting from the drop-down list.
Now the new report has been added to the list of reports.
3. Define the general settings of the report, such as report name and reporting trigger.
See section Setting the report trigger.
4. When you have named the report and selected the trigger, click the Reported data
sub-panel.
Here you can select the data to be reported. See Setting the reported data.
5. Click the Output settings sub-panel and define the settings.

• Enable report is a check box enabling the SD card reporting.

• Folder path is a text box for specifying the location of the reports on the SD card.
If there is no folder, it will be created automatically. The default folder path is the
serial number of the NETA-21.
• Cleaning of SD card is a list for enabling the cleaning of an SD card when the SD
card is full or, alternatively, for stopping the reporting.
6. Click the Create report button.
To check that the report has been successfully sent, go to Reports –> Reported data.
Note: If the report does not appear on the SD card, check that the SD card is not full.
106 Reporting

 Format of an SD card report

The SD card reports are in the CSV format. CSV files with parameter values have
extension .CSV and event data reports have extension .log (or .evt in earlier firmware
revisions prior to firmware revision 2.20).
Each report is created in a subfolder of the folder specified in the Output settings sub-
panel. The folder structure is: SD:/report/Folder path in Output settings/Year/Month/Day/.
The report file names on the SD card follow format <ddhhmm>[_<n>] where <ddmmss>
indicates the day of the month, hours and minutes. An optional numeric posfix "_1", "_2",
"_3" ... "10", "11" ... "99" is added if multiple log files are written during one minute.

The SD card report for logged data looks like in the following example. An event report
looks similar except that there are more event-specific columns beginning with an
ampersand “&”.
 Reporting 107

Creating an FTP report

Note: Make sure that you have set the logging intervals for the parameters (Reports –>
History logger). If you have not set the logging intervals for the parameters, the reports
will have no data.
1. Go to Reports –> Settings and click the Add button.
2. Select FTP reporting from the drop-down list.
Now the new report has been added to the list of reports.
3. Define the general settings of the report, such as report name and reporting trigger.
See section Setting the report trigger.
4. When you have named the report and selected the trigger, click the Reported data
sub-panel.
Here you can select the data to be reported. See Setting the reported data.
5. Click the Output settings sub-panel and define the settings.

• Enable report is a check box enabling the FTP reporting.

• Create folder is check box for enabling the creation of a new folder.
• Folder path is a text box for defining the path to the folder in which the report is
created.
• Hostname is a text box for the address of the host provider.
• Port is a list for setting the port via which the FTP connection is carried out.
• Number of retries is a list for defining the number of retries during communication
breaks.
• Username is a text box for the name of the account user.
• Password is a text box for the password needed to a verified connection.
6. Click the Create report button.
To check that the report has been successfully sent, go to Reports –> Reported data.
108 Reporting

 Format of an FTP report

The FTP reports are in the CSV format. CSV files with parameter values have extension
.CSV and event data reports have extension .log (or .evt prior to firmware revision 2.20).
Each report is created in a subfolder of the folder specified in the Output settings sub-
panel. The folder structure is: /Folder path in Output settings/Year/Month/Day/. Each report
has a unique name with a time stamp.
 Reporting 109

Setting the report trigger

1. To define the report trigger, go to Reports –> Settings –> Reports –> New report –>
General settings.

2. From the Report trigger list, select the frequency for the report generation:
• Every minute
• Every 5 minutes
• Every hour
• Every day
• Every week
• Every month
• When new data available
Parameter has a new value or there is a new event.
• Any device state changed
Status of any of the drives has changed.

Note: You can select the statuses to be monitored.

110 Reporting

• Device state changed

Status of a particular drive has changed.

Note: You can select the drive to be monitored.

• Parameter value
Value or another parameter can be specified as a basis for comparison.
Bitmask is ANDed to the original value before comparison.
 Reporting 111

Setting the reported data

1. To define the data type for the reports, go to Reports –> Settings –> Reports –> New
report –> Reported data.
2. Select the data type from the Data type drop-down list.

• If you select Event, you can report events according to severity and category.
• If you select Logged data, you can report all parameters according to the logging
interval defined in section Configuring the NETA-21 for reporting.
• If you select Custom, you can specify the custom data from the Reported
custom data list.

If you select Custom event, you can report an event of a given severity with a
specified name every time the event occurs.
112 Reporting

If you select Parameter export, you can report all parameters of a particular
drive.
If you select Imported settings, you can restore the settings defined with the
backup and restore function. See chapter Backup and restore.
3. To preview the contents of the report, click the Preview data… button.
• If you selected Event, the content of the report looks like in the following example:

• If you selected Logged data, the content of the report looks like in the following
example:
 Reporting 113

Changing the reporting name

You can customize the reporting name for each connected device. The reporting name
and the optional reporting name are added as a prefix to the logged signal names, if you
have selected so (Reports –> Settings –> Settings –> Signal names, see Changing the
default naming of signals).
1. Go to Reports and click the row of the device which you want to rename.
2. Type the new name to the Reporting name text box.
3. Click Apply changes.

To update the device list, click the Refresh button.

From firmware version 2.20 onwards, you can customize also other device-specific
reporting attributes, for example the serial number and device type. Editable attributes
depend on a specific device.
114 Reporting

Changing the default naming of signals

There are two locations where you can manually name each trend-logged parameter
value: Parameter browser tab under each monitored device and History logging tab
under Reports.
If you have not typed in any customized name for the trend-logged variables, the default
naming is used for the parameters.
1. To define how the NETA-21 names the trend-logging variables by default, go to
Reports –> Settings –> Settings –> Signal names.

2. From the Default signal name list, select one of the following options:
• Group and parameter number provides the parameter with a name such as
"03_02" (default setting prior to firmware version 2.20)
• Parameter name provides the parameter with a name such as
"main_status_word"
• Parameter group, number and name is a combination of the two options above,
for example, 03_03_main_status_word (default setting from firmware revision
2.20 onwards).
3. Optionally, define a prefix for each device reporting name in the Device reporting
name prefix text box.
4. If you select the Include device reporting name in default signal name check box,
the device reporting name set under Devices tab is prefixed to the signal name.
The example of the default name is shown in the Settings panel.
 Reporting 115

Log interval templates

Use log intervals (Reports –> Settings –> Settings –> Log intervals) to modify the
logging intervals of multiple parameters simultaneously instead of modifying the logging
interval of parameters one by one via the Parameter history logging tab.
With the log intervals function you can also bulk-change certain other attributes related to
parameters and reporting such as the reported parameter names and only the Log only
when changed selection on the parameter specific logging settings. All available logging
interval templates are matched to all connected monitored device parameters when the
Apply changes button is clicked. Templates are applied to newly connected devices also
when any new monitored device is connected to the NETA-21 (and after the device
interface has been reset to the default settings).

Use the Send template to tool… button to save the template defining the set of rules
applied to the logging interval of parameters.
Under the Logging interval templates heading you can see the list of saved templates. If
you click the Run templates button, you can check some of the saved templates.
The Delete template button deletes the currently focused template file from the NETA-21.
116 Reporting

A sample content of a logging interval template file is shown below:

• device_attributes is a list of drive attributes that determine the drives to which the
template is applied.
• Possible attributes are: category for the category of the device, sw_pkg for the
SW package, sw_appl for the SW application.
• Values for these attributes are usually shown on the device front page and you
can use wild cards, for example, *(asterisk).
• If you do not specify any attributes, the template is applied to all devices.
• rules is a list of rules that define the parameters and values.
• param_id defines the index of the logged parameter, eg, "12.34
• unit defines the engineering unit of the monitored parameter, eg, "V" or "mA"
• either param_id, unit or both rules must be specified or the specific rule will not be
applied to any parameter.
• interval, signal_name and log_only_when_changed specify values that are applied
to the log interval of time, signal name and the Log only when changed selection of
the previously specified parameters.
• interval can be one of these values: “minute”, “5minutes”, “hour”, “day” and
“none”.
• signal_name can be any valid string.
• log_only_when_changed is true or false.
The following is an example of the logging intervals template that applies an interval of 1
minute to parameter 01.01:
 Reporting 117

The following is an example of the logging intervals template where the reported signal
name of parameter 01.01 is changed to “percentage” only when the unit of the parameter
is %:
118 Reporting

Using scripting for email reports (custom report)

To see the scripting panel of email reports:
1. Go to Reports –> Settings –> Reports –> New report –> Output settings.
2. Select Custom from the Report output format drop-down list.
3. Click the Report scripting sub-panel.

The Report scripting sub-panel contains the following components:

• Preview report is a drop-down list with two options: Parameter report and Event
report. Click these options to open a Preview dialog box containing a report
generated by the currently visible script. The report is generated by using a
predefined data. If the script contains an error, the error is displayed in the preview
dialog box.
• Predefined scripts is a drop-down list with three options: Custom report, XML
report and Plain text report. If you select a predefined script from the list, the
script editing text box shows that specific predefined script.
• Script editing text box contains a script which is used for generating parameter
and event reports. If you have modified the content of a predefined script and want
to restore the predefined script, select an appropriate form from the drop-down list
and click Restore defaults.
The JavaScript language is used to format the email output. You can modify the report
scripting code. Use the template scripts to produce XML and CSV formatted outputs.
Note: If you edit an invalid JavaScript code, all reporting may stop. If the reporting freezes
completely as a result of an invalid script, you may have to restart the NETA-21. Before
restarting the NETA-21, choose a pre-defined reporting template and save the report
settings.
Use the provided code templates, since there is no detailed programming guide on the
report scripts available.
 Reporting 119

Description of the tabs under Reports

There are five tabs under Reports: Settings, Devices, Parameter history logging,
Reported data and Configuration events.

 Settings tab
You can define which reporting plug-in is used in reporting when a log segment ends. For
information on the customizable reports, see Introduction to reporting, Creating an email
report, Creating an SD card report and Creating an FTP report.

The Settings tab contains the following components:

• Refresh button refreshes the contents of the parameter list.
• Add button adds a new report to the list of reports. The button is enabled only when
the Reports folder is selected.
• Remove button removes the selected report.
• Export button downloads the saved settings of the selected report.
• Editor panel means the area appearing on the right-hand side of the Settings tab
when you have selected one of the items on the left-hand side of the Settings tab.
• Import button imports a report from a file to the NETA-21. If the imported report has
the same name as an existing report in the NETA-21, then the report in the NETA-21 is
overwritten with the file.
• Help button opens a dialog box providing information about the settings of the view.
• Tree structure shows all active reports and available settings. When an item is
selected, the Settings panel appears on the right-hand side of the Settings tab.
120 Reporting

 Devices tab
On the Devices tab, you can see all connected devices. There are the following three
columns:
• Device id: the internal name of a device.
• Device name: the name assigned to a device.
• Reporting name: the name used in reports for a device.

If you click a device, you can customize the reporting name of the device in a right-hand
side panel. From firmware version 2.20 onwards, you can customize also other device-
specific reporting attributes.
Use the Refresh button to refresh the device list.
 Reporting 121

 Parameter history logging tab

The Parameter history logging tab shows the drive signals to be reported. By default all
signals are checked for changes daily. Only changes are saved and reported to the SD
card.

The tab contains the following components:

• Refresh button refreshes the contents of the parameter list.
• Interval selection drop-down list shows the logging intervals.When you select an
interval, the contents of the parameter list are updated. The following intervals are
available:
• All
• Minute
• 5 minutes
• Hour
• Day
• Monitor.
• Capacity shows the number of parameters in the selected interval. The maximum
number of allowed monitored parameters per time interval are as follows:
• 1 minute – max. 100 parameters
• 5 minutes – max. 500 parameters
• 1 hour – max. 1000 parameters
• day – max. 10000 parameters
• monitor – max. 20 parameters.
122 Reporting

• Parameter list shows all parameters in the selected interval. Multiple parameters can
be selected at the same time. If at least one parameter is selected, the parameter
properties panel is shown. The following columns exist:
• Parameter name
• Parameter group
• Device name
• Device id
• Interval.
• In the Parameter properties panel you can customize the logged signal name and
logging interval and select that logging is done either always or only when the signal
value has changed.

There are different ways to select multiple parameters:

• With the check boxes on the left of the parameters; add or remove parameters one by
one by clicking the check boxes
• To cancel the selection, click anywhere else in the row.
• With the Ctrl key; press the Ctrl key and click the rows you want to select.
• With the SHIFT key; hold down SHIFT and click the first and last rows of the selection.
To change the interval of parameters, select the parameters, choose the appropriate
interval from the drop-down list and click Apply changes. If you select multiple
parameters, you cannot edit the signal name and the signal logging history is not shown.
The signals are logged only if their values have changed. If the Log on when changed
check box is unchecked, the values are logged even if they have not changed.
 Reporting 123

 Reported data tab

To see all sent reports and those errors that may have occurred after reports have been
created and sent, go to Reports –> Reported data. The reports are sent to the email
address defined in section Creating an email report.

 Configuration events tab

To see all the modifications made to reporting settings, go to Reports –> Configuration
events. The events can be filtered and sorted.
124 Reporting
 Tools 125

14
Tools

What this chapter contains

This chapter explains how to manage NETA-21 firmware, factory settings and software
packages and introduces other useful tools.

Tool firmware
The Tool firmware tab (Settings –> Tool settings) shows the installed firmware version
of the NETA-21 and enables to update the firmware of the NETA-21.

Note: To enable the NETA-21 firmware updates, an SD card with a minimum of 200 MB
free space must be inserted into the NETA-21.
126 Tools

The Tool firmware tab contains the following components:

• Save button saves the firmware update settings to the NETA-21.
• Reset button discards all changes made to the firmware update settings.
• Upload button opens a file browser for sending a firmware file to the memory card.
Firmware files to be uploaded must have the following name format: FMZAAvrr.NTU,
where vrr represents a 3-digit version number (letters can be in upper or lower case).
• Reboot tool button reboots the NETA-21, which triggers the software update if new
and selected firmware upgrade exists in the memory card. You are prompted to reboot
the NETA-21 after clicking the Reboot button.
• System information panel shows tool-specific information. The panel contains the
following fields: Remote monitoring tool type, Remote monitoring tool serial number,
Installed software, Software build version, MAC1 address and MAC2 address.
• Tool firmware updates panel shows all available firmware updates on the SD card.
The changes are saved and firmware installation settings are modified when you click
the Save button. The unchecked firmware files whose version number is not greater
than the version number of the currently installed firmware file are blacklisted and not
installed during the next reboot.
• Firmware column shows the file name of the file. The column contains also a check
box for defining whether the firmware update should be installed in the next reboot (if
the file is not checked, then NETA-21 does not try to install it). The check box is
disabled if the firmware is older than the current firmware or if it is the current firmware.
• Description column shows the status of the firmware update. The following conditions
may be seen:
• Old firmware is shown if the currently installed software is newer.
• Currently installed is shown if the file version equals to the currently installed
software.
• Non-installable is shown if the running OS version is factory-loaded (FMZALvrr)
and the same version as the update package (FMZAAvrr).
• Installation failed is shown if the number of the running OS version is smaller and
updating has failed.
• Not chosen to be installed is shown if the number of the running OS version is
smaller and the file is not checked.
• Install on next reboot is shown if the number of the running OS version is smaller
than the number of the currently installed firmware version. The NETA-21 tries to
install the OS during the next reboot.
 Tools 127

Factory tools
Factory tools tab provides an option to reset the NETA-21 to factory settings, and an
option to disable (or keep enabled) the factory support account.

The Factory tools tab contains the following components:

• Save button saves the settings. If the restore factory settings check box is selected,
you are prompted to reboot the NETA-21.
• Reset button discards all changes made to the settings.
• Export button exports the settings to a local file.
• Import button imports the settings from a file to the UI.
• Reboot button reboots the NETA-21.
• Enable factory login is a check box for enabling or disabling the factory user. Each
NETA-21 has an individual factory user account for remote service and support
purposes. You can disable the factory user account completely.
Note: The factory user account can be disabled if strict security is needed, but the
deletion of the account may affect the warranty of the NETA-21 and remote support
options. If you disable the factory login, you will also disable the SSH service at TCP
port 22. The NETA-21 contains a factory support account for the web UI and for SSH
remote connections. Factory account passwords are unique to each NETA-21.
• Restore factory settings is a check box for removing all user data from the NETA-21
during the next reboot.
128 Tools

Packages
The Packages tab enables to install and uninstall packages from the NETA-21. All core
packages are filtered from the list so that you cannot uninstall any vital packages from the
NETA-21.
You must have a Tool admin role (administrator) to access this view. This tab can only be
used to install signed packages with an IPS file extension.

The Packages tab contains the following components:

• Refresh button refreshes the package list.
• Install button opens a file selector for an IPS package. After a file has been selected,
the file is sent to the NETA-21 and installed. IPS packages are signed extra software
packages provided by ABB.
• Uninstall button is enabled only if a package has been selected from the package list.
When you click the button, you are asked to confirm the uninstallation before the
NETA-21 starts uninstalling the package.
• Package list shows all installed packages in the NETA-21 excluding all packages that
are necessary to the functioning. The package list contains the following columns:
Name, Version and Installed.

Using ABB IP Configuration Tool

ABB IP Configuration Tool detects all the NETA-21 remote monitoring tools in the network.
The tool can be downloaded separately from www.abb.com, but it also comes bundled
with ABB Control Builder Plus, the IEC 61131-3 programming environment for ABB PLCs
and drives.
Use the tool, for an example, when you no longer know the IP address of the NETA-21 or
when you do the initial set-up.
If you have the ABB Control Builder Plus 2.3.0 build 312 or newer installed, do as follows:
 Tools 129

1. Launch the tool from Tools –> IP-Configuration.

2. Start the scanning process by clicking the Scan button:

Note: If no devices are found, make sure that your firewall does not interfere with the
scanning process. Disable your firewall and try again.
All devices found during the scanning process are presented in a table where each
device is in a separate row. In addition to the IP addresses of the device you can also
see the MAC address, device name, serial number and device ID information.
130 Tools

In older Control Builder Plus 2.3.0 builds (for example build 252), ABB IP Configuration
Tool is a separate program. Go to Start –> ABB –> ABB IP Configuration. However, the
older version of ABB IP Configuration Tool gives the same information:
 Backup and restore 131

15
Backup and restore

What this chapter contains

The backup and restore function enables the replication of the NETA-21 settings to
another similar type of remote monitoring tool. There are two main backup types: full
system backup and backup of the selected settings only.

Backing up the NETA-21

1. Go to Settings –> Backup and restore and select the backup type.

Note: You must have an SD/SDHC card installed into the SD slot to create a backup.
The SD card must have a minimum of 200 MB free space to enable the
backup/restore functions. Backup and restore files are stored in the BACKUP folder on
the SD card.
Create backup creates a backup according to the selected backup type.
132 Backup and restore

Full system backup enables a full system backup of the NETA-21. The NETA-21 is
rebooted before the backup file can be downloaded. After the NETA-21 goes back
online, you must log on to the NETA-21. After you have logged on to the NETA-21, the
Backup tab is shown and the NETA-21 starts sending the backup file to the PC.
Settings backup enables a backup of selected data categories. You can select the
following data categories:
• Device information
• Device interface settings
• Network service settings
• Users
• Locale settings
• User interface settings
• Logging settings
• Reporting settings
2. Click the Create backup button.
The following dialog box appears.

If you have chosen the Settings backup type, the Making backup pop-up window
appears.

Note: If a reboot is required after a backup has been created, log on to the NETA-21 to
enable downloading when the system is back online.
 Backup and restore 133

Restoring the NETA-21

1. Go to Settings –> Backup and restore –> Restore.

The Restore file function restores a selected file. If restoring requires rebooting (full
system restore), you are prompted to reboot the system. If you choose to reboot the
NETA-21, the reboot view is shown. When the server goes back online, you are
redirected to the Login window and eventually back to the Restore tab.
To restore the files stored in the SD card, select the Select an existing file from the
memory card check box.
2. Click the Restore file button.
The following dialog box appears.

If the file is a Settings backup file, a progress dialog box appears showing the status of
the settings importation.

Note: If the restore file contains different network interface settings (for example IP
addresses for Ethernet interfaces), the connection to the web UI can be lost after the
restore function has been started. The new IP address settings depend on the file restored
to the NETA-21.
134 Backup and restore
 Memory card 135

16
Memory card

What this chapter contains

This chapter describes the tabs under Memory card.

Using the memory card

To observe and manage the data on the memory card, go to Settings –> Memory card.
Use the memory card for collecting, for example, log files, backup files, device manuals
and restore archives.

Memory card status tab

The Memory card status tab shows actual data about the memory card: status, access
type and space status.
136 Memory card

In general, the toolbar contains the following buttons:

• Refresh button refreshes the memory card data in the current interface.
• Add content button adds the portals: Status, Memory card control and Events.
• Save layout button stores the current layout settings to the NETA-21 memory.

File browser tab

The File browser tab shows the files in the memory card. You can see this tab only if your
role is Tool admin.

In general, the toolbar contains the following buttons:

• Refresh button refreshes the list of files in the current folder.
• Parent directory button goes to the parent folder.
• Open button opens the selected file.
• Add… button copies a file from the PC to the memory card.
• Remove button deletes the selected file or folder (only an empty folder can be
deleted).

Autoinst tab
The Autoinst tab works the same way as the File browser tab but it uses the “autoinst”
folder as a root folder in the memory card.

Backup tab
The Backup tab works the same way as the File browser tab but it uses the backup
folder as a root folder in the memory card.
 Memory card 137

Report tab
The Report tab works the same way as the File browser tab but it uses the report folder
as a root folder in the memory card.

Restore tab
The Restore tab works the same way as the File browser tab but it uses the restore
folder as a root folder in the memory card.
138 Memory card
 Diagnostics and troubleshooting 139

17
Diagnostics and troubleshooting

What this chapter contains

This chapter explains how to trace faults with the status LEDs on the NETA-21 and the
NEXA-21.

LED indications
The NETA-21 is equipped with 13 bi/tricolor diagnostic LEDs. The NEXA-21 is equipped
with four bi/tricolor diagnostic LEDs. The LEDs are described below.
140 Diagnostics and troubleshooting

 LED indications of the NETA-21

Name Color Function

USB Off No USB mass storage devices attached

Green USB mass storage device attached and mounted.

Blinking green Device attached, initialization in progress

Yellow Device can be removed.

Red Unidentified error when settings are imported from an USB memory
device.

Blinking red Initialization failed.

Unsupported file system on a USB stick.
Only FAT file systems with 8.3 character filenames are supported.
Basically, NTFS-formatted USB sticks and external hard disks are not
supported.

EXT Off No NEXA-21 connected

Green NEXA-21 found and initialized

Blinking green NEXA-21 support is being initialized (when the NETA-21 boots up)

Red NEXA-21 malfunctions

Blinking red NEXA-21 not supported

SD Off No SD/SDHC card

Green Card attached and taken into use

Blinking green Card attached and initialization in progress

Yellow Card can be safely removed

Blinking yellow Card attached, removal in progress

Blinking yellow Together with the blinking red STAT LED: System waits for
confirmation of reboot operation or network override

Red Card error, for example write protection prevents from writing data to the
card

Blinking red Card initialization failed.

Unsupported card type, for example, SDXC (extra capacity) cards and
MMC cards are not supported.

PNL 1/ Off No devices (no wire) connected to the PNL port

PNL 2
Green All devices connected, identified and commissioned

Blinking green Manual or automatic discovery of devices in progress

Yellow Communication OK, but device connectivity limited.

All devices are ready to be unplugged/disconnected.

Red Communication error caused the panel port network initialization to fail.
Unknown device in the network, or something is interfering the network
and preventing proper detection of monitored devices.

Blinking red Unsupported device is found in the network, or there are too many
devices in the network to be monitored
 Diagnostics and troubleshooting 141

Name Color Function

PC ETH 1 Off PC not connected.

If an Ethernet cable is connected to the PC ETH 1 port but no one uses
the NETA-21, the LED remains blank.

Green Connection set up and in operation, for example, DHCP is active and at
least one PC has got an IP-address

1/2-second • NETA-21 provides IP addresses for local devices.

blinking green Activate the DHCP server mode by pressing the SD RJ45 button for
five seconds.
• When a PC is connected and the NETA-21 has provided an IP
address for it, the LED turns steady green.
Note: The DHCP server functionality remains enabled until the NETA-21
is restarted or until the DHCP server is disabled in the web UI
(Settings –> Network interfaces –> Ethernet 1).

1-second At least one user has been logged on to the user interface
blinking green

Blinking yellow Factory-level access/operation.

Firmware update in progress.
Note: System status (STAT LED) blinks during the firmware update.

PWR Off Power off

Green Power on

Yellow Timed power off or standby.

NETA-21 can go to the standby mode as a protective measure (eg, if the
environmental temperature is too high).
To wake up the NETA-21, press the SD RJ45 button.

STAT Green System in operation, OK

Yellow System starts up, services not yet fully operational

1/4-second System waits for a confirmation of the reboot operation or network

blinking yellow override.
• If you reboot the NETA-21 by pressing the reset button for 5 seconds
when the NETA-21 is running, the STAT LED starts blinking. Confirm
the reboot operation by pressing the SC RJ45 button. If you do not
confirm the reboot operation, it stops after a 1-minute delay.
• You can override the network settings by pressing the SD RJ45 button
for 10 seconds when the NETA-21 powers up. If you keep pressing
the button for about 20 seconds, the STAT LED starts blinking, which
indicates that you can release the button. If you do not release the SD
RJ45 button within one minute (or if the button is locked to the “ON”
position), the default network settings are not restored.

1-second Firmware update in progress

blinking yellow

Blinking red Error occurred during the start-up of the NETA-21.

If the start-up fails, the NETA-21 restarts itself automatically after a few
seconds. During the reboot operation, all LEDs excluding the PWR LED
flash before the STAT LED turns yellow again.
Note: If the yellow STAT LED and blinking red STAT LED alternate and
the STAT LED does not turn green, the start-up of the NETA-21 fails
continuously. Try resetting the NETA-21 to factory settings.

MON Blinking green NETA-21 sends data (eg, email) to an external destination.

Blinking red NETA-21 fails to send data (eg, email) to an external destination. Log on
to the web user interface and go to Reports –> Events for error details.
142 Diagnostics and troubleshooting

 LED indications of the NEXA-21

Name Color Function

PWR Off NEXA-21 not controlled by the NETA-21 or the NETA-21 boots up

Green NEXA-21 detected by the NETA-21 and the NEXA-21 turned on

STAT Green System in operation, OK.

DDCS drives commissioned.
Communication with drives OK.

Yellow System reboots, the NEXA-21 temporarily out-of-order

Blinking yellow Limited connectivity.

Devices not found.

Red Internal error.

DDCS network not physically OK, or no devices detected.

Blinking red Incompatible device in DDCS.

NEXA-21 has lost connection to a configured device.
Note: DDCS is running.

RX Off Not receiving data

Yellow Receiving data

TX Off Not transmitting data

Yellow Transmitting data

Troubleshooting
Problem Cause Solution
The STAT led of the NEXA-21 DDCS devices are not detected. Do as follows:
turns red after the NETA-21 has Check that the DDCS wiring is
been powered up. connected the right way around.
Log on to the NETA-21 web user
interface.
Go to Settings –> Device
interfaces, select the ddcs tab
and click Rescan devices.
The newly connected devices do Automatic rescanning is done only EITHER: Disconnect wires for 1
not appear in the UI. if all devices per interface have minute and then reconnect.
been disconnected for 1 minute or OR: In the UI, go to Settings –>
longer. Device interfaces, select the
interface specific tab, and click
button Rescan devices.
The disconnected old devices Disconnected devices must to be The solution depends on the
remain in the UI and do not manually removed. An automatic device interface. Try one of the
disappear. removal would affect customized following:
device settings, such as reporting 1. Go to Settings –> Device
settings. interfaces and select the
specific device interface. Click
button Rescan devices.
2. If devices still reside in the UI,
go to the front page of the
disconnected device. Check the
Device control panel and click
the Remove device button if
such a button is available.
 Diagnostics and troubleshooting 143

Problem Cause Solution

Web pages behave erratically or The web browser cache contains Try refreshing the whole page. Try
the login is prevented after the tool an old version of the user interface. pressing the shift key on the
firmware update. keyboard during refreshing, to
reload all script files. If that does
not help, clear all temporary
internet files or the cached web
content using browser specific
menus, and try to log on to the
NETA-21 again.
When the web page is zoomed The content zooming with touch Zoom to the desired level and tilt
with a tablet or mobile phone only screen devices is not fully the phone/tablet screen (90
part of the screen area is usable. supported. degrees to the horizontal or vertical
position) to readjust screen frames.
144 Diagnostics and troubleshooting
 Technical data 145

18
Technical data

What this chapter contains

This chapter contains the technical data of the NETA-21 and the NEXA-21.
146 Technical data

Hardware
 Enclosure of the NETA-21

98 54.2
[3.9] [2.1]

[1.5]
39
120
[4.7]

124
[4.9]

[4.5]
90
[1.3]
34

58
[2.3]
 Technical data 147

 Enclosure of the NETA-21 with the NEXA-21

98 79
[3.9] [3.1]

[1.5]
39
120
[4.7]

124
[4.9]

[4.5]
90
[2.3]
59

58
[2.3]
148 Technical data

 Technical data of the NETA-21 and the NEXA-21

Mounting On a 35-mm / 1.4-inch DIN rail

Degree of protection IP20

Ambient conditions Applicable ambient conditions specified for the drive in its manuals are in effect.
• Operating temperature: -5…+60 °C / -23…+140 °F (free air circulation)

Indicators 9 + 4 bi/tricolor LEDs

Connectors Power supply input (X1)

• Signal level: 10 … 30 V DC, max. 2 A (typical: 200mA @ 24 V / 500 mA @ 12 V)
• Connector type: Shrouded header for the wire plug, 2 pins, pitch 5.00 mm / 0.19
inch
Panel bus port 1 (PNL 1) and 2 (PNL 2)
• Signal level: EIA-485
• Communication protocol: Panel bus over EIA-485
• Cable type: Ethernet CAT5, straight
• Connector type: Shielded 8P8C modular jack (RJ45)
• Maximum segment length: 100 m / 328 ft
Ethernet port 1 (ETH 1) and 2 (ETH 2)
• Media: 10Base-T / 100Base-TX (10 Mbit/s or 100 Mbit/s)
• Cable type: Shielded twisted pair (STP), both straight-through and crossover
cables are supported (HP Auto-MDIX).
• Connector type: Shielded 8P8C modular jack (RJ45)
• Termination: Internal
• Maximum segment length: 100 m / 328 ft
EIA-232 Port (X2)
• Physical layer: EIA-232, galvanic isolated
• Connector type: D-sub 9-pin male
EIA-485 Port (X3)
• Medium: Shielded twisted pair cable, impedance 100…150 ohm
• Serial communication type: Asynchronous, half-duplex RS-485
• Physical layer: EIA-485, galvanic isolated
• Communication protocol: Modbus
• Connector type: Shrouded header for the wire plug, pitch 5.00 mm / 0.19 inch
• Maximum length: 1200 m / 3 937 ft
SD/SDHC connector
• Supports up to a 32-GB SD/SDHC card
USB host ports
• PHY Interface: USB2.0
• Connector type: Shielded USB Type A
Fiber optic transmitter/receiver DDCS
• Media: Fiber optic cable
• Protocol: Distributed Drives Communication System (DDCS)
• Connectors: Dark grey – receiver; grey – transmitter

Power supply • Primary power supply input: 10…30 V DC, max. 3 A

• Secondary power supply input: AC/DC 24 V ± 10%, max. 1 A (rms). For
redundant power supplies via extension modules.
• Power supply output: 5 V, 700 mA for external option modules. Short circuit
protected.
 Technical data 149

General • Estimated minimum lifetime: 100 000 h

• Battery replacement interval: 5 years at 25 °C / 77 °F
• Complies with EMC standards IEC 61000-6-2 and IEC 61000-6-4
• All materials are UL-approved
150 Technical data
Further information
Product and service inquiries
Address any inquiries about the product to your local ABB representative, quoting the type
designation and serial number of the unit in question. A listing of ABB sales, support and
service contacts can be found by navigating to www.abb.com/searchchannels.

Product training
For information on ABB product training, navigate to www.abb.com/drives and select
Training courses.

Providing feedback on ABB Drives manuals

Your comments on our manuals are welcome. Go to www.abb.com/drives and select
Document Library – Manuals feedback form (LV AC drives).

Document library on the Internet

You can find manuals and other product documents in PDF format on the Internet. Go to
www.abb.com/drives and select Document Library. You can browse the library or enter
selection criteria, for example a document code, in the search field.
Contact us

3AUA0000096939 Rev C (EN) 2013-07-12

www.abb.com/drives
www.abb.com/solar
www.abb.com/windpower
www.abb.com/drivespartners