Scribd
Upload
102 views

Manual K Universal

To reset the system to factory default settings, power off the device, press and hold the # key while powering on, and release the # key after hearing two ticks. Registered users will not be deleted during a factory reset. The device uses a light dependent resistor as an anti-tampering alarm that will activate if the keypad cover is removed. The detailed programming guide outlines how to perform settings like changing codes, adding/deleting users, and setting the access modes (card only, card and PIN, or card or PIN).

Uploaded by

Irvin Yair Sabillón López
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
102 views

Manual K Universal

To reset the system to factory default settings, power off the device, press and hold the # key while powering on, and release the # key after hearing two ticks. Registered users will not be deleted during a factory reset. The device uses a light dependent resistor as an anti-tampering alarm that will activate if the keypad cover is removed. The detailed programming guide outlines how to perform settings like changing codes, adding/deleting users, and setting the access modes (card only, card and PIN, or card or PIN).

Uploaded by

Irvin Yair Sabillón López
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

a.

To Reset to Factory Default


a p 0 wer off
· p ss and hold # key whilst powering on
b. re . #k . b
c. On hearing tick twrce release ey, system 1s ack factory settings now
Registered users won ·t be deleted when reset to factory default

9.Anti Tamper Alarm


The unit uses a LDR (light dependent resistor) as an anti tamper alarm. lf the keypad is removed from
the cover then the tamper alarm will operate.

1o.sound and Light indication

Operate Status LED Light Color Buzzer

Standby Flash Red Slow

Keypad Short Tick Once

Operation Successful Green Long Tick Once

Operation Failed Short Tick 3 Times

Entering into Programming Red Long Tick Once

Programmable Status Orange

Exit Programming Flash Red Slow Long Tick Once


'

Door Opening Green Long Tick Once

Alarm Flash Red Quick Alarming

11. Detailed Programming Guide


11.1 User Settings
To enter the programming mode
!1 IM~~ oode] l~]
999999 is the default factory master code

To exit from the programming mode ...f~"l


Note that to undertake the following programming the master user must be logged in
O New code # New code #
To change the master code The master code can be 6 to 8 digits long

Setting the working mode: 3 O # Entry is by card only


s et valid card only users 3 1, # Entry is by card and PIN together
Set valid card and PIN users 3 2 # Entry is by either card or PIN (default)
Set valid card or PIN users

To add a user in either card or PIN mode, i.e. in the 3 2 # mode. (Default setting)

1 User ID number # PIN #


The ID number is any number between 1 & 2000. The
PIN is any four digits between 0000 & 9999 with the
exception of 1234 which is reservad. Users can be
To add a Pin user
added continuously without exiting programming mode
as follows:
1 User ID no 1 # PIN # User ID no 2 # PIN #

2 User ID number #
To delete a PIN user Users can be deleted continuously without exiting
programming mode

To change the PIN of a PIN user


(This step must be done out of * ID number # Old PIN # New PIN # New PIN #
programming mode)
1 - - - - - - - - - - - - -·->--- ------ - - - -- - - -- - - - - - - - !
To add a card user (Method 1) 1 f~ead c.ard #
This is the fastest way to enter cards, Cards can be added continuously without exiting
user ID number auto generation programming mode

To add a card user (Method 2)


This is the alternative way to enter
cards using User ID Allocation. In this 1 ID number # Read card #
method a User ID is allocated to a card. User can be added continuously without exiting
Only one user ID can be allocated to a programming mode
single card

To add a card user (Method 3)


Card number is the last 8 digits printed 1 Catd number #
on the back of the card,user ID number User can be added continuously without exiting
auto generation programming mode

To add a card user (Method 4)


In this method a User ID is allocated 1 ID number # Card number #
to a card number. Only one user IO User can be added continuously without exiting
can be allocated to the card number programming mode
" - - - - - - - - L_ _ __ _

You might also like