Scribd
Upload
291 views

Designed KSK Checked SN Approved SN Date 11.4.20: Design of Basement Retaining Wall Shuttering Refrence Standrd

This document provides design details for the shuttering of a basement retaining wall. It specifies design loads, material properties, and calculations to check the adequacy of the proposed aluminum and steel beams to support the wall formwork. The analysis confirms that the maximum bending moments, shears, reactions and deflections of the proposed structural members are within permissible limits based on the specified design loads and material strengths.

Uploaded by

Senthilkumar K
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
291 views

Designed KSK Checked SN Approved SN Date 11.4.20: Design of Basement Retaining Wall Shuttering Refrence Standrd

This document provides design details for the shuttering of a basement retaining wall. It specifies design loads, material properties, and calculations to check the adequacy of the proposed aluminum and steel beams to support the wall formwork. The analysis confirms that the maximum bending moments, shears, reactions and deflections of the proposed structural members are within permissible limits based on the specified design loads and material strengths.

Uploaded by

Senthilkumar K
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 4

DESIGNED KSK

CHECKED SN
APPROVED SN
DATE 11.4.20

DESIGN OF BASEMENT RETAINING WALL SHUTTERING

REFRENCE STANDRD

1. BS 5975:2008 (Code of practice for temporary work and procedure


and permissible stress)
2. Formwork guide to good practice: 1995(by concrete society)
Loads:
Dead load - design concrete pressure is taken as 50KN/m^2
Material Properties
Aluminium beam
Permissible bending moment capacity = 4.4 KNm

Permissible shear capacity = 28.8 KN

Stell water SR2 U100

Safety factor = 2

Minimum effective bearing length = 100 mm

Allowable tension stress Prc = 180 N/mm2

Elastic section modulus Zrex = 82.4 Cm3

Permissible Bending moment capacity = 14.832 KNm

Permissible shear capacity = 129.6 KN

Design of Wall form work

Wall form work height = 2.9 M

Dead load design concerte pressure = 50 KN/m2

(Ref. 'Formwork a guide to good practice')


Material: Finnish 18mm Wisaform Special Birch 13 ply overlaid
Face grain - Parallel to EI = 3.28 kN/m2/m
Thickness (t) = 17.6 mm

Weight = 12.7 Kg/m^2

Wall formwork- Load duration factor = 1.5

Applied load = 50 KN/m^2

Span(L) = 330 mm

Support width = 50 mm

Result : (Permissible values in braclet)


Load W = (Applied Load X L) = 16.5 KN/m

0.095WL = 0.517275 KNm


Maximum bending mement

Max shear 0.525((L-b-t)/L)W = 6.888 KN

Max reaction for 1.0m width = 16.5 KN

Self deflection 0.0066((WL/3)/EI) = 0.110670732 mm < 2mm safe

Deflection range 0.0068((WL/3)/EI) = 0.11402439 mm < 2mm safe

Secondary Beam - GT 24 Girder

A = 96 cm4 E = 10000 N/mm2


I = 8000 cm4 W = 667 cm3
Spacing = 330 mm

Design concrete pressure = 50 KN/m2

Applied load = 16.5 KN/m

Form work ht = 3 m

Span (L) = 1.2 m

Aluminum Beam
Allowable bending moment = 4.4 KNm
Allowable Shear = 28.8 KN

Safety Factor (2:1) (On ultimate) = 16.5 KN/m

Result: Permissible load capacity & member in brackets

Maxiumn saging BM = 1.98 < 4.4 safe

Maximum hogging BM = 2.376 < 4.4 safe

Maximum shear = 21.78 < 28.8 safe

Permissible deflection = 2.4 mm

Deflection = 0.00030 mm < 2.4 safe

Max. Reaction from secondary beam = 21.78 KN

ondary beam spacing = 330 mm

Primary Beam (Steel waler SRZ U 100)


Load acting on primary beam/m = 66.00 KN/m

A = 24.3 cm2 E = 210000 N/mm


4 3
I = 408 cm W = 81.1 cm

Spacing of two support = 1.22 m


Results: Permissible load capacity of members in brackets

Maximum Sagging Bending Moment = 3.5937 < 14.83 safe

Maximum Sagging Bending Moment = -1.188 < 14.83 safe

Maximum Shear = 21.78 < 129 safe

Maximum reaction = 39.6 < 258 safe

Permissible Deflection = 2.44

Sag deflection = 0.00023886 < 2.44 safe

You might also like