Scribd
Upload
439 views

Nodemcu Esp8266: Details and Pinout

The document discusses the NodeMCU ESP8266 development board, including its components, pinouts, and how to program it. It is formed from an ESP-12E board containing an ESP8266EX microchip. Not all pins can be used for digitalWrite, digitalRead, analogWrite, or analogRead. The document provides the pin numbers that should be used and demonstrates an example blink program. It also details the behavior of pins after boot and which pins are inputs/outputs.

Uploaded by

Sandy M S
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
439 views

Nodemcu Esp8266: Details and Pinout

The document discusses the NodeMCU ESP8266 development board, including its components, pinouts, and how to program it. It is formed from an ESP-12E board containing an ESP8266EX microchip. Not all pins can be used for digitalWrite, digitalRead, analogWrite, or analogRead. The document provides the pin numbers that should be used and demonstrates an example blink program. It also details the behavior of pins after boot and which pins are inputs/outputs.

Uploaded by

Sandy M S
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

instructables

NodeMCU ESP8266: Details and Pinout

by Fernando Koyanagi

Today, we will talk about ESP8266 pinning, or in As I program more with Arduino IDE, I practically see
other words, NodeMCU. Personally, I really like this the NodeMCU as an Arduino. However, I must
component, as it already comes with USB input. But emphasize these devices have differences, especially
it is important to explain that the NodeMCU is formed concerning the pinning. If you watched the ESP32
by an ESP12E, which still has an ESP8266EX inside video entitled “Internal Details and Pinout,” you’ve
it. Thus, we’ll learn the correct pin identification by learned there are pins that can’t be used, or that are
doing the following: looking at the NodeMCU reserved for certain things. So I want to do something
datasheet, knowing which of these pins work with useful here related to this, but this time with
digitalWrite, digitalRead, analogWrite, and ESP8266.
analogRead, and understanding the boot more
thoroughly.

https://youtu.be/slKGGrPDNpk

Step 1: NodeMCU Devkit 1.0

The term NodeMCU usually refers to the firmware, while the board is called Devkit.

NodeMCU Devkit 1.0 consists of an ESP-12E on a board, which facilitates its use.

It also has a voltage regulator, a USB interface.

NodeMCU ESP8266: Details and Pinout: Page 1


Step 2: ESP-12E

The ESP-12E is a board created by AI-THINKER, which consists of an ESP8266EX inside the metal cover.

NodeMCU ESP8266: Details and Pinout: Page 2


Step 3: ESP8266EX

Made by Espressif, this microchip has integrated WiFi and low-power consumption.

Processor RISC Tensilica L 106 32bit with a maximum clock of 160 MHz

Step 4: NodeMCU 1.0 ESP-12E Pinout

NodeMCU ESP8266: Details and Pinout: Page 3


Step 5: ESP-12E Pinout

I want to emphasize that NodeMCU and ESP-12E are not the same things. In the case of the ESP-12E, the
recording uses the serial, the UART. In NodeMCU, this is performed by the USB.

Step 6: And After All This, What's the Number to Put When Programming?

Use the number that is in front of the GPIO or the constants A0, D0, D1, D2, D3, D4, D5, D6, D7, and D8.

Step 7: Boot

We put the oscilloscope at the tip of each pin. This allows us to find, for example, that when we turn on the
NodeMCU, its pins are not all the same. Some are up and others down, by default. See the comments on the
behavior of each post after the boot in the image below.

NodeMCU ESP8266: Details and Pinout: Page 4


Step 8: Constants That Are Already Predefined

NodeMCU ESP8266: Details and Pinout: Page 5


Step 9: Blink Example

In this example, we connected an LED on port D5, which is GPIO14. So the options are as follows:

//O led está no GPIO14


#define LED 6
//ou usar a constante D5 que já está definida
//#define LED D5

void setup() {
pinMode(LED, FUNCTION_3);
}

void loop() {
digitalWrite(LED, HIGH);
delay(1000);
digitalWrite(LED, LOW);
delay(1000);
}

NodeMCU ESP8266: Details and Pinout: Page 6


Step 10: INPUT / OUTPUT

When performing INPUT and OUTPUT tests on the pins, we obtained the following results:

digitalWrite did NOT work with GPIOs 6, 7, 8, 11, and ADC (A0)

digitalRead did NOT work with GPIOs 1, 3, 6, 7, 8, 11, and the ADC (A0)

analogWrite did NOT work with GPIOs 6, 7, 8, 11, and ADC (A0) (GPIOs 4, 12, 14, 15 have
hardware PWM, and the others are by software)

analogRead worked only with the ADC (A0)

6, 7, 8, 11 do NOT work for the above four commands

Step 11: PDF

Download the PDF.

NodeMCU ESP8266: Details and Pinout: Page 7

You might also like