STORAGE TANK SPECIFICATION Sheet 1 of  1

ng s n ts
ts  .
  o
   N
 .
Project No. 1952.000   v
  e
   R

1 Service : CRUDE OIL Storage Equipment No. : T-400 & T-405

2 Location : Unit : Kirwin Design Engineer :
3 Manufacturer : Model : Mfr Ref. No. : No. Req'd : Two
4 P&ID No. PID115-EPF-01-112A1 Plot Plan No. : Other Ref. Dwg No. :
5
6
7
8 M
9  A P G
10
11
12
13 50.00 Ft
14 H
15 32.00 Ft 48" X 48"
16 FLUSH
E CLEANOUT E
17
K
18
19 L F D
20
21
22 N1 N2 J I
23
24 Shell Diameter : 50.00 Feet Shell Height : 32.00 Feet Nominal Volume : 11,191 Barrels
25 Roof Type : Cone Bottom Floor Type: Sloped
26 OPERATING/DESIGN DATA NOZZLES/CONNECTIONS
27 Fluid Stored : CRUDE OIL Sp. Gr. : 0.7900 Mark Service Qty Size Rating  Face
28 This Tank Service is considered: Cyclic  A Roof Manway 2 24" 150# F. F.
29 Vapor Pressure @ Max. Operating Temperature 5.5 psia E Shell Manway 2 24" 125# R. F.
30 Flash Point (Closed Cup) : ºF Operating Design F  Flush Cleanout MW 1 48"x48" 125# R. F.
31 Negative Pressure oz/in.2 0.00 0.50 G Stilling Vent 1 6" 125# F. F.
32 Positive Pressure psig 1.00 2.00 H Temperature Indicator  1 1" 150# L. J.
33 (Hydro)test Pressure expressed in Psig ---- I Outlet Nozzle 1 8" 150#  API
34 Minimum Fluid Temperature ºF -25 J Fill Nozzle 1 10" 150# L. J.
35 Maximum Fluid Temperature ºF 200 K Mixer Manway 1 30" 150# F. F.
36 Emergency Vacuum Design ?  Yes Set @ 0.0.3 oz/in.2 L Water Draw Nozzle 1 4" 150# R. F.
37 METALLURGY M Top Center Vent 1 8" 150#  API
38 Component Material CA, in. Remarks N1 Sample Tap 1 3/4" 150# R. F.
39 Shell & Bottom 57370 0.1250 Normalized N2 Sample Tap 1 3/4" 150# F. F.
40 Roof  16 Grade 5 0.1250 Normalized P Roof Nozzle 1 4" 150# L. J.
41 Lining/Coating D Spare 1 2" 150#  API
42 150#  API
43 Stress Relieve ?  Yes for: 150#  API
44 CONSTRUCTION/FABRICATION
45 Code (as appl.): API 650 LATEST EDITION Internals (attach separate sheet, as req'd): Others:
46 Design Specifications: Sump
47 Tank Insulation ? No Thickness : in. Seismic Zone 3 Design Wind Velocity 100 mph
48 Insulation Type: Hot Radiograph 85 % Inspection Req'd ?  Yes
49 Fireproofing ?  Yes Paint Spec. EmptyTank W eight lb Full of W ater   lb
50 Remarks
51 1. Items marked with an asterisk ( *) to be completed by Vendor/Fabricator.
52 2. Fixed cone roof with internal floating roof.

Approvals
Rev Date Description By Chk.  Appr. Rev Date Description By Chk.  Appr.
0 For Inquiry
 Art Montemayor API 650 Storage Tank March 12, 2002
Rev: 0
API 650 Design Calculations

D = Normal tank diameter , in feet 50.00

H = depth of tank , in feet 32.00

Shell
Shell Desi
Design
gn : FROM
FROM ( BOTT
BOTTOM
OM COUR
COURSE
SE)) PLA
PLATE TO
TO (TOP
(TOP COU
COURS
RSE)
E) PLA
PLATE
TE

td = 2.6(D)(H -1)(G)/Sd= 0.174 in. Wall Thickness

Miniumum shell thickness, in inches, t d = td / tt = 2.6(D)(H-1)/(St)
td = 0.224 in. (Includes Corrosion Allowance)

G = design Specific gravity of liquid 1

Sd = allowable Stress for Design condition 23,200
E = joint efficiency 0.85%
St = allowable
allowable stress 516-60 Hydro Test 24,900
CA = Corrosion Allowance 0.0625

For First Course (Bottom) 516-60 Plate 0.236

td = 2.6(D)(H -1)(G)/Sd = 0.189

td =td / tt = 2.6(D)(H-1)/(St) =
td = Miniumum shell thickness, in inches = 0.230

D = Normal
Normal tank diameter , in feet = 50.00
H = depth of tank
tank , in feet = 32.00
G = design Specific gravity of liquid = 1
Sd = allowable StrStre
ess fo
for De
Design co
condition 21,30
,300
E = joint efficiency 0.85%
St = allowable stress516-60 Hydro Test 24,000
CA = Corrosion Allowance 0.0625

For Second Course 516-60 Plate 0.5000

td = 2.6(D)(H -1)(G)/Sd= 0.165

td =td / tt = 2.6(D)(H-1)/(St)
td = Miniumum shell thickness, in inches 0.209

D = Normal tank diameter , in feet 50.00

H = depth of tank , in feet 28
G = design Specific gravity of liquid 1
Sd = allowable StrStre
ess fo
for De
Design co
condition 21,30
,300
E = joint efficiency 0.85%
St = allowable stress 516-60 Hydro Test 24,000
CA = Corrosion Allowance 0.0625

For Third Course 516-60 Plate 0.3750

FileName: 230781857.xls.ms_office
Page 2 of 8 WorkSheet: Steel Design
 Art Montemayor API 650 Storage Tank March 12, 2002
Rev: 0

API 650 Design Calculations

Shell Design :

td = 2.6(D)(H -1)(G)/Sd= 0.196

td =td / tt = 2.6(D)(H-1)/(St) =
td = Miniumum shell thickness = 0.2365
0.2365 inches
inches

D = Normal tank diameter , in feet 94.5

H = depth of tank , in feet 18
G = design Specific gravity of liquid 1
Sd = allowable StrStre
ess fo
for De
Design co
condition 21,30
,300
E = joint efficiency 0.85%
St = allowable
allowable stress 516-60 Hydro Test 24,000
CA = Corrosion Allowance 0.0625

For Fourth Course 516-60 Plate 0.2500

td = 2.6(D)(H -1)(G)/Sd= 0.081

td =td / tt = 2.6(D)(H-1)/(St)
td = Miniumum shell thickness, in inches 0.1342

D = Normal tank diameter , in feet 94.5

H = depth of tank , in feet 8
G = design Specific gravity of liquid 1
Sd = allowable StrStre
ess fo
for De
Design co
condition 21,30
,300
E = joint efficiency 0.85%
St = allowable
allowable stress 516-60 Hydro Test 24,000
CA = Corrosion Allowance 0.0625

For Fifth Course 516-60 Plate 0.2500

Annular Bottom Plate Thickness 0.3750

D = Diameter in Feet 50.00

H = Height in Feet 32.00
V = Volume in Cubic Feet

2
Tank Shell
Shell surface = p*D*H = 5,027 Ft  of Shell surface area

Tank Roof surface = p*D2/4 = 2

1,963 Ft  of Roof Area (estimated)

Tank Floor surface = p*D2/4 = 2

1,963 Ft  of Bottom Floor area

FileName: 230781857.xls.ms_office
Page 3 of 8 WorkSheet: Steel Design
 Art Montemayor API 650 Storage Tank March 12, 2002
Rev: 0
FOUNDATION DESIGN:

Per API 650 (Appendix E)

Tank is unanchored, use equations pertaining to unanchored tanks,

for seismic loading.

DATA GIVEN:

Seismic Zone; 3
Zone Coefficient Z= 0.3
Importance Factor I = 1.0
Diameter of Tank D= 94.5
Height of Liquid Content (Design) H= 44.5
Shell Height Hs = 48
Design Specific Gravity G= 0.79
Thickness of Bottom PL Under Shell tb = 0.3750
Yeild Strength of Bottom PL Fby = 36,0
36,000
00 PSI
PSI
W eight of Shell Ws = 221
221 Kips
Kips
W eight of Roof + Live Load = 107.4 + 210.4 Wy = 317.
317.8
8 Kips
Kips
2
Weight of Product PI()/4(94.5)  (44.5)(.79)(62.4) Wt = 15,3
15,386
86 Kips
Kips

CALCULATIONS:

Seismic Coefficients:

Xs = 19.6
19.685
85 Ft
C1 = 0.60
D/H = 2.12

Per Fig. E-2

W 1 / W t = 0.535 W 1 = 8,231

W 2 / W t = 0.45 W 2 = 6,924

Per Fig. E-3

X1 /H = 0.375 X1 = 16.7

X2 /H = 0.59 X2 = 26.3

Per Fig. E-4

K = 0.6

Lateral Force Coefficients: E-3.3

0.5  0.5
T =K (D  ) =.6 *(94.5 )= 5.83 Seconds

2 2
If Greater Than 4.5 seconds 3.375 (s/T ) = 3.375*1.5/5.83  = 0.149 Seconds

FileName: 230781857.xls.ms_office
Page 4 of 8 WorkSheet: Foundation Design - 1
  Art Montemayor API 650 Storage Tank March 12, 2002
Rev: 0

FOUNDATION DESIGN:

Seismic Loads:

M = (Z)(I) {
(Z)(I) { (C1)(Ws)(Xs)+(C1)(Wr)(Ht)+(C1)(W)(X)+(C2)(W 2)(X2)}

(0.3)*(1.0)[ 0.6(221)(19.685)+ 0.6(317.8)(48.0)+ 0.6(8232)(16.7)+ 0.149(6924)(26.3)]

0.3 2610 9155 82485 27133 3641
36415
5 Ft-Ki
Ft-Kips
ps

V = (Z)(I) {(C1)(Ws)+(C1)(Wr)(Ht)+(C1)
{(C1)(Ws)+(C1)(Wr)(Ht)+(C1)(W)(X)+(C2)(W2)(X2)}
(W)(X)+(C2)(W2)(X2)}

(0.3)*(1.0)[ 0.6(221)+ 0.6(317.8)+ 0.6(8232)+ 0.149(6924)]

0.3 132.6 190.68 4939.2 1031.676 1888
1888 kips
kips

Reistance to Overturning:( E.4.1) API 650

W L = 7.9t b  Fby G H (G18)*(G16)*(G14)/(G13) ) 3,333 # / ft

1265580 1125
Constant = 7.9

3,333 # / ft Not to exceed 1.25*GHD 4153 # / ft

USE 4153 # / ft
Shell Compression: Per E-5

M= 36415 ft
ft-kips

Wt + W L = 583.8 / (PI()*94.5) + 4.153 6 Kips

2
M / D  (Wt + W L) (G76)/(G
(G76)/(G13)
13) (6.12)
(6.12)
36415 54653 0.666 > 0.785

b = 1.815+1.273*36415/94.5^2 b = 7.0

Max. Longitudinal Compressive Force 7.0

UnAnchored Longitudinal Compressive Stress

7000 / 6 1167
Allowable Longitudinal Compressive Stress
2 2 6 6
GHD /t 1.255 * 10  = Fa=10 (t) / D = 5.29 Kips
Anchorage Not Required

FileName: 230781857.xls.ms_office
Page 5 of 8 WorkSheet: Foundation Design - 1
 Art Montemayor API 650 Storage Tank March 12, 2002
FOUNDATION DESIGN: Rev: 0

Max
Max. Over
verturning Mome
Momen
nt Due To Seism
ismic Loads. 36,415 Kips
Compression or Tension Due To Moment: 5.19 kpf 
Seismic Base Shear: 0.27 kips

RINGWALL DESIGN:
Use Following Weight Values for Materials

3
Wt. of Steel 490lb/ft
3
Wt. Of Compacted Soil 110 lb/ft
3
Wt. Of Concrete Wall 150 lb/ft
3
Wt. Of Product in Tank 50 lb/ft

Horizontal Pressure on Ring Wall:

F=Kah(g*p*H+1/2 soh)+270
0.3*6.0[(50*44.5+0.5*110*6.0)]+270 4,869 kips

Hoop Tension:

1/2FD= 1/2(4869)(94.5) 230 kips

 As= 231/24.0 10 in.

USE - 6 # 9 Bars Ea. Face

USE - # 4 Bars at 12" on Center 

Minimum RingWall Thickness:

T = 2W / g *p*h - 2h ( gc - gso) W = 1100

(2)(1100)/50(44.5)-2(6.0)(150-110) 1.26
Use 16"
16" Thick Concrete Wall

12"
Top of Ground Elevation
16"
48"

12"

FileName: 230781857.xls.ms_office
Page 6 of 8 WorkSheet: Foundation Design - 2
 Art Montemayor API 650 Storage Tank March 12, 2002
Rev: 0

Concrete Tensile Stress:

f ct = c(Es)(As)+T / Ac + n (As)

6
.0003(29*10 )(10)+231000/(16*72)+(9*10)
318000 1242 256 psi
.15(3000) 450 psi
OK
Soil Bearing:

Try 3'- 6" Footing

Weight. of Wall = 1.33*5.0*.150 1.0 kips

Weight of Footing = 3.5*1.0*.150 0.525 kips
Weight of Fill = 2.17*4.0*.110 0.95 kips
2.48 kips

Case 1

Load from Shell + Roof + Live Load = 1.1 kips

Weight of Wall +Footing + Fill = 2.48 kips

Bearing Pressure = 3.58/3.50 1.0 kips

Case 2

Dead + Live Load + Earthquake Load =

P = 3.58 + 5.19 = 8.77 kips

H= 0.270 kips
Moment at Base of Footing = .270(6.0) 1.62 kips

Bearing Pressure Under Footing =

8.77/3.5*1 2.51 kips
2.51+.79 3.30 kips
Allowable Pressure = 3.0*1.33 3.99
OK

USE -4 # 9 Bars in Footing

USE - # 4 Bars at 12" Horizontal

FileName: 230781857.xls.ms_office
Page 7 of 8 WorkSheet: Foundation Design - 2
 Art Montemayor API 650 Storage Tank March 12, 2002
DETAILED FOUNDATION DESIGN: Rev: 0

47" - 3"

Center Line of Tank

Slope 1" per ft.

12"  .
  q 10" Pad of Sand 10"
   E
  e
  c
  a
   F Well-Compacted Gravel
   h
  c
95% Compacted
  a 50 / 100 % Passing # 4 Sieve
   E
  s
  r
  a
   "    B # 4 Bars 12" O/C Each Face
   0
  -
   '    9
   4    #
   6
95 % Compacted Subgrade or fill Material

1'-4" Wall

   "
   2
   1

(4) # 9 Bars Eq. Spaced

3' - 6"

NOTES:
1. Oiled sand to be mixture of sand and liquid asphalt (mc70):
2. Use 10 gallons of asphalt per cubic yard of sand:
3. Top of concrete to be smooth and level with 1/8" +/- in any 30 feet of circumferential length:
4. Maximum Deiation to be less than 1/4" overall:

FileName: 230781857.xls.ms_office
Page 8 of 8 WorkSheet: Foundation Design - 3