RV4PX310R-V2

10-port sector antenna, 2x 694–960 and 8x 1695–2690 MHz, 65°

HPBW, 5x RET with manual override. Bands cascaded SRET.
l Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual
override on all arrays

l All Internal RET actuators are connected in “Cascaded SRET

SRET”” configuration

Electrical Specifications
Frequency Band, MHz 694–798 790–894 890–960 1695–1880 1850–1990 1920–2200 2300–2690
Gain, dBi 16.0 16.6 16.9 16.8 16.9 17.2 18.0
Beamwidth, Horizontal, degrees 69 68 66 63 62 63 61
Beamwidth, Vertical, degrees 9.9 8.7 8.1 8.3 7.7 7.1 6.0
Beam Tilt, degrees 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10 0– 10
USLS (First Lobe), dB 18 18 18 18 18 18 18
Null Fill, dB -22 -22 -22 -22 -22 -22 -22
Front
Front--to
to--Back Ratio at 180°, dB 31 34 33 32 39 37 38
Isolation, Cross Polarization, dB 28 28 28 30 30 30 30
Isolation, Inter
Inter--band, dB 30 30 30 30 30 30 30
VSWR | Return Loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C,
200 200 200 175 175 175 175
maximum, watts
Polarization   ±45° ±45° ±45° ±45° ±45° ±45° ±45°
Impedance   50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm 50 ohm

Electrical Specifications, BASTA*

Frequency Band, MHz 694–798 790–894 890–960 1695–1880 1850–1990 1920–2200 2300–2690
Gain by all Beam Tilts, average, dBi 15.8 16.4 16.8 16.3 16.6 16.9 17.6
Gain by all Beam Tilts Tolerance,
±0.4 ±0.3 ±0.2 ±0.5 ±0.4 ±0.4 ±0.5
dB
0 ° | 15.9 0 ° | 16.4 0 ° | 16.7 0 ° | 16.3 0 ° | 16.6 0 ° | 16.9 0 ° | 17.6
Gain by Beam Tilt, average, dBi 5 ° | 15.8 5 ° | 16.4 5 ° | 16.7 5 ° | 16.3 5 ° | 16.6 5 ° | 17.0 5 ° | 17.6
10 ° | 15.8 10 ° | 16.4 10 ° | 16.8 10 ° | 16.4 10 ° | 16.7 10 ° | 16.9 10 ° | 17.4
Beamwidth, Horizontal Tolerance,
±1.3 ±0.7 ±1.4 ±2.3 ±1.8 ±2.7 ±5.2
degrees
Beamwidth, Vertical Tolerance,
±0.7 ±0.5 ±0.3 ±0.5 ±0.3 ±0.5 ±0.4
degrees
USLS, beampeak to 20° above
18 18 18 18 18 18 18
beampeak, dB
Front
Front--to
to--Back Total Power at 180°
26 27 27 26 29 27 29
± 30°, dB
CPR at Boresight, dB 16 18 17 17 21 19 18
CPR at Sector, dB 12 13 16 13 12 12 10

* CommScope
CommScope® ® supports NGMN recommendations on Base Station Antenna Standards (BASTA). To learn more about the benefits of BASTA, download the
whitepaper Time to Raise the Bar on BSAs.

Array Layout

page 1 of 5
August 20, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 17, 2019
RV4PX310R-V2

 
 

General Specifications
Operating Frequency Band 1695 – 2690 MHz   |   694 – 960 MHz
Antenna Type Sector
Band Multiband
Performance Note Outdoor usage   |   Wind loading figures are validated by wind tunnel measurements
described in white paper WP-112534-EN
Total Input Power, maximum 1000 W @ 50 °C
 

Mechanical Specifications
RF Connector Quantity, total 10
RF Connector Quantity, low band 2
RF Connector Quantity, high band 8
RF Connector Interface 7-16 DIN Female
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material Low loss circuit board
Radome Material Fiberglass, UV resistant
Reflector Material Aluminum
RF Connector Location Bottom
Wind Loading, frontal 445.0 N @ 150 km/h
100.0 lbf @ 150 km/h
Wind Loading, lateral 379.0 N @ 150 km/h
85.2 lbf @ 150 km/h
Wind Loading, maximum 942.0 N @ 150 km/h
211.8 lbf @ 150 km/h

page 2 of 5
August 20, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 17, 2019
RV4PX310R-V2

Effective Projected Area (EPA), frontal 0.42 m²   |   4.52 ft²

Effective Projected Area (EPA), lateral 0.36 m²   |   3.88 ft²
Wind Speed, maximum 241 km/h   |   150 mph
 

Dimensions
Length 2533.0 mm   |   99.7 in
Width 350.0 mm   |   13.8 in
Depth 208.0 mm   |   8.2 in
Net Weight, without mounting kit 39.0 kg   |   86.0 lb
 

Remote Electrical Tilt (RET) Information

Input Voltage 10–30 Vdc
Internal RET High band (4)   |   Low band (1)
Power Consumption, idle state, maximum 2W
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
RET Interface 8-pin DIN Female   |   8-pin DIN Male
RET Interface, quantity 1 female   |   1 male
 

Packed Dimensions
Length 2834.0 mm   |   111.6 in
Width 456.0 mm   |   18.0 in
Depth 357.0 mm   |   14.1 in
Shipping Weight 56.0 kg   |   123.5 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

Included Products
T -029
029--GL
GL--E — Adjustable Tilt Pipe Mounting Kit for 2.0"
2.0"--4.5" (60
(60--115mm) OD round members for panel antennas. Includes 2 clamp sets.

page 3 of 5
August 20, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 17, 2019
RV4PX310R-V2

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

page 4 of 5
August 20, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: June 17, 2019
T-029-GL-E

Adjustable Tilt Pipe Mounting Kit for 2.0"-4.5" (60-115mm) OD round

members for panel antennas. Includes 2 clamp sets.

General Specifications
Application Outdoor
Includes Brackets   |   Hardware
Package Quantity 1
 

Mechanical Specifications
Color Silver
Material Type Galvanized steel
Mechanical Tilt 0°–8°
 

Dimensions
Antenna-to-Pipe Distance 85.0 mm   |   3.3 in
Bracket-to-Bracket Distance 1400.0 mm   |   55.1 in
Compatible Diameter, maximum 115.0 mm   |   4.5 in
Compatible Diameter, minimum 60.0 mm   |   2.4 in
Compatible Length, maximum 2850.0 mm   |   112.2 in
Compatible Length, minimum 1500.0 mm   |   59.1 in
Net Weight 6.0 kg   |   13.2 lb

Regulatory Compliance/Certifications
Agency Classification
RoHS 2011/65/EU Compliant by Exemption
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
China RoHS SJ/T 11364-2014 Above Maximum Concentration Value (MCV)
CE Compliant with the relevant CE product directives

page 5 of 5
August 20, 2019

©2019 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope.All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: May 28, 2019