Dr.Arkan A.

Hussein Power Electronics Fourth Class

Single Phase Uncontrolled

Rectifier

١
Dr.Arkan A.Hussein Power Electronics Fourth Class

Operation and Analysis of single phase uncontrolled rectifiers

Instructional Objectives
On completion the student will be able to
• Classify the rectifiers based on their number of phases and the type of devices used.
• Define and calculate the characteristic parameters of the voltage and current waveforms.
• Analyze the operation of single phase uncontrolled half wave and full wave rectifiers
supplying resistive, inductive, capacitive and back emf type loads.
• Calculate the characteristic parameters of the input/output voltage/current waveforms
associated with single phase uncontrolled rectifiers.

٢
Dr.Arkan A.Hussein Power Electronics Fourth Class

9.1 Introduction
One of the first and most widely used application of power electronic devices have been in
rectification. Rectification refers to the process of converting an ac voltage or current source to
dc voltage and current. Rectifiers specially refer to power electronic converters where the
electrical power flows from the ac side to the dc side. In many situations the same converter
circuit may carry electrical power from the dc side to the ac side where upon they are referred to
as inverters. In this lesson and subsequent ones the working principle and analysis of several
commonly used rectifier circuits supplying different types of loads (resistive, inductive,
capacitive, back emf type) will be presented. Points of interest in the analysis will be.

• Waveforms and characteristic values (average, RMS etc) of the rectified voltage and

•
current.

•
Influence of the load type on the rectified voltage and current.

•
Harmonic content in the output.

•
Voltage and current ratings of the power electronic devices used in the rectifier circuit.
Reaction of the rectifier circuit upon the ac network, reactive power requirement, power

•
factor, harmonics etc.
Rectifier control aspects (for controlled rectifiers only)

In the analysis, following simplifying assumptions will be made.

•
•
The internal impedance of the ac source is zero.
Power electronic devices used in the rectifier are ideal switches.

The first assumption will be relaxed in a latter module. However, unless specified otherwise, the
second assumption will remain in force.
Rectifiers are used in a large variety of configurations and a method of classifying them
into certain categories (based on common characteristics) will certainly help one to gain
significant insight into their operation. Unfortunately, no consensus exists among experts
regarding the criteria to be used for such classification. For the purpose of this lesson (and
subsequent lessons) the classification shown in Fig 9.1 will be followed.

٣
Dr.Arkan A.Hussein Power Electronics Fourth Class

This Lesson will be concerned with single phase uncontrolled rectifiers.

9.2 Terminologies
Certain terms will be frequently used in this lesson and subsequent lessons while characterizing
different types of rectifiers. Such commonly used terms are defined in this section.

Let “f” be the instantaneous value of any voltage or current associated with a rectifier

Peak value of f ( f̂ ) : As the name suggests f̂ = f

circuit, then the following terms, characterizing the properties of “f”, can be defined.
max over all time.

Fav = ∫ f(t)dt ……………………………….(9.1)

Average (DC) value of f(Fav) : Assuming f to be periodic over the time period T
1 T
T 0

RMS (effective) value of f(FRMS) : For f , periodic over the time period T,

T ∫0
1 T 2
FRMS = f (t)dt …………………………..(9.2)

Form factor of f(fFF) : Form factor of ‘f ‘ is defined as

F
f FF = RMS …………………………………. …(9.3)
Fav

Ripple factor of f(fRF) : Ripple factor of f is defined as

2 2
FRMS - Fav 2
f RF = = f FF -1 …………………….(9.4)
Fav

٤
Dr.Arkan A.Hussein Power Electronics Fourth Class

Ripple factor can be used as a measure of the deviation of the output voltage and current of a

( )
rectifier from ideal dc.

Peak to peak ripple of f f̂ pp : By definition

f̂ pp = f max - f min Over period T……………… …(9.5)

Fundamental component of f(F1): It is the RMS value of the sinusoidal component in the

( )
Fourier series expression of f with frequency 1/T.

∴ F1 =
1 2 2
f A1 + f B1 ………………………....(9.6)

where f A1 = ∫ f ( t ) cos 2π t dt ……………………(9.7)

2
2 T

f B1 = ∫ f ( t ) sin 2π t dt …………………….(9.8)
T 0
2 T
T 0 T

Kth harmonic component of f(FK): It is the RMS value of the sinusoidal component in the

( )
Fourier series expression of f with frequency K/T.

∴ FK =
1 2 2
f AK + f BK …………………………(9.9)

where f AK = ∫ f(t) cos2πK t T dt ………………...(9.10)

2
2 T

f BK = ∫ f(t) sin2πK t T dt …………………(9.11)

T 0
2 T
T 0

Crest factor of f(Cf) : By definition

f̂
Cf = ……………………………………(9.12)
FRMS

Distortion factor of f(DFf) : By definition

F
DFf = 1 …………………………………..(9.13)
FRMS

Total Harmonic Distortion of f(THDf): The amount of distortion in the waveform of f is

quantified by means of the index Total Harmonic Distortion (THD). By definition

THD f = ∑ ⎜ ⎟ ………………………..(9.14)
⎛ Fk ⎞
α 2

K=0 ⎝ F1 ⎠
K ≠1

From which it can be shown that

2
1- DFf
THDf = ……………………………(9.15)
DFf

٥
Dr.Arkan A.Hussein Power Electronics Fourth Class

Displacement Factor of a Rectifier (DPF): If vi and ii are the per phase input voltage and input

DPF = cosφi …………………………………(9.16)

current of a rectifier respectively, then the Displacement Factor of a rectifier is defined as.

Where φi is the phase angle between the fundamental components of vi and ii.

Power factor of a rectifier (PF): As for any other equipment, the definition of the power factor
of a rectifier is
PF =
Actual power input to the Rectifier
….(9.17)
Apparent power input to the Rectifier
if the per phase input voltage and current of a rectifier are vi and ii respectively then
V I cosφi
PF = i1 i1 ………………………………(9.18)
ViRMS IiRMS

If the rectifier is supplied from an ideal sinusoidal voltage source then

Vi1 = ViRMS
I
so, PF = i1 cosφi = DFi1 × DPF ………………..(9.19)
IiRMS
In terms of THDii
DPF
PF = ……………………………...(9.20)
2
1+ THDii
Majority of the rectifiers use either diodes or thyristors (or combination of both) in their
circuits. While designing these components standard manufacturer’s specifications will be
referred to. However, certain terms are used in relation to the rectifier as a system. They are
defined next.

Pulse number of a rectifier (p): Refers to the number of output voltage/current pulses in a
single time period of the input ac supply voltage. Mathematically, pulse number of a rectifier is
given by
Time period of the input supply voltage
p= .
Time period of the minium order harmonic in the output voltage/current.
Classification of rectifiers can also be done in terms of their pulse numbers. Pulse number of a
rectifier is always an integral multiple of the number of input supply phases.

Commutation in a rectifier: Refers to the process of transfer of current from one device (diode
or thyristor) to the other in a rectifier. The device from which the current is transferred is called
the “out going device” and the device to which the current is transferred is called the “incoming
device”. The incoming device turns on at the beginning of commutation while the out going
device turns off at the end of commutation.

Commutation failure: Refers to the situation where the out going device fails to turn off at the
end of commutation and continues to conduct current.

Firing angle of a rectifier (α): Used in connection with a controlled rectifier using thyristors. It
refers to the time interval from the instant a thyristor is forward biased to the instant when a gate
pulse is actually applied to it. This time interval is expressed in radians by multiplying it with

٦
Dr.Arkan A.Hussein Power Electronics Fourth Class

the input supply frequency in rad/sec. It should be noted that different thyristors in a rectifier
circuit may have different firing angles. However, in the steady state operation, they are usually
the same.

Extinction angle of a rectifier (γ): Also used in connection with a controlled rectifier. It refers
to the time interval from the instant when the current through an outgoing thyristor becomes zero
(and a negative voltage applied across it) to the instant when a positive voltage is reapplied. It is
expressed in radians by multiplying the time interval with the input supply frequency (ω) in
rad/sec. The extinction time ( /ω) should be larger than the turn off time of the thyristor to avoid
commutation failure.

Overlap angle of a rectifier (μ): The commutation process in a practical rectifier is not
instantaneous. During the period of commutation, both the incoming and the outgoing devices
conduct current simultaneously. This period, expressed in radians, is called the overlap angle
“μ” of a rectifier. It is easily verified that α + μ + = π radian.

Exercise 9.1

Fill in the blank(s) with the appropriate word(s).

i) In a rectifier, electrical power flows from the _________ side to the ________ side.
ii) Uncontrolled rectifiers employ _________ where as controlled rectifiers employ
________ in their circuits.
iii) For any waveform “Form factor” is always _______ than or equal to unity.
iv) The minimum frequency of the harmonic content in the Fourier series expression of
the output voltage of a rectifier is equal to its _________.
v) “THD” is the specification used to describe the quality of ___________ waveforms
where as “Ripple factor” serves the same purpose for _________ for waveforms.
vi) Input “power factor” of a rectifier is given by the product of the _________ factor
and the ________ factor.
vii) The sum of “firing angle”, “Extinction angle” and “overlap angle” of a controlled
rectifier is always equal to _________.

Answers: (i) ac, dc; (ii) diodes, thyristors; (iii) greater; (iv) pulse number; (v) ac, dc; (vi)
displacement, distortion; (vii) π

9.3 Single phase uncontrolled half wave rectifier

This is the simplest and probably the most widely used rectifier circuit albeit at relatively small
power levels. The output voltage and current of this rectifier are strongly influenced by the type
of the load. In this section, operation of this rectifier with resistive, inductive and capacitive
loads will be discussed.

٧
Dr.Arkan A.Hussein Power Electronics Fourth Class

Fig 9.2 shows the circuit diagram and the waveforms of a single phase uncontrolled half
wave rectifier. If the switch S is closed at at t = 0, the diode D becomes forward biased in the
the interval 0 < ωt ≤ π. If the diode is assumed to be ideal then
For 0 < ωt ≤ π
v0 = vi = √2 Vi sin ωt
vD = vi – v0 = 0 ………………………(9.21)
Since the load is resistive
2V0
i0 = v0 R = sinωt …………………..(9.22)
R
ii = i0
For ωt > π, vi becomes negative and D becomes reverse biased. So in the interval π < ωt ≤ 2π
ii = i0 = 0
v0 = i0R = 0………………………………...(9.23)
vD = vi – v0 = vi = √2 Vi sinωt
From these relationships

∫ ∫
1 2π 1 π 2Vi
V0AV = v 0 dωt = 2Vi sinωtdωt = ……….(9.24)
π

∫
2π 0 2π 0
1 π 2 2 V
VDRMS = 2Vi sin ωtdωt = i ……………………...(9.25)
2π 0 2

٨
Dr.Arkan A.Hussein Power Electronics Fourth Class

It is evident from the waveforms of v0 and i0 in Fig 9.2 (b) that they contain significant amount
of harmonics in addition to the dc component. Ripple factor of v0 is given by
2 2
VDRM - VDAV 1 2
v0RF = = π - 4 ………………………… (9.26)
VDAV 2
With a resistive load ripple factor of i0 will also be same.

Because of such high ripple content in the output voltage and current this rectifier is
seldom used with a pure resistive load.

The ripple factor of output current can be reduced to same extent by connecting an
inductor in series with the load resistance as shown in Fig 9.3 (a). As in the previous case, the
diode D is forward biased when the switch S is turned on. at ωt = 0. However, due to the load
inductance i0 increases more slowly. Eventually at ωt = π, v0 becomes zero again. However, i0
is still positive at this point. Therefore, D continues to conduct beyond ωt = π while the negative
supply voltage is supported by the inductor till its current becomes zero at ωt = . Beyond this
point, D becomes reverse biased. Both v0 and i0 remains zero till the beginning of the next cycle
where upon the same process repeats.

From the preceding discussion

For 0 ≤ ωt ≤
vD = 0
v0 = vi
i0 = ii…………………………………………(9.27)
for ≤ ωt ≤ 2π

٩
Dr.Arkan A.Hussein Power Electronics Fourth Class

v0 = 0
i0 = ii = 0

∫ v0 dωt = ∫ 2Vsinωtdωt
vD = vi – v0 = vi

( )
1 2π 1
V0AV = i ………………… (9.28)
2π 0 2π 0
2Vi 1- cos
or V0AV = ………………………………………... (9.29)
π 2

∫
( - 12 sin2 ) = V2
1
2Vi sin ωtdωt
2 2
V0RMS =
2π 0
2
Vi i 2 - sin2
= ……………………..(9.30)
2π 2π

Form factor of the voltage waveform is

V 2 - sin2
vOFF = 0RMS = π 2
………………………………….(9.31)
V0AV 2π(1- cos )

The ripple factor.

2 π(2 - sin2 )
v0RF = vOFF -1 = 2
- 1 ………………………………(9.32)
2(1- cos )

All these quantities are functions of which can be found as follows.

For 0 ≤ ωt ≤
dio
vi = 2Vsinωt
i =L + Ri0 …………………………………….(9.33)
dt
i0 (ωt = 0) = i0 (ωt = ) = 0

The solution is given by

ωt
-
2Vi
sin(ωt - φ) ……………………………………(9.34)
tanφ
i 0 = I0 e +
Z

ωL
where tanφ =
R
R + ω L ……………………………………………..(9.35)
2 2 2
and Z =

2Vi ⎡ ⎤
Putting the initial conditions of (9.33)

⎢⎣sinφe + sin ( ωt - φ ) ⎥⎦ ………………………………(9.36)

ωt
-
tanφ
i0 =

2Vi ⎡ ⎤
Z

⎢sinφe
⎣ + sin ( - φ ) ⎦⎥ = 0
-
tanφ
i 0 (ωt = ) =
Z

= sin ( φ - ) ………………………………………….(9.37)
-
tanφ
or sinφe
as a function of φ can be obtained by solving equation 9.37.

١٠
Dr.Arkan A.Hussein Power Electronics Fourth Class

It can be shown that increases with φ. From Equation (9.29), V0AV decreases with
increasing while V0RMS increases with . Therefore, with increasing φ (and hence increasing
L) the form factor and the ripple factor of v0 worsens. However, the ripple factor of i0 decreases
with increasing L. Therefore, in certain applications, where a smooth dc current is of prime
importance (e.g. the field supply of a dc motor) this configuration of the rectifier is preferred.

The problem of poor form factor (ripple factor) of the output voltage can be solved to
some extent by connecting a capacitor across the load resistance of Fig 9.2 (a). This single phase
half wave rectifier supplying a capacitive load is shown in Fig 9.5 (a). Corresponding
waveforms are shown in Fig 9.5 (b).

If the capacitor was initially discharged the diode “D” is forward biased when the switch
S is turned on at ωt = 0. The output voltage follows the input voltage. The diode D carries both
the capacitor charging current and the load current. At ωt = the sum of these two currents
becomes zero and tends to grow in the negative direction. At this point the diode becomes

١١
Dr.Arkan A.Hussein Power Electronics Fourth Class

reverse biased and disconnects the load (along with the capacitor) from the supply. The
capacitor then discharges with the load current. Diode D does not become forward biased till the
input supply voltage becomes equal to the capacitor voltage in the next cycle at ωt = (2π + φ).
The same process repeats thereafter.

For 2π + φ ≤ ωt ≤ 2π +
From the preceding discussion

v0 = vi = 2V1sinωt ……………………………………..(9.38)
dv v
ii = i c + i0 = c 0 + 0
dt R

or ii =
2Vi
[ ωRCcosωt + sinωt ]

2Vi ( )
R
1

1+ ω R C cos(ωt - θ) ……………………..(9.39)
2 2 2 2
=
R
1
where θ = tan
-1

ωRC

١٢
Dr.Arkan A.Hussein Power Electronics Fourth Class

At ωt = + 2π, ii = 0 so – θ = π/2 or = θ + π/2

π -1 1
or = + tan ……………………………………….(9.40)
2 ωRC

Again for ≤ ωt ≤ 2π + φ

ii = 0, C 0 + 0 = 0, v 0 ( ωt = ) = 2Vi cosθ .
dv v
dt R
∴ v 0 = 2Vi cosθ e
-(ωt- ) tanθ
…………………………………..(9.41)

at ωt = 2π + φ, v0 = 2Vsinφ
i

2Vi sinϕ = 2Vi cosθ e

π
-(2π+φ- -θ) tanθ
2

3π
-( +φ-θ) tanθ
2
or sinφ = cosθ e
⎡ -( -θ) tanθ ⎤ -φ tanθ
or sinφ = ⎣cosθ e 2 ⎦e
3π

……………………………...(9.42)

From which φ can be solved. Peak to peak ripple in v0 is

v̂ 0pp = 2Vi (1- sinϕ) ………………………………………….(9.43)

As c → α, θ → 0 and and φ → π/2 and v̂0pp → 0

Therefore, a very large capacitor helps to improve the ripple factor of the output voltage of this
rectifier. However, as indicated by Equation (9.39) the peak current through the diode increases
proportionately. It is also interesting to observe that unlike the previous cases the peak reverse
voltage appearing across D is given by.
v D max = 2Vi + v 0M ≈ 2 2Vi ………………………………(9.44)
This is sometimes referred to as the peak inverse voltage rating (PIV) of the diode.

Exercise 9.2

1. Fill in the blank(s) with the appropriate word(s).

i) The ripple factor of the output voltage and current waveforms of a single phase
uncontrolled half wave rectifier is ____________ than unity.
ii) With an inductive load, the ripple factor of the output __________ of the half wave
rectifier improves but that of the output __________ becomes poorer.
iii) In both single phase half wave and full wave rectifiers the form factor of the output
voltage approaches _________ with capacitive loads provided the capacitance is
________ enough.
iv) The PIV rating of the rectifier diode used in a single phase half wave rectifier
supplying a capacitive load is approximately ________ the __________ input supply
voltage.
v) The % THD of the input current of the rectifiers supplying capacitive loads is
__________.

Answers: (i) greater; (ii) current, voltage; (iii) unity, large; (iv) double, peak; (v) high.

١٣
Dr.Arkan A.Hussein Power Electronics Fourth Class

2. An unregulated dc. power supply of average value 12 V and peak to peak ripple of 20% is to
be designed using a single phase half wave rectifier. Find out the required input voltage, the
output capacitance and the diode RMS current and PIV ratings. The equivalent load
resistance is 50 ohms.

v̂opp = 2Vi (1- sinϕ ) = 0.2×12 = 2.4 V.

Answer: From equation 9.43.

∴ Vomax = 2Vi = 12 + 2.4 2 = 13.2V ∴ Vi = 9.33V

∴ sin ϕ = 0.818 or ϕ = 54.9 = 0.96 rad.
o

Then from equation 9.42

-(3 π 2 + ϕ - θ) tanθ
0.818 = cosθ e
(5.67 - θ) tanθ
or 0.818 e = cosθ
From which θ ≈ 2.035
c

∴ tan θ = = 0.03553, R = 50Ω, ∴ C = 1790 μF

1
ωRC

ii dωt = i 2 (1+ ω R C )
PIV of the diode = 2 2Vi = 26.4V .

∫ 2π ∫54.9o
1 V 1 92.035 2
cos (ωt - θ)dωt
2 2 2 2

2π ϕ
RMS. Diode current =

1 ⎡ -ϕ 1
R
⎤
⎢ + sin2( - θ) - sin2(ϕ - θ) ⎥ = 0.8564 Amps.
2π ⎣ 2 ⎦
1
= 7.432
4 4

9.4 Single phase uncontrolled full wave rectifier

Single phase uncontrolled half wave rectifiers suffer from poor output voltage and/or
input current ripple factor. In addition, the input current contains a dc component which may
cause problem (e.g. Transformer saturation etc) in the power supply system. The output dc
voltage is also relatively less. Some of these problems can be addressed using a full wave
rectifier. They use more number of diodes but provide higher average and rms output voltage.
There are two types of full wave uncontrolled rectifiers commonly in use. If a split
power supply is available (e.g. output from a split secondary transformer) only two diode will be
required to produce a full wave rectifier. These are called split secondary rectifiers and are
commonly used as the input stage of a linear dc voltage regulator. However, if no split supply is
available the bridge configuration of the full wave rectifier is used. This is the more commonly
used full wave uncontrolled rectifier configuration. Both these configurations are analyzed next.

١٤
Dr.Arkan A.Hussein Power Electronics Fourth Class

9.4.1 Split supply single phase uncontrolled full wave rectifier.

١٥
Dr.Arkan A.Hussein Power Electronics Fourth Class

Fig 9.6 shows the circuit diagram and waveforms of a single phase split supply,
uncontrolled full wave rectifier supplying an R – L load. The split power supply can be thought
of to have been obtained from the secondary of a center tapped ideal transformer (i.e. no internal
impedance).
When the switch is closed at the positive going zero crossing of v1 the diode D1 is
forward biased and the load is connected to v1. The currents i0 and ii1 start rising through D1.
When v1 reaches its negative going zero crossing both i0 and ii1 are positive which keeps D1 in
conduction. Therefore, the voltage across D2 is vCB = v2 - v1 . Beyond the negative going zero
crossing of vi, D2 becomes forward biased and the current i0 commutates to D2 from D1. The
load voltage v0 becomes equal to v2 and D1 starts blocking the voltage vAB = v1 - v2 . The current
i0 however continues to increase through D2 till it reaches the steady state level after several
cycles. Steady state waveforms of the variables are shown in Fig 9.6 (b) from ωt = 0 onwards. It
should be noted that the current i0, once started, always remains positive. This mode of operation
of the rectifier is called the “Continuous conduction mode” of operation. This should be
compared with the i0 waveform of Fig 9.3 (b) for the half wave rectifier where i0 remains zero
for some duration of the input supply waveform. This mode is called the “ discontinuous
conduction mode” of operation.

For 0 ≤ ωt < π
From the above discussion

v0 = v1

for π ≤ ωt < 2π
i0 = ii1……………………………………....(9.45)

v0 = v2
i0 = ii2……………………………………........(9.46)

Since v0 is periodic over an interval π

V0AV = ∫ v 0 dωt = ∫
1 π 2Vi π 2 2Vi
sinωtdωt = ……………..(9.47)
π π π

π ∫0 i
0 0

1 π 2 2
V0RMS = 2V sin ωt dωt = Vi ………………………........(9.48)

∴ v 0FF = 0RMS =
V π
……………………………………….(9.49)
V0AV 2 2
π -8
2
2
v 0RF = v -1 =
0FF ……………………………………..(9.50)
2 2
Both the form factor and the ripple factor shows considerable improvement over their half wave
counter parts.

١٦
Dr.Arkan A.Hussein Power Electronics Fourth Class

١٧
Dr.Arkan A.Hussein Power Electronics Fourth Class

The single phase full wave rectifier still does not offer a smooth dc voltage. With
resistive load, considerable ripple current will flow into the load. This problem can be solved by
connecting a capacitor across the load resistance just as in the case of a half wave rectifier.
If the capacitor was initially discharged, the diode D1 is forward biased when the switch S
is turned on at ωt = 0. The diode D2 remains reverse biased. The output voltage follows the
input voltage. D1 carries both the capacitor charging current and the load current. At ωt = the
sum of these two currents becomes zero and tends to grow in the negative direction. At this
point the diode D1 becomes reverse biased and disconnects the load along with the capacitor
from the supply. The capacitor then discharges through the load until at ωt = π + φ, v2 becomes
greater than v0 and forward biases D2. D1 now remains reverse biased. D2 conducts up to ωt = π
+ . The same process repeats thereafter.

For π + φ ≤ ωt ≤ π +
From the discussion above

v0 = v2 = - 2Vsinωt i

dv v
ii2 = i c + i 0 = C 0 + 0 ………………………………………………(9.51)
dt R
or ii2 = -
2Vi
[ ωRCcosωt + sinωt ]

2Vi ( )
R

1+ ω R C cos ( π + θ - ωt ) where θ = tan

1
2 2 2 2 -1 1
= ….(9.52)
R ωRC
π π π 1
at ωt = π + , ii1 = 0 so - θ = or = θ + or = + tan
-1
…………(9.53)
2 2 2 ωRC

Again for ≤ ωt ≤ π + φ

ii1 = 0 ∴ C 0 + 0 = 0 v0 ( ωt = )=
dv v
2Vsin
i = 2Vi cosθ ……….(9.54)
dt R
-( ωt- ) tanθ
∴ v 0 = 2Vi cosθ e …………………………………………….(9.55)

( π2 +θ-π-φ)tanθ
at ωt = π + φ, v0 = 2sinφ

( π2 +φ-θ )tanθ
2Vsinφ
i = 2Vi cosθ e
-

-( -θ ) tanθ ⎤ -φtanθ
or sinφ = cosθ e
⎡
or sinφ = ⎣cosθ e 2 ⎦e
π

………………………………………(9.56)

From which φ can be solved. Peak to peak ripple in v0 is

v̂ 0pp = 2Vi (1- sinφ) ………………………………………………….(9.57)

It can be shown that for the same R and C, v̂0pp given by Equation (9.57) is smaller than that
given by Equation (9.43) for the half wave rectifier. The diode PIV ratings remain equal to
2 2Vi however.

١٨
Dr.Arkan A.Hussein Power Electronics Fourth Class

Exercise 9.3

1. Fill in the blank(s) with the appropriate word(s).

i) The output voltage form factor of a single phase full wave rectifier is ___________.
ii) The output voltage of a single phase full wave rectifier supplying an inductive load is
___________ of the load parameters.
iii) The peak to peak output voltage ripple of a single phase split supply full wave
rectifier supplying a capacitive load is ___________ compared to an equivalent half
wave rectifier.

Answers: (i) π ; (ii) independent ; (iii) smaller.

2 2

2. An unregulated dc power supply is built around a single phase split supply full wave rectifier
using the same input voltage and output capacitor found in the problem 2 of Exercise 9.2.
The load resistance is 50 Ω. Find out the average output voltage, the peak to peak ripple in
the output voltage and the RMS current ratings of the diodes.

Answer: From the given data C = 1790 μF, R = 50 Ω, ∴ θ = 2.035°

From equation 9.56
Sin θ = cos θ e-(π/2 + φ – θ) tan θ
-0.03553(1.5353+ϕ ) -0.03553ϕ
Or sin θ = 0.99937 e = 0.946316 e
From which φ = 65.33°

∴ vˆ opp = 2Vi (1- sinϕ ) = 1.20 volts.

Vi = 9.33 volts.

v̂ opp
V0AV = V0Max - = 2Vi - 0.6V = 13.2 - 0.6V = 12.6V .
∴ % ripple = 9.5%
2

∫ ii dωt = i 2 (1+ ω R C ) ∫
1 π 2+θ 2 V 1
cos (ωt - θ)dωt
2 2 2 2

2π ϕ 2π ϕ
RMS diode current =

1 ⎡ -ϕ 1
R
⎤
⎢ - sin2(ϕ - θ) ⎥ = 0.533 Amps.
2π ⎣ 2 4 ⎦
= 7.432

١٩
Dr.Arkan A.Hussein Power Electronics Fourth Class

9.4.2 Single phase uncontrolled full bridge rectifier

٢٠
Dr.Arkan A.Hussein Power Electronics Fourth Class

The split supply full wave single phase rectifier offers as good performance as possible from a
single phase rectifier in terms of the output voltage form factor and ripple factor. They have a
few disadvantages however. These are

•
•
They require a split power supply which is not always available.
Each half of the split power supply carries current for only one half cycle. Hence they are
underutilized.

٢١
Dr.Arkan A.Hussein Power Electronics Fourth Class

• The ratio of the required diode PIV to the average out put voltage is rather high.

These problems can be mitigated by using a single phase full bridge rectifier as shown in Fig 9.8
(a). This is one of the most popular rectifier configuration and are used widely for applications
requiring dc. power output from a few hundred watts to several kilo watts. Fig 9.8 (a) shows the
rectifier supplying an R-L-E type load which may represent a dc. motor or a storage battery.
These rectifiers are also very widely used with capacitive loads particularly as the front end of a
variable frequency voltage source inverter. However, in this section analysis of this rectifier
supplying an R-L-E load will be presented. Its operation with a capacitive load is very similar to
that of a split supply rectifier and is left as an exercise.

When the switch S is turned on at the positive going zero crossing of vi no current flows in the
circuit till vi crosses E at point A. Beyond this point, D1 & D2 are forward biased by vi and
current starts increasing through them till the point B. After point B, vi falls below E and io starts
decreasing. Now depending on the values of R, L & E one of the following situations may arise.

•
•
io may become zero before the negative going zero crossing of vi at point C.

•
io may continue to flow beyond C and become zero before the point D.
io may still be non zero at point D.

It should be noted that if io >0 either D1D2 or D3D4 must conduct. Fig 9.4 (b) shows the
waveforms for the third situation.

If io >0 at point C the negative going input voltage reverse biases D1 & D2. Current io
commutates to D3 and D4 as shown in the associated “conduction Diagram” in Fig 9.8 (b). It
shows pictorially the conduction interval of different devices. The current io continues to
decrease up to the point D beyond which it again increases. It should be noted that in this mode
of conduction io always remain greater than zero. Consequently, this is called the continuous
conduction mode of operation of the rectifier. In the other two situations the mode of operation
will be discontinuous.

right of the point ωt = 0 in Fig 9.4 (b).

The steady state waveforms of the rectifier under continuous conduction mode is shown to the

0 < ωt ≤ π
From this figure and preceding discussion
For
vo = vi = 2Vi sin ωt (9.58)

π < ωt ≤ 2π
ii = io
for
v o = - vi = - 2Vi sin ωt (9.59)
ii = - io

∴ VoAV = ∫
1 π 2 2
2Vi 2sin ωt d ωt = Vi (9.60)
π o π

π ∫o i
1 π
VoRMS = 2V 2 sin 2 ωt d ωt = Vi (9.61)

٢٢
Dr.Arkan A.Hussein Power Electronics Fourth Class

∴ v OFF =
VoRMS π
=
VoAV 2 2
2 π2 - 8
v oRF = v OFF -1 = (9.62)
2 2

Finding out the characterizing quantities for ii will be difficult owing to its complicated
waveform. Considerable, simplification is achieved (without significant loss of accuracy) by
replacing the actual io waveform by its average value IoAV = VoAV / R.

Fig 9.9 shows the approximate input current wave form and its fundamental component.

Displacement angle φi = 0
From Fig 9.9

∴ Input displacement factor (DPF) = cos ϕi = 1 (9.63)

I 2 2
Distortion factor (DFil) = il = (9.64)
IoAV π
2 2
Power Factor (PF) = DPF × DFil = (9.65)
π
1 - DFii 2 π2 - 8
% TH Dii = 100 × = 100 × (9.66)
DFii 2 2 2

٢٣
Dr.Arkan A.Hussein Power Electronics Fourth Class

The exact analytical expression for io (and hence ii) can be obtained as follows.

for 0 < ωt ≤ π
Ldi o
vi = 2Vi sin ωt = Ri o + +E (9.67)
dt
io ωt=0 = io ωt=π (steady state periodic boundary cond.)

The general solution can be written as

2Vi ⎡ sinθ ⎤
⎢ sin ( ωt - ϕ ) -
cosϕ ⎥⎦
i o = Io e tanϕ +
- ωt

Z ⎣
(9.68)

where tanϕ =
ωL E
; Z = R 2 + ω2 L2 ; sin θ =
R 2Vi

From the boundary condition

2Vi ⎡ sinθ ⎤ 2Vi ⎡ sinθ ⎤
ϕ sin ϕ -
Z ⎢⎣ cosϕ ⎥⎦ Z ⎢⎣ cosϕ ⎥⎦
- tanπϕ
Io - sin + = I o e +

2Vi 2 sinϕ
Io = (9.69)
1 - e tanϕ
-π
Z
2 Vi ⎡ 2 sinϕ sinθ ⎤
∴ io = ⎢⎣1 - e tanϕ ( ϕ )
cosϕ ⎥⎦
ϕ
ωt
- tan
- π e + sin ωt - - (9.70)
Z

From which the condition for continuous conduction can be obtained.

for continuous conduction io ≥ 0 for all 0 < ω t ≤ π

hence io Min ≥ 0 or io ωt=θ ≥ 0
∴ Condition for continuous conduction is
2 sinϕ - θ tanϕ
= sin (ϕ - θ ) +
sin θ
-π tanϕ
cos ϕ
e (9.71)
1- e

If the parameters of the load (i.e, R, L &E) are such that the left hand side of equation 9.71 is less
than the right hand side conduction of the rectifier becomes discontinuous i.e, the load current
becomes zero for a part of the input cycle. Discontinuous conduction mode of operation of this
rectifier is discussed next.

٢٤
Dr.Arkan A.Hussein Power Electronics Fourth Class

٢٥
Dr.Arkan A.Hussein Power Electronics Fourth Class

operation. In this mode of operation D1 D2 are not forward biased till vi exceed E at ωt = θ.
Fig. 9.10(b) shows the waveforms of different variables under discontinuous conduction mode of

Consequently, no current flows into the load till this time. After ωt = θ, the load is connected to
the input source through D1 D2 and io starts building up. Beyond ωt = π - θ, io starts decreasing
and becomes zero at ωt = β < π. D1 D2 are reverse biased at this point. D3 D4 are forward biased
at ωt = π + θ when io starts increasing again. Thus none of the diodes conduct during the interval
β < ω + ≤ π + θ and io remains zero during this period.

Form the preceding discussion

٢٦
Dr.Arkan A.Hussein Power Electronics Fourth Class

for θ < ωt ≤ < π

vo = vi = 2Vi sin ωt (9.72)
ii = i o

for π < π + θ < ω + ≤ π + < 2π

v o = - vi = - 2Vi sin ωt
ii = - io (9.73)
vo = E
ii = i o = 0 other wise (9.74)

∫ ∫ 2Vi sin ωt + ∫ E d ωt ⎤
1 ⎡
π ⎣ θ ⎦
1 π+θ π+θ
VoAV = vo d ωt =
π θ

[ cos θ - cos + ( π + θ - ) sin θ ]

2Vi
OR VoAV = (9.75)
π

β can be found in the following manner

for θ < ωt ≤
Ldi o
v = 2 sin ωt = R i o + +E (9.76)
dt
i o ωt =θ = io ωt= = 0

The general solution is

2Vi ⎡ sin θ ⎤
sin ( ωt - φ ) -
ωt-θ

⎢ cos ϕ ⎥⎦
ϕ

Z ⎣
- tan
i o = Io e + (9.77)

where tanϕ = ωL , Z = R 2 + ω2 L2 , sinθ = E

R 2Vi
From the initial condition io ωt=θ = 0
⎡sin (ϕ - θ ) + sinθ ⎤
⎢⎣ cosϕ ⎥⎦

( )
2Vi
Io = (9.78)
Z
⎡sin ϕ - θ e- tanωt-θϕ - sinθ 1- e -ωt-θ + sin ( ωt - ϕ ) ⎤⎥
∴ io = ⎢⎣ ( )
cosϕ
2Vi tanϕ

⎦
(9.79)
Z
Putting i o ωt = = 0 in Equation 9.79.
sinθ ⎡
sin ( - ϕ ) = 1 - e tanϕ ⎤ - sin (ϕ - θ ) e
cosϕ ⎣⎢ ⎦⎥
θ- θ-
tanϕ
(9.80)

Form which β can be solved.

Exercise 9.4

1. Fill in the blank(s) with the appropriate word(s).

i) The average output voltage of a full wave bridge rectifier and a split supply full wave
rectifier are __________ provided the input voltages are ___________.

٢٧
Dr.Arkan A.Hussein Power Electronics Fourth Class

ii) For the same input voltage the bridge rectifier uses ___________ the number of
diodes used in a split supply rectifier with _________ the PIV rating.
iii) For continuous conduction, the load impedance of a bridge rectifier should be
__________.
iv) In the ___________ conduction mode the output voltage of a bridge rectifier is
__________ of load parameters.

Answers: (i) equal, equal; (ii) double, half; (iii) inductive; (iv) continuous, independent.

2. A battery is to be charged using a full bridge single phase uncontrolled rectifier. On full
discharge the battery voltage is 10.2 V. and on full charge it is 12.7 volts. The battery
internal resistance is 0.1Ω. Find out the input voltage to the rectifier so that the battery
charging current under full charge condition is 10% of the charging current under fully
discharged condition. Assume continuous conduction under all charging condition and find
out the inductance to be connected in series with the battery for this condition.

Answer: Let the rectifier input voltage be Vi and the charging current under fully discharged
condition be I.
Then assuming continuous conduction
2 2Vi 2 2
- 0.1I = 10.2 and V - 0.01I = 12.7
π π i
∴ 0.09I = 2.5 V ∴ I = 27.78 Amps and Vi = 14.415 volts.
If conduction is continuous at full charge condition it will be continuous for all other
charging conditions.

2sinϕ -θ tanϕ
For continuous conduction
= sin(ϕ - θ) +
cosϕ
sinθ
-π tanϕ
e
1- e
E
From given data sinθ = = 0.623, θ = 38.535°
2Vi
From which φ = 86.5°
∴ tan ϕ = ωL = 16.35 or ωL = 1.635 ohms
∴ L = 5.2 mH.
R

References
[1] P.C. Sen, “Power Electronics”, Tata McGraw –Hill Publishing Company Limited. 1995
[2] Muhammad H. Rashid, “Power Electronics, circuits, Devices and applications” Prentice –
Hall of India Private Limited, Second Edition, 1994

٢٨
Dr.Arkan A.Hussein Power Electronics Fourth Class

Module Summary
• A rectifier is a power electronic converter which converts ac voltage or current sources to
dc voltage and current.
• In a rectifier, electrical power flows from the ac input to the dc output.
• In many rectifier circuits, power can also flow from the dc side to the ac side, where
upon, the rectifier is said to be operating in the “inverter mode”.
• Rectifiers can be classified based on the type of device they use, the converter circuit
topology, number of phases and the control mechanism.
• All rectifiers produce unwanted harmonies both at the out put and the input. Performance
of a rectifier is judged by the relative magnitudes of these harmonies with respect to the
desired output.
• For a given input voltage and load, the output voltage (current) of an uncontrolled
rectifier can not be varied. However, the output voltage may vary considerably with load.
• Single phase uncontrolled half wave rectifier with resistive or inductive load have low
average output voltage, high from factor and poor ripple factor of the output voltage
waveform.
• Single phase uncontrolled full wave rectifier have higher average output voltage and
improved ripple factor compared to a half wave rectifier with resistive and inductive load.
• With highly inductive load the output voltage waveform of a full wave rectifier may be
independent of the load parameters.
• With a capacitive load the output voltage form factor approaches unity with increasing
capacitance value for both the half wave and the full wave rectifiers. However, THD of
the input current also increases.
• A full wave bridge rectifier generates higher average dc voltage compared to a split
supply full wave rectifier. However it also uses more number of diodes.

٢٩