Client : Date : DEC-05

Project : Calc'd by : MS
Estimate no : Checked by : SM
Contract no :
Sheet no :C04-C1/ 1

CONNECTION NO - C04-C1

LOADS:
305X305X118 UC
Compression Fc := 900 ⋅ kN

Major axis moment Mz := 300 ⋅ kN ⋅ m

305X305X118 UC

A 6 A
75 550 75 BASE PLATE
30 THK NON-CEMENTITIOUS 700X650X60 THK
NON-SHRINK GROUT
300

120 WASHER PLATE

(TYP)
(TYP) 120X120X20THK
150
(TYP)
200

650
150

GROUT HOLES
50 DIA (TYP)
SECTION A-A

NOTES:-
All bolts are M24 grade 8.8 holding down bolts in 30mm dia holes.
All main steels & fittings are S355.

Variation no: Rev date Description

 Client : Date : DEC-05
Project : Calc'd by : MS
Estimate no : Checked by : SM
Contract no :
Sheet no :C04-C1/ 2

SECTIONAL PROPERTIES

Column : 305X305X118 UC
2
Dc := 314.5mm wc := 307.4mm Tc := 18.7mm tc := 12mm rc := 15.2mm dc := 246.7mm Ac = 15000 mm

MATERIAL PROPERTIES

N
Design strength of S355 material up to & including 16 mm thk. py355 := 355 ⋅
2
mm

N
Design strength of S355 material beyond 16 mm thk and upto and including 40 mm thk. py345 := 345 ⋅
2
mm

N
Design strength of S355 material beyond 40 mm thk and upto and including 63 mm thk. py335 := 335 ⋅
2
mm

N
Design strength of weld pw := 250 ⋅
2
mm

Check for bolted splice connection

Dia of bolt d := 24mm

Total no of bolts per side nc := 4

Total no of bolts n := 8

Enhanced tension capacity of Pte = 198 kN

Holding Down bolt

N
Cube strength of concrete (C25) fcu := 25
2
mm

N
Design bearing strength of concrete fcud := 0.4 ⋅ fcu fcud = 10
2
mm
Check for base plate connection

Width of base plate provided wbp := 700mm

Depth of base plate provided Dbp := 650mm

tbp := 60mm
Thickness of base plate provided

Variation no: Rev date Description

 Client : Date : DEC-05
Project : Calc'd by : MS
Estimate no : Checked by : SM
Contract no :
Sheet no :C04-C1/ 3

Finding the dimension 'X',

Distance between C/L of tensile bolt from h := 625mm

outer edge of compressive stress block
Fc
0.6 ⋅ fcu ⋅ Dbp kN
Let k := k = 4.9
2 mm

0.6 fcu
T
l := 0.6 ⋅ f cu ⋅ Dbp ⋅ h l = 6093.8 kN
wbp C
X
q := Fc ⋅ h − Fc ⋅ + Mz q = 547.5 kN ⋅ m
2 h=625mm
wp=700mm
2
−l + l − 4 ⋅ ( k ⋅ q)
X1 := X1 = 97.44 mm
−2 ⋅ k

2
−l − l − 4 ⋅ ( k ⋅ q)
X2 := X2 = 1152.56 mm
−2 ⋅ k
Adopt reasonable length of
X := 97.44mm Fc
compresiive stress block L1

Check for base plate thickness

0.6 fcu
T
Compression side bending
C
Assume column flange weld s w := 6mm
wbp − Dc
Effective length of projected portion e := − 0.8 ⋅ s w e = 188 mm
in compression side 2
2
e
Moment per mm width applied to mC := 0.6 ⋅ fcu ⋅ mC = 264.9 kN
plate from stress block 2

4 ⋅ mC
Thickness of base plate reqd tbpreqd1 := tbpreqd1 = 56.2 mm
on compression side py335

Tension side bending

Tension per side (
T := 0.6 ⋅ fcu ⋅ Dbp ⋅ X − Fc ) T = 50 kN
wbp − Dc
Effective length of projected portion e1 := − 0.8 ⋅ s w e = 188 mm
in tension side 2

Moment induced on base plate

mT := T ⋅ e1 mT = 9.4 kN ⋅ m
due to tension

Thickness of base plate reqd 4 ⋅ mT

tbpreqd2 := tbpreqd2 = 13.1 mm
on tension side py335 ⋅ Dbp

Thickness of base plate reqd (

tbpreqd := max tbpreqd1 , tbpreqd2 ) tbpreqd = 56.2 mm

Adopt 60mm thk base plate.

Variation no: Rev date Description

 Client : Date : DEC-05
Project : Calc'd by : MS
Estimate no : Checked by : SM
Contract no :
Sheet no :C04-C1/ 4

Check for holding down bolts

T
Tension acting each bolt Ft := Ft = 12.5 kN
nc

Ft (12.51 kN) < Pte (198 kN): Therefore O.K.

Check for conical pull out of tension bolts

2 (From steel designer's manual,
Surface area of conical pull-out Acp := 525800mm
P.No.796, Table 27.2)
Ft N
Surface stress due to conical pull-out vcp := vcp = 0.02
Acp 2
mm
N (From BS8110-1:1997,
vc := 0.34
Design shear stress of concrete 2 P.No.32,table 3.8)
mm
vcp (0.02 N/mm^2) < vc (0.34 N/mm^2): Therefore O.K.

Check for punching shear of concrete section

Anchorage length of
L := 300mm
holding down bolts provided
Washer plate width bap := 120mm

Washer plate length lap := 120mm

Washer plate thickness tap := 20mm

Washer plate perimeters overlap.

Perimeter around the anchor plate ( )
Lp := 2 ⋅ 120mm + bap + 2 ⋅ ( 3 ⋅ L) + 2 ⋅ ( 3 ⋅ L) Lp = 4080 mm

T N
Average shear stress over fv := fv = 0.04
effective depth Lp ⋅ L 2
mm

fv (0.04 N/mm^2) < vc (0.34 N/mm^2): Therefore O.K.

Check for washer plate bearing on concrete

5

2
.8

Awp := bap ⋅ lap Awp = 14400 mm

72

Area of washer plate

60

B
120

ø of bolt=24

Diameter of tube Dtb := 50mm

ø
of

120
tu
be
=5
0

2
π ⋅ Dtb
Area of tube Atb := 2
4 Atb = 1963.5 mm

Bearing area of concrete Abcw := Awp − Atb 2

Abcw = 12436.5 mm
@ washer plate location

Variation no: Rev date Description

 Client : Date : DEC-05
Project : Calc'd by : MS
Estimate no : Checked by : SM
Contract no :
Sheet no :C04-C1/ 5

Bearing stress on concrete Ft

fcbw := N
@ washer plate location Abcw fcbw = 1.01
2
mm

fcbw (1.01 N/mm^2) < fcud (10 N/mm^2): Therefore O.K.

Check for washer plate bending

5
.8
2
⎛ bap ⎞

72
d
( 60mm) + ⎜
2

60
lbw := − lbw = 72.85 mm

B
Max length of bending

120
ø of bolt=24
⎝ 2 ⎠ 2

ø
of
120

tu
⎛ Dtb − d ⎞

be
=5
llw := lbw − ⎜

0
Length of loading llw = 59.9 mm
⎝ 2 ⎠
⎡ llw⎤ kN ⋅ mm
Moment acting @ B per mm
⎣
(
Mwp := fcbw ⋅ llw ⋅ ⎢ lbw − llw + )
2⎦
⎥ Mwp = 2.6
mm
2
tap kN ⋅ mm
Moment capacity of Mcwp := ⋅ py345 Mcwp = 23
washer plate per mm 6 mm

Mwp (2.58 kNmm/mm) < Mcwp(23 kNmm/mm): Therefore O.K.

Weld between column flange and base plate

Length available for weld Lweld := 2 ⋅ wc − tc − 2 ⋅ rc Lweld = 572.4 mm

Mz wc ⋅ Tc
Net force acting in the column flange Fw := − Fc ⋅ Fw = 669.3 kN
Dc − Tc Ac

Fcf := wc ⋅ Tc ⋅ py345 Fcf = 1983.2 kN

Capacity of column flange

(
min Fw , Fcf ) kN
Force acting on the FT := FT = 1.2
flange weld per mm Lweld mm

FT
Size of weld required s w := s w = 5.35 mm
1.25 ⋅ 0.7 ⋅ pw

Adopt 6mm CFW allround.

Variation no: Rev date Description