Scribd
Upload
50 views4 pages

Triangular Wave Generator Using Opamp: What Are Triangular Waves?

This document describes a triangular wave generator circuit using op-amps. It generates a triangular wave by integrating a square wave. The circuit uses one op-amp as a square wave generator and a second op-amp as an integrator. The square wave generator uses a capacitor and resistors to produce an oscillating output. This square wave is fed into the integrator op-amp, which uses the square wave as an input and a capacitor and resistor to integrate it and produce a triangular wave output.

Uploaded by

Arun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
50 views4 pages

Triangular Wave Generator Using Opamp: What Are Triangular Waves?

This document describes a triangular wave generator circuit using op-amps. It generates a triangular wave by integrating a square wave. The circuit uses one op-amp as a square wave generator and a second op-amp as an integrator. The square wave generator uses a capacitor and resistors to produce an oscillating output. This square wave is fed into the integrator op-amp, which uses the square wave as an input and a capacitor and resistor to integrate it and produce a triangular wave output.

Uploaded by

Arun
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Triangular wave generator using opamp

This is an interesting project for newbies. This article is about creating a


triangular wave generator using opamp IC. There are many methods for
generating triangular waves but here we focus on the method using opamps.
This circuit is based on the fact that a square wave on integration gives a
triangular wave.

What are Triangular waves?


Triangular waves are a periodic, non-sinusoidal waveform with a triangular
shape. People often get confused between the triangle and sawtooth waves. The
most important feature of a triangular wave is that it has equal rise and fall times
while a sawtooth wavehas un-equal rise and fall times.

To generate triangular waves we need an input wave. In this project, we are


using square waves for input. Like triangular waves, square waves have equal
rise and fall times so they are more convenient to be converted to a triangular
waveform.

The main parts of this project are 1. A square wave generator 2. An integrator
which converts square waves to triangular waves.

The circuit uses an opamp based square wave generator for producing the
square wave and an opamp based integrator for integrating the square wave.
The circuit diagram is shown in the figure below.
Circuit diagram

The square wave generator section and the integrator section of the circuit are
explained in detail below.

Square wave generator

The square wave generator is based on a uA741 opamp (IC1).  Resistor R1


and capacitor C1 determines the frequency of the square wave. Resistor R2 and
R3 forms a voltage divider setup which feedbacks a fixed fraction of the output to
the non-inverting input of the IC.
Initially, when power is not applied the voltage across the capacitor C1 is 0.
When the power supply is switched ON, the C1 starts charging through the
resistor R1 and the output of the opamp will be high (+Vcc). A fraction of this high
voltage is fed back to the non- inverting pin by the resistor network R2, R3. When
the voltage across the charging capacitor is increased to a point the voltage at
the inverting pin is higher than the non-inverting pin, the output of the opamp
swings to negative saturation (-Vcc). The capacitor quickly discharges through
R1 and starts charging in the negative direction again through R1. Now a fraction
of the negative high output (-Vcc) is fed back to the non-inverting pin by the
feedback network R2, R3. When the voltage across the capacitor has become so
negative that the voltage at the inverting pin is less than the voltage at the non-
inverting pin, the output of the opamp swings back to the positive saturation. Now
the capacitor discharges trough R1 and starts charging in positive direction. This
cycle is repeated over time and the result is a square wave swinging between
+Vcc and -Vcc at the output of the opamp.

If the values of R2 and R3 are made equal, then the frequency of the square
wave can be expressed using the following equation:
                                                                            F=1 / (2.1976 R1C1)

Integrator

Next part of the triangular wave generator is the opamp integrator. Instead of
using a simple passive RC integrator, an active integrator based on opamp is
used here. The opamp IC used in this stage is also uA741 (IC2). Resistor R5 in
conjunction with R4 sets the gain of the integrator and resistor R5 in conjunction
with C2 sets the bandwidth. The square wave signal is applied to the inverting
input of the opamp through the input resistor R4. The opamp integrator part of
the circuit is shown in the figure below.

Let’s assume the positive side of the square wave is first applied to the
integrator. By virtue capacitor C2 offers very low resistance to this sudden shoot
in the input and C2 behaves something like a short circuit. The feedback resistor
R5 connected in parallel to C2 can be put aside because R5 has almost zero
resistance at the moment. A serious amount of current flows through the input
resistor R4 and the capacitor C2 bypasses all these current. As a result the
inverting input terminal (tagged A) of the opamp behaves like a virtual ground
because all the current flowing into it is drained by the capacitor C2. The gain of
the entire circuit  (Xc2/R4) will be very low and the entire voltage gain of the
circuit will be close to the zero.

After this initial “kick”  the capacitor starts charging and it creates an opposition to
the input current flowing through the input resistor R4. The negative feedback
compels the opamp to produce a voltage at its out so that it maintains the virtual
ground at the inverting input. Since the capacitor is charging its impedance Xc
keeps increasing and the gain Xc2/R4 also keeps increasing. This results in a
ramp at the output of the opamp that increases in a rate proportional to the RC
time constant (T=R4C2) and this ramp increases in amplitude until the capacitor
is fully charged.
When the input to the integrator (square wave) falls to the negative peak the
capacitor quickly discharges through the input resistor R4 and starts charging in
the opposite polarity. Now the conditions are reversed and the output of the
opamp will be a ramp that is going to the negative side at a rate proportional to
the R4R2 time constant. This cycle is repeated and the result will be a triangular
waveform at the output of the opamp integrator.

Testing the triangular wave generator.


Testing videos, practical circuit diagram, and photographs will be added soon.

Applications:
The applications of triangular wave include sampling circuits, thyristor firing
circuits, frequency generator circuits, tone generator circuits etc.

You might also like