Scribd
Upload
709 views1 page

Mazatrol-EIA Tool Data Params

The document provides instructions for using Mazatrol tool data with an EIA/ISO program. There are three key areas that need configuration: 1) Setting four parameters to make the tool length, diameter, and offsets from the Mazatrol tool data valid for the EIA/ISO program. 2) Configuring the Mazatrol tool data. 3) Setting the work offset data. Following these steps will allow a program to run standalone or be called as a subprogram from a Mazatrol main program using the tooling definitions from the Mazatrol system.

Uploaded by

Eduardo Aleman Reyna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
709 views1 page

Mazatrol-EIA Tool Data Params

The document provides instructions for using Mazatrol tool data with an EIA/ISO program. There are three key areas that need configuration: 1) Setting four parameters to make the tool length, diameter, and offsets from the Mazatrol tool data valid for the EIA/ISO program. 2) Configuring the Mazatrol tool data. 3) Setting the work offset data. Following these steps will allow a program to run standalone or be called as a subprogram from a Mazatrol main program using the tooling definitions from the Mazatrol system.

Uploaded by

Eduardo Aleman Reyna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

l',lazak

M-32 ETA/ TSO PROGRAI"IIy{'ING SAJ"IPLE

TJS I NG MAZATROL TO()L DATA

rhe following is the recommended Frocedure for using Mazatrol tool


data t{ith,an ErA/ISO program. FoIlbwins this procedure uiII allow the
program to be used as a stand alone program, or to be call as a sub
program from a Mazatrol main program.

There are three areas of informaticn that need to be set for this to
slork correctly.

1. Parameter settings.
2. Tool data setting.
3- Work offset data setting.

PAR.AIVIETER. SETT I $IG

There are four parameters th'at must be set. There functions are as
follows

F93 bit #3 set to I


This makes the TOOL LENGTH from the }lazatrol tool data screen
valid for EIA/ISo progrems. This tool tength becomes effective on the
first move after tool change end does not reguire the use of G43 or an
H offset- (see the program sahple lines N3 through N7)

F94 bit *2 set to I


This stops the tool length from being canceled on a G28 or G30
co'mmand. (see the sample prograrn lines N54 & N56)
CAUTION... IF THIS PARAH.ETERIS NOT SET TO I, AND A G28 OR G3O IS
EXECI'TED TIIE I{AEHINE T{ILL TRY TO I,(OVE IrHE SPINDLE FACE TO THE CURRENT
I,OCATIO!{ OF TIIE TOOI, TIP.

F92 bit S7 set to I


T h i s m a k e s t h e A C T U A L D I A I ' { E T E Rf r o m t t r e H a z a t r o l tool data screen
valid for EIA/Iso prograrns. This diameter is used sith the G4I, G42
cutter comp. commands- The control understands that this is a diameter
value and will apply half of the diameter as the offset amourtt. The D
eommandis not required with the c41 or G{2. (see the sample program
IineE N23 and N39) .

F84 bit fl set to 1


This causes the tool Iength to be applied to the position display
counter. (fhis has no effeEt on program operation)

You might also like