Scribd
Upload
452 views4 pages

TS 500-2000 (R2018) Example 001 PDF

This document summarizes the shear and flexural reinforcement design of a simply supported rectangular concrete beam according to the Turkish TS 500-2000(R2018) concrete design code. The beam geometry, material properties, and loading are defined. ETABS is used to calculate the flexural and shear reinforcement, which is then compared to independent hand calculations. The results show an exact match between ETABS and the independent calculations.

Uploaded by

Henry Tugano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
452 views4 pages

TS 500-2000 (R2018) Example 001 PDF

This document summarizes the shear and flexural reinforcement design of a simply supported rectangular concrete beam according to the Turkish TS 500-2000(R2018) concrete design code. The beam geometry, material properties, and loading are defined. ETABS is used to calculate the flexural and shear reinforcement, which is then compared to independent hand calculations. The results show an exact match between ETABS and the independent calculations.

Uploaded by

Henry Tugano
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Software Verification

PROGRAM NAME: ETABS


REVISION NO.: 0

TS 500-2000(R2018) Example 001


Shear and Flexural Reinforcement Design of a Singly Reinforced Rectangle

EXAMPLE DESCRIPTION
The flexural and shear strength of a rectangular concrete beam is tested in this
example.

A simply supported beam is subjected to a uniform factored load of 36.67 kN/m.


This example is tested using the Turkish TS 500-2000(R2018) concrete design
code. The flexural and shear reinforcing computed is compared with independent
results.

GEOMETRY, PROPERTIES AND LOADING

A 230mm
CL

60 mm 550 mm

A
Section A-A
6m

Material Properties Section Properties Design Properties


E= 25.000x106 kN/m2 d = 543.75 mm fck = 30 MPa
ν= 0.2 fy = 420 MPa

Clear span, L = 6000 mm


Overall depth, h = 550 mm
Width of beam, b = 230 mm
Effective depth, d = 490 mm
Concrete strength, fck = 30 MPa
Yield strength of steel, fyk = 420 MPa
Concrete unit weight, wc = 0 kN/m3
Modulus of elasticity, Ec = 25x103 MPa
Modulus of elasticity, Es = 2x105 MPa
Poisson’s ratio, v = 0.2

-1
Software Verification
PROGRAM NAME: ETABS
REVISION NO.: 0

TECHNICAL FEATURES TESTED


 Calculation of flexural and shear reinforcement
 Application of minimum flexural and shear reinforcement

RESULTS COMPARISON

Percent
Output Parameter ETABS Independent Difference

Design Moment, Md (kN-m) 165.02 165.02 0.00%

Tension Reinf, As (mm2) 1022 1022 0.00%

Design Shear, Vd (kN) 110.0 110.0 0.00%

Shear Reinf, Asw/s (mm2/mm) 0.2415 0.2415 0.00%

COMPUTER FILE: TS 500-2000(R2018) EX001

CONCLUSION
The computed results show an exact match with the independent results.

TS 500-2000(R2018) Example 001 - 2


Software Verification
PROGRAM NAME: ETABS
REVISION NO.: 0

HAND CALCULATION

Flexural Design
The following quantities are computed for the load combination:
f ck 30
f cd    20
 mc 1.5
f yk 420
f yd    365
 ms 1.15
 cu Es
cb  d = 304.6 mm
 cu Es  f yd
amax = 0.85k1cb = 212.3 mm
where, k1  0.85  0.006  f ck  25   0.82 , 0.70  k1  0.85
0.8 f ctd
As ,min  bd  315.5 mm 2
f yd

0.35 f cu 0.35 30
Where f ctd    1.278
 mc 1.5

COMB1
d = 36.67 kN/m

d L2
Md 
8
∙
= 36.67 62/8 = 165.02 kN-m

The depth of the compression block is given by:

2 Md
a  d  d2  = 95.42 mm
0.85 fcd b
Compression steel not required since a < amax.

The area of tensile steel reinforcement is given by:

Md 165E6
As = =
 a 365 •  490  95.41/ 2 
f yd  d  
 2

As = 1022 mm2

TS 500-2000(R2018) Example 001 - 3


Software Verification
PROGRAM NAME: ETABS
REVISION NO.: 0

Shear Design
The shear demand is computed as:
L
Vd  =110.0 kN at face of support for this example
2
The shear force is limited to a maximum of,
Vmax  0.85 f ck Aw  524 kN

The nominal shear strength provided by concrete is computed as:


 N 
Vcr  0.65 fctd bd 1  d
  =93.6 kN, where Nd  0
 Ag 
Vc  0.8Vcr  74.9 kN
The shear reinforcement is computed as follows:
If Vd  Vcr

 Asw  f ctd mm2


   0.3 b  0.2415 (min. controls) (TS 8.1.5, Eqn 8.6)
 s min f ywd mm

If Vcr  Vd  Vmax

Asw Vd  Vc  mm2


  0.1962 (TS 8.1.4, Eqn 8.5)
s f ywd d mm

TS 500-2000(R2018) Example 001 - 4

You might also like