Product information

Klüberoil GEM 1 N
High-performance gear oils / multi-purpose oils based on mineral oil
and KlüberComp Lube Technology

Benefits for your application

– The oils meet the requirements according to DIN 51517-3, CLP. Corresponding gears can be switched to Klüberoil
GEM 1 N oils without prior consultation with the gear manufacturer provided the general application notes are
observed.
– KlüberComp Lube Technology involves the selection of high-quality raw materials and individual consultation and
services by Klüber, ensuring high-performance lubrication of different gearbox components.
– Klüberoil GEM 1 N oils offer a high scuffing load resistance of ISO VG 150 API GL-4 or higher. Gears are sufficiently
protected against scuffing even at extremely high peak loads, vibrations or oscillations.
– The oils' high micropitting resistance according to FVA 54 GFT ≥ 10 offers sufficient protection to gears that are
subject to high loads and would normally be susceptible to this type of damage.
– The good wear protection of both gears and rolling bearings ensures that the service life calculated for the lubricated
components is achieved, leading to lower maintenance and repair costs.
– Much longer service life than mineral-oil-based standard gear oils due to the excellent ageing and oxidation
resistance of the selected raw materials; thus service intervals can be extended and maintenance costs reduced.
– Low foaming tendency as determined in the Flender foam test enable leakage and problem-free gear operation.
– Freudenberg seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klüberoil GEM 1 N oils.
Leakage and contamination are prevented.
– Approved by Siemens (Flender), Siemens Geared Motors, FLSmidth MAAG Gears, SEW Eurodrive, Getriebebau Nord,
Lenze Gears, Stöber Antriebstechnik, ZAE Antriebssysteme, Moventas, Bonfiglioli etc.

Description Application notes

Klüberoil GEM 1 N oils are gear and multi-purpose oils based on Klüberoil GEM 1 N oils can be applied by means of immersion,
selected mineral oils with a high resistance to oxidation. immersion circulation or injection.
They have a high resistance to scuffing and micropitting as laid The use of drip-feed oilers, brushes, oil cans or suitable
down in FVA 54. automatic lubricating systems is also possible.
The good antiwear characteristics of the Klüberoil GEM 1 N oils When using automatic lubricating systems, please note the
were also proven for rolling bearings in the standard FAG FE8 manufacturer's instructions regarding the maximum permissible
test rig for gear oils. viscosity. Low-viscosity lubricants are also used for oil mist
lubrication. It should be noted that elastomers from one or several
manufacturers can behave differently; therefore tests should be
Application performed.
The Klüberoil GEM 1 N oils were specially developed for the
lubrication of spur, bevel, hypoid and planetary gears that are Viscosity selection
subject to high loads. Such gears are frequently used in the wind,
steel, mining and sugar industries. When determining the oil viscosity for gears, the manufacturer's
instructions take priority.Only for applications where
The Klüberoil GEM 1 N oils are also used for the lubrication of
manufacturer's instructions are not available, the suitable
standard worm gears as defined in DIN 3996.
viscosity can be determined as laid down in DIN 51 509.To
They are also used for the lubrication of plain and rolling bearings, determine the correct oil viscosity for bearings, please observe
all kinds of toothed couplings, chains, guideways, joints, spindles the bearing manufacturer's instructions.
and pumps.

Klüberoil GEM 1 N, Prod. 030050, 030051, 030054, 030057, 030058, 030062, 030063, 030064, 030049, en
Edition 20.06.2014 [replaces edition 17.02.2014]
Product information

Klüberoil GEM 1 N
High-performance gear oils / multi-purpose oils based on mineral oil
and KlüberComp Lube Technology

Material safety data sheets

Material safety data sheets can be requested via our website
www.klueber.com. You may also obtain them through your
contact person at Klüber Lubrication.

Viscosity-temperature diagram

120 000 120 000

100 000 100 000

40 000 40 000

20 000 20 000

10 000 10 000

5 000 5 000

3 000 3 000
2 000 2 000

1 000 1 000

400 400
300 300

200 200

90 90
70 70

50 50
40 40
Klüberoil GEM 1-1000 N
30 30
Klüberoil GEM 1-680 N
Klüberoil GEM 1-460 N
20 20
Klüberoil GEM 1-320 N
15 15
Klüberoil GEM 1-220 N

10 10 Klüberoil GEM 1-150 N

8 8 Klüberoil GEM 1-100 N

7 7 Klüberoil GEM 1-68 N
6 6
Kinematic viscosity in mm²/s

5 5 Klüberoil GEM 1-46 N

4 4

3 3

2 2
-20 -10 0 10 20 30 40 50 60 70 80 90 100 110

Temperature in °C

Klüberoil GEM 1 N, Prod. 030050, 030051, 030054, 030057, 030058, 030062, 030063, 030064, 030049, en
Edition 20.06.2014 [replaces edition 17.02.2014]
Product information

Klüberoil GEM 1 N
High-performance gear oils / multi-purpose oils based on mineral oil
and KlüberComp Lube Technology

Pack sizes Klüberoil GEM 1-46 Klüberoil GEM 1-68 Klüberoil GEM
N N 1-100 N
Canister 20 l + + +
Drum 200 l + + +

Product data Klüberoil GEM 1-46 Klüberoil GEM 1-68 Klüberoil GEM
N N 1-100 N
Article number 030050 030051 030054
Marking acc. to DIN 51502 CLP 46 CLP 68 CLP 100
Classification acc. to ISO 12925-1 CKC 46 CKC 68 CKC 100
Lower service temperature -15 °C / 5 °F -15 °C / 5 °F -5 °C / 23 °F
Upper service temperature 100 °C / 212 °F 100 °C / 212 °F 100 °C / 212 °F
Density, based on DIN 51757) at 15 °C approx. 870 kg/m³ approx. 880 kg/m³ approx. 880 kg/m³
Kinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, 40 approx. 46 mm²/s approx. 68 mm²/s approx. 100 mm²/s
°C
Kinematic viscosity, DIN 51562 pt. 01/ASTM D-445/ASTM D 7042, approx. 7 mm²/s approx. 9 mm²/s approx. 11 mm²/s
100 °C
Viscosity index, DIN ISO 2909 >= 90 >= 90 >= 90
ISO viscosity grade, DIN ISO 3448 46 68 100
Flash point, DIN EN ISO 2592, Cleveland, open-cup apparatus >= 200 °C >= 200 °C >= 200 °C
Pour point, DIN ISO 3016 <= -20 °C <= -15 °C <= -15 °C
Foam test, ASTM-D 892, ISO 6247, sequence I/24 °C <= 100/10 ml <= 100/10 ml <= 100/10 ml
Foam test, ASTM-D 892, ISO 6247, sequence II/ 93.5 °C <= 100/10 ml <= 100/10 ml <= 100/10 ml
Foam test, ASTM D 892, ISO 6247, sequence III/24°C <= 100/10 ml <= 100/10 ml <= 100/10 ml
Ageing properties, ASTM D 2893, increase in viscosity <= 6 % <= 6 % <= 6 %
FZG scuffing test, DIN ISO 14635-1, A/8.3/90, scuffing load stage >= 14 >= 14 >= 14
FZG scuffing test, based on DIN ISO 14635-1, A/16.6/90, scuffing >= 12 >= 12 >= 12
load stage
API scuffing load capacity
FAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of <= 30 mg <= 30 mg <= 30 mg
rolling element
FAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of cage <= 200 mg <= 200 mg <= 200 mg
Anticorrosive properties on steel, DIN ISO 7120, method A, steel, 24 no rust no rust no rust
h/60 °C
Copper corrosion, DIN EN ISO 2160, 3 h/100 °C 1 - 100 corrosion 1 - 100 corrosion 1 - 100 corrosion
degree degree degree
Minimum shelf life from the date of manufacture - in a dry, frost-free 60 months 60 months 60 months
place and in the unopened original container, approx.

Klüberoil GEM 1 N, Prod. 030050, 030051, 030054, 030057, 030058, 030062, 030063, 030064, 030049, en
Edition 20.06.2014 [replaces edition 17.02.2014]
Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM
1-150 N 1-220 N 1-320 N 1-460 N 1-680 N 1-1000 N
+ + + + + +
+ + + + + +

Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM Klüberoil GEM
1-150 N 1-220 N 1-320 N 1-460 N 1-680 N 1-1000 N
030057 030058 030062 030063 030064 030049
CLP 150 CLP 220 CLP 320 CLP 460 CLP 680 CLP 1000
CKC 150 CKC 220 CKC 320 CKC 460 CKC 680 CKC 1000
-5 °C / 23 °F -5 °C / 23 °F -5 °C / 23 °F -5 °C / 23 °F 0 °C / 32 °F 0 °C / 32 °F
100 °C / 212 °F 100 °C / 212 °F 100 °C / 212 °F 100 °C / 212 °F 100 °C / 212 °F 100 °C / 212 °F
approx. 880 kg/m³ approx. 890 kg/m³ approx. 900 kg/m³ approx. 910 kg/m³ approx. 930 kg/m³ approx. 920 kg/m³
approx. 150 mm²/s approx. 220 mm²/s approx. 320 mm²/s approx. 460 mm²/s approx. 680 mm²/s approx. 1 000 mm²/s

approx. 15 mm²/s approx. 19 mm²/s approx. 25 mm²/s approx. 30 mm²/s approx. 37 mm²/s approx. 48 mm²/s

>= 90 >= 90 >= 90 >= 90 >= 85 >= 85

150 220 320 460 680 1 000
>= 200 °C >= 200 °C >= 200 °C >= 200 °C >= 200 °C >= 200 °C
<= -10 °C <= -10 °C <= -10 °C <= -10 °C <= -5 °C <= -3 °C
<= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml
<= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml
<= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml <= 100/10 ml
<= 6 % <= 6 % <= 6 % <= 6 % <= 6 % <= 6 %
>= 14 >= 14 >= 14 >= 14 >= 14 >= 14
>= 12 >= 12 >= 12 >= 12 >= 12 >= 12

API GL 4 API GL 4 API GL 4 API GL 4 API GL 4 API GL 4

<= 30 mg <= 30 mg <= 30 mg <= 30 mg <= 30 mg <= 20 mg

<= 200 mg <= 200 mg <= 200 mg <= 200 mg <= 200 mg <= 200 mg
no rust no rust no rust no rust no rust no rust

1 - 100 corrosion 1 - 100 corrosion 1 - 100 corrosion 1 - 100 corrosion 1 - 100 corrosion 1 - 100 corrosion
degree degree degree degree degree degree
60 months 60 months 60 months 60 months 60 months 60 months
 Product information

Klüberoil GEM 1 N
High-performance gear oils / multi-purpose oils based on mineral oil
and KlüberComp Lube Technology

Klüber Lubrication München SE & Co. KG /

Geisenhausenerstraße 7 / 81379 München / Germany /
Klüber Lubrication – your global specialist phone +49 89 7876-0 / fax +49 89 7876-333.
The data in this document is based on our general experience and knowledge
Innovative tribological solutions are our passion. Through at the time of publication and is intended to give information of possible
personal contact and consultation, we help our customers applications to a reader with technical experience. It constitutes neither an
assurance of product properties nor does it release the user from the
to be successful worldwide, in all industries and markets. obligation of performing preliminary field tests with the product selected for a
With our ambitious technical concepts and experienced, specific application. All data are guide values which depend on the lubricant's
competent staff we have been fulfilling increasingly composition, the intended use and the application method. The technical
values of lubricants change depending on the mechanical, dynamical, chemical
demanding requirements by manufacturing efficient high- and thermal loads, time and pressure. These changes may affect the function
performance lubricants for more than 80 years. of a component. We recommend contacting us to discuss your specific
application. If possible we will be pleased to provide a sample for testing on
request. Klüber products are continually improved. Therefore, Klüber
Lubrication reserves the right to change all the technical data in this document
at any time without notice.
Publisher and Copyright: Klüber Lubrication München SE & Co. KG. Reprints,
total or in part, are permitted only prior consultation with Klüber Lubrication
München SE & Co. KG and if source is indicated and voucher copy is
forwarded.

a company of the Freudenberg Group