Anybus Communicator - PROFIBUS DP Interface Installation Sheet

Module Front LED Indicators Accessories Checklist

LED no Indication Meaning
1 (Online) Green Online
LED Indicators Off Not online The following items are required for installation:
1 2 2 (Offline) Red Offline
Off Not offline
3 (Not used) - - • Anybus Communicator Resource CD (Includes configuration
3 4 4 (Fieldbus Diagnostics) Off No diagnostics present software, manuals, GSD file and application notes)
Red, flashing 1Hz Configuration error • RS232 configuration cable
Red, flashing 2Hz User parameter data error • Subnetwork connector
Red, flashing 4Hz Initialization error
5 6 • PROFIBUS network cable and connector (not included)
5 (Subnet Status) Flashing green Running, but one or more transaction errors
Green Running
A Red Transaction error/timeout or subnet stopped Installation and Startup Summary
Configuration Switches 6 (Device Status) Off Power off
Alternating red/green Invalid or missing configuration
Green Initializing • Mount the Communicator on the DIN-rail.
B Flashing green Running • Connect the Communicator to the PROFIBUS network.
Red Bootloader mode
Flashing red Note the flash sequence pattern and contact • Connect the Communicator to the subnetwork.
the HMS support department • Power on the Communicator (+24 V DC).
• Connect the configuration cable between the Communicator
and the PC containing the Anybus Configuration Manager
PROFIBUS Connector Configuration Switches software (ACM).
A B
• Configure the module using ACM.
Set the PROFIBUS node address by using the switches as follows: • Include the Anybus Communicator GSD file in the
Node address = (switch B * 10) + (switch A * 1) PROFIBUS configuration tool.
• Configure and start the PROFIBUS network.

Switch A 2
Example:
Setting node address 42

Switch B 4

Bottom View
PC Connector: Subnetwork Connector
1. GND Pin no. Description
2. GND
1
PROFIBUS Connector
3. RS232 Rx 1 +5V OUT
4
4. RS232 Tx 2 RS232 Rx Pin no Description
3 RS232 Tx 1 Shield
9
5 5 (female) 1
4 NC 3 B-line

6
5 Signal GND 4 RTS
1

6 RS422 Rx+ 9 6 5 GND bus

Power:
1. +24 V DC 7 RS422 Rx- 6 +5V bus out
1
2. GND 8 RS485+ / RS422 Tx+ 8 A-line
2 Further information and documents about this product can be
9 RS485- / RS422 Tx- 2, 7, 9 NC
found at the product pages on www.anybus.com.

SP0632, rev. 1.20, Mar 2015 www.anybus.com

Anybus Communicator Installation Sheet

UL Certification Additional installation and operating EMC Compliance (CE)

instructions

IND: CONT. EQ.

Max Ambient Temperature: 55°C (for Hazloc environments)
FOR HAZ LOC.
CL I, DIV 2
GP A,B,C,D Field wiring terminal markings (wire type (Cu only, 14-30 AWG)).
TEMP
CODE
E203225
Use 60/75 or 75°C copper (Cu) wire only.

Terminal tightening torque must be between 5-7 lb-in (0.5 - 0.8

Warnings Nm). This product is in accordance with the EMC directive 89/336/EEC,
with amendments 92/31/EEC and 93/68/EEC through conformance
• WARNING - EXPLOSION HAZARD - SUBSTITUTION OF Use in overvoltage category 1 pollution degree 2 environment. with the following standards:
ANY COMPONENTS MAY IMPAIR SUITABILITY FOR
CLASS I, DIVISION 2. Installed in an enclosure considered representative of the in- • EN 50082-2 (1993)
tended use. EN 55011 (1990) Class A
• WARNING - EXPLOSION HAZARD - WHEN IN
HAZARDOUS LOCATIONS, TURN OFF POWER BEFORE Secondary circuit intended to be supplied from an isolating • EN 61000-6-2 (1999)
REPLACING OR WIRING MODULES. source and protected by overcurrent protective devices installed EN 61000-4-3 (1996) 10 V/m
in the field sized per the following: EN 61000-4-6 (1996) 10 V/m (all ports)
• WARNING - EXPLOSION HAZARD - DO NOT EN 61000-4-2 (1995) ±8 kV Air Discharge
Control-circuit Wire Size Maximum Protective Device ±4 kV Contact discharge
DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN
Rating EN 61000-4-4 (1995) ±2 kV Power port
SWITCHED OFF OR THE AREA IS KNOWN TO BE
NONHAZARDOUS. AWG (mm2) Amperes ±1 kV Other ports
22 (0.32) 3 EN 61000-4-5 (1995) ±0.5 kV Power ports (DM/CM)
20 (0.52) 5 ±1 kV Signal ports
18 (0.82) 7
16 (1.3) 10
14 (2.1) 20
Attention! 12 (3.3) 25

• ATTENTION – RISQUE D’EXPLOSION – LE REM-

PLACEMENT DE TOUT COMPOSANTS INVALIDE LA
CERTIFICATION CLASS I, DIVISION 2.

• ATTENTION – RISQUE D’EXPLOSION – EN ZONE

EXPLOSIVE, VEUILLEZ COUPER L’ALIMENTATION
ÉLECTRIQUE AVANT LE REMPLACEMENT OU LE
RACCORDEMENT DES MODULES.

• ATTENTION – RISQUE D’EXPLOSION – NE PAS

DÉCONNECTER L’ÉQUIPEMENT TANT QUE
L’ALIMENTATION EST TOUJOURS PRÉSENTE OU
QUE LE PRODUIT EST TOUJOURS EN ZONE EXPLO-
SIVE ACTIVE.
Further information and documents about this product can be
found at the product pages on www.anybus.com.

www.anybus.com