Manuel S.

Enverga University Foundation

Lucena City, Philippines
Granted Autonomous Status
CHED CEB Res. 076-2009

CE PROJECT (PRACTICUM)
CEAQ5522P

ASSIGNMENT NO. 2
HOW TO PRESENT THE CONCLUSIONS AND RECOMMENDATIONS IN
THE WRITING THE PROJECT STUDY

CASINAS,SHAIRA MAE A. ENGR. EVANGELINE CONSTANTINO

BSCE-V
MWF / 7:30-8:30
APRIL 30, 2020
How to present the conclusions and recommendations in
writing the project study

Conclusions and recommendations

The Conclusions and Recommendations may be combined or, in long reports,
presented in separate sections. If there are no recommendations to be made as a
result of the project, just call this section Conclusions.

The Conclusions section sums up the key points of your discussion, the essential
features of your design, or the significant outcomes of your investigation. As its
function is to round off the story of your project, it should:

 be written to relate directly to the aims of the project as stated in the

Introduction
 indicate the extent to which the aims have been achieved
 summarise the key findings, outcomes or information in your report
 acknowledge limitations and make recommendations for future work (where
applicable)
 highlight the significance or usefulness of your work.

The conclusions should relate to the aims of the work:

Example 1:

Aim

The aim of this project is to design a mobile phone tower for a suburban location..

Conclusions

The mobile phone tower presented here can be erected safely in a suburban street.
It requires a total  area of no more than 2m2 l, and has the following safety features:...

Example 2:

Aim

This investigation will review the volume of passengers using the Monash University
Clayton-Caulfield inter-campus bus in order to recommend adjustments to the
service if needed.

Conclusions

Analysis of the survey data obtained in this project shows that use of the Clayton-
Caulfield inter-campus bus has increased by 24% in the past five years. It is
recommended that frequency be increased during peak usage...

The Conclusions section below is from a level 2 Civil Engineering Alternative

Designs report presenting two designs for a an overpass bridge. Click on the
coloured buttons to see the comments.

Conclusions

Each of the two bridge designs presented in this report fulfil the criteria specified in
the project brief. Both designs incorporate round piers on piled foundations, which
are used because the soil conditions are unknown and possibly unstable. Design 1, a
simple composite I-girder bridge, has the advantage of being made of steel and thus
has longer spans and fewer piers.

Design 2, a super-T beam bridge, requires minimal formwork in the construction of its
concrete deck, is relatively easy to erect and will maintain stability during
transportation and construction. In addition, it is more economical to build and
maintain. Design 2 is therefore recommended. It offers an affordable overpass with
superior durability, and fully meets the requirements of the design brief.

Recommendations
Always address limitations and suggest how they might be overcome in future work.
The excerpt below is from the Conclusions of a report on a project investigating the
effect of pulsation on heat transfer in horizontal pipe flow.

Experimental results showed that pulsed flow without flow reversal had no significant
effect compared with steady flow. Preliminary experiments with reversed flow,
however, clearly indicated increased heat transfer. This is likely due to the large
disturbances in the hydrodynamic boundary layer when the flow changes
direction. Further research is recommended to determine the maximum achievable
enhancement.

It should be noted that the experimental results do not agree with the theoretical
equations. This may be due to the deposits which developed inside the pipe, or to
inconsistent thermocouple temperature. Therefore, regular inspection of the test rig is
recommended.

For a very long report, it is acceptable to present the conclusions and

recommendations in point form:

The prototype robot courier presented here has been shown to be capable of
delivering documents autonomously in an office environment. It has demonstrated
the following components of mobile robotics:

1. Localisation: The Kalman filter-based localisation algorithm achieved sub-

centimeter accuracy under normal operating conditions.
2. Environment modelling: The occupancy map was updated dynamically to
include obstacles not included in the original map.
3. Path planning: A distance transform-based path planner using obstacle
transforms produced a globally optimal local entrapment-free path to the goal.

How to write a good thesis conclusion?

Here are a few points you should keep in mind while writing a thesis conclusion and
recommendation chapters.
Stick to the question

Keep in mind to provide answers to your research problems in your conclusion

chapter. Explain all the problems you have highlighted in the course of your
research. Make sure you provide the readers with answers to these questions with
reference to your research. This will satisfy the readers and will leave them with a
sense of completeness.
Hypothesis

You must keep in mind to address your hypothesis in your thesis conclusion chapter.
There is always a hypothesis a student begins with while writing the dissertation.
Make sure you either confirm that hypothesis or reject it in your conclusion chapter.
You must give out a verdict in your conclusion. That is the whole point behind writing
it. If you don’t give out a verdict, then your entire research is pointless.
Information

You must keep in mind that your conclusion is the summary of your literature. You
must not introduce any new information in your thesis conclusion. This will
completely confuse all your readers since they will be expecting a verdict on your
hypothesis, not a new theory. Not only that, it will also leave a bad impression on
their mind.
Say no to examples

Like we’ve mentioned in the last step, you should not introduce any new facts and
information in your conclusion. Introducing new facts in your conclusion will only
confuse your readers.
No First Person’s

Because your conclusions are all about summarizing all the previously mentioned
facts; you must make sure not to use the first person while writing. You are simply
drawing a conclusion and giving a verdict considering all the facts you have
mentioned in your main body. There is no room whatsoever for personal opinions.
Which is why you shouldn’t use the first person.
Know the difference between conclusion and result

It is important that you understand the difference between a conclusion and a result.
There’s a lot of difference between the two. Do not copy your result into the
conclusion. In the result section, you write about what you have found while
conducting your research. On the other hand, in the conclusion, you discuss your
result and deliver a verdict.
Validate your sources

While recommending, you must make sure that your sources are credible and valid.
Only recommend genuine sources and literature. Otherwise, it might leave a bad
impression on the readers.

Now that you have understood all the points, you are capable of writing a good
conclusion and recommendation chapter. In case you still need professional help or
guidance, you can always opt for Uniresearchers. We have a highly trained and
equipped team which is ready to help you with all your academic writings.

REFERENCES:
https://uniresearchers.co.uk/blogs/thesis-conclusion-and-recommendation-chapter/
https://www.monash.edu/rlo/assignment-samples/engineering/eng-writing-technical-reports/conclusions-and-
recommendations