6014P

3/2-way Direct Mounting Pilot Valve

• Suitable for all Burkert process valves

• Ready for direct mounting
• Reduced power consumption
• Push-over solenoid coil
• Manual override
Type 6014P can be combined with…

Type 2012 Type 1078 Type 2512/2511

Globe valve Timer unit ASI cable plug

The direct acting 3/2-way valve, Type 6014 is Technical data

a specially developed pilot valve for externally
Orifice DN 1.5 and 2.0
controlled actuators. (e.g. Type 2000, 2012,
Material
2030, 2031). It consists of valve Type 6014
Flange body (valve) Brass or polyamide (PA)
with sub-base connection and a banjo bolt Banjo bolt Brass, nickel-plated resp. Aluminium, anodized
connection. Banjo coupler Aluminium
Seal material FKM
With the banjo bolt the valve can be fastened
Media Neutral gases and fluids, compressed air
very simply to the pilot air port of the actuator.
Media temperature 14°F up to 212°F (-10°C up to +100°C)
Ambient temperature Max. 131°F (+55°C)
Circuit function C Voltage tolerance ±10%
Duty cycle 100% continuous rating
Electrical connection Tag connector acc. to DIN EN 175301-803 (previously DIN
3/2-way valve, NC 43650),
Form A for cable plug
Protection class IP 65 with cable plug
Installation As required, preferably with actuator upright

Power consumption
Orifice Inrush AC Hold AC (hot coil) DC (hot coil)
[mm] [VA] [VA] [W] [W]
1.5 11 6 2 2
2.0 24 17 8 8

Response times
Orifice AC DC
[mm] Opening [ms] Closing [ms] Opening [ms] Closing [ms]
1.5 ca. 25 ca. 35 ca. 25 ca. 35
2.0 ca. 18 ca. 22 ca. 18 ca. 22
Response times [ms]:
Measured at valve outlet at 87 PSI and 68°F (+20°C)
Opening: pressure build-up 0 to 90%, closing: pressure relief 100 to 10%

www.burkert–usa.com p. 1/3
 6014P

Ordering chart for valves (other versions on requests)

All valves with FKM seal and manual override, with standard cable plug Type 2508
Anodized aluminium banjo coupler, nickel-plated brass banjo bolt
Item no. per voltage/frequency [V/Hz]

consumption
Orifice [mm]
Service port

flange body
(banjo bolt)

QNn value
air [l/min]
Pressure

Pressure
Material
function

coupler)

024/DC

024/60

120/60

240/60
Circuit

inlet P
(banjo

Power
range
[PSI]

[W]
CV
A
C 3/2-way, normally NPT 1/4 G 1/8 1.5 .08 75 PA 0 – 87 2 429 150 429 151 429 152 429 153
closed (NC) G 1/4 1.5 .08 75 PA 0 – 87 2 429 138 429 139 429 140 429 141
G 1/8 2.0 .13 120 Brass 0 – 145 8 429 146 429 147 429 148 429 149
G 1/4 2.0 .13 120 Brass 0 – 145 8 429 134 429 135 429 136 429 137

I &URTHERôVERSIONSôONôREQUEST

Approvals
ATEX Version (Encapsulation and intrinsically safe)
UR / UL / CSA
Materials
Flange body in stainless steel

Ordering chart for accessory

Cable plug Type 2508 according to DIN EN 175301-803 Form A

Fixing screw
frequency
Voltage /
Circuitry

Item no.

Flat seal

None (standard) 0 - 250 V AC/DC 008 376

further versions see datasheet Type 2508
The delivery of a cable plug includes the flat seal and the fixing screw. For other cable plug versions acc. to DIN EN
175301-803 Form A (previously DIN 43650), see separate datasheet Type 2508.

p. 2/3
 6014P

Dimensions [mm]

Anodized aluminium banjo coupler, nickel-plated brass banjo bolt

45 at 2 W
51 at 8 W
32 at 2 W
40 at 8 W

11.5
57.5

G M L
G 1/8 10 51
G 1/4 12 54

To find your nearest Burkert facility, click on the orange box ➞ www.burkert-usa.com

In case of special application conditions, We reserve the right to make technical changes without notice.
please consult for advice. © Christian Bürkert GmbH & Co. KG 0806/2_US-en_1000084665

p. 3/3