User's Guide

SLUUBA6 – April 2015

bq24780S EVM

The bq24780S evaluation module (EVM) is an SMBus 1- to 4-cell hybrid power boost mode battery
charge controller with power and processor hot monitoring. The input voltage range is between 4.5 V and
24 V, with a programmable output of 1–4 cells charge voltage and 128-mA to 8.128-A charge current. This
EVM does not include the EV2400 interface device; it must be ordered separately to evaluate the
bq24780S EVM.

Contents
1 Introduction ................................................................................................................... 3
1.1 EVM Features ....................................................................................................... 3
1.2 I/O Descriptions ..................................................................................................... 3
1.3 Controls and Key Parameters Setting ........................................................................... 3
1.4 Recommended Operating Conditions ............................................................................ 3
2 Test Summary ................................................................................................................ 4
2.1 Equipment ........................................................................................................... 4
2.2 Equipment Setup.................................................................................................... 5
3 Procedure ..................................................................................................................... 7
3.1 AC Adapter Detection Threshold ................................................................................. 7
3.2 Charger Parameter Settings....................................................................................... 7
3.3 Charge Current and AC Current Regulation (DPM) ............................................................ 7
3.4 Boost Mode .......................................................................................................... 9
3.5 Power Path Selection .............................................................................................. 9
4 PCB Layout Guideline ..................................................................................................... 10
5 Board Layout, Schematic, and Bill of Materials ........................................................................ 11
5.1 PWR583 PCB Layouts ........................................................................................... 11
5.2 Schematics ......................................................................................................... 14
5.3 Bill of Materials .................................................................................................... 15

List of Figures
1 Connections of the EV2400 Kit ............................................................................................ 5
2 Original Test Setup for PWR583 (bq24780S EVM) ..................................................................... 6
3 Main Window of bq24780S Evaluation Software ........................................................................ 6
4 Test Setup for PWR583 ..................................................................................................... 8
5 Top Assembly ............................................................................................................... 11
6 Top Layer.................................................................................................................... 11
7 Mid-Layer 1................................................................................................................. 12
8 Mid-Layer 2................................................................................................................. 12
9 Bottom Layer ................................................................................................................ 13
10 Bottom Assembly ........................................................................................................... 13
11 bq24780SEVM-583 Schematic ........................................................................................... 14

List of Tables
1 I/O Descriptions .............................................................................................................. 3
2 Controls and Key Parameters Setting .................................................................................... 3
3 Recommended Operating Conditions ..................................................................................... 3
Microsoft, Windows are registered trademarks of Microsoft Corporation.

SLUUBA6 – April 2015 bq24780S EVM 1

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
 www.ti.com

4 EV2400 and bq24780S EVM Connections ............................................................................... 5

5 bq24780SEVM-583 Bill of Materials ..................................................................................... 15

2 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Introduction

1 Introduction

1.1 EVM Features

Refer to the data sheet (SLUSC27) for detailed features and operation.

1.2 I/O Descriptions

Table 1 lists the I/O descriptions.

Table 1. I/O Descriptions

Jack Description
J1– DCIN Connect to AC adapter positive output
J1– GND Connect to AC adapter, negative output
J2 – SYS Connect to system
J2 – GND Power ground, same as J1 – GND
J2 – BAT Connect to battery positive
J3 – 1 GND Analog ground
J3 – 2 SDA
Communication interface
J3 – 3 SCL
J3 – 4 3V3 External 3.3-V power supply
J3 – 5 CMPIN Integrated comparator input (pin 13)
J3 – 6 CMPOUT Integrated comparator output (pin 14)

1.3 Controls and Key Parameters Setting

Table 2 lists the controls and key parameter settings of the EVM.

Table 2. Controls and Key Parameters Setting

Jack Description Factory Setting
Connect battery positive input (BAT) to TPS3898 SENSE pin through resistor
JP1 Jumper not installed
divider (R33/R34)
JP2 Connect REGN to TPS3898 VCC pin Jumper not installed
JP3 Connect BAT to bq24780 CMPIN pin through resistor divider (R35/R36) Jumper not installed
JP4 Connect bq24780 CMPOUT to bq24780/BATPRES pin Jumper not installed
JP5 Connect TPS3898/SENSE_OUT pin to bq24780/BATPRES pin Jumper not installed
JP6 Connect battery positive input (BAT) to diode D1 Jumper Installed

1.4 Recommended Operating Conditions

Table 3 provides the recommended operating conditions.

Table 3. Recommended Operating Conditions

Description MIN TYP MAX UNIT
VIN (1) Supply voltage Input voltage from AC adapter input 18 19–20 23 V
VBAT Battery voltage Voltage applied at VBAT terminal 3–16.8 17.408 V
IAC Supply current Maximum input current from AC adapter input 4.5 A
IS Output current Output current (SYS and CHG) 8 A
TJ Operating junction temperature range 0 125 °C
(1)
ACDET bias, R5 and R6, is set for this range. For lower adapter voltages, this divider has to be modified. With the proper bias,
VIN MIN can be as low as 4.5 VDC. See the data sheet (SLUSC27) for more information.

SLUUBA6 – April 2015 bq24780S EVM 3

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Test Summary www.ti.com

2 Test Summary
Section 2.1 and Section 2.2 explain the equipment and the equipment setup.

2.1 Equipment

2.1.1 Power Supplies

Power Supply #1 (PS#1): a power supply capable of supplying 20 V at 5 A is required.
Power Supply #2 (PS#2): a power supply capable of supplying 5 V at 1 A is required.
Power Supply #3 (PS#3): a power supply capable of supplying 20 V at 3 A is required.

2.1.2 Loads
LOAD #1: A 30 V (or above), 5-A (or above) electronic load that can operate at constant current mode.
LOAD #2: An HP 6060B 3–60 V/0–60 A, 300-W system DC electronic load, or equivalent.

2.1.3 Meters
Seven Fluke 75 multimeters, (equivalent or better), or four equivalent voltage meters and three equivalent
current meters.
The current meters must be capable of measuring 5 A+ current.

2.1.4 Computer
A computer with at least one USB port and a USB cable. The EV2400 USB driver and the bq24780 SMB
evaluation software must be properly installed.

2.1.5 SMBUS Communication Kit

This EVM is compatible with both the EV2400 and EV2300 hardware kit. TI recommends using the
EV2400 hardware kit.

2.1.6 Install Battery Management Studio (bqStudio) Software

Double click the Battery Management Studio software installation file, follow the installation steps.

2.1.7 Upon First Insertion of EV2400 Into USB Port of PC

Follow the instructions of the Found New Hardware Wizard
• Allow Microsoft® Windows® to connect to Windows Update to search for software, then click Next
• Select Install software automatically (Recommended), then click Next
• If a window pops up informing that the TI USB Firmware Updater has not passed Windows Logo
testing click Continue Anyway
• If a target file already exists and is newer, do not overwrite the newer file
• Click Finish

4 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Test Summary

2.2 Equipment Setup

• Set power supply #1 (PS#1) for 0 V ±100 mVDC, with the current limit set to > 5 A. Turn off supply.
• Connect PS#1 output in series with a current meter (multimeter) to J1 (VIN, GND)
• Connect a voltage meter across J1 (VIN, GND)
• Set power supply #2 (PS#2) for 3.3 V ±100 mVDC, with the current limit set to > 0.2 A. Turn off supply.
• Connect PS#2 output to J3 (3V3, GND)
• Connect a voltage meter across J2 (BAT, GND)
• Connect a voltage meter across J2 (SYS, GND)
• Connect J3 (SDA, SCL) and J3 (GND) to the EV2400 kit SMB port. Refer to Table 4 for EVM
connections. Connect the USB port of the EV2400 kit to the USB port of the computer. The
connections are shown in Figure 2.

Table 4. EV2400 and bq24780S EVM Connections

bq24780S EVM EV2400
GND (J3) VSS 1.1
SCL (J3) SCL 1.2
SDA (J3) SDA 1.3

Figure 1. Connections of the EV2400 Kit

SLUUBA6 – April 2015 bq24780S EVM 5

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Test Summary www.ti.com

After completing the previous steps, the test setup for PWR583 appears as shown in Figure 2.

Figure 2. Original Test Setup for PWR583 (bq24780S EVM)

Turn on the computer. Launch the bqstudio evaluation software and select charger and bq24780S. And
then click the Registers button. The main window of the bq24780S software is shown in Figure 3.

Figure 3. Main Window of bq24780S Evaluation Software

6 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Procedure

3 Procedure

3.1 AC Adapter Detection Threshold

Use the following steps for AC adapter detection threshold:
1. Ensure Equipment Setup steps are followed. Turn on PS#2.

NOTE: Load #1 and Load #2 are not connected during this step.

2. Turn on PS#1
3. Increase the output voltage of PS#1 to 19.5 V
• Measure → V[TP(ACDET)] = 2.6 V ±0.1 V
• Measure → V[TP(ACOK)] = 3.3 V ±0.1 V
• Measure → V[J2(SYS)] = 19.5 V ±0.5 V
• Measure → V[TP(REGN)] = 5.4 V ±0.5 V
• Measure → V[TP(ACDRV, CMSRC)] = 6 V ±0.5 V
• Measure → V[J2(BAT, GND)] = 2 V ±2 V

3.2 Charger Parameter Settings

In the main software window, click the Refresh button on the top right corner. Make sure there is no error
information.
Type “512” (mA) in ChargeCurrent Register and click OK. This sets the battery charge current regulation
threshold.
Type “12592” (mV) in ChargeVoltage Register and click OK. This sets the battery voltage regulation
threshold:
• Measure → V(J2(BAT)) = 12.6 V ±200 mV

3.3 Charge Current and AC Current Regulation (DPM)

1. Connect Load #2 in series with a current meter (multimeter) to J2 (BAT, GND). Make sure a voltage
meter is connected across J2 (BAT, GND). Turn on Load #2. Use the constant voltage mode. Set
output voltage to 10.5 V.
2. Connect the output of Load #1 in series with a current meter (multimeter) to J2 (SYS, GND). Make
sure a voltage meter is connected across J2 (SYS, GND). Turn on the power of Load #1.
The setup is now like Figure 4 for PWR583.

SLUUBA6 – April 2015 bq24780S EVM 7

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Procedure www.ti.com

Figure 4. Test Setup for PWR583

3. Type “2944” (mA) in ChargeCurrent Register and click OK.

This sets the battery charge current regulation threshold to 2.944 A.
• Measure → IBAT = 3000 mA ±300 mA
• Measure → V[TP(IIADP)] = 340 mV ±40 mV
4. Set Load #1 current to 3.0 A ±50 mA but disable the output. Make sure ISYS = 0 A ±10 mA. Enable
the output of Load #1.
• Measure → ISYS = 3000 mA ±300 mA
• Measure → IBAT = 1800 mA ±300 mA
• Measure → IIN = 4100 mA ±400 mA
• Measure → V[TP(IIADP]) = 820 mV ±100 mV
5. Turn off the Load #1.
• Measure → ISYS = 0 ±100 mA
• IBAT = 3000 mA ±300 mA

8 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Procedure

3.4 Boost Mode

Use the following steps for boost mode:
1. Enter “1A44” in ChargeOption3 value to enable the turbo boost function
2. Change Load #2 with PS#3. Make sure a voltage meter is connected across J2 (BAT, GND).
3. Enable the output of PS#3. Make sure the output voltage is 10 V ±500 mV and 3-A current limit.
4. Set Load #1 load current to 5.0 A ±50 mA. Enter boost mode.
• Measure → ISYS = 5000 mA ±500 mA
• Measure → IBAT = –1700 mA ±300 mA
• Measure → IIN = 4100 mA ±400 mA
• Measure → V[TP(IIADP)] = 820 mV ±100 mV
• Measure → V[TP(IIDCHG)] = 270 mV±100 mV
5. Set Load #1 load current to 0.5 A ±50 mA. Exit boost mode. Back to charging mode.
• Measure → ISYS = 500 mA ±50 mA
• Measure → IBAT = 3000 mA ±300 mA
• Measure → IIN = 2100 mA ±400 mA

3.5 Power Path Selection

The setup for power path selection follows:
1. Change Load #2 with PS#3. Make sure a voltage meter is connected across J2 (BAT, GND)
2. Enable the output of PS#3. Ensure the output voltage is 10 V ±500 mV and 3-A current limit.
3. Set Load #1 load current to 0.5 A ±50 mA
4. Enter “E109” in ChargeOption0, this disables charging
5. Make sure a voltage meter is connected across J2 (BAT, GND)
• Measure → V(J2(SYS)) = 19.5 V ±1 V (adapter connected to system)
6. Turn off PS#1
• Measure → V[J2(SYS)] = 10 V ±1 V (battery connected to system)
• Measure → V[J2(BAT)] = 10 V ±1 V (battery connected to system)

SLUUBA6 – April 2015 bq24780S EVM 9

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
PCB Layout Guideline www.ti.com

4 PCB Layout Guideline

The switching node rise and fall times should be minimized for minimum switching loss. Proper layout of
the components to minimize high frequency current path loop is important to prevent electrical and
magnetic field radiation and high-frequency resonant problems. Here is a PCB layout priority list for proper
layout. Layout of the PCB according to this specific order is essential.
1. Place input capacitor as close as possible to switching MOSFET’s supply and ground connections and
use the shortest possible copper trace connection. These parts should be placed on the same layer of
PCB instead of on different layers and using vias to make this connection.
2. The IC should be placed close to the switching MOSFET’s gate pins and keep the gate drive signal
traces short for a clean MOSFET drive. The IC can be placed on the other side of the PCB from the
switching MOSFETs.
3. Place the inductor input pin to the switching MOSFET’s output pin as close as possible. Minimize the
copper area of this trace to lower electrical and magnetic field radiation but make the trace wide
enough to carry the charging current. Do not use multiple layers in parallel for this connection.
Minimize parasitic capacitance from this area to any other trace or plane.
4. The charging current sensing resistor should be placed right next to the inductor output. Route the
sense leads connected across the sensing resistor back to the IC in same layer, close to each other
(minimize loop area) and do not route the sense leads through a high-current path. Place decoupling
capacitor on these traces next to the IC.
5. Place the output capacitor next to the sensing resistor output and ground.
6. Output capacitor ground connections need to be tied to the same copper that connects to the input
capacitor ground before connecting to system ground.
7. Use a single ground connection to tie charger power ground to charger analog ground. Just beneath
the IC, use analog ground copper pour but avoid power pins to reduce inductive and capacitive noise
coupling.
8. Route analog ground separately from power ground. Connect analog ground and connect power
ground separately. Connect analog ground and power ground together using the power pad as the
single ground connection point or using a 0-Ω resistor to tie analog ground to power ground (power
pad should tie to analog ground in this case, if possible).
9. Decoupling capacitors should be placed next to the IC pins and make the trace connection as short as
possible.
10. It is critical that the exposed power pad on the backside of the IC package be soldered to the PCB
ground. Ensure that there are sufficient thermal vias directly under the IC, connecting to the ground
plane on the other layers.
11. The via size and number should be enough for a given current path.
See the EVM design for the recommended component placement with trace and via locations. For the
WQFN information, see SCBA017 and SLUA271.

10 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Board Layout, Schematic, and Bill of Materials

5 Board Layout, Schematic, and Bill of Materials

This section contains the PWR583 PCB layouts, schematics, and bill of materials.

5.1 PWR583 PCB Layouts

Figure 5 through Figure 10 show the PCB layouts for the PWR583 EVM.

Figure 5. Top Assembly

Figure 6. Top Layer

SLUUBA6 – April 2015 bq24780S EVM 11

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Board Layout, Schematic, and Bill of Materials www.ti.com

Figure 7. Mid-Layer 1

Figure 8. Mid-Layer 2

12 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Board Layout, Schematic, and Bill of Materials

Figure 9. Bottom Layer

Figure 10. Bottom Assembly

SLUUBA6 – April 2015 bq24780S EVM 13

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Board Layout, Schematic, and Bill of Materials www.ti.com

5.2 Schematics
The bq24780SEVM-583 (Figure 11) schematic is provided for reference.
1 TP1
R5 Q7
BSS138W-7-F DNP
1.00Meg

5
4
3
2
50V
R6
4.5 ~ 24V
PGND 3.01Meg
VIN Q6
PGND
Q3 DNP
R8 30V 30V
SYS
7,8 1,2,3 1,2,3 7,8

5,6,

5,6,
0.01

7,8

7,8
5,6, Q1 5,6,
J1 4 4 C11
30V Q2 C15 C2 C3 C4 C5 DNP C10 DNPDNP J2

5,6,
C1 30V Q4

7,8

1,2,3

1,2,3
C16 1µF 10µF 10µF 10µF 10µF 22µF
2.2µF HIDRV
4 30V
R3 C27
0.01µF

1,2,3
430k 0.1µF DNPC23
PHASE
C12 R7 C13 PGND DNP PGND PGND
1000pF 4.7 0.047µF
BTST R19 R23
BAT
R1 R2 6.8 0.01
3.9 3.9 D2 C24
L1
REGN DNP 0.047µF
DNPC17 C18 C19 D9 DNP IHLP3232DZER3R3M01
R4 DNP 0.1µF 0.1µF VCC 3.3µH C6 C7 DNPC8 DNPC9 DNP D8
66.5k DNP 10µF 10µF DNP DNP
C21 DNP
JP6
DNP C28
PGND
LODRV
GND GND C20 2.2µF
D1 PGND D7 1µF 0.1µF
R15 R16 R20
BAT GND PGND

5,6,
0

7,8
0 100k DNPC26
R12 R13

28

27

26

25

24

23

22
30V 30V 4 Q5 DNP
4.02k 4.02k PGND GND C29 C30
C22

1,2,3
R21 30V R25 0.1uF 0.1µF

PHASE
VCC

HIDRV

LODRV
REGN

GND
PAD

BTST
0.01µF 316k C25 DNP
DNP
470pF
ACDRV

CMSRC

R17

ACN
ACP
3V3
10.0 21
ILIM ILIM
1 ACN
PGND GND
R14 SRP R26
SRP 20
DNP
2 ACP 10.0
DNP U1 SRN R27
SRN 19
3V3
3 CMSRC
BQ24780SRUY 10.0
VCC BATDRV R28
R11 GND BATDRV 18
10.0k 4 ACDRV 4.02k
BATSRC R29
BATSRC 17
5 ACOK 10.0
ACOK
TB_STAT 16
TB_STAT
6 ACDET
15 R10
BATPRES BATPRES DNP
DNPC14 7 DNP

PROCHOT
ACDET IADP
R41

CMPOUT
DNP

IDCHG

CMPIN
10.0k

PMON
ILIM

SDA

SCL
JP1
GND
IADP
3V3

10

12

13

14
8

11
IDCHG
JP4 BAT
PMON REGN JP2
JP5
R33 R35
R47
C31 C32 DNPC33 R45 R31 499k 140k
30.1k
100pF 100pF 100pF 1.00Meg 10.0k U2
3V3
4 3
J3 SENSE_OUT SENSE
CMPOUT
JP3
5 2
CT GND
6 CMPIN R46 R37 R39 R40 GND
PROCHOT

5 PGND C37 10.0k 10.0k 10.0k 10.0k 6 1

CMPOUT
VCC ENABLE

CMPIN
4 3V3 2.2µF
R9
3 NT1 C34 C35 R32 R34 R36
10.0k TPS3898ADRY
2 SCL Net-Tie 2200pF 0.1µF 10.0k 49.9k 100k
SCL
1
SDA
SDA
GND
GND GND
GND

GND
3V3
Q8
R38 R42 R30 R44 2N7002ET1G
2.00k 2.00k 2.00k 2.00k 60V

TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9 TP10 TP11 TP12 TP13 TP14 TP15 TP16 TP17 ACOK

D5 D4 D6 D3
Orange Green Orange Green
CMSRC IDCHG ILIM

ACDRV PMON BATDRV

GND
PROCHOT BATPRES TB_STAT
ACDET PROCHOT REGN

ACOK BATPRES GND

IADP TB_STAT VCC

Figure 11. bq24780SEVM-583 Schematic

14 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com Board Layout, Schematic, and Bill of Materials

5.3 Bill of Materials

Table 5 lists the bq24780SEVM-583 BOM.

Table 5. bq24780SEVM-583 Bill of Materials

Designator Qty Value Description Package PartNumber Manufacturer
Reference
!PCB 1 Printed Circuit Board PWR583 Any
C1 1 2.2uF CAP, CERM, 2.2uF, 25V, +/-10%, X7R, 1206 1206 GRM31MR71E225KA93L MuRata
C2, C3, C4, C5, C6, C7 6 10uF CAP, CERM, 10uF, 25V, +/-10%, X5R, 1206 1206 GRM31CR61E106KA12L MuRata
C10 1 22uF CAP, CERM, 22uF, 25V, +/-10%, X5R, 1210 1210 GRM32ER61E226KE15L MuRata
C12 1 1000pF CAP, CERM, 1000pF, 50V, +/-10%, X7R, 0603 GRM188R71H102KA01D MuRata
0603
C13, C24 2 0.047uF CAP, CERM, 0.047uF, 50V, +/-10%, X7R, 0603 GRM188R71H473KA61D MuRata
0603
C15, C20 2 1uF CAP, CERM, 1uF, 25V, +/-10%, X7R, 0603 0603 GRM188R71E105KA12D MuRata
C16, C18, C19, C28, C29, 7 0.1uF CAP, CERM, 0.1uF, 25V, +/-10%, X7R, 0603 0603 GRM188R71E104KA01D MuRata
C30, C35
C21 1 2.2uF CAP, CERM, 2.2uF, 16V, +/-10%, X5R, 0603 0603 GRM188R61C225KE15D MuRata
C22, C27 2 0.01uF CAP, CERM, 0.01uF, 50V, +/-10%, X7R, 0603 C0603X103K5RACTU Kemet
0603
C25 1 470pF CAP, CERM, 470pF, 50V, +/-10%, X7R, 0603 0603 GRM188R71H471KA01D MuRata
C31, C32 2 100pF CAP, CERM, 100pF, 50V, +/-5%, C0G/NP0, 0603 C0603C101J5GAC Kemet
0603
C34 1 2200pF CAP, CERM, 2200pF, 50V, +/-5%, C0G/NP0, 0805 C2012C0G1H222J TDK
0805
C37 1 2.2uF CAP, CERM, 2.2uF, 10V, +/-10%, X7R, 0603 0603 GRM188R71A225KE15D MuRata
D1, D7 2 30V Diode, Schottky, 30V, 0.2A, SOD-323 SOD-323 BAT54HT1G ON Semiconductor
D3, D4 2 Green LED, Green, SMD 1.6x0.8x0.8mm LTST-C190GKT Lite-On
D5, D6 2 Orange LED, Orange, SMD 1.6x0.8x0.8mm LTST-C190KFKT Lite-On
H9, H10, H11, H12 4 Bumpon, Hemisphere, 0.44 X 0.20, Clear Transparent SJ-5303 (CLEAR) 3M
Bumpon
J1 1 TERMINAL BLOCK 5.08MM VERT 2POS TERM_BLK, 2pos, ED120/2DS On-Shore
5.08mm Technology, Inc.
J2 1 TERMINAL BLOCK 5.08MM VERT 3POS TERM_BLK, 3pos, ED120/3DS On-Shore
5.08mm Technology, Inc.
J3 1 Terminal Block, 6A, 3.5mm Pitch, 6-Pos, TH 20.5x8.2x6.5mm ED555/6DS On-Shore
Technology, Inc.
JP1, JP2, JP3, JP4, JP5, 6 Header, 100mil, 2x1, Gold plated, TH Header, 2x1, 5-146261-1 TE Connectivity
JP6 100mil
L1 1 3.3uH Inductor, Shielded, Powdered Iron, 3.3uH, 322x158x322mil IHLP3232DZER3R3M01 Vishay-Dale
9.2A, 17.7 ohm, SMD
LBL1 1 Thermal Transfer Printable Labels, 0.650" W PCB Label THT-14-423-10 Brady
x 0.200" H - 10,000 per roll 0.650"H x 0.200"W
Q1, Q2, Q3, Q4, Q5 5 30V MOSFET, N-CH, 30V, 47A, SON 3.3x3.3mm SON 3.3x3.3mm CSD17308Q3 Texas Instruments
Q7 1 50V MOSFET, N-CH, 50V, 0.2A, SOT-323 SOT-323 BSS138W-7-F Diodes Inc.
Q8 1 60V MOSFET, N-CH, 60V, 0.26A, SOT-23 SOT-23 2N7002ET1G ON Semiconductor
R1, R2 2 3.9 RES, 3.9 ohm, 5%, 0.5W, 1210 1210 ERJ-14YJ3R9U Panasonic
R3 1 430k RES, 430k ohm, 1%, 0.1W, 0603 0603 RC0603FR-07430KL Yageo America
R4 1 66.5k RES, 66.5k ohm, 1%, 0.1W, 0603 0603 CRCW060366K5FKEA Vishay-Dale
R5, R45 2 1.00Meg RES, 1.00Meg ohm, 1%, 0.1W, 0603 0603 CRCW06031M00FKEA Vishay-Dale
R6 1 3.01Meg RES, 3.01Meg ohm, 1%, 0.1W, 0603 0603 CRCW06033M01FKEA Vishay-Dale
R7 1 4.7 RES, 4.7 ohm, 5%, 0.1W, 0603 0603 CRCW06034R70JNEA Vishay-Dale
R8, R23 2 0.01 RES, 0.01 ohm, 1%, 1W, 1206 1206 WSLP1206R0100FEA Vishay-Dale
R9, R11, R31, R32, R37, 9 10.0k RES, 10.0k ohm, 1%, 0.1W, 0603 0603 CRCW060310K0FKEA Vishay-Dale
R39, R40, R41, R46
R12, R13, R28 3 4.02k RES, 4.02k ohm, 1%, 0.1W, 0603 0603 CRCW06034K02FKEA Vishay-Dale
R15, R16 2 0 RES, 0 ohm, 5%, 0.1W, 0603 0603 CRCW06030000Z0EA Vishay-Dale
R17 1 10.0 RES, 10.0 ohm, 1%, 0.25W, 1206 1206 ERJ-8ENF10R0V Panasonic
R19 1 6.8 RES, 6.8 ohm, 5%, 0.1W, 0603 0603 CRCW06036R80JNEA Vishay-Dale
R20, R36 2 100k RES, 100k ohm, 5%, 0.1W, 0603 0603 CRCW0603100KJNEA Vishay-Dale
R21 1 316k RES, 316k ohm, 1%, 0.1W, 0603 0603 CRCW0603316KFKEA Vishay-Dale
R26, R27, R29 3 10.0 RES, 10.0 ohm, 1%, 0.1W, 0603 0603 RC0603FR-0710RL Yageo America
R30, R38, R42, R44 4 2.00k RES, 2.00k ohm, 1%, 0.1W, 0603 0603 CRCW06032K00FKEA Vishay-Dale
R33 1 499k RES, 499k ohm, 1%, 0.1W, 0603 0603 CRCW0603499KFKEA Vishay-Dale

SLUUBA6 – April 2015 bq24780S EVM 15

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Board Layout, Schematic, and Bill of Materials www.ti.com

Table 5. bq24780SEVM-583 Bill of Materials (continued)

Designator Qty Value Description Package PartNumber Manufacturer
Reference
R34 1 49.9k RES, 49.9k ohm, 1%, 0.1W, 0603 0603 CRCW060349K9FKEA Vishay-Dale
R35 1 140k RES, 140k ohm, 1%, 0.1W, 0603 0603 CRCW0603140KFKEA Vishay-Dale
R47 1 30.1k RES, 30.1k ohm, 1%, 0.1W, 0603 0603 CRCW060330K1FKEA Vishay-Dale
TP2, TP3, TP4, TP5, TP6, 13 White Test Point, TH, Miniature, White Keystone5002 5002 Keystone
TP7, TP8, TP9, TP10,
TP11, TP12, TP13, TP17
TP14 1 Orange Test Point, Miniature, Orange, TH Orange Miniature 5003 Keystone
Testpoint
TP15, TP16 2 Black Test Point, Miniature, Black, TH Black Miniature 5001 Keystone
Testpoint
U1 1 1-4 Cell Turbo Boost Mode Battery Charge RUY0028A BQ24780SRUY Texas Instruments
Controller with Power Monitoring and
/PROCHOT for CPU Throttling, RUY0028A
U2 1 Single-Channel, Adjustable Supervisory DRY0006A TPS3898ADRY Texas Instruments
Circuit in Ultra-Small Package, DRY0006A
C8, C9 0 10uF CAP, CERM, 10uF, 25V, +/-10%, X5R, 1206 1206 GRM31CR61E106KA12L MuRata
C11 0 150uF CAP, TA, 150uF, 16V, +/-20%, 0.05 ohm, 7.3x2.8x4.3mm 16TQC150MYF Panasonic
SMD
C14, C26 0 DNP CAP, CERM, 0.1uF, 25V, +/-10%, X7R, 0603 0603 GRM188R71E104KA01D MuRata
C17 0 1uF CAP, CERM, 1uF, 25V, +/-10%, X7R, 0603 0603 GRM188R71E105KA12D MuRata
C23 0 0.1uF CAP, CERM, 0.1uF, 25V, +/-10%, X7R, 0603 0603 GRM188R71E104KA01D MuRata
C33 0 100pF CAP, CERM, 100pF, 50V, +/-5%, C0G/NP0, 0603 C0603C101J5GAC Kemet
0603
D2 0 DNP Diode, Schottky, 30V, 0.2A, SOD-323 SOD-323 BAT54HT1G ON Semiconductor
D8 0 DNP Diode, Schottky, 20V, 1A, SMA SMA SS12-E3/61T Vishay-
Semiconductor
D9 0 8.2V Diode, Zener, 8.2V, 500mW, SOD-123 SOD-123 BZT52C8V2-7-F Diodes Inc.
FID1, FID2, FID3 0 Fiducial mark. There is nothing to buy or Fiducial N/A N/A
mount.
H1, H2, H3, H4 0 Machine Screw, Round, #4-40 x 1/4, Nylon, Screw NY PMS 440 0025 PH B&F Fastener
Philips panhead Supply
H5, H6, H7, H8 0 Standoff, Hex, 0.5"L #4-40 Nylon Standoff 1902C Keystone
Q6 0 30V MOSFET, N-CH, 30V, 47A, SON 3.3x3.3mm SON 3.3x3.3mm CSD17308Q3 Texas Instruments
R10 0 DNP RES, 84.5k ohm, 0.1%, 0.1W, 0603 0603 RG1608P-8452-B-T5 Susumu Co Ltd
R14 0 DNP RES, 0 ohm, 5%, 0.1W, 0603 0603 CRCW06030000Z0EA Vishay-Dale
R25 0 DNP RES, 100k ohm, 1%, 0.1W, 0603 0603 CRCW0603100KFKEA Vishay-Dale
TP1 0 Compact Probe Tip Circuit Board Test Points, TH Scope Probe 131-5031-00 Tektronix
TH, 25 per

16 bq24780S EVM SLUUBA6 – April 2015

Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
 STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.

2 Limited Warranty and Related Remedies/Disclaimers:

2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.

3 Regulatory Notices:
3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:

CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.

FCC Interference Statement for Class A EVM devices

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
 FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

3.2 Canada
3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.

Concernant les EVMs avec appareils radio:

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Concerning EVMs Including Detachable Antennas:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page

3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。

なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル

3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4 EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.

5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
 SPACER
6. Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.

7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.

8. Limitations on Damages and Liability:

8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.

9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.

10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated

spacer
 IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated