s A6V10889954 Mounting and dismounting /

en Mounting instructions zh

Fan coil room thermostat

RDF510…, RDF530…

Installation live demo Datasheet

Mounting location of thermostat / Wiring diagrams /

RDF510… en ) zh ( )
AC 230 V power supply, mains and
L, N AC 230 V
neutral
Q1, SPST relay outputs for fan speed (Q1)
Q2, Q3 low (Q1), medium (Q2), high (Q3) (Q2) (Q3)
N1 RDF510… RDF510…
N2 RDF530… RDF530…
M 3-speed fan motor
V1, V2 Valves
Y1, Y2 SPST relay output, normally open
Y12 SPDT relay output, normally closed
Y14 SPDT relay output, normally open
T 6.3 A Internal fuse (6.3 A), replaceable (6.3 A)
Dimensions (mm) / ( )
Connect only one fan at a time to Q
View A / A View B / B RDF530… output Q on the thermostat

Do not connect Y12 to either L or N, Y12

or use Y12 as AC 230 V power
supply Y12 AC 230 V

Internal fuse (replaceable) /

Fuse type / SLOW-BLOW /
Size / 5.2 x 20 mm
Voltage rating / 250 V
Current rating / 6.3 A

The fuse supports a total maximum loading (fan and valve) of 5 A.

Above are the dimensions for the thermostat and its mounting plate. 5A

Siemens Building Technologies RDF510…, RDF530… A6V10889954_c 2018-03-27 1/2

en Operating instructions zh RDF510…, RDF530…
Overview /
1) Timer with delay Off /
If P28=0 (factory setting), press for more than 3 seconds to
set the on-time duration each time. If P28=1, 2, 3 up to 23 hours,
preset with a fixed on-time, countdown begins once the
thermostat is ON (refer to Parameter list below).
P28=0 3
P28 1 23

2) Manual heating/cooling changeover /

With manual changeover (P01=2), symbols / indicate the
current control sequence selected. i.e. heating or cooling mode.
/ P01=2 , /

Changing control parameters /

Press + and – simultaneously for 3 seconds. / + –3
Within 2 seconds, press + for 3 seconds to go to the parameter access mode.
2 +3
Press < or > to select the desired parameter. / < >
Press ü to edit the parameter, then use + and – to change its value.
ü + –
Press ü to confirm the change, then continue to select/edit other parameters/values.
ü / /
Press to exit parameter access mode. /

Parameter list /
Parameter Description Factory setting Setting range Adj.
!
P01 Control sequence / RDF510… = 2 0:= Heating only / 4:= Heating and cooling /
RDF530… = 4 1:= Cooling only /
2:= H/C changeover manual / / RDF510…: 0, 1, 2; RDF530…: 2, 4
P05 Sensor calibration / 0K -5 … +5 K
P06 Standard temperature display / 0 0:= Room temperature / 1:= Setpoint /
P09 Minimum setpoint in Comfort mode / 5 °C 5 …40 °C
P10 Maximum setpoint in Comfort mode / 35 °C 5 …40 °C
P14 Keylock function / 0 0:= No lock / 1:= Full lock / 2:= Partial lock /
P15 Fan control deadzone in Comfort mode / / 1 0:= Fan off /
1:= Fan speed 1 in heating or cooling mode /
P27 Operating mode settings upon power down 0 0:= Return to previous operating mode or user settings /
1:= Protection mode /
P28 Timer with delay Off / 0 0:= Users to set on-time duration /
1 to 23:= Preset with a fixed on-time in hours /
P30 Switching differential in heating mode / 1K 0.5…6 K
P31 Switching differential in cooling mode / 1K 0.5...6 K
P33 Deadzone in Comfort mode / / 2K 0.5...5 K (RDF530)
P59 Fan minimum on-time (dwelling time) / ( ) 2 minutes / 2 1...6 minutes / 1 ... 6
P65 Protection heating setpoint / 8°C OFF, 5°C…Wcoolpro; Wcoolpro=40°C max.
P66 Protection cooling setpoint / OFF / OFF, Wheatpro…40°C; Wheatpro=5°C min.
P71 Reload factory setting / OFF / OFF:= Disable / ; ON:= Reload start /
“---” is displayed for 3 seconds during reload process / “---” 3
! Please record all changes you make. /
To download the latest documentations and applications, go to: / https://www.downloads.siemens.com/download-center/
Subject to change.
2/2 2018-03-27 A6V10889954_c RDF510..., RDF530... Siemens Building Technologies