Scribd
Upload
77 views

The University of Lahore, Islamabad Campus Course: Power System Protection Lab Work Sheet 3

This document provides instructions for a lab experiment involving modeling and implementing a three-phase power system using Simpower system components. The objectives are to study Simpower system behavior/characteristics and implement components to understand their results. The document describes several three-phase components - a voltage source, series RLC branch, transformer, voltage/current measurement block, and RLC load. It includes the theory of operation for each component. Students are tasked with using Simpower system to build the circuits shown in two figures, completing all activities and tasks, and writing a summary. Late submissions will result in reduced marks.

Uploaded by

Hayat Ansari
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
77 views

The University of Lahore, Islamabad Campus Course: Power System Protection Lab Work Sheet 3

This document provides instructions for a lab experiment involving modeling and implementing a three-phase power system using Simpower system components. The objectives are to study Simpower system behavior/characteristics and implement components to understand their results. The document describes several three-phase components - a voltage source, series RLC branch, transformer, voltage/current measurement block, and RLC load. It includes the theory of operation for each component. Students are tasked with using Simpower system to build the circuits shown in two figures, completing all activities and tasks, and writing a summary. Late submissions will result in reduced marks.

Uploaded by

Hayat Ansari
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

THE UNIVERSITY OF LAHORE,ISLAMABAD CAMPUS

COURSE: POWER SYSTEM PROTECTION


Lab Work Sheet 3

Student Name:________________

Reg No: _____________________

Date: _______________________

Marks obtained: ____________________

Checked date: _______________

Instructions:
 Complete all activities in lab and get checked by the lab engineer.
 Home task should be completed before next lab and must checked by the lab engineer.
 At the end of all activities and home task students advised to write a summary in their own words.
 Late submission will lead to deduction of marks.
 Date must be properly mentioned.
LAB EAXPERIMENT NO: 3

Modeling and Implementation of a Simpower System Using Three Phase Components

OBJECTIVE:-

•To study the behavior and characteristics of Simpower system.

•Implement the components and know their results.

THEORY:- (Three phase source)

The Three-Phase Source block implements a balanced three-phase voltage source with an
internal R-L impedance. The three voltage sources are connected in Y with a neutral connection
that can be internally grounded or made accessible. You can specify the source internal
resistance and inductance either directly by entering R and L values or indirectly by specifying
the source inductive short-circuit level and X/R ratio.

(Three phase series RLC Branch)

The Three-Phase Series RLC Branch block implements three balanced branches consisting each
of a resistor, an inductor, or a capacitor or a series combination of these. Use the Branch type
parameter to select elements you want to include in each branch.

Three phase Transformer (Two Windings)

This block implements a three-phase transformer using three single-phase transformers. For a
detailed description of the electrical model of a single-phase transformer, see the Linear
Transformer block.

When activated, the saturation characteristic is the same as the one described for the Saturable
Transformer block. If the fluxes are not specified, the initial values are automatically adjusted so
that the simulation starts in steady state.

Three phase V-I Measurement

The Three-Phase V-I Measurement block is used to measure instantaneous three-phase voltages
and currents in a circuit. When connected in series with three-phase elements, it returns the three
phase-to-ground or phase-to-phase peak voltages and currents.

The block can output the voltages and currents in per unit (pu) values or in volts and amperes.

If you choose to measure phase-to-ground voltages in per unit, the block converts the measured
voltages based on peak value of nominal phase-to-ground voltage
Three phase Series RLC load

The Three-Phase Series RLC Load block implements a three-phase balanced load as a series
combination of RLC elements. At the specified frequency, the load exhibits a constant
impedance. The active and reactive powers absorbed by the load are proportional to the square of
the applied voltage.

.
LAB TASK

Using Simpower system tool and implement the three phase system as shown in figure below

Circuit Diagram 1:
Circuit Diagram 2:

You might also like