Technical data sheet SMD230A

Damper actuator for adjusting

dampers in technical building
installations
• Air damper size up to approx. 3.2 m²
• Torque motor 16 Nm
• Nominal voltage AC 230 V
• Control Open/close, 3-point
• Running time motor 20 s

Technical data
Electrical data Nominal voltage AC 230 V
Nominal voltage frequency 50/60 Hz
Nominal voltage range AC 85...265 V
Power consumption in operation 4.5 W
Power consumption in rest position 1W
Power consumption for wire sizing 8 VA
Power consumption for wire sizing note Imax 4 A @ 5 ms
Connection supply / control Cable 1 m, 3 x 0.75 mm²
Parallel operation Yes (note the performance data)
Functional data Torque motor 16 Nm
Direction of motion motor selectable with switch 0 (ccw rotation) / 1 (cw
rotation)
Manual override with push-button, can be locked
Angle of rotation Max. 95°
Angle of rotation note can be limited on both sides with adjustable
mechanical end stops
Running time motor 20 s / 90°
Sound power level, motor 55 dB(A)
Mechanical interface Universal shaft clamp reversible 10...20 mm
Position indication Mechanically, pluggable
Safety Protection class IEC/EN II reinforced insulation
Protection class UL II reinforced insulation
Degree of protection IEC/EN IP54
Degree of protection NEMA/UL NEMA 2
Enclosure UL Enclosure Type 2
EMC CE according to 2014/30/EU
Low voltage directive CE according to 2014/35/EU
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
Certification UL cULus according to UL60730-1A, UL60730-2-
14 and CAN/CSA E60730-1:02
Mode of operation Type 1
Rated impulse voltage supply / control 4 kV
Control pollution degree 3
Ambient temperature -30...50°C
Storage temperature -40...80°C
Ambient humidity Max. 95% r.H., non-condensing
Servicing maintenance-free
Weight Weight 1.8 kg

www.belimo.com SMD230A • en-gb • 2019-06-04 • subject to changes 1

 Damper actuator, Open/close, 3-point, AC 230 V, 16 Nm
SMD230A

Safety notes
• The device must not be used outside the specified field of application, especially not

! in aircraft or in any other airborne means of transport.

• Outdoor application: only possible in case that no (sea)water, snow, ice, insolation
or aggressive gases interfere directly with the actuator and that is ensured that the
ambient conditions remain at any time within the thresholds according to the data
sheet.
• Caution: Power supply voltage!
• Only authorised specialists may carry out installation. All applicable legal or
institutional installation regulations must be complied during installation.
• The device may only be opened at the manufacturer’s site. It does not contain any
parts that can be replaced or repaired by the user.
• Cables must not be removed from the device.
• To calculate the torque required, the specifications supplied by the damper
manufacturers concerning the cross-section, the design, the installation site and the
ventilation conditions must be observed.
• The device contains electrical and electronic components and must not be disposed
of as household refuse. All locally valid regulations and requirements must be
observed.

Product features
Simple direct mounting Simple direct mounting on the damper spindle with an universal spindle clamp,
supplied with an anti-rotation device to prevent the actuator from rotating.
Manual override Manual override with push-button possible (the gear is disengaged for as long as the
button is pressed or remains locked).
Adjustable angle of rotation Adjustable angle of rotation with mechanical end stops.
High functional reliability The actuator is overload protected, requires no limit switches and automatically stops
when the end stop is reached.

Accessories

Description Type
Electrical accessories Auxiliary switch 1 x SPDT add-on S1A
Auxiliary switch 2 x SPDT add-on S2A
Auxiliary switch 2 x SPDT add-on, grau S2A/300 GR
Auxiliary switch 2 x SPDT add-on, grau S2A/500 GR
Feedback potentiometer 200 Ω add-on P200A
Feedback potentiometer 500 Ω add-on P500A
Feedback potentiometer 500 Ω add-on, grau P500A GR
Feedback potentiometer 1 kΩ add-on P1000A
Feedback potentiometer 2.8 kΩ add-on P2800A
Feedback potentiometer 2.8 kΩ add-on, grau P2800A GR
Feedback potentiometer 1 kΩ add-on, grau P1000A GR
Feedback potentiometer 5 kΩ add-on P5000A
Feedback potentiometer 5 kΩ add-on, grau P5000A GR
Feedback potentiometer 10 kΩ add-on P10000A
Feedback potentiometer 10 kΩ add-on, grau P10000A GR
Description Type
Mechanical accessories Actuator arm for standard shaft clamp (reversible) AH-20
Shaft extension 240 mm Ø20 mm for damper shaft Ø 12...21 mm CrNi AV12-25-I
Shaft extension 240 mm Ø20 mm for damper shaft Ø 8...22.7 mm AV8-25
Ball joint suitable for damper crank arm KH8<br/>for round iron rods KG8
with ∅ 8 mm
Ball joint suitable for damper crank arm KH8 / KH10<br/>for round iron KG10A
rods with ∅ 10 mm
Damper crank arm Slot width 8.2 mm, clamping range Ø10...18 mm KH8

2 SMD230A • en-gb • 2019-06-04 • subject to changes www.belimo.com

 Damper actuator, Open/close, 3-point, AC 230 V, 16 Nm
SMD230A

Accessories

Description Type
Shaft clamp one-sided, clamping range Ø8...26 mm, Multipack 20 pcs. K-ENSA
Shaft clamp one-sided, clamping range Ø12...26 mm, for CrNi shaft K-ENSA-I
(INOX), Multipack 20 pcs.
Shaft clamp reversible, clamping range Ø10...20 mm K-SA
Anti-rotation mechanism 180 mm, Multipack 20 pcs. Z-ARS180
Anti-rotation mechanism 230 mm, Multipack 20 pcs. Z-ARS230
Form fit insert 10x10 mm, Multipack 20 pcs. ZF10-NSA
Form fit insert 12x12 mm, Multipack 20 pcs. ZF12-NSA
Form fit insert 15x15 mm, Multipack 20 pcs. ZF15-NSA
Form fit insert 16x16 mm, Multipack 20 pcs. ZF16-NSA
Mounting and linkage kit for flat installation ZG-SMA
Position indicator, Multipack 20 pcs. Z-PI
Base plate extension for SM..A to SM../AM../SMD24R Multipack 20 Z-SMA
pcs.

Electrical installation

Notes • Caution: Power supply voltage!

! • Parallel connection of other actuators possible. Observe the performance data.

Wiring diagrams

AC 230 V, open-close AC 230 V, 3-point

N L N L

1 2 3 1 2 3
Cable colours: Cable colours:
0 1 = blue 0 1 = blue
0 2 = brown 0 2 = brown
1 1
1 3 = white 1 3 = white

www.belimo.com SMD230A • en-gb • 2019-06-04 • subject to changes 3

 Damper actuator, Open/close, 3-point, AC 230 V, 16 Nm
SMD230A

Dimensions [mm]
Spindle length Dimensional drawings

Min. 48 
L

64
Min. 20 

58
Clamping range
139

4
88

10 ... 20 mm ≥10 mm

30 131 41

≤20 mm

When using a round spindle made of CrNi

(INOX): Ø 12...20 mm

4 SMD230A • en-gb • 2019-06-04 • subject to changes www.belimo.com