3PE

Aluminium gear pumps

Technical Catalogue
E0.130.0219.02.00IM04
 GEAR PUMPS “E”- “B”- “C” SERIES
Aluminium Body General Features

GEAR PUMPS

SALAMI gear pumps are available with displacements from 1.4 cm3/rev to 99 cm3/rev (from 0.09 cu.in/rev to 6.03
cu.in/rev).
Multiple pumps can always be relized combining stages taken from different or same series.
Several options of shafts, flanges and ports as for European, German and American standards are available for all
the pumps.

SALAMI gear pumps offer:

•High volumetric efficiency thanks to an innovative design and an accurate control of machining tolerances.
•Axial compensation achieved by the use of floating bushes that allow high volumetric efficiency throughout the
working pressure range.
•DU bearings to ensure high pressure capability.
•12 teeth integral gear and shaft.
•Aluminium body.
•Cast iron flange and cover.
•Double shaft seals.
•Nitrile seals as standard and Viton seals in high temperature applications.
•All pumps are hydraulically tested after assembly to ensure the highest standard performance.
•Gear pumps are ideal for mobile equipment including: snow plows, light duty equipment, farm vehicles, town
trucks, cherry pickers, lift gates, utility vehicles, aerial devices, hoists, spreaders, fan drive.
•Also available Bidirectional rotation.

TECHNICAL DATA

0.8 to 1.5 bar

- Pump inlet pressure (absolute pressure)
(11.6 to 21.7 psi)
- Minimum operating fluid viscosity 12 mm2 / sec
- Max starting viscosity 800 mm2 / sec
- Suggested fluid viscosity range 17 - 65 mm2 / sec
- Fluid operating temperature range -20 to 80 °C
- Fluid operating temperature range with FPM seals (Viton) -15 to 110°C
- Fluid operating temperature range with HNBR seals* -30 to 110°C
E0.100.0219.02.00IM02

- Hydraulic fluid
GEAR PUMP mineral oil
“PG” SERIES on request.
*Available
End
Features
plate

DEFINITION OF PRESSURES
DEFINITION OF PRESSURES

P3 = Peak
P3 =pressure
Peak pressure
P2 = Intermittent
P2 = Intermittent operating
operating pressurepressure (1/3 of working
(1/3 of working time) time)
P1 = Continuous operating pressure
P1 = Continuous operating pressure

max. 20 s

GENERAL

Superior performance and reliability in

heavy-duty hydraulic application.
www.salami.it 5
Construction with large area, low-friction
bushings provide strength, high efficiency, and long life in severe operating environments.
 GEAR PUMPS “E”- “B”- “C” SERIES
General Features Aluminium Body

DRIVE SHAFTS

Radial and axial loads on the shafts must be avoided since they reduce the life of the unit.
In order to avoid misalignment during the assembly with the primary engine, a connection with “Oldham” coupling (or
coupling having convex toothed hub) is recommended.

ROTATION

Inlet Outlet Outlet Inlet

Clockwise rotation PUMP Anti - clockwise rotation PUMP

Reversible rotation PUMP

Pdrain < 3 bar

(43 psi)

VIEWED AT THE DRIVE SHAFT

HYDRAULIC PIPE LINE E0.100.0219.02.00IM02

To ensure favorable suction conditions it is important to keep pressure drop in suction pipe line to a minimum value
(see TECHNICAL DATA).
To calculate hydraulic pipe line size, the designer can use; as an approximate guide, the following fluid speed figures:

From 1 to 2 m/sec on suction pipe line From 3.28 to 6.36 ft/sec on suction pipe line
From 6 to 10 m/sec on pressure pipe line From 19.7 to 32.8 ft/sec on pressure pipe line

The lowest fluid speed values in pipe lines is recommended when the operating temperature range is high and/or for
continuos duty.
The highest value is recommended when the temperature difference is low and/or for intermittent duty.
When tandem pumps are supplied by 2 different reservoirs with 2 different fluids it is necessary to specify “AS”
version.

6 www.salami.it
 GEAR PUMPS “E”- “B”- “C” SERIES
Aluminium Body General Features

FILTRATION INDEX RECOMMENDED

Working pressure >200 bar/2900 psi <200 bar/2900 psi

Contamination class NAS 1638 9 10
Contamination class ISO 4406 19/18/15 20/19/16
Achieved with filter βx=75 15 µm 25 µm

FIRE RESISTENT FLUID

Type Description Max pressure Max speed (rpm) Temperature

HFB Oil emulsion with 40% water 130 bar/1880 psi 2500 3°C+65°C
HFC Water glycol 1500 -20°C+65°C
180 bar/2600 psi
HFD Phosphate esters 1750 -10°C+80°C

COMMON FORMULAS FOR PUMPS

IDENTIFICATION LABEL
E0.100.0219.02.00IM02

612027332 Salami product code

2/2019 Month and year of

Made in Italy production
Product short description 2PE11,3D-R55S3
001-W01 - - - - - - Nr 1 Progressive number
of assembling
Rot.

Rotation sense
Work order
(for Salami management)

www.salami.it 7
 GEAR PUMPS “E”- “B”- “C” SERIES
General Features Aluminium Body

WORKING CONDITIONS

Continuous Intermittent Peak Max. Min.

Displacement
pressure P1** pressure P2 pressure P3 speed speed
GROUP 1.5 - E SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
1.5PE - 1.4 1.4 0.09 250 3625 270 3915 290 4205 5000 700
1.5PE - 2.1 2.1 0.13 250 3625 270 3915 290 4205 5000 700
1.5PE - 2.8 2.8 0.17 250 3625 270 3915 290 4205 4500 700
1.5PE - 3.5 3.5 0.21 250 3625 270 3915 290 4205 4500 700
1.5PE - 4.1 4.1 0.25 250 3625 270 3915 290 4205 4000 700
1.5PE - 5.2 5.2 0.32 230 3335 250 3625 270 3915 4000 700
1.5PE - 6.2 6.2 0.38 230 3335 250 3625 270 3915 3600 600
1.5PE - 7.6 7.6 0.46 200 2900 220 3190 250 3625 3300 600
1.5PE - 9.3 9.3 0.57 180 2610 200 2900 240 3480 3000 600
1.5PE - 11 11 0.67 170 2465 190 2755 220 3190 3000 600

GROUP 2 - E SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
2PE - 3.2* 3.2 0.19 250 3625 280 4060 300 4350 4000 600
2PE - 3.9* 3.9 0.24 250 3625 280 4060 300 4350 4000 600
2PE - 4.5 4.6 0.27 250 3625 280 4060 300 4350 4000 600
2PE - 6.5 6.5 0.4 250 3625 280 4060 300 4350 4000 600
2PE - 8.3 8.2 0.5 250 3625 280 4060 300 4350 3500 500
2PE - 10.5 10.6 0.65 250 3625 280 4060 300 4350 3500 500
2PE - 11.3 11.5 0.68 250 3625 280 4060 300 4350 3500 500
2PE - 12.5 12.7 0.77 250 3625 280 4060 300 4350 3500 500
2PE - 13.8 13.8 0.84 250 3625 280 4060 300 4350 3500 500
2PE - 16 16.6 1.01 250 3625 280 4060 300 4350 3000 400
2PE - 19 19.4 1.15 220 3190 240 3480 260 3750 3000 400
2PE - 22.5 22.9 1.37 200 2900 220 3190 240 3480 2750 400
2PE - 26 25.8 1.58 180 2610 200 2900 220 3190 2500 400
*Available only as rear pump

GROUP 2.5 - B SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
2.5PB - 5.5* 5.97 0.36 250 3625 280 4060 300 4350 3000 600
E0.100.0219.02.00IM02
2.5PB - 8.3* 8.29 0.50 250 3625 280 4060 300 4350 3000 600
2.5PB - 11.5* 11.76 0.72 250 3625 280 4060 300 4350 3000 600
2.5PB - 13.8* 14.07 0.86 250 3625 280 4060 300 4350 3000 600
2.5PB - 16 16 0.97 250 3625 280 4060 300 4350 3000 600
2.5PB - 19 19.3 1.17 250 3625 280 4060 300 4350 3000 600
2.5PB - 22 22.2 1.35 250 3625 280 4060 300 4350 3000 500
2.5PB - 25 25.2 1.53 250 3625 280 4060 300 4350 3000 500
2.5PB - 28 27.6 1.68 250 3625 280 4060 300 4350 3000 500
2.5PB - 32 32.4 1.97 230 3335 250 3625 260 3750 3000 500
2.5PB - 38 38.1 2.32 200 2900 220 3190 240 3480 2750 400
2.5PB - 44 44.2 2.69 170 2465 190 2755 210 3040 2500 400
*Available only as rear pump. Displacements 11.5-13.8 are available as single pump only with drive shaft “55”.

8 www.salami.it
 GEAR PUMPS “E”- “B”- “C” SERIES
Aluminium Body General Features

WORKING CONDITIONS

Continuous Intermittent Peak Max. Min.

Displacement
pressure P1** pressure P2 pressure P3 speed speed
GROUP 3 - E SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
3PE - 21 20.6 1.26 250 3625 280 4060 300 4350 3000 600
3PE - 27 27 1.65 250 3625 280 4060 300 4350 3000 600
3PE - 33 33.5 2.04 250 3625 280 4060 300 4350 3000 600
3PE - 38 38.7 2.36 250 3625 280 4060 300 4350 2750 500
3PE - 46 46.9 2.86 250 3625 270 3915 280 4060 2750 500
3PE - 55 54.1 3.3 220 3190 240 3480 250 3625 2500 400
3PE - 65 63.1 3.85 200 2900 220 3190 240 3480 2500 400
3PE - 75 73.4 4.48 180 2610 200 2900 220 3190 2500 400

GROUP 3.5 - C SERIES cm3/rev cu.in/rev bar psi bar psi bar psi min-1
3.5PC - 55 54.8 3.34 250 3625 280 4060 300 4350 2750 400
3.5PC - 64 63.2 3.85 250 3625 280 4060 300 4350 2750 350
3.5PC - 75 74.7 4.55 230 3335 250 3625 280 4060 2500 300
3.5PC - 87 88 5.36 210 3040 230 3330 260 3750 2250 300
3.5PC - 98* 99 6.03 200 2900 220 3190 250 3625 2000 300
*Displacement 98 are special release, please contact sales department.

**For working conditions, using exclusively pressure P1, the value of max. speed must be reduced of 10%.

For bidirectional pump the max pressure has to be reduced of 10%.

The max pressure is refered to pumps with flanged ports, using the threaded ports the pump life could be reduced.
E0.100.0219.02.00IM02

www.salami.it 9
 GEAR PUMPS “E”- “B”- “C” SERIES
General Features Aluminium Body

ROTATION CHANGING INSTRUCTIONS FOR UNITS

Before starting, be sure that the pump is cleaned externally as well as the working area to avoid that particles
dangerous for pump working can find their way into the pump. Pump represented is a clockwise rotation pump.
To obtain an anti_clockwise rotation read carefully the following instructions.

CLOCKWISE ROTATION
Inlet Outlet

9 - Re-locate the driving

gear in the position
previously occupied by the
driven gear.
1 - Loosen and fully unscrew
the screws. 9
1
2 - Lay the pump on the
working area in order to
have the mounting flange
turned upside.
10 - Replace the bushing
and thrust plate taking care
3 - Coat the shaft extension
that:
with grease to avoid
- marks are located as on
damaging the shaft seal. 10 the picture
- surface containing the
4 - Remove the flange and
seal is visible
lay it on the working area;
- seal and its protection are
verify that the seal is
4 correctly located in the body
correctly located.
seat.

11 - Clean body and

mounting flange refaced
surfaces.

12 - Verify that the two

5 5 - Mark the position of the plugs are located in the
bushing and eventually the thrust body.
plate, relative to the body. 14
13 - Refit the mounting
E0.100.0219.02.00IM02
6 - Remove the bushing, thrust flange, turned 180° from its
plate and the driving gear taking original position.
6 care to avoid driven gear axial
shifts. 14 - Replace the clamp
bolts and tighten crosswise
evenly to an appropriate
torque.

15 - Check that the shaft

7 - Draw out the driven gear from rotates freely.
its housing, taking care to avoid
rear cover axial shifts. 16 - Mark on the flange the
new direction of rotation.
8
8 - Re-locate the driven gear in
the position previously occupied
7 by the driving gear.
ANTI - CLOCKWISE ROTATION
Outlet Inlet

10 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

INDEX

Shafts And Flanges Combination...............................................................91

Assembling Dimensions And Working Conditions.....................................92
Flanged And Threaded Ports......................................................................94
Drive Shafts................................................................................................96
Mounting Flanges.......................................................................................97
Outrigger Bearing.......................................................................................98
Rear Cover...............................................................................................100
Priority Valves...........................................................................................101
Multiple Gear Pumps Assembling Dimensions.........................................103
3PE Combination With Pump 2PE...........................................................104
3PE Combination With Pump 1.5PE........................................................104
Performance Curves................................................................................105
How To Order Single Pumps....................................................................109
How To Order Multiple Pumps..................................................................110

Final revised edition - February 2019

The data in this catalogue refers to the standard product.
The policy of Salami S.p.A. consists of a continuous improvement of its products. It reserves the right to change the
specifications of the different products whenever necessary and without giving prior information.
If any doubts, please contact our sales department.

www.salami.it 89
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

SHAFTS AND FLANGES COMBINATION

3PE
E0.130.0219.02.00IM04

www.salami.it 91
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

Displacements up to 4.48 cu.in./rev GEAR PUMPS Displacements up to 73.4 cm3/rev

Pressure up to 4350 psi Pressure up to 300 bar

ASSEMBLING DIMENSIONS AND

WORKING CONDITIONS

Type 21 27 33 38 46 55 65 75

cm3/rev 20.6 27 33.5 38.7 46.9 54.1 63.1 73.4

Displacement
cu.in./rev 1.26 1.65 2.04 2.36 2.86 3.3 3.85 4.48
mm 74 79 84 88 104 110 117 124
Dimension A
in 2.91 3.11 3.31 3.46 4.09 4.33 4.61 4.88
mm 37 39.5 42 44 52 55 58.5 62
Dimension C
in 1.46 1.56 1.65 1.73 2.05 2.17 2.30 2.44
Continuous bar 250 250 250 250 250 220 200 180
P1
pressure psi 3625 3625 3625 3625 3625 3190 2900 2610
Intermittent bar 280 280 280 280 270 240 220 200
P2
pressure psi 4060 4060 4060 4060 3915 3480 3140 2900
Peak bar 300 300 300 300 280 250 240 220
P3
pressure psi 4350 4350 4350 4350 4060 3625 3480 3140

Max speed rpm 3000 3000 3000 2750 2750 2500 2500 2500

Min speed rpm 600 600 600 500 500 400 400 400

kg 8.80 9.10 9.46 9.60 10.40 10.80 11.00 11.50

Weight
lbs 19.40 20.06 20.86 21.16 22.93 23.81 24.25 25.35

95-105 Nm
22 32.5 (70-77.4 lbf∙ft)
.87 A 1.28
5 19
.20 C

E0.130.0219.02.00IM04
.87
22

Body width
Ø 2.000

Showed release with

Ø 50.8

flange P2 and shaft 38

92 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

Displacements up to 4.48 cu.in./rev GEAR PUMPS Displacements up to 73.4 cm3/rev

Pressure up to 4350 psi Pressure up to 300 bar

ASSEMBLING DIMENSIONS

Type 46 55 65 75

cm3/rev 46.9 54.1 63.1 73.4

Displacement
cu.in./rev 2.86 3.3 3.85 4.48
mm 104 110 117 124
Dimension A
in 4.09 4.33 4.61 4.88
mm 52 55 58.5 62
Dimension C
in 2.05 2.17 2.30 2.44
kg 10.1 10.5 10.8 11.2
Weight
lbs 22.3 23 23.8 24.6

95-105 Nm
22 32.5 (70-77.4 lbf∙ft)
.87 A 1.28 136.2
5.36
5 19
.20 C 114.2
4.50

60.3
2.37
49.3
1.94
.87
22

149.3
5.88

4.37
111
Tapered 1:8
E0.130.0219.02.00IM04

O 11
.43

Showed release with

flange P3 and shaft 48.
Interchangeable with 3.5PC

www.salami.it 93
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

FLANGED AND THREADED PORTS

TYPE INLET OUTLET

UNI-DIRECTIONAL ØD ØA d e ØD ØA d e
PUMPS
From 21 27 51 16 40
M10 M8
to 55 (1.06”) (2.01”) (0.63”) (1.57”)
16 16
(0.63”) (0.63”)
From 65 33 62 21 51
M12 M10
to 75 (1.3”) (2.44”) (0.83”) (2.01”)
code P
BI-DIRECTIONAL PUMPS Special version available on request.
Flanged ports
european standard

TYPE INLET OUTLET

UNI-DIRECTIONAL ØD ØA d e ØD ØA d e
PUMPS
22
21
(0.86”)
55 13 19 55 13
M8 M8
(2.17”) (0.51”) (0.75”) (2.17”) (0.51”)
From 27 27
code B to 75 (1.06”)

Flanged ports BI-DIRECTIONAL PUMPS Special version available on request.

german standard

E0.130.0219.02.00IM04

TYPE INLET OUTLET

UNI-DIRECTIONAL
PUMPS ØD B A d e ØD B A d e

From 21 26 52.4 26.2 19 47.6 22.2

to 38 (1.02”) (2.06”) (1.03”) (0.75”) (1.87”) (0.87”)
18 18
M10 M10
(0.71”) (0.71”)
From 46 32 58.7 30.2 26 52.4 26.2
code W to 75 (1.26”) (2.31”) (1.19”) (1.02”) (2.06”) (1.03”)

Flanged ports BI-DIRECTIONAL PUMPS Special version available on request.

SAE J518
METRIC THREAD

94 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

TYPE INLET OUTLET

UNI-DIRECTIONAL
PUMPS ØD B A d e ØD B A d e

From 26 52.4 26.2 3/8 19 47.6 22.2

21 to 38 (1.02”) (2.06”) (1.03”) 16 UNC (0.75”) (1.87”) (0.87”)
18 3/8 18
(0.71”) 16 UNC (0.71”)
From 32 58.7 30.2 7/16 26 52.4 26.2
46 to 75 (1.26”) (2.31”) (1.19”) 14 UNC (1.02”) (2.06”) (1.03”)
code S
BI-DIRECTIONAL PUMPS Special version available on request.
Flanged ports
SAE J518
AMERICAN STANDARD
THREAD

TYPE INLET OUTLET

UNI-DIRECTIONAL
A B C A B C
PUMPS
From 22 27
G1
21 to 38 (0.86”) (1.06”)
22 27
G1
From 24 32.5 (0.86”) (1.06”)
G1 1/4
46 to 75 (0.94”) (1.28”)

code G BI-DIRECTIONAL PUMPS Special version available on request.

Threaded ports
GAS (BSPP)
E0.130.0219.02.00IM04

TYPE INLET OUTLET

UNI-DIRECTIONAL
PUMPS A B C Y K A B C Y K

1-5/16-12 1-1/16-12
From 25 49 21 41
UN UN
21 to 38 (0.98”) (1.93”) (0.83”) (1.16”)
(SAE 16) (SAE 12)
19 3.3 19 3.3
1-5/8-12 (0.75”) (0.12”) 1-5/16-12 (0.75”) (0.13”)
From 27 58 25 49
UN UN
46 to 75 (1.06”) (2.28”) (0.98”) (1.93”)
(SAE 20) (SAE 16)
code R
BI-DIRECTIONAL PUMPS Special version available on request.
Threaded ports
SAE (ODT)

www.salami.it 95
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

DRIVE SHAFTS
Woodruff key
Woodruff key
(3.958x7.5)
(5x7.5)

Mounting face Mounting face

Mounting face

code 05 Max torque 180 Nm (1590 lbf in) code 35 Max torque 260 Nm (2300 lbf in) code 38 Max torque 250 Nm (2213 lbf in)

Tang drive for electric motor European tapered 1:5 European tapered 1:8

[0.984]
Ø25

Mounting face Mounting face Mounting face

code 48 Max torque 350 Nm (3100 lbf in) code 55 Max torque 330 Nm (2921 lbf in) code 56 Max torque 480 Nm (4250 lbf in)

European tapered 1:8 for 3.5PC SAE B 13T-16/32DP Ansi B92 1a 1976 SAE BB 15T-16/32DP Ansi B92 1a 1976

E0.130.0219.02.00IM04

Mounting face

Mounting face

code 65 Max torque 280 Nm (2478 lbf in) code 87 Max torque 220 Nm (1950 lbf in) code 88 Max torque 320 Nm (2830 lbf in)

DIN 5480 internal splined (only for rear SAE B Parallel SAE BB Parallel
pumps)

96 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

MOUNTING FLANGES

S3 SAE B 2 Bolts P2 European standard

With shaft code 55-56-87-88 With shaft code 38
E0.130.0219.02.00IM04

P3 European standard for 3.5PC B6 German standard

With shaft code 48 With shaft code 05-35

www.salami.it 97
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

OUTRIGGER BEARING

The following diagrams show radial load capability

of the bearing.
Calculation according to ISO 281 at 10 cSt.

TYPE H Fr
27 79 (3.11”)
33 84 (3.31”)
38 88 (3.46”) L=Distance between
46 104 (4.09”) mounting flange and
55 110 (4.33”)
radial force point of
65 117 (4.61”)
application.

Example:
Fr = 3000 N
Expected life: 1000 hrs
L = 35
Speed = 2500 rpm

For Code CP

E0.130.0219.02.00IM04
For Code CSB

98 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

MOUNTING FLANGES WITH BEARING

CP European standard Ø50.8 mm

With shaft code 38

E0.130.0219.02.00IM04

CSB SAE B

With shaft code 55-56-87-88

www.salami.it 99
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

REAR COVER

external drain
DIMENSION C
Standard rear cover Standard rear cover
for unidirectional pumps for reversible pumps, with external drain C.
For the dimension C please see the table here below

C
G3/8
9/16-18 UNF-2B (SAE6)

E0.130.0219.02.00IM04

Outlet Inlet
DIMENSION B DIMENSION A

code 1
For pumps with threaded rear ports, suitable up to 80 l/min delivery.
A B
G1 G3/4
1-5/16-12 UN-2B 1-1/16-12 UN-2B
(SAE16) (SAE12)

100 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

PRIORITY VALVES

6°

Inlet

EF - Exceeded flow outlet

CF - Priority flow outlet

LS - Signal inlet

The double or triple pumps can be configurated with priority flow valve too.
The stage which has its flow divided into priority and exceeded flows is always the back one.

EF CF

code VP1 code VPD1

Priority flow valve, excess flow Load sensing priority valve
to second actuator. with dynamic signal without
main relief valve.
E0.130.0219.02.00IM04

EF CF

code VPS1 code VPDS1

Priority flow valve, excess flow Load sensing priority valve
to second actuator with dinamic signal with main
with pressure relief valve on relief valve.
priority flow line.

www.salami.it 101
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

VP1 - VPS1
SIDE PORTS
AXIS OF PUMP SHAFT
68.5 48 ANTI-CLOCKWISE ROTATION
2.70 1.89
59,9
2,4

2,5
64
59,9

CALIBRATED ORIFICE FLOW RATE

2,4

Φ d (mm/inch) (l/min - gpm) ± 10%

1.5 /(0.06”) 2.5 - (0.66)
2 /(0.08”) 4 - (1.06)
AXIS OF PUMP SHAFT 64 2.4 /(0.09”) 6 - (1.59)
CLOCKWISE ROTATION
2,5 2.8 /(0.11”) 8 - (2.11)
3.1 /(0.12”) 10 - (2.64)
VPD1 - VPDS1 3.5 /(0.14”) 12.5 - (3.30)
A D
SIDE PORTS 4 /(0.16”) 16 - (4.23)
G 3/8 G 3/4
4.4 /(0.17”) 20 - (5.28)
SAE8 SAE12
3/4-16 UNF-2B 1 1/16 - 12 UN - 2B 4.9 /(0.19”) 25 - (6.61)

AXIS OF PUMP SHAFT

ANTI-CLOCKWISE ROTATION
68.5 48
2.70 1.89
59,9

E0.130.0219.02.00IM04
2,4

2,5
64

Female fitting Male fitting

59,9
2,4

AXIS OF PUMP SHAFT

CLOCKWISE ROTATION

64
2,5

A D E
G 3/8 G 3/4 G 1/4
SAE8 SAE12 SAE4
3/4 - 16 UNF - 2B 1-1/16 - 12 UN - 2B 7/16 - 20 UNF - 2B

102 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

MULTIPLE GEAR PUMPS

ASSEMBLING DIMENSIONS

MULTIPLE MULTIPLE
GEAR PUMPS GEAR PUMPS
with inlet port with common
on each body inlet port*
*In case of common inlet port, to avoid too
high value of oil speed, 60 l/min is the max
sucked flow for the downstream pump.
Commercial code UA.

Type 21* 27 33 38 46 55 65 75*

cm3/rev 20.6 27 33.5 38.7 46.9 54.1 63.1 73.4

Displacement
cu.in./rev 1.26 1.65 2.04 2.36 2.86 3.3 3.85 4.48
mm 74 79 84 88 104 110 117 124
Dimension A
in 2.91 3.11 3.31 3.46 4.09 4.33 4.61 4.88
mm 37 39.5 42 44 52 55 58.5 62
Dimension C
in 1.46 1.56 1.65 1.73 2.05 2.17 2.30 2.44

*Displacements 21 and 75 are special release, please contact sales department.

22 9.6 32.5 95-105 Nm

.87 A .38 A 1.28 173.8
(70-77.4 lbf∙ft) 6.84
9.5 73 73
.37 C C 19 2.87 2.87

59.9
2.36
.87
22

Max. torque
3.62
280 Nm 92
(2921 lbf in)
E0.130.0219.02.00IM04

14.5
n.2 holes O .57
Front pump Rear pump

This is a Salami standard pump, These units are pre-arranged for multiple
alla drive shafts have a splined end. pumps, they have the drive shaft code 65.

www.salami.it 103
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

3PE COMBINATION WITH PUMP 2PE

Kit multiple pumps ALL THE PUMPS
PD2 Pre-arranged for 2PE rear CAN BE ALSO
MULTIPLE

MULTIPLE
GEAR PUMPS
with inlet port
on each body 19

MULTIPLE
GEAR PUMPS 17

with common
inlet port*
*In case of common inlet port, to avoid too high
value of oil speed, 30 l/min is the max. sucked flow
for the downstream pump.
Commercial code UA.

MULTIPLE
GEAR PUMPS
with separated
stages

code AS

2PE-Type 3.2* 3.9* 4.5 6.5 8.3 10.5 11.3 12.5 13.8 16 19 22.5 26

mm 47.1 49.95 52.8 56.3 59.7 63.5 67.5 75.6 81 86.8

Dimension A - 2PE
in 1.83 1.97 2.07 2.22 2.35 2.5 2.65 2.97 3.19 3.42
mm 23.55 25 26.4 28.15 29.75 31.75 33.75 37.80 40.5 43.4
Dimension C - 2PE
in 0.93 0.98 1.04 1.11 1.17 1.25 1.33 1.49 1.59 1.71
*Available only as rear pump

3PE COMBINATION WITH PUMP 1.5PE

Kit multiple pumps ALL THE PUMPS
PD1.5 Pre-arranged for 1.5PE rear CAN BE ALSO
MULTIPLE

MULTIPLE
GEAR PUMPS 19

with inlet port

on each body
13
E0.130.0219.02.00IM04
MULTIPLE
GEAR PUMPS
with common
inlet port*
*In case of common inlet port, to avoid too high
value of oil speed, 12 l/min is the max. sucked flow
for the downstream pump.
Commercial code UA.

1.5PE-Type 1.4 2.1 2.8 3.5 4.1 5.2 6.2 7.6 9.3 11

mm 44 45.9 47.9 49.9 51.6 54.7 57.5 61.5 66.3 71.1

Dimension A - 1.5PE
in 1.73 1.81 1.89 1.96 2.03 2.15 2.26 2.42 2.61 2.80
mm 22 22.95 23.95 24.95 25.8 27.35 28.75 30.75 33.15 35.55
Dimension C - 1.5PE
in 0.87 0.90 0.94 0.98 1.02 1.08 1.13 1.21 1.31 1.40

104 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C

40.00
70.00

Power
35.00
Flow rate [l/min] 20 bar [kW] 50
Flow rate [l/min] 300 bar bar

r
ba
Power
60.00 [kW] 100

0
ba

30
bar
Power

20
[kW] 150
bar
30.00

r
ba

r
ba
0
25
50.00

0
25
25.00

r
ba

Input power [kW]

40.00 0
20
Flow rate [l/min]

20.00

ar
30.00 0b
15
15.00

bar
20.00 100
10.00

r
50 ba
10.00
5.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 3500
0 800 1600 2400 3200
RPM RPM

3PE-21

90.00 Powe
Powe
Powe
Powe
80.00
Powe
r
ba

Powe
20

50.00 Flow rate

[l/min] 20 bar
70.00
r
ba

Flow rate r
ba
0

45.00 [l/min] 300 bar

25

0
30
E0.130.0219.02.00IM04

60.00
40.00
r
ba
0
25
35.00
Flow rate [l/min]

50.00

ar
30.00 0b
20
Input power [kW]

40.00

25.00
ar
0b
15
30.00
20.00

bar
15.00 100
20.00

10.00
r
50 ba
10.00
5.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 3500 0 800 1600 2400 3200
RPM RPM

3PE-27

www.salami.it 105
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C

60.00
120.00

r
ba
0
30
Flow rate [l/min] 20 bar

Flow rate [l/min] 300 bar

50.00
100.00
r

r
ba

ba
0
20
25

r
ba 40.00
0
25
80.00
r
ba
0
20

Input power [kW]

Flow rate [l/min]

Power [kW] 50 b

Power [kW] 100

60.00 30.00 r
0 ba Power [kW] 150
15
Power [kW] 200

Power [kW] 250

Power [kW] 300

40.00 20.00 bar
100

r
20.00 10.00 50 ba

0.00
0.00
0 500 1000 1500 2000 2500 3000 3500
0 400 800 1200 1600 2000 2400 2800 3200
RPM
RPM

3PE-33

60.00
120.00

r
ba
0
28

Flow rate [l/min] 20 bar

50.00 Power [kW]
bar
r
Flow rate [l/min] 280 bar
ba

100.00 Power [kW]

r
ba

bar
20

25

Power [kW]
bar
Power [kW]
r

bar
ba
0

r
24

40.00 ba E0.130.0219.02.00IM04
80.00 0
20
Input power [kW]
Flow rate [l/min]

30.00 ar
60.00 0b
15

20.00 bar
40.00 100

r
10.00 50 ba
20.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM

3PE-38

106 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE

PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C

140.00 70.00

r
ba
0
28
Flow rate [l/min] 20 bar
120.00 60.00

r
ba

ba
Flow rate [l/min] 280 bar

20

0
25
r
ba
0
25
P
100.00 50.00
e
r
ba [k
0 5
20 b

Input power [kW]

40.00
Flow rate [l/min]

80.00
ar
0b
15

60.00 30.00

bar
100
40.00 20.00

r
50 ba
20.00 10.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM

3PE-46

140.00 70.00
Power [kW] 40 bar
Power [kW] 80 bar
r
ba

Power [kW] 120 bar

20

ar

Power [kW] 160 bar

0b

120.00
r

60.00
ba

25

Power [kW] 200 bar

0
22

Power [kW] 250 bar

Flow rate [l/min] 20 bar
r
ba

Flow rate [l/min] 250 bar

100.00
0

50.00
20
E0.130.0219.02.00IM04

r
ba
0
16
Flow rate [l/min]

80.00 40.00
Input power [kW]

r
ba
60.00 30.00 0
12

r
ba
40.00 20.00 80

r
40 ba
20.00 10.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM
RPM

3PE-55

www.salami.it 107
 GEAR PUMPS “E” SERIES
3PE Aluminium Body

PERFORMANCE CURVES
Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C
80.00

160.00
Flow rate Power [kW] 40

r
[l/min] 20 bar bar

ba

r
70.00

ba
Power [kW] 80

20

0
bar

24
140.00 Power [kW] 120

ar
0b
bar

20
60.00

r
ba
120.00

0
20
50.00
r
100.00 ba
0
16

Input power [kW]

Flow rate [l/min]

40.00
80.00
ar
0b
12

30.00
60.00

bar
80
20.00
40.00

r
40 ba
20.00 10.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM

3PE-65
80.00

180.00
ar
0b
22
r
ba

70.00
ar
20

0b

160.00
18

r
ba

140.00 60.00
5
17

120.00 E0.130.0219.02.00IM04
50.00 r
ba
0
Flow rate [l/min] 20 bar 12
Input power [kW]
Flow rate [l/min]

100.00 Flow rate [l/min] 220 bar

40.00
ar
5b
80.00 10

30.00

60.00 bar
70

20.00
40.00
r
35 ba
10.00
20.00

0.00 0.00
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
RPM RPM

3PE-75

108 www.salami.it
 GEAR PUMPS “E” SERIES
Aluminium Body 3PE-How to order

SINGLE PUMPS
Adjustable flow l/min

A B C D E F G H I L
3PE - - ... / ...
Setting main
relief valve (bar)

DISPLACEMENTS A CODES L VALVES IN THE COVER (page 101) CODES

20.6 cm3/rev. 1.26 cu.in/rev. 21 Priority flow divider with excess flow to
VP1
2nd actuator
27 cm3/rev. 1.65 cu.in/rev. 27
Like VP with main relief valve VPS1
33.5 cm3/rev. 2.04 cu.in/rev. 33
Priority flow divider with Load sensing
VPD1
38.7 cm3/rev. 2.36 cu.in/rev. 38 with dinamic signal
46.9 cm3/rev. 2.86 cu.in/rev. 46 Load sensing priority valve with dinamic
VPDS1
signal with main relief valve
54.1 cm /rev.
3
3.3 cu.in/rev. 55
63.1 cm3/rev. 3.85 cu.in/rev. 65 I REAR COVER (page 104) CODE

73.4 cm /rev.
3
4.48 cu.in/rev. 75 Pre-arranged for 1.5PE rear PD1.5
Pre-arranged for 2PE rear PD2
ROTATION (page 6) CODES B
Clockwise D H OUTRIGGER BEARING (page 98) CODES
Anti-clockwise S European standard CP
Reversible R German standard CSB

PORTS (page 94) CODES C G PORTS POSITION CODE

Flanged ports Lateral ports standard
P
european standard
Rear ports (page) 1
Flanged ports
B
german standard
Threaded ports
F SEAL CODE
G Buna standard
GAS (BSPP)
Threaded ports Viton V
R
SAE (ODT)
Flanged ports E MOUNTING FLANGES (page 97) CODES
SAE J518 AMERICAN S
SAE B 2 Bolts S3
STANDARD THREAD
Flanged ports European standard Ø50.8 P2
W
SAE J518 METRIC THREAD European standard Ø60.3 P3

DRIVE SHAFT (page 96) CODES D German standard Ø105 B6

Tang drive for electric motor 05

E0.130.0219.02.00IM04

European Tapered 1:5 35

European Tapered 1:8 38
European Tapered 1:8 48
SAE B splined 13T 55
SAE BB splined 15T 56
DIN 5480 internal splined
(only for rear pumps- 65
see page 103)
SAE B parallel 87
SAE BB parallel 88
Order example: 3PE 46D, ports SAE (R), drive shaft (56),
mounting flange (S3)
3PE46D-R56S3

www.salami.it 109
 GEAR PUMPS “E” SERIES
How to order-3PE Aluminium Body

MULTIPLE PUMPS
Adjustable flow l/min

A B C D E F G H I L M
3PE / ...
Setting main
relief valve (bar)

DISPLACEMENTS A CODES M VALVES IN THE COVER (page 101) CODES

20.6 cm /rev.
3
1.26 cu.in/rev. 21 Priority flow divider with excess flow to
VP1
2nd actuator
27 cm3/rev. 1.65 cu.in/rev. 27
Like VP with main relief valve VPS1
33.5 cm3/rev. 2.04 cu.in/rev. 33
Priority flow divider with Load sensing
VPD1
38.7 cm3/rev. 2.36 cu.in/rev. 38 with dinamic signal
46.9 cm3/rev. 2.86 cu.in/rev. 46 Load sensing priority valve with dinamic
VPDS1
signal with main relief valve
54.1 cm3/rev. 3.3 cu.in/rev. 55
63.1 cm3/rev. 3.85 cu.in/rev. 65 L REAR COVER (page 104) CODE

73.4 cm3/rev. 4.48 cu.in/rev. 75 Pre-arranged for 1.5PE rear PD1.5

Pre-arranged for 2PE rear PD2
ROTATION (page 6) CODES B
Clockwise D I OUTRIGGER BEARING (page 98) CODES
Anti-clockwise S European standard CP
German standard CSB
PORTS (page 94) CODES C
Flanged ports
european standard
P H PORTS POSITION CODE
Lateral ports standard
Flanged ports
B
german standard Rear ports (page) 1
Threaded ports
G
GAS (BSPP)
Threaded ports
G SUCTION PORTS CODES
R
SAE (ODT) Common suction UA*
Flanged ports Separeted stages AS
SAE J518 AMERICAN S
STANDARD THREAD
F SEAL CODE
Flanged ports
W Buna standard
SAE J518 METRIC THREAD
Viton V
DRIVE SHAFT (page 96) CODES D
Tang drive for electric motor 05 E MOUNTING FLANGES (page 97) CODES

European Tapered 1:5 35 SAE B 2 Bolts S3

European Tapered 1:8 38 European standard Ø50.8 P2 E0.130.0219.02.00IM04
European Tapered 1:8 48 European standard Ø60.3 P3
SAE B splined 13T 55 German standard Ø105 B6
SAE BB splined 15T 56 *UA: this type of multiple pump is a Salami standard multiple
pump which has only one inlet port opened, all the other inlet
SAE B parallel 87
port are closed.
SAE BB parallel 88 In case of common suction, the code 1 - 2 or 3, correspond to
the body where inlet is located.
Order example: 3PE 33/27D, ports SAE (P), drive shaft (56),
mounting flange (S3)
3PE33/27D-R56S3

110 www.salami.it
www.salami.it
You can find our most up to date “STANDARD SALES CONDITIONS” on our website.
Potete trovare le nostre più aggiornate “CONDIZIONI DI VENDITA STANDARD” sul nostro sito.

Ph. +39 059 387 411 - [email protected]

Watch our tutorials on our official youtube channels:

Salami Fluid Power

Salami Fluid Power World
Salami Fluid Power France
Salami Fluid Power España
Salami Fluid Power Deutsch
SALAMI S.P.A. SALAMI FRANCE
Via Emilia Ovest 1006 22, rue Louis Saillant
69120 Valux en Velin
41121 Modena (Italy)
Lyon
Ph. +39 059 387 411 Ph. +33-04-78809941
F. +39 059 387 639 F. +33-04-78803669
[email protected] [email protected]

SALAMI ESPAÑA SALAMI HYDRAULICS N.A INC

Poligono Industrial Armenteres 4630 Crossroads Park Drive
C/Primer de Maig, 18, Nave 4 Liverpool
08980 San Feliu de Llobregat NY 13088 - USA
Barcelona Ph. +1-315-295-2363
Ph. +34-93-6665451 F. +1-315-295-2364
F. +34-93-6667826 [email protected]
[email protected]

www.salami.it