Scribd
Upload
53 views

CCNA Question and Answers 26-36

The document contains answers to questions about networking concepts. It defines different types of cables used for routing including straight, cross, and rollover cables. It explains the difference between static and dynamic IP addresses, with static addresses remaining fixed and dynamic addresses changing each time a device connects. It also defines peer-to-peer networks as decentralized networks where nodes act as both suppliers and consumers of resources.

Uploaded by

siraj noori
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
53 views

CCNA Question and Answers 26-36

The document contains answers to questions about networking concepts. It defines different types of cables used for routing including straight, cross, and rollover cables. It explains the difference between static and dynamic IP addresses, with static addresses remaining fixed and dynamic addresses changing each time a device connects. It also defines peer-to-peer networks as decentralized networks where nodes act as both suppliers and consumers of resources.

Uploaded by

siraj noori
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

Q #26) What are the different types of cables that are used in routing?

Answer: Three different types of cables that are used include:

Straight cable(switch-router)
Cross cable(PC-PC, switch-switch)
Rollover cable(Console port to computer)
Q #27) Define Logical Topology.

Answer: Logical Topology is the network from where the data packets are sent from
the source to destination, which we can see as well.

Q #28) What is the difference between static and dynamic IP addresses?

Answer: Static IP address will not change over time and is reserved statically
whereas dynamic IP address changes each time when you connect to the Internet.

Q #29) What is Peer to Peer network?

Answer: The P2P network is a distributed and decentralized network where individual
nodes i.e. Peers in the networks act as both suppliers and consumers of the
resources.

Q #30) What is the IEEE standard for wireless networking?

Answer: IEEE 802.11

Q #31) What do you understand by ‘Protocol’ in networking?

Answer: A protocol enables two devices to connect and transmit the information or
data to one another.

Q #32) What do you understand by PoE (Power over Ethernet)?

Answer: It is defined by the IEEE standard and it passes electric power supply to
the network devices over the existing data connection.

Q #33) What is OSPF? Describe it.

Answer: OSPF stands for Open Shortest Path First. It uses the Dijkstra algorithm
and is a link-state routing protocol that is used to connect to a large number of
networks without having any limitation on the number of hops.

Q #34) What does Multiple Access mean?

Answer: In Multiple Access, it allows more than one device to transmit the data at
the same time.

For Example, Star or Mesh Topology.

Q #35) Explain the difference between Collision Domain and Broadcast Domain.

Answer:

Broadcast Domain

In the Broadcast Domain, all the juncture can reach each other by broadcast at the
Data Link Layer and every device is ready to receive their respective data. It can
bind to the same LAN segments or the other LAN segment.
Broadcast Domain uses a local network for broadcasting the data packets to the
receiver. While broadcasting, massive data are broadcasted, hence the speed of
receiving the data is less and it also takes more time to receive the data of their
address.

Collision Domain

In the Collision Domain, data collision occurs more due to the sending of more
frames simultaneously.

If more than two frames are sent simultaneously then the data will collide with
each other in between and the information gets lost. Hence, the devices will not
accept the data and due to this, the communication between the sender and receiver
side will collide.

Thus, the sender has to send the data again and like this, it will take more time
to receive the data at the receiver's side.

Q #36) Frame Relay Technology works on which layer of the OSI model?

Answer: It works on the Data Link Layer.

You might also like