SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

D Complete PWM Power Control Circuitry D, DB, N, NS, PW, OR J PACKAGE

(TOP VIEW)
D Completely Synchronized Operation
D Internal Undervoltage Lockout Protection
REF
CT 1 16
D Wide Supply Voltage Range RT 2 15 SCP
D Internal Short-Circuit Protection ERROR 1IN+ 3 14 2IN+ ERROR
D Oscillator Frequency . . . 500 kHz Max AMPLIFIER 1 1IN– 4 13 2IN– AMPLIFIER 2
2FEEDBACK
D Variable Dead Time Provides Control Over 1FEEDBACK 5 12
1DTC 6 11 2DTC
Total Range
1OUT 7 10 2OUT
D Internal Regulator Provides a Stable 2.5-V GND 8 9 VCC
Reference Supply
D Available in Q-Temp Automotive
FK PACKAGE
HighRel Automotive Applications
(TOP VIEW)
Configuration Control / Print Support

SCP
REF
Qualification to Automotive Standards

NC
CT
RT
description 3 2 1 20 19
1IN+ 4 18 2IN+
The TL1451A incorporates on a single monolithic
chip all the functions required in the construction 1IN– 5 17 2IN–
of two pulse-width-modulation (PWM) control NC 6 16 NC
circuits. Designed primarily for power-supply 1FEEDBACK 7 15 2FEEDBACK
control, the TL1451A contains an on-chip 2.5-V
IDTC 8 14 2DTC
regulator, two error amplifiers, an adjustable
9 10 11 12 13
oscillator, two dead-time comparators, undervol-

V CC
GND
1OUT

NC

2OUT
tage lockout circuitry, and dual common-emitter
output transistor circuits.
The uncommitted output transistors provide
common-emitter output capability for each
controller. The internal amplifiers exhibit a common-mode voltage range from 1.04 V to 1.45 V. The dead-time
control (DTC) comparator has no offset unless externally altered and can provide 0% to 100% dead time. The
on-chip oscillator can be operated by terminating RT and CT. During low VCC conditions, the undervoltage
lockout control circuit feature locks the outputs off until the internal circuitry is operational.
The TL1451AC is characterized for operation from –20°C to 85°C. The TL1451AQ is characterized for operation
from –40°C to 125°C. The TL1451AM is characterized for operation from –55°C to 125°C.

AVAILABLE OPTIONS
PACKAGED DEVICES

TA SMALL SMALL SMALL CHIP CERAMIC

PLASTIC DIP TSSOP
OUTLINE OUTLINE OUTLINE CARRIER DIP
(N) (PW)†
(D) (DB)† (NS) (FK) (J)
–20°C to 85°C TL1451ACD TL1451ACDB TL1451ACN TL1451ACNS TL1451ACPW — —
–40°C to 125°C TL1451AQD — — — — — —
–55°C to 125°C — — — — — TL1451AMFK TL1451AMJ
† The DB and PW packages are only available left-end taped and reeled (add LE suffix, i.e., TL1451ACPWLE).

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.


 
   !"   #!$%  &"' Copyright  1999, Texas Instruments Incorporated

&!    #"   #" (" " 
") !"  #&!  #%  
- ./.0 %% #"" " ""&
&& *+'
&!  # ", &"  " "%+  %!&" !%" ("*" "&'  %% (" #&! 0 #&! 
",  %% #""' # ", &"  " "%+  %!&" ",  %% #""'

www.ti.com 1

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

functional block diagram

VCC RT CT
11 9 2 1
2 DTC

14 10
ERROR IN+ + 2 OUTPUT
AMPLIFIER 2 13 –
IN–
12
2 FEEDBACK Oscillator PWM
1/2 Vref COMP
5
1 FEEDBACK
Reference 16
REF
12 kΩ Voltage
15
SCP

170 kΩ UVLO
R
R
S

3
ERROR IN+ +
4 7
AMPLIFIER 1 IN– – 1 OUTPUT

PWM
COMP

6
1 DTC 8
GND

COMPONENT COUNT
Resistors 65
Capacitors 8
Transistors 105
JFETs 18

2 www.ti.com
 


 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

absolute maximum ratings over operating free-air temperature range†

Supply voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 V
Amplifier input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Collector output voltage, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 V
Collector output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 mA
Continuous power total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20°C to 85°C
Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 125°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

DISSIPATION RATING TABLE

TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C TA = 125°C
PACKAGE
POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING POWER RATING
D 1088 mW 8.7 mW/°C 696 mW 566 mW 218 mW
DB 775 mW 6.2 mW/°C 496 mW 403 mW —
N 1000 mW 8.0 mW/°C 640 mW 520 mW —
NS 500 mW 4.0 mW/°C 320 mW 260 mW —
PW 838 mW 6.7 mW/°C 536 mW 436 mW 168 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW

recommended operating conditions

MIN MAX UNIT
Supply voltage, VCC 3.6 50 V
Amplifier input voltage, VI 1.05 1.45 V
Collector output voltage, VO 50 V
Collector output current, IO 20 mA
Current into feedback terminal 45 µA
Feedback resistor, RF 100 kΩ
Timing capacitor, CT 150 15000 pF
Timing resistor, RT 5.1 100 kΩ
Oscillator frequency 1 500 kHz
C suffix –20 85
Operating
g free-air temperature,, TA Q suffix –40 125 °C
M suffix –55 125

www.ti.com 3

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,

f = 200 kHz (unless otherwise noted)
reference section
TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Output voltage (pin 16) IO = 1 mA 2.4 2.5 2.6 V
TA = –20°C to 25°C –0.1% ±1%
O tp t voltage
Output oltage change with
ith temperat
temperature
re
TA = 25°C to 85°C –0.2% ±1%
Input voltage regulation VCC = 3.6 V to 40 V 2 12.5 mV
Output voltage regulation IO = 0.1 mA to 1 mA 1 7.5 mV
Short-circuit output current VO = 0 3 10 30 mA
† All typical values are at TA = 25°C.

undervoltage lockout section

TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Upper threshold voltage (VCC) 2.72 V
Lower threshold voltage (VCC) 2.6 V
IO(ref)
O( f) = 0
0.1
1 mA
mA, TA = 25°C
Hysteresis (VCC) 80 120 mV
Reset threshold voltage (VCC) 1.5 1.9 V
† All typical values are at TA = 25°C.

short-circuit protection control section

TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Input threshold voltage (SCP) TA = 25°C 0.65 0.7 0.75 V
Standby voltage (SCP) No pullup 140 185 230 mV
Latched input voltage (SCP) No pullup 60 120 mV
Input (source) current VI = 0.7 V, TA = 25°C –10 –15 –20 µA
Comparator threshold voltage (FEEDBACK) 1.18 V
† All typical values are at TA = 25°C.

oscillator section
TL1451C
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Frequency CT = 330 pF, RT = 10 kΩ 200 kHz
Standard deviation of frequency CT = 330 pF, RT = 10 kΩ 10%
Frequency change with voltage VCC = 3.6 V to 40 V 1%
TA = –20°C to 25°C –0.4% ±2%
Frequency change with temperature
TA = 25°C to 85°C –0.2% ±2%
† All typical values are at TA = 25°C.

4 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

dead-time control section

TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Input bias current (DTC) 1 µA
Latch mode (source) current (DTC) TA = 25°C –80 –145 µA
Latched input voltage (DTC) IO = 40 µA 2.3 V
Zero duty cycle 2.05 2.25
Input threshold voltage at f = 10 kHz (DTC) V
Maximum duty cycle 1.2 1.45
† All typical values are at TA = 25°C.

error-amplifier section
TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Input offset voltage VO (FEEDBACK) = 1.25 V ±6 mV
Input offset current VO (FEEDBACK) = 1.25 V ±100 nA
Input bias current VO (FEEDBACK) = 1.25 V 160 500 nA
1.05
Common-mode
Common input
mode in ut voltage range VCC = 3.6 V to 40 V to V
1.45
Open-loop voltage amplification RF = 200 kΩ 70 80 dB
Unity-gain bandwidth 1.5 MHz
Common-mode rejection ratio 60 80 dB
Positive output voltage swing Vref–0.1 V
Negative output voltage swing 1 V
Output (sink) current (FEEDBACK) VID = –0.1 V, VO = 1.25 V 0.5 1.6 mA
Output (source) current (FEEDBACK) VID = 0.1 V, VO = 1.25 V –45 –70 µA
† All typical values are at TA = 25°C.

output section
TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Collector off-state current VO = 50 V 10 µA
Output saturation voltage IO = 10 mA 1.2 2 V
Short-circuit output current VO = 6 V 90 mA
† All typical values are at TA = 25°C.

pwm comparator section

TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Zero duty cycle 2.05 2.25
Input threshold voltage at f = 10 kHz (FEEDBACK) V
Maximum duty cycle 1.2 1.45
† All typical values are at TA = 25°C.

total device
TL1451AC
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Standby supply current Off-state 1.3 1.8 mA
Average supply current RT = 10 kΩ 1.7 2.4 mA
† All typical values are at TA = 25°C.

www.ti.com 5

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

electrical characteristics over recommended operating free-air temperature range, VCC = 6 V,

f = 200 kHz (unless otherwise noted)
reference section
TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
TA = 25°C 2.40 2.50 2.60
O tp t voltage
Output oltage (pin 16) IO = 1 mA V
TA = MIN and 125°C 2.35 2.46 2.65
Output voltage change with temperature –0.63% *±4%
TA = 25°C 2.0 12.5
Input
In ut voltage regulation VCC = 3.6 V to 40 V TA = 125°C 0.7 15 mV
TA = MIN 0.3 30
TA = 25°C 1.0 7.5
Output
Out ut voltage regulation IO = 0.1 mA to 1 mA TA = 125°C 0.3 14 mV
TA = MIN 0.3 20
Short-circuit output current VO = 0 3 10 30 mA
*These parameters are not production tested.
† All typical values are at TA = 25°C unless otherwise indicated.

undervoltage lockout section

TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
TA = 25°C 2.72
Upper
U er threshold voltage (VCC) TA = 125°C 1.70 V
TA = MIN 3.15
TA = 25°C 2.60
Lower threshold voltage (VCC) TA = 125°C 1.65 V
TA = MIN 3.09
TA = 25°C 80 120
Hysteresis (VCC) TA = 125°C 10 50 mV
TA = MIN 10 60
TA = 25°C 1.50
Reset threshold voltage
g (V
( CC) TA = 125°C 0.95 V
TA = MIN 1.50
† All typical values are at TA = 25°C unless otherwise indicated.

6 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

short-circuit protection control section

TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
TA = 25°C 650 700 750
Input
In ut threshold voltage (SCP) TA = 125°C 400 478 550 mV
TA = MIN 800 880 950
Standby voltage (SCP) 140 185 230 mV
TA = 25°C 60 120
Latched input
in ut voltage (SCP) TA = 125°C 70 120 mV
TA = MIN 60 120
Equivalent timing resistance 170 kΩ
Comparator threshold voltage (FEEDBACK) 1.18 V
† All typical values are at TA = 25°C unless otherwise indicated.

oscillator section
TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
TA = 25°C 200
CT = 330 pF,
F
Frequency TA = 125°C 195 kHz
RT = 10 kΩ
TA = MIN 193
Standard deviation of frequency CT = 330 pF, RT = 10 kΩ 2%
TA = 25°C 1%
Frequency change with voltage VCC = 3.6 V to 40 V TA = 125°C 1%
TA = MIN 3%
Frequency change with temperature 1.37% *±10%
*These parameters are not production tested.
† All typical values are at TA = 25°C unless otherwise indicated.

dead-time control section

TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
TA = 25°C 1
Inp t bias current
Input c rrent (DTC) µA
A
TA = MIN and 125°C 3
Latch mode (source) current (DTC) –80 –145 µA
TA = 25°C 2.30
input
Latched in ut voltage (DTC) TA = 125°C 2.22 2.32 V
TA = MIN 2.28 2.40
Zero duty cycle 2.05 *2.25
Input threshold voltage at f = 10 kHz (DTC) V
Maximum duty cycle *1.20 1.45
*These parameters are not production tested.
† All typical values are at TA = 25°C unless otherwise indicated.

www.ti.com 7

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

error-amplifier section
TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
TA = 25°C ±6
Input
In ut offset voltage VO (FEEDBACK) = 1.25 V TA = 125°C ±10 mV
TA = MIN ±12
TA = 25°C ±100
Input
In ut offset current VO (FEEDBACK) = 1.25 V TA = 125°C ±100 nA
TA = MIN ±200
TA = 25°C 160 500
Input
In ut bias current VO (FEEDBACK) = 1.25 V TA = 125°C 100 500 nA
TA = MIN 142 700
1.05
Common-mode
Common mode in
input
ut voltage range VCC = 3.6 V to 40 V to V
1.45
TA = 25°C 70 80
Open-loop
O en loo voltage am
amplification
lification RF = 200 kΩ TA = 125°C 70 80 dB
TA = MIN 64 80
Unity-gain bandwidth 1.5 MHz
Common-mode rejection ratio 60 80 dB
Positive output voltage swing 2 V
Negative output voltage swing 1 V
TA = 25°C 0.5 1.6
Output
Out ut (sink) current (FEEDBACK) VID = –0.1
0.1 V, VO = 1.25 V TA = 125°C 0.4 1.8 mA
TA = MIN 0.3 1.7
TA = 25°C –45 –70
Output ((source)) current ((FEEDBACK)) VID = 0.1 V,, VO = 1.25 V TA = 125°C –25 –50 µA
µ
TA = MIN –15 –70
† All typical values are at TA = 25°C unless otherwise indicated.

output section
TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Collector off-state current VO = 50 V 10 µA
TA = 25°C 1.20 2.0
Output
Out ut saturation voltage TA = 125°C 1.60 2.4 V
TA = MIN 1.36 2.2
Short-circuit output current VO = 6 V 90 mA
† All typical values are at TA = 25°C unless otherwise indicated.

pwm comparator section

TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Zero duty cycle 2.05 *2.25
Input threshold voltage at f = 10 kHz (FEEDBACK) V
Maximum duty cycle *1.20 1.45
*These parameters are not production tested.
† All typical values are at TA = 25°C unless otherwise indicated.

8 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

total device
TL1451AQ, TL1451AM
PARAMETER TEST CONDITIONS UNIT
MIN TYP† MAX
Standby supply current Off-state 1.3 1.8 mA
Average supply current RT = 10 kΩ 1.7 2.4 mA
† All typical values are at TA = 25°C unless otherwise indicated.

PARAMETER MEASUREMENT INFORMATION

Test
S1 Input VCC = 5 V
RL
CPE 0.47 µF 4.7 kΩ OUT1
RL

4.7 kΩ OUT2
16 15 14 13 12 11 10 9

TL1451A

1 2 3 4 5 6 7 8

CT RT
330 pF 10 kΩ

Test
Input

Figure 1. Test Circuit

Oscillator Triangle Waveform

Error Amplifier Output 2.0 V
Dead-Time Input Voltage 1.6 V
1.4 V
Short-Circuit Protection 1.25 V
Comparator Input Voltage H
PWM Comparator Output Voltage
L
Dead Time 100%
H
Output Transistor Collector
Waveform L

0.6 V
Protection Enable
Terminal Waveform 0V
tpe†
Short-Circuit Protection H
Comparator Output L
3.6 V
Power Supply Voltage 2.8 V TYP
0V
† Protection Enable Time, tpe = (0.051 x 106 x Cpe) in seconds

Figure 2. TL1451A Timing Diagram

www.ti.com 9

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
TRIANGLE OSCILLATOR FREQUENCY OSCILLATOR FREQUENCY VARIATION
vs vs
TIMING RESISTANCE FREE-AIR TEMPERATURE
1M 3
VCC = 5 V VCC = 3.6 V
osc – Triangle Oscillator Frequency – Hz

f osc – Oscillator Frequency Variation – %

TA = 25°C RT = 10 kΩ
2 CT = 330 pF
fosc = 200 kHz

ÎÎÎÎÎÎÎÎÎÎÎÎ
CT = 150 pF
100 k 1

ÎÎÎÎÎÎÎÎÎÎÎÎ
0
ÎÎÎÎÎÎÎÎÎÎÎÎ
CT = 1500 pF
ÎÎÎÎÎÎÎÎÎÎÎÎ
10 k –1
ÎÎÎÎÎÎÎÎÎÎÎÎ
–2
ÎÎÎÎÎ
ffosc

∆afosc
CT = 15000 pF

1k –3
1k 4k 10 k 40 k 100 k 400 k 1M –25 0 25 50 75 100
RT – Timing Resistance – Ω TA – Free-Air Temperature – °C

Figure 3 Figure 4

TRIANGLE WAVEFORM SWING VOLTAGE TRIANGLE WAVEFORM PERIOD

vs vs
TIMING CAPACITANCE TIMING CAPACITANCE
2.6 102
VCC = 5 V VCC = 5 V
2.4 RT = 5.1 kΩ RT = 5.1 kΩ
Triangle Waveform Swing Voltage – V

TA = 25°C TA = 25°C
uSs

2.2
Triangle Waveform Period – µ

2 101

1.8

1.6

1.4 100

1.2

0.8 10–1
101 102 103 104 105 101 102 103 104 105
CT – Timing Capacitance – pF CT – Timing Capacitance – pF

Figure 5 Figure 6

10 www.ti.com
 


 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS

REFERENCE OUTPUT VOLTAGE VARIATION REFERENCE OUTPUT VOLTAGE VARIATION

vs vs
FREE-AIR TEMPERATURE FREE-AIR TEMPERATURE
30 30
avref – Reference Output Voltage Variation – mV

avref – Reference Output Voltage Variation – mV

VCC = 3.6 V VCC = 40 V
II(ref) = 1 mA II(ref) = 1 mA
20 20

10
ÎÎÎÎÎ 10
ÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ
0
ÎÎÎÎÎÎÎÎÎÎÎÎ 0
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎ
–10
ÎÎÎÎÎÎÎÎÎÎÎÎ –10
ÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ ÎÎÎÎÎÎ
ÁÁ ÁÁ – 20

ÁÁ ÁÁ
– 20
∆VO(ref)

ÁÁ ÁÁ ∆VO(ref)
ÁÁ ÁÁ
– 30 – 30
– 25 0 25 50 75 100 – 25 0 25 50 75 100
TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C

Figure 7 Figure 8

REFERENCE OUTPUT VOLTAGE DROPOUT VOLTAGE VARIATION

vs vs
SUPPLY VOLTAGE FREE-TEMPERATURE
3 1.1
TA = 25°C II(ref) = 1 mA
Vref – Reference Output Voltage – V

2.5 1
Dropout Voltage Variation – V

2 0.9

1.5 0.8

ÁÁ
1 0.7
VO(ref)

ÁÁ
ÁÁ
0.5 0.6

0
0 5 10 15 20 25 30 35 40 – 25 0 25 50 75 100
VCC – Supply Voltage – V TA – Free-Air Temperature – °C

Figure 9 Figure 10

www.ti.com 11

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
UNDERVOLTAGE LOCKOUT
HYSTERESIS CHARACTERISTICS UNDERVOLTAGE LOCKOUT CHARACTERISTIC
6 3.5 300
TA = 25°C

Undervoltage Lockout Hystersis Voltage – mV

TA = 85°C TA = –20°C

Undervoltage Lockout Threshold Voltage – V

3.25 250
– Output Collector Voltage – V

5 Threshold Voltage –VTH

(Left Scale)
3 200
4 Threshold Voltage –VTL
(Left Scale)
2.75 150
3
5V
2.5 100
RL Hysteresis Voltage

ÁÁ
2 (Right Scale)
7,10 I = IO 2.25 50

ÁÁ
VVCE
CE

8 VDE

ÁÁ
1
2 0
IO = 10 mA
0
0 1 2 3 4 5 –25 0 25 50 75 100
VCC – Supply Voltage – V TA – Free-Air Temperature – °C

Figure 11 Figure 12

SHORT-CIRCUIT PROTECTION CHARACTERISTICS

1.30 3 RS – Latch Reset Supply Voltage – V

Comparator Threshold Voltage – V

1.25 Short-Circuit Protection 2.5

Latch Reset Supply Voltage
(Right Scale)

1.20 2

Short-Circuit Protection
1.15 1.5
Comparator Threshold Voltage
(Left Scale)

1.10 1
– 25 0 25 50 75 100
TA – Free-Air Temperature – °C

Figure 13

12 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
PROTECTION ENABLE TIME
vs
PROTECTION ENABLE CAPACITANCE
18

15

t pe – Protection Enable Time – s

12

6
tpe

0
0 50 100 150 200 250
CPE – Protection Enable Capacitance – µF

SCP Vref
15 16
170 kΩ Vref Vref

Short-circuit
Protection 12 kΩ
Comparator S R
CPE Protection U.V.L.O.
ERROR AMP 1 Latch
ERROR AMP 2

+
1.25 V
–

Figure 14

www.ti.com 13

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS

ERROR AMP MAXIMUM OUTPUT VOLTAGE SWING OPEN-LOOP VOLTAGE AMPLIFICATION

vs vs
FREQUENCY FREQUENCY
2.25 90
Error Amp Maximum Output Voltage Swing – V

VCC = 5 V VCC = 5 V
2 TA = 25°C 80 TA = 25°C

Open-Loop Voltage Amplification – dB

1.75 70

1.5 60

1.25 50

1 40

0.75 30

0.5 20

0.25 10

0 0
1k 10 k 100 k 1M 10 M 100 1k 10 k 100 k 1M 2M
f – Frequency – Hz f – Frequency – Hz

Figure 15 Figure 16

GAIN (AMPLIFIER IN
UNITY-GAIN CONFIGURATION)
vs
FREQUENCY
10
VCC = 5 V
TA = 25°C
5

0
G – Gain – dB

–5

–10

–15

–20
1k 10 k 100 k 1M 10 M
f – Frequency – Hz

Figure 17

14 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
70
VCC = 5 V CX: 47 pF
Rref = 150 Ω 470 pF
60 Cref = 470 pF 4700 pF
TA = 25°C
Phase Shift
Closed-Loop Gain – dB

50 (Right Scale)
Closed-Loop Gain 0°

Phase Shift
40 (Left Scale) –10°
–20°
30 –30°
–40°
20 –50°
–60°
10 –70°
–80°
0 –90°
100 1k 10 k 100 k 1M
f – Frequency – Hz

Vref
+
–
39 kΩ Cx Rref

Cref
39 kΩ

Test Circuit

Figure 18

www.ti.com 15

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
70
VCC = 5 V CX: 47 pF
Rref = 15 Ω 470 pF
60 Cref = 470 pF 4700 pF
TA = 25°C
Phase Shift
Closed-Loop Gain – dB

50
(Right Scale)
0°
Closed-Loop Gain

Phase Shift
40 (Left Scale) –10°
–20°
30 –30°
–40°
20 –50°
–60°
10 –70°
–80°
0 –90°
100 1k 10 k 100 k 1M
f – Frequency – Hz

Vref
+
–
39 kΩ Cx Rref

Cref
39 kΩ

Test Circuit

Figure 19

16 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
70
VCC = 5 V CX: 47 pF
Rref = 15 Ω 470 pF
60 Cref = 470 pF 4700 pF
TA = 25°C
Closed-Loop Gain – dB

50 Phase Shift
Closed-Loop Gain (Right Scale) 0°

Phase Shift
40 (Left Scale) –10°
–20°
30 –30°
–40°
20 –50°
–60°
10 –70°
–80°
0 –90°
100 1k 10 k 100 k 1M
f – Frequency – Hz

Vref
+
–
39 kΩ Cx Rref

Cref
39 kΩ

Test Circuit

Figure 20

www.ti.com 17

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
CLOSED-LOOP GAIN AND PHASE SHIFT
vs
FREQUENCY
70
VCC = 5 V
Cref = 470 pF
60 TA = 25°C
Closed-Loop Gain – dB

50
0°

Phase Shift
40 Closed-Loop Gain –10°
Phase Shift
(Left Scale) –20°
(Right Scale)
30 –30°
–40°
20 –50°
–60°
10 –70°
–80°
0 –90°
100 1k 10 k 100 k 1M
f – Frequency – Hz

Vref
+
–
39 kΩ

Cref
39 kΩ

Test Circuit

Figure 21

18 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
OUTPUT SINK CURRENT
vs
COLLECTOR OUTPUT SATURATION VOLTAGE
120
TA = –20°C
110
TA = 25°C
100
90 TA = 85°C
Output Sink Current – mA
80
70

60
50

40
30

20
VCC = 3.6 V
10

0
0 5 10 15 20
Collector Output Saturation Voltage – V

Figure 22

MAXIMUM OUTPUT VOLTAGE SWING

vs
FREE-AIR TEMPERATURE
VO(ref) –0.01 1 Vref
VOM – Maximum Output Voltage Swing – V

VOM – Maximum Output Voltage Swing – V

VO(ref) –0.02 0.9 33 kΩ

Maximum Output Voltage +

VO(ref) –0.03 Swing (Right Scale) 0.8 –
33 kΩ
RL

VO(ref) –0.04 0.7 100 kΩ

Vvom – 1
Maximum Output VCC = 3.6 V
VO(ref) –0.05 0.6
Voltage Swing (Right Scale) RL = 100 kΩ
VOM+1 = 1.25 V
VO(ref) –0.06 0.5 VOM –1 = 1.15 V (Right Scale)
VOM –1 = 1.35 V (Left Scale)

TEST CIRCUIT
VO(ref) –0.07
–25 0 25 50 75 100
TA – Free-Air Temperature – °C

Figure 23

www.ti.com 19

 

 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

TYPICAL CHARACTERISTICS
OUTPUT TRANSISTOR ON DUTY CYCLE STANDBY CURRENT
vs vs
DEAD-TIME INPUT VOLTAGE SUPPLY VOLTAGE
0
VCC = 3.6 V TA = 25°C
10 RT = 10kΩ 2
Output Transistor “On” Duty Cycle – %

CC (Standby) – Standby Current – mA

CT = 330 pF
20
1.75
30
1.5
40
1.25
50
1
60
0.75
70

ÁÁ
0.5
80

90

100
ÁÁ IICC 0.25

0
0 0.5 1 1.5 2 2.5 3 3.5 4 0 10 20 30 40
Dead-Time Input Voltage – V VCC – Supply Voltage – V

Figure 24 Figure 25

STANDBY CURRENT MAXIMUM CONTINUOUS POWER DISSIPATION

vs vs
FREE-AIR TEMPERATURE FREE-AIR TEMPERATURE
1200
Maximum Continuous Power Dissipation – mW

Average Supply Current 1100

2 16-Pin N Plastic Dip
VCC = 6 V, RT = 10 kΩ,
1000
CT = 330 pF
1.75 Thermal Resistance
900
I CC – Supply Current – mA

125°C/W
1.5 800
Stand-By Current, VCC = 40 V, No Load
700
1.25
600
Stand-By Current, VCC = 3.6 V, No Load 16-Pin NS Plastic SO
1 500

ÁÁ 400

ÁÁ
0.75
Thermal Resistance
ICC

300
0.5 250°C/W
200
0.25 100

0 0
–25 0 25 50 75 100 –25 0 25 50 75 100
TA – Free-Air Temperature – °C TA – Free-Air Temperature

Figure 26 Figure 27

20 www.ti.com



 
 
 
 


SLVS024E – FEBRUARY 1983 – REVISED NOVEMBER 1999

APPLICATION INFORMATION
VCC

220 kΩ 150 Ω
470 Ω L1

0.47 µF 50 kΩ 33 kΩ 330 pF
33 kΩ R1 R3
R2 Step-Up
C2 Output

33 kΩ 33 kΩ R4

C1
500 pF
Vref

16 15 14 13 12 11 10 9

TL1451A

1 2 3 4 5 6 7 8
470 Ω
470 Ω

R5
C5 220 Ω 1 µF L2
500
pF
R6
Step-Down
C4 Output
33 kΩ 470 Ω R7
33 kΩ

NOTE A: Values for R1 through R7, C1 through C4, and L1 and L2 depend upon individual application.

Figure 28. High-Speed Dual Switching Regulator

www.ti.com 21
 PACKAGE OPTION ADDENDUM

www.ti.com 24-Jan-2013

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Qty Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Top-Side Markings Samples
(1) Drawing (2) (3) (4)

5962-9958401Q2A OBSOLETE LCCC FK 20 TBD Call TI Call TI -55 to 125

5962-9958401QEA OBSOLETE CDIP J 16 TBD Call TI Call TI -55 to 125
TL1451ACD ACTIVE SOIC D 16 40 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 TL1451AC
& no Sb/Br)
TL1451ACDBLE NRND SSOP DB 16 TBD Call TI Call TI -20 to 85
TL1451ACDBR ACTIVE SSOP DB 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 T1451A
& no Sb/Br)
TL1451ACDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 T1451A
& no Sb/Br)
TL1451ACDG4 ACTIVE SOIC D 16 40 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 TL1451AC
& no Sb/Br)
TL1451ACDR ACTIVE SOIC D 16 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 TL1451AC
& no Sb/Br)
TL1451ACDRG4 ACTIVE SOIC D 16 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 TL1451AC
& no Sb/Br)
TL1451ACN ACTIVE PDIP N 16 25 Pb-Free CU NIPDAU N / A for Pkg Type -20 to 85 TL1451ACN
(RoHS)
TL1451ACNE4 ACTIVE PDIP N 16 25 Pb-Free CU NIPDAU N / A for Pkg Type -20 to 85 TL1451ACN
(RoHS)
TL1451ACNSR ACTIVE SO NS 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 TL1451A
& no Sb/Br)
TL1451ACNSRG4 ACTIVE SO NS 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 TL1451A
& no Sb/Br)
TL1451ACPW ACTIVE TSSOP PW 16 90 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 T1451A
& no Sb/Br)
TL1451ACPWG4 ACTIVE TSSOP PW 16 90 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 T1451A
& no Sb/Br)
TL1451ACPWLE OBSOLETE TSSOP PW 16 TBD Call TI Call TI -20 to 85
TL1451ACPWR ACTIVE TSSOP PW 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 T1451A
& no Sb/Br)
TL1451ACPWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -20 to 85 T1451A
& no Sb/Br)
TL1451AMFKB OBSOLETE LCCC FK 20 TBD Call TI Call TI -55 to 125

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 24-Jan-2013

Orderable Device Status Package Type Package Pins Package Qty Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Top-Side Markings Samples
(1) Drawing (2) (3) (4)

TL1451AMJB OBSOLETE CDIP J 16 TBD Call TI Call TI -55 to 125

TL1451AQD ACTIVE SOIC D 16 40 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 TL1451AQ
& no Sb/Br)
TL1451AQDG4 ACTIVE SOIC D 16 40 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 1451AQ
& no Sb/Br)
TL1451AQDR ACTIVE SOIC D 16 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 TL1451AQ
& no Sb/Br)
TL1451AQDRG4 ACTIVE SOIC D 16 2500 Green (RoHS CU NIPDAU Level-1-260C-UNLIM 1451AQ
& no Sb/Br)
TL1451CDBR ACTIVE SSOP DB 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM T1451
& no Sb/Br)
TL1451CDBRG4 ACTIVE SSOP DB 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM T1451
& no Sb/Br)
TL1451CN ACTIVE PDIP N 16 25 Pb-Free CU NIPDAU N / A for Pkg Type TL1451CN
(RoHS)
TL1451CNE4 ACTIVE PDIP N 16 25 Pb-Free CU NIPDAU N / A for Pkg Type TL1451CN
(RoHS)
TL1451CNS ACTIVE SO NS 16 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM TL1451
& no Sb/Br)
TL1451CNSG4 ACTIVE SO NS 16 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM TL1451
& no Sb/Br)
TL1451CNSR ACTIVE SO NS 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM TL1451
& no Sb/Br)
TL1451CNSRG4 ACTIVE SO NS 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM TL1451
& no Sb/Br)
TL1451INSR ACTIVE SO NS 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM TL1451I
& no Sb/Br)
TL1451INSRG4 ACTIVE SO NS 16 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM TL1451I
& no Sb/Br)

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

Addendum-Page 2
 PACKAGE OPTION ADDENDUM

www.ti.com 24-Jan-2013

(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)

(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
Only one of markings shown within the brackets will appear on the physical device.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF TL1451A, TL1451AM :

• Catalog: TL1451A
• Automotive: TL1451A-Q1, TL1451A-Q1
• Enhanced Product: TL1451A-EP, TL1451A-EP
• Military: TL1451AM

NOTE: Qualified Version Definitions:

• Catalog - TI's standard catalog product

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
• Enhanced Product - Supports Defense, Aerospace and Medical Applications

Addendum-Page 3
 PACKAGE OPTION ADDENDUM

www.ti.com 24-Jan-2013

• Military - QML certified for Military and Defense Applications

Addendum-Page 4
 PACKAGE MATERIALS INFORMATION

www.ti.com 14-Mar-2013

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TL1451ACDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
TL1451ACDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451ACDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451ACNSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
TL1451ACPWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TL1451AQDR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451AQDRG4 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TL1451CDBR SSOP DB 16 2000 330.0 16.4 8.2 6.6 2.5 12.0 16.0 Q1
TL1451CNSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1
TL1451INSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 14-Mar-2013

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TL1451ACDBR SSOP DB 16 2000 367.0 367.0 38.0
TL1451ACDR SOIC D 16 2500 333.2 345.9 28.6
TL1451ACDR SOIC D 16 2500 367.0 367.0 38.0
TL1451ACNSR SO NS 16 2000 367.0 367.0 38.0
TL1451ACPWR TSSOP PW 16 2000 367.0 367.0 35.0
TL1451AQDR SOIC D 16 2500 367.0 367.0 38.0
TL1451AQDRG4 SOIC D 16 2500 367.0 367.0 38.0
TL1451CDBR SSOP DB 16 2000 367.0 367.0 38.0
TL1451CNSR SO NS 16 2000 367.0 367.0 38.0
TL1451INSR SO NS 16 2000 367.0 367.0 38.0

Pack Materials-Page 2
 MECHANICAL DATA

MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001

DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE

28 PINS SHOWN

0,38
0,65 0,15 M
0,22
28 15

0,25
0,09
5,60 8,20
5,00 7,40

Gage Plane

1 14 0,25

A 0°–ā8° 0,95
0,55

Seating Plane

2,00 MAX 0,05 MIN 0,10

PINS **
14 16 20 24 28 30 38
DIM

A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90

A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30

4040065 /E 12/01

NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated