Partner: Epson

Model: EB-X11
Device Type: LCD Projector

GENERAL INFORMATION
SIMPLWINDOWS NAME: Epson EB-X11 v1.0

CATEGORY: TV/Video Projector

VERSION: 1.0

This module will control the Epson EB-X11 via RS-232. Functions include Power,
Source Select, A/V mute, Aspect Ratio, Freeze, Brightness, Contrast, Sharpness,
Volume and display elapsed Lamp Hour usage.
This module was tested with the EB-X11. Epson uses the same protocol on most of
their projectors. This module should also work on the following models:
SUMMARY:
• PowerLite X11
• EB-C25XE
• PowerLite S11
• EB-S11
• EB-C10SE

This module will control the Epson EB-X11 Projector. True feedback is provided for
power, input sources, a/v mute, freeze, aspect ratio, color mode and picture
settings. When any command is sent to the projector, it will acknowledge that the
command was processed properly and the corresponding feedback will be reflected
at the outputs of this module.
If it is desired to poll the projector for power state, you can assert the Poll_Enable
input. When this input is high, the projector will be polled every 15 seconds to
determine the state of power. If it is desired to poll the projector for picture setting
changes made using the IR remote control, or by the controls on the projector itself,
GENERAL NOTES:
you can assert the Poll_Settings input. When this input is high, the projector will be
polled every 45 seconds to determine the state of input source, picture mute, freeze,
aspect ratio, color mode, brightness, contrast, sharpness, color, tint, volume and
elapsed lamp hours. Typically, you could enable either polling option when the
projector's particular control page is active and displayed on a touch panel. You
would then disable polling at other times.
NOTE: This module depends on feedback from the device. You cannot comment out
the From_Device. This module is System Builder compatible.

CRESTRON HARDWARE REQUIRED: X-Series Processor, CNX-COM2, ST-COM, 2-Series Processor, C2COM3, MC3

RS232
Baud: 9600
SETUP OF CRESTRON HARDWARE: Parity: N
Data Bits: 8
Stop Bits: 1

VENDOR FIRMWARE: None

VENDOR SETUP: None

CABLE DIAGRAM: CNSP-124

CONTROL:
Power_<On/Off/Toggle> D Pulse to turn projector on or off.

Input_* D Pulse to select the desired source.

A/V_Mute_<On/Off/Toggle> D Pulse to turn A/V mute on or off.

Freeze_<On/Off/Toggle> D Pulse to turn freeze function on or off.

Aspect_* D Pulse to select desired aspect ratio.

Color_Mode_* D Pulse to select desired color mode.

Contrast_<Up/Down> D Press to adjust the contrast level.

Brightness_<Up/Down> D Press to adjust the brightness level.

Sharpness_<Up/Down> D Press to adjust the sharpness level.

Volume_<Up/Down> D Press to adjust the volume level.

Auto_Sync D Pulse to trigger the auto sync function.

Poll_Enable D Latch high to enable polling for power status.

Poll_Settings D Latch high to enable polling for remaining settings.

From_Device S Serial signal to be routed from an RS-232C port.

FEEDBACK:
Power_Is_<On/Off> D True feedback indicating current power state.

Input_Is_* D True feedback indicating current selected input source.

A/V_Mute_Is_<On/Off> D True feedback indicating current A/V mute state.

Freeze_Is_<On/Off> D True feedback indicating current freeze status.

Aspect_Is_* D True feedback indicating current aspect ratio.

Color_Mode_Is_* D True feedback indicating current color mode setting.

Contrast_Gauge A Analog value indicating current contrast level. For gauge on touchpanel

Brightness_Gauge A Analog value indicating current brightness level. For gauge on touchpanel.

Sharpness_Gauge A Analog value indicating current sharpness level. For gauge on touchpanel.

Volume_Gauge A Analog value indicating current volume level. For gauge on touchpanel.

Lamp_Hours A Analog value indicating current lamp hours. For digital gauge on touchpanel.

To_Device S Serial data signal to be routed to a 2 way com port.

TESTING:
OPS USED FOR TESTING: 4.003.0015

SIMPL WINDOWS USED FOR TESTING: 3.12.14

CRES DB USED FOR TESTING: 27.00.010.00

DEVICE DB USED FOR TESTING: 36.02.002.00

SYMBOL LIBRARY USED FOR TESTING: 743

SAMPLE PROGRAM: Epson EB-X11 v1.0 Demo PRO2

REVISION HISTORY: v1.0