SERVICE MANUAL

MODEL FG-8110
SWEEP/FUNCTION GENERATOR
 CONTENTS

1. PERFORMANCE CHECK PROCEDURE

2. ADJUSTMENT PROCEDURE

3. TROUBLESHOOTING PROCEDURE

4. PARTS LIST

5. CIRCUIT DIAGRAM

2
1. PERFORMANCE CHECK PROCEDURE

1-1. General
This section contains the Procedures required to check and maintain specified instrument
performance. The adjustments should be performed at an ambient temperature of
23°C ±5°C and a relative humidity of less than 60%. It allows the instrument to stabilize at
this environment for a minimum of 30 minutes.

1-2. Equipment's required

Table 1-1 is shown test equipment's required.

Table 1-1 Equipment's required

No Equipment name Specification Remark

.
1. Frequency Counter DC to 60 MHz
2. Oscilloscope DC to 20 MHz
3. AC Millivolt Meter Up to 30 Vrms
4. Distortion Analyzer 0.01% 100kHz
5. DC Power Supply DC 0 to 10V
6. Signal Generator 200mHz to 110 MHz
7. FEEDTHROUGH TERMINATION 50 Ω

1-3. Performance check

1-3-1. OUTPUT FREQUENCY RANGE

SPECIFICATION
0.1 Hz TO 10 MHz

ACCURACY
+/- 5 % OF SETTING

EQUIPMENT
FREQUENCY COUNTER
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
2. Set 8210 as follows;

3
 - Function ; SINE WAVE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the frequency counter to output terminal.
3. Set the frequency counter to frequency measurement.
4. Set the output frequency of this product by FREQUENCY RANGE and DIAL and verify
counter frequency reading as follows;

8210 setting Counter reading

Range Frequency
1M 10.000 MHz
100.00 kHz
100k 1.0000 MHz
10.000 kHz
10k 100.00 kHz
1.0000 kHz
1k 10.000 kHz
100.00 Hz
100 1.0000 kHz
10.000 Hz
10 100.00 Hz
1.0000 Hz
1 10.000 Hz
100.00 mHz

** For reading less than 200 mHz, you can read by period value.
200mHz ; 5.000 sec
100 mHz ; 10.000 sec

1-3-2. AMPLITUDE AND ATTENUATION

SPECIFICATION
Amplitude range ;100mVp-p to 10Vp-p IN TO 50Ω
Attenuation ;20 dB

ACCURACY
Lower than 100mVp-p(IN TO 50Ω) at MIN.
Higher than 10Vp-p(IN TO 50Ω) at MAX.

4
EQUIPMENT
Oscilloscope
AC Millivoltmeter
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω

PROCEDURE
1. Set this product as follows;
- Function ; SINE WAVE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the oscilloscope through FEEDTHROUGH TERMINATION 50 Ω
to output terminal.
3. Set Amplitude Control to Min. position and check the output level is lower than
100mVp-p(less 5div in 20mV/div).
4. Set Amplitude Control to Max. position and check the output level is higher than
10Vp-p(higher than 4div in 5V/div).
5. Set Amplitude Control to Min. position and connect AC Millivoltmeter to output
terminal.
6. Set the Range of AC millivoltmeter to 3V range and adjust Amplitude control for
0dB reading on AC millivoltmeter.
7. Push in “20dB ATT switch” and check the reading of AC Millivoltmeter is -20 dB.

1-3-3. SINE WAVE CHARACTERISTICS

SPECIFICATION
Total harmonic Distortion(THD) ; ≤ 1 % (10Hz to 100kHz)

EQUIPMENT
Distortion analyzer
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
1. Set this product as follows;
- Function ; SINE WAVE ( )
- ATT ; 0 dB(PULL OUT)

5
 - AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the distortion analyzer to output terminal.
3. Check the distortions of output signal are less than 1% from 10Hz to 100kHz.

1-3-4. TRIANGLE/SQUARE WAVE CHARACTERISTICS

SPECIFICATION
Linearity of Triangle Wave ; ≥ 99 % (10Hz to 100kHz)
Rise and Fall Time of Square Wave ; Less than 120nS at 10MHz Max. output level

EQUIPMENT
Oscilloscope
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
1. Set this product as follows;
- Function ; TRIANGLE WAVE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the oscilloscope to output terminal.
3. Check the linearity of Triangle wave from 10Hz to 100kHz.
4. Change the function to “SQUARE WAVE( )” and check the rise and fall time at
10MHz Max. output level.

1-3-5. TTL OUTPUT

SPECIFICATION
TTL OUTPUT - Rise and Fall Time ; Less than 25nS
- Output Level ; TTL LEVEL (H ≥ 2.4V , L ≤ 0.4V)

EQUIPMENT
Oscilloscope
BNC CABLE

6
PROCEDURE
1. Set this product as follows;
- FREQ. RANGE ; 10k
- FREQ. DIAL ; 10kHz
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)

3. Set the oscilloscope to 1V/div, 5uS/div and connect to TTL output terminal.
4. Check the rise and fall time of TTL SQUARE WAVE on CRT( 5div ).

1-3-5. DC OFFSET CONTROL

SPECIFICATION
MIN. ; lower than -10 V DC (Open circuit)
MAX. ; higher than +10 V DC (Open circuit)

EQUIPMENT
Oscilloscope
BNC CABLE

PROCEDURE
1. Set this product as follows;
- Function ; SQUARE ( )
- ATT ; 0 dB(PULL OUT)
- FREQ. RANGE ; 10k
- FREQ. DIAL ; 10kHz
- AMPLITUDE ; CENTER

2. Set Oscilloscope to 5V/DIV, 10uS/DIV, DC Coupling and connect to output terminal.

3. Adjust Amplitude Control for 2DIV on CRT.
4. Pull out “DC OFFSET” Control and set to “MIN.” position and check the DC OFFSET
level is lower than -10V(Lower than -2DIV).
5. Set “DC OFFSET” Control to “MAX.” position and check the DC OFFSET level is higher
than +10V(Higher than +2DIV).

1-3-6. SYMMETRY CONTROL

SPECIFICATION
MIN. ; lower than 1:10
MAX. ; higher than 10:1

7
EQUIPMENT
Oscilloscope
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
1. Set this product as follows;
- Function ; SQUARE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the oscilloscope to output terminal.
3. Set the output frequency to 10kHz.
4. Pull out SYM Control and adjust to Min. position. And check the symmetry(duty
ratio) is “lower than 1:10”.
5. Adjust SYM Control to Max. position and check the symmetry(duty ratio) is”higher
than 10:1”.

1-3-7. SWEEP FUNCTION

SPECIFICATION
Sweep Width ; 1:1 to 100:1
Sweep Rate ; 0.5Hz to 50Hz(20mS to 2 S)

EQUIPMENT
Oscilloscope
Frequency Counter
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
1. Set this product as follows;
- Function ; SINE WAVE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
2. Connect the oscilloscope and Frequency Counter to output terminal.

8
3. Set Freq. Range to 10k and adjust Freq. Dial to 1.00 kHz (Start Frequency).
4. Pull out SWIDTH Control and adjust to max. position ( 100kHz, Stop frequency).
5. Adjust Sweep Rate Control for desired rate and check sweep operating.

1-3-8. VCF IN FUNCTION

SPECIFICATION
Out-put frequency should be changed from minimum frequency to maximum frequency in
each frequency range by changing VCF INPUT Voltage from 0 to 10V DC.

EQUIPMENT
Power supply
BNC CABLE

PROCEDURE
1. Set this product as follows;
- Function ; SINE WAVE ( )
- Frequency Range ; 10K
- Frequency Control ; Max.
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
2. Set Power Supply to “0V” and connect to “VCF IN” Terminal.
3. Check the output frequency is “1.00kHz ± 0.2kHz”.
4. Increase the output voltage of Power Supply up to +10V and check the output
frequency as following table.
VCF Voltage Output Frequency Tolerance
0 1.000 kHz ± 0.2kHz
2.000 V 20.00 kHz ± 4 kHz
4.000 V 40.00 kHz ± 8 kHz
6.000 V 60.00 kHz ± 12 kHz
8.000 V 80.00 kHz ± 16 kHz
10.00 V 100.00 kHz ± 20 kHz

1-3-9. FREQUENCY COUNTER

SPECIFICATION
Frequency range ; 200mHz to 110MHz
Input sensitivity ; 100mVrms

EQUIPMENT

9
Signal generator

PROCEDURE
1. Set the COUNT to EXT(PUSH IN).
2. Connect the signal generator to EXT COUNT IN terminal.
3. Set the signal generator to 100mVrms, 200mHz and check the reading of 8210.
4. Vary the output frequency from 200mHz to 110MHz and check the 8210 displays
correct frequencies.
5. Push in LPF(Low Pass Filter) and check the LPF is working (-3dB +/-0.2dB point at
approx. 120kHz).
< Check procedure >
a. Apply 120KHz signal with minimum input level into EXT COUNT IN.
b. Push in LPF switch and check gate time(Frequency display) is stopped.
c. Increase input level and check the gate time(Frequency display) is starting to
and check the input level is increased about 3dB(+/-0.2dB) from “minimum input
level”.

2. ADJUSTMENT PROCEDURE

2-1. Preliminary Set-up

Remove top cover. Apply power, and allow at least 30 minutes for warm-up.

2-2. Power supply

a. Check the voltage in each position according to table 2-1.

Table 2-1 Power supply outputs

Check position Supplying Voltage Tolerance Remark
Output Pin of + 5 V ± 0.5V U6,15 : Assembled
U6,15,20 at Rear panel
Output Pin of U5 + 15 V ± 0.5V
Output Pin of U7 - 15 V ± 0.5V
Anode of ZD1 - 5 V ± 0.5V
Upper leg of R68 + 21 V ± 2 V

10
2-4. PRE-ADJUSTMENTS
EQUIPMENT
Oscilloscope
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
2-4-1. TRIANGLE WAVE OFFSET
1. Set this product as follows;
- Function ; TRIANGLE WAVE ( )
- ATT ; 20 dB(PUSH IN)
- AMPLITUDE ; MIN.
- FREQUENCY ; 10kHz
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
2. Set the oscilloscope to 0.5V/DIV, 20uS/DIV , DC Coupling and set the vertical
position to horizontal graticule center.
3. Connect the oscilloscope to output terminal.
4. Set “AMPLITUDE” control for 2DIV on CRT and adjust SFR15(OFFSET ADJUSTER) for “0
OFFSET of waveform”(The waveform should be in center. +/- 0.1DIV from horizontal
graticule center).

2-4-2.SQUARE WAVE LEVEL

1. Set this product as follows;
- Function ; “SQUARE WAVE ( )”
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; MAX.
- FREQUENCY ; 10kHz
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)

2. Change the function to “SQUARE WAVE”

3. Set the oscilloscope to 5V/DIV, 20uS/DIV
4. Check the output level of Square Wave is more than 17Vpp.

11
2-4-3.SINE WAVE LEVEL Adjust.

1. Set this product as follows;

- Function ; “SINE WAVE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; MAX.
- FREQUENCY ; 10kHz
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)

2. Change the function to “SINE WAVE”

3. Set the oscilloscope to 5V/DIV, 20uS/DIV
4. Adjust SFR10 , SFR13 for displaying “4DIV” on CRT. (SFR10 : + DIV from
horizontal graticule center for up-side of waveform , SFR13 : - DIV from
horizontal graticule center for down-side of waveform.

2-4-4. SINE WAVE DISTORTION ADJUST

EQUIPMENT
Distortion Analyzer
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)
PROCEDURE
1. Set this product as follows;
- Function ; SINE WAVE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; Max.
- FREQUENCY ; 10kHz
2. Connect Distortion analyzer to Output terminal.
3. Adjust SFR8, SFR11, SFR12 for minimum distortion reading on Distortion analyzer.
(less than 0.5 %)

12
2-4-5. AMPLITUDE CONTROL AND ATTENUATOR CHECK
EQUIPMENT
Oscilloscope
AC Millivoltmeter
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω

PROCEDURE
1. Set this product as follows ;
- Function ; SINE WAVE ( )
- ATT ; 0 dB(PULL OUT))
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the oscilloscope through FEEDTHROUGH TERMINATION 50 Ω
to output terminal.
3. Set Amplitude Control to Min. position and check the output level is lower than
1Vp-p(less 5div in 200mV/div).
4. Set Amplitude Control to Max. position and check the output level is higher than
10Vp-p(higher than 4div in 5V/div).
5. Set Amplitude Control to Min. position and connect AC Millivoltmeter to output
terminal.
6. Set the Range of AC millivoltmeter to 3V range and adjust Amplitude control for
0dB reading on AC millivoltmeter.
7. Push in “20dB ATT switch” and check the reading of AC Millivoltmeter is -20 dB.
8. Check the amplitude of TRIANGLE & SQUARE WAVE same as paragraph 3 to 7.

2-5. FREQUENCY RANGE ADJUSTMENT

EQUIPMENT
Frequency Counter
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω

PROCEDURE
1. Set this product as follows;
- Function ; TRIANGLE WAVE ( )
- ATT ; 20 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)

13
 - DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the Frequency Counter to Output Terminal.
2. Set Frequency Range to “1M” and Frequency Control(Dial) to MAX. Position.
3. Adjust SFR1 for 10.500 MHz frequency reading on counter.
4. Change Frequency Range to “100k” and adjust SFR2 for 1.0500 MHz frequency
reading on counter.
5. Change Frequency Range to “10k” and adjust SFR3 for 105.00 kHz frequency
reading on counter.
6. Change Frequency Range to “1k” and adjust SFR4 for 10.50 kHz frequency
reading on counter.
7. Change Frequency Range to “100” and adjust SFR5 for 1.050 kHz frequency
reading on counter.
8. Change the frequency range to 10 and 1, and check the frequency reading
in each range. (10 : 105.00 Hz , 1 : 10.500Hz)
9. After adjustment, check the frequency Control(Dial) at MIN. and MAX.
as following table.

8210 setting Tolerance

Range Frequency Control
1M MIN. Less than 100.0 kHz
MAX. Higher than 10.5 MHz
100k MIN. Less than 10.0 kHz
MAX. Higher than 1.05 MHz
10k MIN. Less than 1.0 kHz
MAX. Higher than 100.5 kHz
1k MIN. Less than 100 Hz
MAX. Higher than 10.5 kHz
100 MIN. Less than 10.0 Hz
MAX. Higher than 1.0 kHz
10 MIN. Less than 1 Hz
MAX. Higher than 100 Hz
1 MIN. Less than 100 mHz
MAX. Higher than 10 Hz

2-6. SYMMETRY ADJUST

EQUIPMENT
Oscilloscope
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
1. Set this product as follows;

14
 - Function ; SQUARE ( )
- ATT ; 0 dB(PULL OUT)
- AMPLITUDE ; CENTER
- COUNT ; INT(PULL OUT)
- DC OFFSET ; OFF(PUSH IN)
- SYM ; OFF(PUSH IN)
- SWEEP ; OFF(PUSH IN)
2. Connect the oscilloscope to output terminal.
3. Set the output frequency to 100kHz.
4. Pull out SYM Control and adjust to Min. position. And adjust SFR6 the
symmetry(duty ratio) is “lower than 1:10”.
5. Adjust SYM Control to Max. position and adjust SFR7 the symmetry(duty ratio)
is”higher than 10:1”.

2-7. FREQUENCY COUNTER ADJUST

EQUIPMENT
10MHz Standard Signal Source
Signal Generator up to 110MHz
BNC CABLE
FEEDTHROUGH TERMINATION 50 Ω (if necessary)

PROCEDURE
1. Set this product as follows;
- COUNT ; EXT(PUSH IN)
2. Connect 10MHz Standard Signal to the EXT COUNT IN terminal and adjust TC1 for
10.0000 MHz reading on Counter Display.
3. Set Signal generator to 110MHz, 100mVrms and connect the EXT COUNT IN terminal.
4. Adjust SFR16 (Shield Box IN) for 110.0000 MHz reading on Counter Display.
Reduce the output level of Signal Generator Slowly and adjust SFR16 for Minimum
input sensitivity(as possible as less than 100mVrms).
5. Change the out frequency of Signal Generator from 110MHz to 200mHz and check
the minimum input voltage is less than 100mVrms.

6. Push in LPF(Low Pass Filter) and check the LPF is working (-3dB +/-0.2dB point
at approx. 120kHz).
< Check procedure >
a. Apply 120KHz signal with minimum input level into EXT COUNT IN.
b. Push in LPF switch and check gate time(Frequency display) is stopped.
c. Increase input level and check the gate time(Frequency display) is starting to
and check the input level is increased about 3dB(+/-0.2dB) from “minimum input
level”.

15
3. Troubleshooting Procedure

3-1. Troubleshooting techniques

3-1-1. Check the function selector and switch setting. Incorrect switch settings can
give a false indication of instrument malfunction. If there is any question
about the correct function or operation, refer to OPERATOR'S MANUAL.

3-1-2. Check associated equipments before proceeding, ensure that any equipments used
with this product is operating correctly and verify that out and input signals
are properly connected and that the interconnecting cables are not defective.

3-1-3. Visual Check

Look for broken terminals, damaged components, mounting status of components,
damaged circuit boards, or other clues to the cause of a malfunction.

3-2. Troubleshooting procedure

3-2-1. NO Display
1. Check the “FUSE” and if it is broken, change to new one with same rating.
2. Check the output voltage of power transformer.
-. 17 to 18 Vac between pin 1 and 2 of CN14, and between pin 2 and 3 of CN14
on main board.
-. 8 to 10 Vac between pin 1 and 2 of CN4,CN24, and between pin 2 and 3 of
CN4,CN24 on main board.
3. Check the DC Power Voltage.
-. +5VDC at U6 and U15 output(U6,15 Assembled at rear panel)
4. Check the frequency at pin 19 of U12. It should be “10MHz”.
5. Check the connector cable from CN12’,CN13’(main board) to display board.

3-2-2. Triangle Wave Out-put

1. Check the Function switch operation and select Triangle Wave.
2. Check the DC Power Voltage for Generator Circuit.
-. +15VDC at U5 output
-. +5VDC at U6,U15,U20 output ( U6,15 :assembled at rear panel)
-. -5VDC at Anode of ZD1.
-. -15VDC at U7 output
-. +21VDC at upper leg of R68

3. Check the waveform at Q7 Emitter. The Triangle Wave should be appeared.

4. If not, check the operation of Amplifier and Triangle oscillator (U1 A/B/D, U2 A/B,

16
 Q1,Q2,Q3,Q4,Q5,Q6,D1,D2,D3,D5,Q7).
5. Check the Range Selector Switch operation and Frequency Control Volume and Cable
connection from VR1 to CN2(Main Board).
6. Check the “Amplitude VR4” and Cable connection from VR to CN5 on main board.
7. Check the waveform at R46. The Triangle Wave should be appeared.
8. If not, check the operation of Differential Amplifier(Q12,Q13,Q14,Q15,Q16).
9. Check the Attenuator switch(20 dB) and cable connection from CN7 to Output terminal.

3-2-3. Square Wave Out-put

1. Check the Function switch operation and select Square Wave.
2. Check the waveform at D1(of DD1) Cathode. The Triangle Wave should be appeared.
3. Check the waveform at D2(of DD1) Cathode. The Square Wave should be appeared.
4. If not, check the step 3-2-2. 4 and 5.
5. Check the waveform at 9pin of U3. The Square Wave should be appeared.
6. If not, check the operation of U3.
6. Check the waveform at R45. The Square Wave should be appeared.
7. If not, check the step 3-2-2. 8 and 9.

3-2-4. Sine Wave Out-put

1. Check the Function switch operation and select Sine Wave.
2. Check the waveform at Q7 Emitter. The Triangle Wave should be appeared.
3. If not, check the step 3-2-2. 4 and 5.
4. Check the waveform at Q11 Collector. The Sine Wave should be appeared.

5. If not, check the operation of Sine Shaper(Q8,Q9,Q10,Q11).

6. Check the waveform at R45. The Sine Wave should be appeared.
7. If not, check the step 3-2-2. 8 and 9.

3-2-5. TTL Output

1. Check the connection of cable for TTL Output terminal and Control Volume.
2. Check the waveform at Pin 9 of U3. The Square Wave should be appeared.
3. If not, check the step 3-2-3.
4. Check the waveform at pin 6 of U4. The TTL Level Square Wave should be appeared.
5. If not, check the operation of U4.

3-2-6. Sweep Operation(Width and Rate)

1. Check the cable connection(CN8,CN9) for Width and Rate Control Volume.
2. Vary the Width volumeand check the level of Pulse at pin 7 of U2 is varied.
3. Vary the Rate volume and check the period of Pulse at pin 14 of U2 is varied.
4. If not, check the operation of U2 C/D , D9 and Q17.

17
3-2-7. Frequency Range and Frequency Dial
1. Check the cable connection from CN2(Main Board) to Frequency Control Volume.
2. Check the operation of Range selector switch(Key Switch operation).

3-2-8. Attenuator(20dB)
1. Check the operation of each Attenuator switch.
2. If not working, check the R146,147,148

3-2-9. Frequency Counter(INT/EXT)

1. Check the INT/EXT selector switch operation and set to INT.
2. Check the output frequency at Output terminal by using Frequency counter and check
the frequency at R83 is same with output frequency.
3. Check the frequency of reference signal at pin18 and 19 of U12.
It should be “10.000MHz”.
4. If not, check Reference Oscillator(X1,T1,C54,).
5. Check the frequency at pin3 of U9 and pin 7of U18.
It should be same as output frequency.
6. If not, check the operation of Input Amplifier and Devider(Q18,Q19,U8,Q20,Q21,U18).
7. Check the cable connection between CN12(main board) and CN13(Display Board).
8. Check the operation of Counter Circuit, Micro-processor(U12), Driver(U4,5),
Scanner(U10,11)
9. Check the operation of Display Controller(U13,U14,Q22-28) on Display Board.

10. Check LPF function as follows;

a. Check the status of LPF S/W(push in)
b. Check the voltage at the left leg of R108. It should be around +5V.
c. Check the voltage at the anode of D16. It should be around 1.4-1.5V.
d. Check the voltage at cathode of D16. It should be around on 0.7-0.8V.

18
4. PARTS LIST
4-1.. Main PCB Parts List

Part Name Specification q"ty Referance.

CER.CAPACITOR 0.01uF50V(10nF) 2.00 C100,101

CER.CAPACITOR.SMD 3pF 1.00 C72

CER.CAPACITOR.SMD 15pF50V 1.00 C9

CER.CAPACITOR.SMD 22pF50V 1.00 C87

CER.CAPACITOR.SMD 30pF50V 2.00 C54,C84

CER.CAPACITOR.SMD 33pF50V 1.00 C82

CER.CAPACITOR.SMD 50pF50V 2.00 C01,C02

CER.CAPACITOR.SMD 0.01uF50V(10nF) 12.00 C2,8,15,29,31,33,34,39,45,47,90,91

CER.CAPACITOR.SMD 0.1uF50V(100nF) 25.00 C17-19,49-53,56,59,61,67-71,74-76,78,80,81,94,202

CER.CAPACITOR.SMD 130pF50V 3.00 C10,38,41

CER.CAPACITOR.SMD 150pF50V 2.00 C13,66

CER.CAPACITOR.SMD 1.5pF50V 1.00 C73

CER.CAPACITOR.SMD 470pF50V 1.00 C44

CER.CAPACITOR.SMD 4700pF50V(4.7nF) 2.00 C85,86

TRIMMER CAPACITOR CTC05F500,50pF/2READ 1.00 T1

MICA CAPACITOR 33pF/63V 1.00 C3

MICA CAPACITOR 680pF/63V 1.00 C4

M/F.CAPACITOR 0.47uF250V 1.00 C37

M/F CAPACITOR(BOX) 0.0068uF/63V(6.8nF) 1.00 C5

M/F CAPACITOR(BOX) 0.068uF/63V(68nF) 1.00 C6

M/F CAPACITOR(BOX) 0.68uF63V(680nF) 1.00 C7

MYLER CAPACITOR 0.22uF100V(220nF) 1.00 C36

ELEC.CAPACITOR 10uF35V 1.00 C55

ELEC.CAPACITOR 22uF16V 10.00 C1,12,14,22,23,25,28,30,32,35

ELEC.CAPACITOR 47uF35V 6.00 C27,40,42,43,46,48

ELEC.CAPACITOR 100uF25V 2.00 C77,79

ELEC.CAPACITOR 1000uF35V 2.00 C21,24

ELEC.CAPACITOR 220uF35V 1.00 C20

ELEC.CAPACITOR 2200uF35V 1.00 C58

ELEC.CAPACITOR 470uF25V 3.00 C60,200,201

SWITCHING DIODE.SMD 1N4148 13.00 D3-11,14,15,16,17

SWITCHING DIODE.SMD HSMS-2825-TR1 1.00 D1-1

19
 Part Name Specification q"ty Referance.

C/F. RESISTOR.SMD 22J, 1/8W 3.00 28,47,102

C/F. RESISTOR.SMD 220J, 1/8W 3.00 4,29,118

C/F. RESISTOR.SMD 2.2KJ, 1/8W 4.00 9,10,90,91

C/F. RESISTOR.SMD 22KJ, 1/8W 1.00 89

C/F. RESISTOR.SMD 240J, 1/8W 1.00 147

C/F. RESISTOR.SMD 270J, 1/8W 1.00 41

C/F. RESISTOR.SMD 2.7KJ, 1/8W 1.00 11

C/F. RESISTOR.SMD 300J, 1/8W 1.00 39

C/F. RESISTOR.SMD 33J, 1/8W 3.00 27,72,170

C/F. RESISTOR.SMD 330J, 1/8W 4.00 34,95,98,99

C/F. RESISTOR.SMD 33KJ, 1/8W 1.00 40

C/F. RESISTOR.SMD 39KJ, 1/8W 1.00 71

C/F. RESISTOR.SMD 470J, 1/8W 7.00 93,94,96,97,100,101,108

C/F. RESISTOR.SMD 4.7KJ, 1/8W 1.00 30

C/F. RESISTOR.SMD 51J, 1/8W 1.00 114

C/F. RESISTOR.SMD 510J, 1/8W 4.00 86,87,R01,R02

C/F. RESISTOR.SMD 5.1KJ, 1/8W 3.00 74,75,76

C/F. RESISTOR.SMD 62J, 1/8W 2.00 146,148

C/F. RESISTOR.SMD 7.5KJ, 1/8W 2.00 7,73

C/F. RESISTOR.SMD 8.2KJ, 1/8W 1.00 104

SEMI-FIXED RESISTOR VZ067TH1, 100B 1.00 SFR11

SEMI-FIXED RESISTOR VZ067TH1, 1KB 2.00 SFR10,13

SEMI-FIXED RESISTOR VZ067TH1, 10KB 8.00 SFR1,2,3,4,5,6,7,16

SEMI-FIXED RESISTOR VZ067TH1, 100KB 2.00 SFR12,15

SEMI-FIXED RESISTOR VZ067TH1, 2KB 1.00 SFR8

M/F. RESISTOR.SMD 1KF, 1/8W 4.00 21,35,37,38

M/F. RESISTOR.SMD 100KF, 1/8W 1.00 117

M/F. RESISTOR.SMD 11KF, 1/8W 2.00 23,25

M/F. RESISTOR.SMD 120F, 1/8W 1.00 136

M/F. RESISTOR.SMD 1.21KF, 1/8W 2.00 12,16 (1.2K,F)

M/F. RESISTOR.SMD 121KF,1/8W 2.00 R13,17

M/F. RESISTOR.SMD 1.5KF, 1/8W 1.00 133

M/F. RESISTOR.SMD 21.5F, 1/8W 2.00 137,139 (22,F)

M/F. RESISTOR,SMD 2.2KF, 1/8W 1.00 135

M/F. RESISTOR.SMD 249F, 1/8W 1.00 R115 (243,F)

20
 Part Name Specification q"ty Referance.

M/F. RESISTOR.SMD 24.9KF, 1/8W 1.00 129 (24.3K,F)

M/F. RESISTOR.SMD 3.32KF, 1/8W 1.00 119 (3.4K,F)

M/F. RESISTOR.SMD 42.2F, 1/8W 1.00 120

M/F. RESISTOR.SMD 430F, 1/8W 2.00 22,24

M/F. RESISTOR.SMD 4.99KF, 1/8W 1.00 132

M/F. RESISTOR.SMD 56.2F, 1/8W 1.00 138 (56,F)

M/F. RESISTOR.SMD 576F, 1/8W 1.00 121

M/F. RESISTOR.SMD 825 1/8W F 2.00 127,130

M/F. RESISTOR 900F, 1/4W 1.00 32

OXIDE FILM RESISTOR 560J, 1W 1.00 66

KEY SWITCH SPUN90X1CO21 1.00

KEY SWITCH SPUN40X1C041 1.00

POWER SWITCH JPP2295MPACS72 1.00 P-S/W1

I.C.(TI) SN75107AN 1.00 U3

I.C.SMD BA10324AF 2.00 U1,2 Rohm

I.C.(SAM.MOTO.NS.) MC7805 1.00 U20

I.C.(SAM.MOTO) MC7815 1.00 U5

I.C.(SAM.MOTO) MC7915 1.00 U7

I.C.(MOTO.) MC10116 1.00 U8

I.C.(HAR.RCA) CA3096AE 1.00 U17

I.C.SMD(SIG) SN7400/SN74S00 1.00 U4

I.C(NS) 74F191N 1.00 U18

I.C.SMD(NS.HIT.PHI.) SN74HC393 2.00 U10,11

I.C.SMD(NS.HIT.SGS.) SN74HC138 1.00 U14

I.C.(TOSHIBA) TD62783AP 1.00 U13

I.C.(AMD) GAL16V8 1.00 U9

WIRE ASS'Y(1365#30) IN PUT CABLE,250mm 1.00

CRYSTAL 10.0000MHz(HC-49/U) 1.00 10M 20PPM .

MAIN PCB 8210-M12 1.00

SHIELD CASE Zn-pl 0.3t 104x40x18 1.00

NUT M3, NI-PL 1.00 U15 Ass'y

SCREW, MACHINE M3x8BH, NI-PL 1.00 U15 Ass'y

SCREW, TAPPING T3x6BH,ZN-PL 3.00 U37,15,20

SPRING, COIL 6x2x7(SHIELD 용) 0.00 MAIN PCB GND

HEAT SINK TR 용,내경 8.3,외경 16 2.00 Q16,29 Ass'y

HEAT SINK 78SERIES 용(ㄷ자모양) 2.00 U7,15 Assy'

HEAT SINK 8210 ㄷ자 17x9x19 1.00 U20 Ass'y

21
4-2.. Display PCB Parts List
Part Name Specification Q'ty Referance

WAFER 8pin,YW02508,연호 2.00 CN12,13

FND(hp) HDSP-H513#001 1.00 FND(SINGLE )

FND(hp) HDSP-K513#001 3.00 FND1,2,3

LED BL-R2130A-T(5x5X10) 5.00 LED 1-5

DISPLAY PCB(80SER.) 8210-DIS-01 1.00

4-3.. VR PCB Parts List

Part Name Specification Q'ty Referance

WAFER 3pin,YW02503,연호 5.00 CN8(WIDTH),CN9(RATE),CN2(FREQ),CN5(AMP),CN6(OFFSET)

WAFER 4pin,YW02504,연호 1.00 CN3(SYM)

VARIABLE RESISTOR V16L4(7x5)S15KCB10K 1.00 VR5(WIDTH),

VARIABLE RESISTOR V16L4(7x5)S15KCB5K 1.00 VR4(OFFSET)

VARIABLE RESISTOR V16L4(7x5)S15KCB50K 1.00 VR2(SYM)

VARIABLE RESISTOR V16L4N15KCB10K 2.00 VR6(RATE),VR1(FREQ),

VARIABLE RESISTOR V16L4N15KCB500 1.00 VR3(AMP)

VR PCB(80SER.) 8210-VR-02 1.00

4-4. Front Panel Assembly Parts.

Part Name Specification Q'ty Referance

BNC CONNECTOR BNC-RB-4CUTTING 4.00 OUTPUT,TTL SYNC, VCF, EXT COUNTER IN

WIRE ASS'Y( ) 2pin 150mm 1.00 VCF

WIRE ASS'Y( ) 2pin 220mm 2.00 TTL.OUTPUT

BRACKET, VR PCB BN-LGP,160x25x30 1.00

BRACKET, BNC BN(80SER.)-AG/FG 1.00

FRONT PANEL, ABS BN(80SER-난연)-12965 1.00

KNOB, VR, ABS Pi10x13mm,DARK-GRAY 6.00

PLATE, FRONT, PC 8210DAG 1.00

ACRYLE FILTER 8210-DAG 1.00

NUT(VR) 6.00 VR

NUT(BNC,F) 4.00 BNC BRACKET

NUT M3, NI-PL 2.00 BNC BRACKET

SCREW, MACHINE M3x4BH,NI-PL 2.00 BNC BRACKET

SCREW, TAPPING T3x8BH, ZN-PL 5.00 VR PCB

WASHER, PLAIN 내경:3,외경:12/NI-PL 2.00 EXT COUNT IN BNC

WASHER,PLAIN(VR) 7.2x12x0.2t/NI-PL 6.00 VR

WASHER,LATCH(BNC) 9.5x13x0.5t/NI-PL 4.00 BNC

WASHER,PLAIN(BNC S.) 10x13x0.3t/NI-PL 4.00 BNC

DISPLAY PCB ASS'Y FG-8210/DAGA 1.00

VR PCB ASS'Y FG-8210/DAGA 1.00

22
4-5. Rear Panel Assembly Parts.

Part Name Specification Q'ty Referance

FUSE(UL,VDE) 50F,250V200mA(20mm) 1.00 FUSE HOLDER IN

FUSE HOLDER R3-11,BN 1.00 REAR PANEL ASS'Y

EMI GASKET 71TS-FK10-R10-170-00 1.00 REAR PANEL ASS'Y

MOTOR FAN DC5V,0.5W (40x40) 1.00 REAR PANEL ASS'Y

GND CONNECTOR 1.00 REAR PANEL ASS'Y

AC INLET(SAM IL) NFU-101,NOISE FILTER 1.00 REAR PANEL ASS'Y

POWER TRANS FG-8210,8220 1.00 REAR PANEL ASS'Y

I.C.(SAM.MOTO.NS.) MC7805 2.00 REAR PANEL ASS'Y (U5,U15)

HEAT TUBE Pi5 x 15 mm 3.00 AC INLET,FUSE HOLDER

HEAT TUBE Pi 12 x 60 mm 1.00 FUSE HOLDER

WIRE ASS'Y(1015#22) GND WIRE,180mm,LUG 3.00 REAR PANEL ASS'Y

WIRE ASS'Y(1015#22) DIW,120mm,BLACK 1.00 AC IN-FUSE

WIRE ASS'Y(1015#22) 3pin 2Wire ,220mm 1.00

BRACKET, POWER

TRANS BN-DAG, 27x10.5,2T 2.00 TRANS

REAR PANEL PRESS BN-DAG,FG-8210 1.00

NUT(GND TERMINAL) INCH 2.00 GND CONNECTOR

NUT M3, NI-PL 8.00 TRANS,REGULATOR, FAN

SCREW, MACHINE M3x10BH,흑착색 2.00 NOISE FILTER (AC INLET)

SCREW,MACHINE M3x16BH 흑착색 2.00 FAN

SCREW, MACHINE M3x8BH-W, NI-PL 2.00 TRANS

WASHER, PLAIN 내경:3,외경:10/NI-PL 4.00 TRANS,AC INLET

WASHER, SPRING 내경:3,외경:5, ZN-PL 2.00 TRANS

WASHER, LATCH 4x6.5x0.3t 1.00 GND CONNECTOR

23
4-6. Others.

Part Name Specification Q'ty Referance

I.C.(ATMEL) AT89C52 1.00 U12

CABLE TIE 100mm, WHITE 10.00

WIRE ASS'Y(#24) 3-3pin 150mm 6.00

WIRE ASS'Y(#24) 4-4pin 150mm 1.00

WIRE ASS'Y( ) 8-8pin 220mm 2.00

WIRE ASS'Y( ) 3-3pin 150mm 1.00

SHIELD CASE 8210 TOP 0.6t 210x202(156)x35 1.00 MOUNT POLE- TOP

SHIELD CASE 8K-BOT Znpl 0.6t 210x202x35 1.00 MONUT POLE-BOTTOM

BOTTOM CASE, ABS BN(80SER,난연)-12965 1.00

TOP CASE, ABS BN(80SER.난연)-12965 1.00

HANDLE, ABS BN(80SER.난연)-12965 1.00

RUBBER FOOT BN-DAG,37x8.5,대 2.00 BOTTOM CASE

RUBBER FOOT BN-DAG,32x8.5,소 2.00 TOP CASE

EMI GASKET 71TS-FK10-R10-170-00 1.00 BOTTOM SHIELD CASE ASS'Y

SHIELD PLATE BN-DAG, 248X163 0.00 SHIELD CASE BOTTOM

SPONGE PAD 20x40,5T,한쪽 테이프 6.00 MAIN PCB AC LINE PART

KNOB, POWER, ABS BN-DAG(80SER.) 1.00 POWER STICK

KNOB, PUSH S/W, ABS BN(80SER.)-12965 13.00 KEY S/W

SCREW, MACHINE M3x6BH,H5, NI-PL 0.00 SHIELD TOP + MOUNT POLE

SCREW, MACHINE M4x45BH, ZN-PL 4.00 TOP+BOTTOM CASE

SCREW, TAPPING T3x8BH, H6, NI-PL 3.00 PCB -BOTTOM CASE

MOUNTING POLE Pi3x50,육각 8210MAIN 1.00 MAIN PCB-SHIELD CASE

WASHER, SPRING 내경:3,외경:5, ZN-PL 1.00 SHIELD TOP + MOUNT POLE

EMI AIR VENT FILTER SUI40-24-125-45-13 2.00 TOP,BOTTOM SHIELD

FRONT PANEL ASS'Y FG-8210/DAGA 1.00

REAR PANEL ASS'Y FG-8210/DAGA 1.00

MAIN PCB ASS'Y FG-8210/DAGA 1.00

24
4-7. Packing

Part Name Specification Q'ty Referance

FUSE(UL,VDE) 50F,250V200mA(20mm) 1.00 SPARE FUSE.

POWER CORD(230V) KKP-30,SVT3/18A"VDE" 1.00 "VDE"

CABLE ASS'Y( ) BNC TO CLIP( ) 1.00

STYROFOAM BOX BENCH, 300x150x65mm 2.00

SILICA GEL 3g 1.00

STICKER, S/N, 230V BN(80SER.),15W200mA 1.00 15w ,230V/200mA F

MANUAL(8210) FG8210, DAG 영문 1.00

INNER BOX (8000SER.) DAG-BN,340x310x165 1.00

CARTON BOX(무인쇄) BN,645x355x365 0.25 4CTN.(IN BOX -340x310x165)

VINYLE BAG 70x100mm,Zipper Type 1.00 SPARE FUSE.

VINYLE BAG 265x400mm 1.00 PRODUCT.

5. CIRCUIT DIAGRAM
- Refer to Attached File.

25
 5 4 3 2 1

R83
10K
COUNTER
+5V(A)
D D
06-R150#1
+
C40
47/16V C39 R87 C48 + C47
+5VD 103 510 47/16V 103

C44 R95
470P(C/C) 330 R99
330
R85 Q20
BNC4 100K R88 U8A 2N3906 R102

1/16
EXT COUNT IN Q18 150 U8B R92 MC10116 U8C 22

1
2N5486 C9 MC10116 150 2 MC10116
1 3 47/16V 7 4 15
10 13
C37

+
5
474/250V
2

2
9 3 12
SW5 C38 6 14 Q21
EXT/INT SW 130P C41 2N3906

11
130P

8
Q19 R93 R94 R96 R97 R98
C D10 D11 2N3906 470 470 470 470 330 R103 C

3
1N4148 1N4148 R100 R101 120
R86 R89 470 470
510 22K
SFR16 2
10K
R90 R91
+ 2.2K 2.2K
C43

1
47/16V
15 A QA 3
R108 D16 C91 + C46 C45 1 2
470 1N4148 103 47/16 103 B QB
10 C QC 6
9 D QD 7
RCO 13
14 CLK
+5VD 4
C90 D17 G
5 D/U
103 1N4148 11
SW6 LOAD
MX/MN 12
L.P.F
C12 U18
103 74LS191

B 06-U9#3 B
06-U9#5
06-U9#4

R01 C01 R02 C02

510 50P 510 50P

Title 8210 - 05 Drawing Design Checked Approved

Model COUNTER PREAMP CIRCUIT

Size A3 Rev 02
Sheet 5 of 6 Scale 2:1

A
Date 2002/04/13 DAGATRON A

5 4 3 2 1
 5 4 3 2 1

/Sa mHZ D1

/Sb HZ D2
D D

/Sg
/Sa
/Sb

/Sa
/Sb

/Sg
/Sa
/Sb

/Sa
/Sb

/Sg
/Sa
/Sb

/Sa
/Sb

/Sg
/Sa
/Sb
/F3
/F4

/F5
/F6

/F7
/F8

/F9
/Sf

/Sf

/Sf

/Sf

/Sf

/Sf

/Sf
/Sc KHZ D3

1
2
3
4
5
6
7
8
9

1
2
3
4
5
6
7
8
9

1
2
3
4
5
6
7
8
9

1
2
3
4
5
/Sd MHZ D4
FND1 FND2 FND3 FND4
SEGMENT SEGMENT SEGMENT SEGMENT /Se G.T D5

+5V(D)
8.8. 8.8. 8.8. 8.

18
17
16
15
14
13
12
11
10

18
17
16
15
14
13
12
11
10

18
17
16
15
14
13
12
11
10

10
C49 C50 C51 C52 C56 C53

9
8
7
6
104 104 104 104 104 104

/Se
/Sd

/Sh
/Se
/Sd
/Sg

/Sh

/Se
/Sd

/Sh
/Se
/Sd
/Sg

/Sh

/Se
/Sd

/Sh
/Se
/Sd
/Sg

/Sh

/Se
/Sd

/Sh
/Se
/Sc

/Sc

/Sc

/Sc

/Sc

/Sc

/Sc
/F3
/F4
/F5
/F6
/F7
/F8
/F9
U9
PAL16R4 J13

8
7
6
5
4
3
2
1
C 12 F0 I0 1 CN13 C
13 F1 I1 2
14 3 J13'
F2 I2 05-U18#14
15 4 CN13'
F3 I3 05-U18#7

1
2
3
4
5
6
7
8
16 F4 I4 5 05-U18#6
17 6 U13 J3 J3'
F5 I5 TB62783 CN3 CN3'

1
2
3
4
5
6
7
8
18 F6 I6 7
19 8 1 18 1 /Sa
F7 I7 I0 O1 1 1

/CO0
/CO1
/CO2
/CO3
/CO4
/CO5
/CO6
/CO7
9 2 17 2 /Sb
I8 I1 O2 2 2 /Sc
I9 11 3 I2 O3 16 3 3 3
4 15 4 /Sd
I3 O4 4 4 /Se
5 I4 O5 14 5 5 5

/CO0

/CO1

/CO2

/CO3

/CO4

/CO5

/CO6

/CO7
6 13 6 /Sf
I5 O6 6 6 /Sg
7 I6 O7 12 7 7 7
U12 8 11 8 /Sh Q22 Q23 Q24 Q25 Q26 Q27 Q28 Q32
89C52 I7 O8 8 8 A1015 A1015 A1015 A1015 A1015 A1015 A1015 A1015
U10A
74LS393 16 WR /a
1 A QA 3 17 RD P1.0 1
4 13 2 /b R105 R106 R107 R108 R109 R110 R111 R112
QB INT1 P1.1 /c 10 10 10 10 10 10 10 10
QC 5 P1.2 3
2 6 21 4 /d
CLR QD P2.0 P1.3

/CM0

/CM1

/CM2

/CM3

/CM4

/CM5

/CM6

/CM7
22 5 /e
U10B P2.1 P1.4 /f
23 P2.2 P1.5 6
B 74LS393 24 P2.3 P1.6 7 /g
/h U14
B
13 A QA 11 25 P2.4 P1.7 8
10 26 74LS138
QB P2.5 /CM0 +5V(D)
QC 9 27 P2.6 RXD 10 1 A Y0 15
12 8 15 11 2 14 /CM1
CLR QD T1 TXD B Y1 /CM2
INT0 12 3 C Y2 13
U11A 28 12 /CM3 R149
74LS393 P2.7 +5V(D) +5V(D) Y3 /CM4 10
14 T0 Y4 11
1 3 6 10 /CM5
A QA G1 Y5 /CM6
QB 4 39 P0.0 EA/VP 31 4 G2A Y6 9
5 38 9 5 7 /CM7
QC P0.1 RESET + C55 G2B Y7 Q30
2 CLR QD 6 37 P0.2 X1 19 05-SW5#5
36 10/16V C1815
U11B P0.3 Y1 R150
35 P0.4
74LS393 34 10MHZ 1K
P0.5
ALE/P
PSEN

13 A QA 11 33 P0.6
QB 10 32 P0.7 X2 18
9 R104
QC 8.2K
12 8
29
30

CLR QD T1
C64 C57 20P
30P 56P
Title 8210 - 06 Drawing Design Checked Approved

Model CPU CONTROL CIRCLE

A Size A3 Rev 02 A
Sheet 6 of 6 Scale 2:1

Date 2002/04/13 DAGATRON

5 4 3 2 1
 5 4 3 2 1
D8
1N4148

J8

3
SW1 CN8 R70 +15V +15V
SWEEP WIDTH 1K
1
3 2
Sweep Width VR5 2 1 3

1
10KB 8
D 2 D
SFR8

1
2.2KB
-15V
+15V
C36

3
R73 0.22uF(MYLER)
7.5K R75 C31 + C30

3
J9 5.1K 0.01(C/C) 22/16V R11
CN9 R71 2.7K
39K R74
VR6 1 5.1K R76
Sweep Rate 2 2 9 -
02-U30A#12

4
10KB 8 13 - 5.1K
3 Q17
10 + 14 5 +
U2C 12 + 2N3906 7 Q2
GL324 U2D 2N3904
1

6 -
R72 GL324 U2B
33 GL324

11
D9 R77
1N4148 10K
+
C33 C32
C 0.01(C/C) 22/16V C
-15V

BNC1 J1 R300 R2 R4
VCF IN CN1 470 1K 220
1 1

3
2
C304 R1 R9
2

104 10K 2.2K SFR6 2

10KB

R3
1K

1
5 +
7 2 -
3

J2 6 1 Q1
-
CN2 U1B 3 + 2N3906
GL324 U1A
VR1 1 GL324
Frequency 10KB
2 2 R8 R10
3 1K 2.2K

R114
1

B 51
SFR1 +21V
B
2

10KB

3
3 1

C29 + C28 -15V

SFR2 0.01(C/C) 22/25V J3 SFR7 2
2

10KB CN3 10KB

3 1 4
4 3

1
2

3
SFR3 10 + 1
2

10KB 8
3 1 9 - 02-U30B#3
U1C 2 VR2
+15V GL324 50KB
11

SFR4
2

10KB

1
3 1

R6
1K SFR5
2

10KB 3
3 1 1
A R7
C2
0.22uF 22/16
8 Title 8210 - 01 Drawing Design Checked Approved A
+
7.5K C37 SW2
Symm
Model FREQ/VCF IN CIRCUIT
-5V
Size A3 Rev 02
Sheet 1 of 6 Scale 2:1

Date 2002/3/30 DAGATRON

5 4 3 2 1
 5 4 3 2 1

02-R19#1 +15V
02-U4A#1
02-R32#1

C76
R126 0.1(MON)
D +5V R46 C19 100 R138 D
2K 0.1(MON) R124 C67 56.2F R140 D5

3
1K 0.1(MON) 10(1/2W) 1N4148
R117 U17
R69 100KF CA3096 C78
10 2 1 16 R125 0.1(MON)
Q1B SUB 1K R127 C75
2 Q1E
SFR15 R118 3 15 825F 0.1(MON) + C77
100K 220 Q1C Q5C 100/25V
Q5B 14

1
4 Q2E Q5E 13
C35 C34 5 R139
22/16V + 0.01 SW1 SW2 SW3 Q2B 21.5F
6 Q2C Q4C 12
SINE TRIANGLE SQUARE 11 R128 Q14
Q4B 150 2N3563
7 Q3E Q4E 10
R119 8 Q15
3.32KF Q3B 2N3906
Q3C 9
R120 R121 Q16
42.2F 576 2N2219
R147
2

240
3 1 D6
C17 C66 C71 1N4148
SFR10 0.1(MON) 150P R132 0.1(MON) R146 R148
1KB 4.99KF 62 62
C R37 C
1KF C68
R33 C87 0.1(MON)
2K 22P R135 R141
Q10 10(1/2W) 10(1/2W)
C3198 R129
24.9KF R144
100(1/2W)
R41 BNC3
270 R115 R134 R136 6 1 OUTPUT
R42 249 1.5KF 2.2KF
1

R40 220 5 2 1
33K
Q8 Q9 2 Q11 4 3

2
C1815 C3198 C3198 R122

2
1.1K SW3
3

SFR12 J5 C72 C73 R145 ATT

100KB CN5 1.5pF 1.5pF R142 100(1/2W) C82 RG58
+15V C69 10(1/2W) 100P
3

1
3
2

2 2 0.1(MON) D7
3 1 R43 1 R123 1N4148
R34 R42 1K C18 1.21K Q29
330 SFR11 1K 0.1(MON) 2N2905
100B R116 R47 R160 Q13
1

B R35 R38
VR3
AMP 500B
10K 22 1K
Q12
2N3904 B
3

1KF 1KF 2N5771 D14

C80 1N4148
R130 C74 0.1(MON)
2 J6 825F 0.1(MON)
3

CN6 100/25V
+
SFR13 SW4 3 C79
1KB DC OFFSET 2
R36 R137 R136
1

2 1 2 1
1K 21.5F 144F R74
R131 C70 10(1/2W)
R161 100 0.1(MON)
VR4 1K C81
1

5K 0.1(MON)

R44 -15V
C14 + 10 C15
22/10V 0.01uF(CER)

A
Title
8210 - 03 Drawing Design Checked Approved
A
Model AMPLFIER CIRCUIT
-5V
Size A3 Rev 02
Sheet 3 of 6 Scale 2:1

Date 2002/04/13 DAGATRON

5 4 3 2 1
 5 4 3 2 1

+21V

+21V
R68
D 10/0.5W + C20 D
2200/35V
+15V

DB1
+15V

1
J14' J14 DB06M
CN14' CN14 U5 U6 +5V
7815 7805
1 1
2 2 2 - + 4 1 VIN VOUT 3 1 VIN VOUT 3 +5V

GND

GND
3 3
+ C21 + C22 + C23
1000/35V 22/16V 22/16V

2
U7
7915
2 VIN VOUT 3 -15V

GND
C25
+ +
C24 22/16V
C 1000/35V -15V C

1
R66
560/1W

-5V

ZD1 +
5.1V C27
47/35V -5V

+5V(D)
T2
TRANSFORMER POWER
D12 U15
11 1 J4' J4 1N4003 7805
2 CN4' CN4 1 3
VIN VOUT +5V(D)
SW8 ST1 J16' J16 3

GND
F1 F2 J15' J15 POWER S/W SELECT CN16' CN16 1 1
2 2
B NOISE FILTER FUSE CN15' CN15
1 1 4 3 3
C59
104
+ C58
2200/16V
+ C60
470/16V
C61
104
B
1 1 1 1 3 2 2 5

2
3 2 2 3 3 6
2 2 4 D13
3 3 1N4003
7
8
10 9
FAN
D20 U20 J17 DC FAN
C306 C307 J5' J5 1N4003 7805 CN17
104/1KV 104/1KV CN5' CN5 1 3 1 2
VIN VOUT 1

GND
1 1 2
2 2 C201 +
3 3 + C200 470/16V C203
C202 470/16V 104

2
D22 104
1N4003

Title 8210 - 04 Drawing Design Checked Approved

Model POWER SUPPLY CIRCUIT

A A
Size A3 Rev 02
Sheet 4 of 6 Scale 2:1

Date 2002/04/13 DAGATRON

5 4 3 2 1
 5 4 3 2 1

+15V

D D
R12 R13 +5V
1.2KF 120KF L2
INDUCTOR AUDIO

C100 C305 + C12

R26 10n 10n 100/10V
1K
D1-2 +5V
HSMS2825

L1
INDUCTOR AUDIO

1
R14 Q3
13 - 10K 5771 3 Q5
14 2N5486
12 + C3
01-R11#1
U30D 33P C101

2
072 R23 10n(C/C)
C4 11KF

14
680P(BOX) D3
C85 1N4148 4 BNC2
472 C5 6 R27 J10 R170 OUTPUT
C 6.8n(BOX) 5 33 CN10 33 C
R24

14
1 1

6
8
D1-1 C6 C8 430F U4B
HSMS2825 68n(BOX) D4 0.01(C/C) 74LS00 R28 C13 2

S
2G
VCC+
1N4148 22 150P TTL SYNC OUT

2
11 2B 2Y 9
12 2A
Q7 C10
2N3563 130P
C86 2 R30 R29
472 1B 4.7K 4.7K
1 1A 1Y 4
R001 C84 U4

VCC-
Q4 ??? C7 30P(C/C) SN75107

1G
3 3563 0.68n(BOX)
01-CN3#1 +
1 R20 R21 1

13
1
1K 1KF

5
2 - 3
U30A R15 3 Q6 2
072 10K 2N5486
L3 U4A
INDUCTOR AUDIO 74LS00

2
R31
240

B R24
R25
11KF R32
B
430 -5V 2.2K
R18 R19 C9
10 1.5K 15P(C/C)
R17
R16 120KF
1.2KF

03-SW3#6

03-SW3#2

03-R46#1

Shield Box

A
Title
8210 - 02 Drawing Design Checked Approved
A
Model OSCILLATOR/TTL CIRCUIT
Size A3 Rev 02
Sheet 2 of 6 Scale 2:1

Date 2002/3/30 DAGATRON

5 4 3 2 1