Sun 310-044

SUN CERTIFIED NETWORK ADMINISTRATOR FOR SOLARIS 9

Version 1.0
QUESTION NO: 1

Which two tasks involve changes to the dhcptab database? (Choose two.)

A. defining an additional symbol

B. changing a client macro association so that the client uses a different macro

C. updating the pool of IP addresses assigned to clients

D. tuning the IGNORE_FAILED_ARP parameter

E. changing the definition of a macro

Answer: A,E

QUESTION NO: 2

You have used the appropriate startup script in /etc/init.d to start the NTP daemon. However, the NTP
daemon does not start up. There is no error message. What is the reason for this?

A. There is no configuration file.

B. rpcbind is not running on the machine.

C. The configuration file contains faulty entries.

D. The NTP daemon cannot contact an NTP server.

Answer: A
QUESTION NO: 3

Which two statements about a Layer 2 switch are true? (Choose two.)

A. A switch can connect more than one pair of cable segments simultaneously.

B. A switch can convert between two different protocol suites.

C. A switch can dynamically connect and disconnect two cable segments without operator intervention.

D. A switch can filter and selectively forward a packet based on the IP address in the packet.

Answer: A,C

QUESTION NO: 4

In which mode is an Ethernet card configured to pass all Ethernet frames up the protocol stack
(inbound) regardless of the Ethernet frame's destination MAC address?

A. Point-to-Point

B. Promiscuous Mode

C. Profligate Mode

D. Prominent Mode

E. PointCard Mode

Answer: B

QUESTION NO: 5 DRAG DROP

Click the Task button.

When investigating tunneling, you decide to use snoop to examine the way header and encapsulation
works. You ping the destination address of the tunnel and get a successful reply. In the snoop output
you discover these protocols:

ICMPv6

ETHER

IPv6

IPv4

Place the protocol types in the order of encapsulation in which they would be observed in the snoop
output.

Note: Box 1 should contain the outermost protocol in terms of encapsulation, and Box 4 should contain
the innermost encapsulated protocol.

Answer: <m x1="9" x2="79" y1="31" y2="77" ss="0" a="0"></m><m x1="88" x2="160" y1="29" y2="76"
ss="0" a="1"></m><m x1="169" x2="239" y1="31" y2="77" ss="0" a="2"></m><m x1="249" x2="319"
y1="30" y2="77" ss="0" a="3"></m><m x1="7" x2="80" y1="134" y2="183" ss="1" a="0"></m><m
x1="90" x2="158" y1="134" y2="184" ss="1" a="1"></m><m x1="168" x2="238" y1="134" y2="183"
ss="1" a="2"></m><m x1="250" x2="320" y1="133" y2="183" ss="1" a="3"></m><c start="1"
stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c start="2" stop="3"></c>
QUESTION NO: 6

Which interface flag is monitored by in.mpathd to detect whether an interface failure has occurred?

A. MULTICAST

B. DEPRECATED

C. RUNNING

D. NOFAILOVER

Answer: C

QUESTION NO: 7

Which is an example of a standard DHCP option?

A. SinstNM

B. sun4u

C. SUNW.Ultra-30

D. TFTPsrvN

Answer: D

QUESTION NO: 8 DRAG DROP

Click the Task button.

Place each action on the corresponding file that is modified as a result of the action.

Answer: <m x1="10" x2="115" y1="221" y2="253" ss="0" a="0"></m><m x1="124" x2="227" y1="222"
y2="254" ss="0" a="1"></m><m x1="235" x2="341" y1="221" y2="255" ss="0" a="2"></m><m x1="85"
x2="85" y1="239" y2="239" ss="0" a="3"></m><m x1="37" x2="140" y1="62" y2="95" ss="1"
a="0"></m><m x1="36" x2="141" y1="100" y2="132" ss="1" a="1"></m><m x1="38" x2="141" y1="141"
y2="171" ss="1" a="2"></m><c start="0" stop="1"></c><c start="1" stop="2"></c><c start="2"
stop="0"></c>

QUESTION NO: 9 CORRECT TEXT

What is the full path name of the NTP server configuration template file? Answer:

Answer: /ETC/INET/NTP.SERVER
QUESTION NO: 10 DRAG DROP

Click the Task button.

Place each network component on the TCP/IP model layer at which it operates.

Answer: <m x1="35" x2="162" y1="48" y2="96" ss="0" a="0"></m><m x1="36" x2="165" y1="105"
y2="152" ss="0" a="1"></m><m x1="37" x2="161" y1="159" y2="206" ss="0" a="2"></m><m x1="38"
x2="166" y1="215" y2="263" ss="0" a="3"></m><m x1="228" x2="357" y1="47" y2="97" ss="1"
a="0"></m><m x1="227" x2="354" y1="103" y2="152" ss="1" a="1"></m><m x1="229" x2="354"
y1="159" y2="206" ss="1" a="2"></m><m x1="228" x2="354" y1="217" y2="263" ss="1" a="3"></m><c
start="0" stop="2"></c><c start="1" stop="1"></c><c start="2" stop="0"></c><c start="3"
stop="3"></c>

QUESTION NO: 11

Which two statements about ICMP are true? (Choose two.)

A. It is a connection-oriented protocol that provides full-duplex stream service.

B. It encapsulates route redirect data.

C. It defines the method used to map an Ethernet address to an IP address.

D. It is a communication protocol that allows remote network administrators to monitor and control
network devices.

E. It provides an error detection mechanism.

Answer: B,E

QUESTION NO: 12

A system administrator is attempting to add a default router using the command:

route add default 192.20.20.1 0

You get the error message "Network is unreachable." The IP address of the host you are using is
192.20.20.10, and the router 192.20.20.1 is reachable using a "direct" route. The router 192.20.20.1 is
on the network in question and is a viable default router.

What causes the error message "Network is unreachable"?

A. Your default router should be reachable indirectly.

B. Default routers can only be added through a file at boot-up .

C. You already have several default routers.

D. You should act as the default router to your own network.

E. The metric of 0 should be 1.

Answer: E
QUESTION NO: 13

Which command can be used to unconfigure and remove the logical interface hme0:2, given that it has
the IP address 192.168.1.2?

A. ifconfig hme0 rmif 192.168.1.2

B. ifconfig hme0:2 down

C. ifconfig hme0 removeif hme0:2

D. ifconfig hme0:2 unplumb

Answer: D

QUESTION NO: 14

TCP segments are being routed in IP datagrams. When will a destination peer receive TCP segments that
are out of order?

A. when the IP datagrams arrive out of order at the destination end

B. when the segments are transmitted out of order

C. when the IP datagrams are corrupt

D. when the TCP segments are corrupt

E. when the IP datagrams that carry the TCP data are fragmented

Answer: A
QUESTION NO: 15

A workstation does not have access to the 200.20.50.0 network. A system administrator needs to enable
access to a host at IP address 200.20.50.100. Other hosts on the same network must remain
inaccessible. Which command accomplishes this?

A. route add myrouter 200.20.50.100 0

B. route add host 200.20.50.100 myrouter 1

C. netstat -a 200.20.50.100 200.20.50.0

D. ifconfig -a qfe2 200.20.50.100 broadcast 200.20.50.255

E. route add net 200.20.50.100 myrouter 1

Answer: B

QUESTION NO: 16 DRAG DROP

Click the Task button.

Place each action on the corresponding file that is modified as a result of the action.
Answer: <m x1="14" x2="119" y1="220" y2="252" ss="0" a="0"></m><m x1="128" x2="230" y1="222"
y2="252" ss="0" a="1"></m><m x1="241" x2="343" y1="221" y2="252" ss="0" a="2"></m><m x1="39"
x2="144" y1="61" y2="93" ss="1" a="0"></m><m x1="39" x2="144" y1="97" y2="133" ss="1"
a="1"></m><m x1="39" x2="145" y1="140" y2="172" ss="1" a="2"></m><c start="2" stop="0"></c><c
start="0" stop="1"></c><c start="1" stop="2"></c>

QUESTION NO: 17

Which two are benefits of IPv6? (Choose two.)

A. smaller addresses

B. smaller routing tables

C. eliminates broadcast traffic

D. faster ARP/RARP

E. more efficient routing

Answer: C,E
QUESTION NO: 18 CORRECT TEXT

An Internet Service Provider needs to have addresses for 1000 hosts.

How many Class C address ranges are required for CIDR supernetting? Answer:

Answer: 4

QUESTION NO: 19 CORRECT TEXT

What is the full default path name of the NTP configuration file? Answer:

Answer: /ETC/INET/NTP.CONF

QUESTION NO: 20

Which is equivalent to the CIDR notation X.X.X.X/19?

A. 255.255.224.0 network mask

B. Class C address

C. Class B netmask

D. 64 possible hosts

Answer: A
QUESTION NO: 21

A DHCP client has been configured with the RELEASE_ON_SIGTERM=yes parameter. Which two actions
can be taken to force a DHCP client to relinquish the IP address it has obtained through DHCP on hme0?
(Choose two.)

A. use the stop option of the ifconfig hme0 dhcp command

B. use the dhcpagent command with the r option

C. use the command pkill -9 dhcpagent on the client

D. use the dhcpinfo command with the r option

E. use the release option of the ifconfig hme0 dhcp command

F. shut down the DHCP client

Answer: E,F

QUESTION NO: 22

Which two files are edited on an DHCP client with one network interface hme0 to ensure that the client
uses its own host name and does NOT try to obtain a host name through DHCP? (Choose two.)

A. /etc/hosts

B. /etc/inet/dhcpsvc.conf

C. /etc/hostname.hme0

D. /var/dhcp/dhcptab

E. /etc/default/dhcpagent

Answer: C,E
QUESTION NO: 23 DRAG DROP

Click the Task button.

Place each component of an Ethernet-II frame on its corresponding position in the frame.

Answer: <m x1="5" x2="106" y1="40" y2="79" ss="0" a="0"></m><m x1="115" x2="219" y1="40"
y2="78" ss="0" a="1"></m><m x1="229" x2="330" y1="40" y2="78" ss="0" a="2"></m><m x1="342"
x2="442" y1="41" y2="80" ss="0" a="3"></m><m x1="450" x2="554" y1="40" y2="80" ss="0"
a="4"></m><m x1="21" x2="122" y1="129" y2="166" ss="1" a="0"></m><m x1="123" x2="227"
y1="127" y2="169" ss="1" a="1"></m><m x1="229" x2="331" y1="129" y2="167" ss="1" a="2"></m><m
x1="333" x2="436" y1="130" y2="168" ss="1" a="3"></m><m x1="438" x2="539" y1="129" y2="168"
ss="1" a="4"></m><c start="4" stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c
start="1" stop="3"></c><c start="2" stop="4"></c>

QUESTION NO: 24

If JumpStart clients are on a different subnet to the DHCP server, what must be configured to enable
them to communicate with the DHCP server?

A. a BOOTP relay
B. a firewall to perform NAT for the JumpStart client

C. a boot server on the same network as the DHCP server

D. DNS server on their network

Answer: A

QUESTION NO: 25

Which two statements about the /etc/named.conf file are true? (Choose two.)

A. It allows nslookup to resolve queries.

B. It informs in.named which zones it supports as a primary or secondary.

C. It configures a primary with the addresses of secondary servers.

D. It informs a secondary server of the address of the primary.

Answer: B,D

QUESTION NO: 26 DRAG DROP

Click the Task button.

Place each term on its corresponding layer of the TCP/IP model.

Answer: <m x1="14" x2="134" y1="66" y2="113" ss="0" a="0"></m><m x1="16" x2="134" y1="123"
y2="169" ss="0" a="1"></m><m x1="16" x2="133" y1="178" y2="225" ss="0" a="2"></m><m x1="15"
x2="135" y1="235" y2="282" ss="0" a="3"></m><m x1="16" x2="134" y1="291" y2="337" ss="0"
a="4"></m><m x1="176" x2="295" y1="67" y2="113" ss="1" a="0"></m><m x1="175" x2="294"
y1="122" y2="170" ss="1" a="1"></m><m x1="174" x2="293" y1="178" y2="225" ss="1" a="2"></m><m
x1="175" x2="294" y1="233" y2="282" ss="1" a="3"></m><m x1="175" x2="295" y1="290" y2="337"
ss="1" a="4"></m><c start="1" stop="0"></c><c start="2" stop="4"></c><c start="3" stop="1"></c><c
start="4" stop="2"></c><c start="0" stop="3"></c>

QUESTION NO: 27

A DNS server fails when attempting to resolve www.abc.com to an IP address. You want to make the
nslookup command reference the DNS server 192.9.9.6 without modifying the /etc/resolv.conf file.
Which command accomplishes this?

A. nslookup - 192.9.9.6

B. nslookup -192.9.9.6
C. nslookup 192.9.9.6

D. nslookup / 192.9.9.6

E. nslookup -- 192.9.9.6

Answer: A

QUESTION NO: 28

An application using UDP generates a message which is longer than the MTU value that the network
architecture allows. On which layer of the TCP/IP stack does fragmentation and reassembly take place?

A. Network Interface Layer

B. Transport Layer

C. Hardware Layer

D. Application Layer

E. Internet Layer

Answer: E

QUESTION NO: 29 CORRECT TEXT

Given that you have accepted the dhcpmgr default path name for the data store, what is the full path
name to the file containing the DHCP macro definitions? Answer:

Answer: /VAR/DHCP/DHCPTAB
QUESTION NO: 30

You configured an NTP server to use its local undisciplined clock and also an external server at address
192.20.20.1. Additionally, you created a fudge line:

server 127.127.1.0 prefer

server 192.20.20.1

fudge 127.127.1.0 stratum 12

What is the purpose of the fudge line?

A. to ensure that the NTP protocol is currently disabled

B. to make the xntpd daemon check the clients clock every 12 minutes

C. to ensure that the synchronization is checked at 12:00 P.M. each day

D. to ensure that the server's local clock is seen as a stratum 12 server

Answer: D

QUESTION NO: 31

Which is a legal reverse zone?

A. 85.168.194.in-addr.arpa

B. in-addr.arpa.gvon.com

C. 85.168.194.in-addr.arpa.net
D. 85.168.194.arpa.in-addr

Answer: A

QUESTION NO: 32

Which is the minimum layer reached by all IPv6 datagrams when passing through a router?

A. Application Layer

B. Internet Layer

C. Network Interface Layer

D. Transport Layer

E. Physical Layer

Answer: B

QUESTION NO: 33

Which file contains the definitions for the default and vendor-specific DHCP options and symbols?

A. /etc/default/dhcp

B. /var/dhcp/inittab

C. /etc/dhcp/inittab

D. /etc/default/dhcpagent
Answer: C

QUESTION NO: 34 CORRECT TEXT

What is the length, in bits, of the network interface-specific identifier (VID) of the Ethernet address?
Answer:

Answer: 24

QUESTION NO: 35 DRAG DROP

Click the Task button.

When investigating tunneling, you decide to use snoop to examine the way header and encapsulation
works. You ping the destination address of the tunnel and get a successful reply. In the snoop output
you discover these protocols:

ICMPv6

ETHER

IPv6

IPv4

Place the protocol types in the order of encapsulation in which they would be observed in the snoop
output.

Note: Box 1 should contain the outermost protocol in terms of encapsulation, and Box 4 should contain
the innermost encapsulated protocol.
Answer: <m x1="18" x2="88" y1="33" y2="82" ss="0" a="0"></m><m x1="98" x2="169" y1="33"
y2="78" ss="0" a="1"></m><m x1="177" x2="248" y1="34" y2="81" ss="0" a="2"></m><m x1="257"
x2="327" y1="34" y2="81" ss="0" a="3"></m><m x1="18" x2="89" y1="138" y2="183" ss="1"
a="0"></m><m x1="98" x2="169" y1="138" y2="183" ss="1" a="1"></m><m x1="179" x2="249"
y1="137" y2="183" ss="1" a="2"></m><m x1="257" x2="330" y1="136" y2="185" ss="1" a="3"></m><c
start="1" stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c start="2"
stop="3"></c>

QUESTION NO: 36

Which two statements about ICMP are true? (Choose two.)

A. It defines the method used to map an Ethernet address to an IP address.

B. It encapsulates route redirect data.

C. It provides an error detection mechanism.

D. It is a connection-oriented protocol that provides full-duplex stream service.

E. It is a communication protocol that allows remote network administrators to monitor and control
network devices.

Answer: B,C
QUESTION NO: 37

You use the default router file in /etc to establish a default router to use for all indirectly routed packets.
Which two are benefits of using this file? (Choose two.)

A. It allows the addition of default and non-default routes dynamically.

B. The RIP daemon is not started, but the RDISC daemon is.

C. Additional routing processes are not started.

D. The routing table remains small.

E. It allows the machine to broadcast the default to other machines.

Answer: C,D

QUESTION NO: 38

Which network device type can translate between different Network Interface Layer protocols?

A. repeater

B. bridge

C. hub

D. network interface card

Answer: B
QUESTION NO: 39

A DNS server fails when attempting to resolve www.abc.com to an IP address. You want to make the
nslookup command reference the DNS server 192.9.9.6 without modifying the /etc/resolv.conf file.
Which command accomplishes this?

A. nslookup - 192.9.9.6

B. nslookup / 192.9.9.6

C. nslookup -192.9.9.6

D. nslookup -- 192.9.9.6

E. nslookup 192.9.9.6

Answer: A

QUESTION NO: 40

Click the Exhibit button.

Which two commands need to be executed to properly implement multipathing? (Choose two.)
A. ifconfig hme1 group mpgrp-one

B. ifconfig hme1 plumb 192.168.1.45 netmask + broadcast + group mpgrp-one up

C. ifconfig hme1 addif 192.168.1.51 deprecated netmask

+ broadcast + -failover up

D. ifconfig hme0 addif 192.168.1.50 deprecated netmask

+ broadcast + -failover up

E. eeprom local-mac-address?=true

Answer: A,C

QUESTION NO: 41

Given:
route add host lion tiger 1

Which two statements are true? (Choose two.)

A. The command adds a static route to the routing table.

B. The command indicates that tiger is an intermediate host on this route.

C. All hosts on the lion network could be reached as a result of the command.

D. The command indicates that lion is the only intermediate host on this route.

E. The command causes hosts tiger and lion to update their routing tables.

Answer: A,B

QUESTION NO: 42

Which two statements describe the function of a bridge? (Choose two.)

A. It connects two or more network segments.

B. It connects two or more hosts to a hub.

C. It forwards packets between networks.

D. It filters packets by MAC addresses.

Answer: A,D

QUESTION NO: 43
Which three parameters are held in the dhcp_network file? (Choose three.)

A. Server_IP

B. Timserv

C. Client_IP

D. Client_ID

E. LeaseTim

F. LeaseNeg

Answer: A,C,D

QUESTION NO: 44

Which file is read by the in.rarpd daemon?

A. /etc/ethers

B. /etc/netgroup

C. /etc/netmasks

D. /etc/inetd.conf

E. /etc/inet/rarp.conf

Answer: A

QUESTION NO: 45
Which is a legal reverse zone?

A. 85.168.194.in-addr.arpa

B. 85.168.194.in-addr.arpa.net

C. 85.168.194.arpa.in-addr

D. in-addr.arpa.gvon.com

Answer: A

QUESTION NO: 46

What is the official international standard for time?

A. Sidereal Time

B. Universal Time Coordinated

C. Eastern Standard Time

D. Greenwich Mean Time

Answer: B

QUESTION NO: 47

Which file determines the sequence and order of steps in the process of boot-time routing
configuration?

A. /etc/init.d/inetinit
B. /etc/default/in.routed

C. /etc/inet/inetd.conf

D. /etc/init.d/inetsvc

E. /etc/route.conf

Answer: A

QUESTION NO: 48

A DNS server is successfully providing information related to zones for which it is authoritative. A
problem occurs when it attempts to resolve addresses in zones for which it is not authoritative. What is
a possible cause of this problem?

A. The server has only a single Ethernet interface.

B. The server does NOT support a .com domain.

C. The server has no knowledge of the root level servers.

D. The server has no /etc/resolv.conf file.

E. The server is NOT authoritative for any reverse domains.

Answer: C

QUESTION NO: 49

What are two functions of the Type field of an Ethernet frame? (Choose two.)

A. It helps the receiving interface to determine the starting bit of an Ethernet frame.
B. It defines the protocol that will process the encapsulated data.

C. It describes the data encapsulated in the payload section of an Ethernet frame.

D. It is used for error detection.

E. It identifies the location of the target system on the local link.

Answer: B,C

QUESTION NO: 50

What is the purpose of NTP?

A. to synchronize clocks within a global network

B. to synchronize clocks within a local network

C. to provide an accurate network clock transmitter

D. to register clock differences within a network

Answer: A

QUESTION NO: 51

Given the portion of in.dhcpd output running in debug mode:

3cdbc114: There is no 192.6.17.0 dhcp-network table.

3cdbc114: Datagram received on network device: hme0.

Which two are executed on the DHCP server for the DHCP client to obtain an IP address? (Choose two.)

A. pntadm -C 192.6.17.0

B. touch /etc/dhcp.hme0

C. pntadm -r SUNWfiles -p /var/dhcp -A 192.6.17.97 192.6.17.0

D. ifconfig hme0 dhcp start

E. init 6

Answer: A,C

QUESTION NO: 52 CORRECT TEXT

What is the length, in bits, of the network interface-specific identifier (VID) of the Ethernet address?
Answer:

Answer: 24

QUESTION NO: 53

Which domain name is the uppermost in the branch of the DNS tree related to reverse lookups?

A. in-addr

B. arpa

C. net

D. com
Answer: B

QUESTION NO: 54

Which two are true for multipathing? (Choose two.)

A. disables repair detection by default

B. provides outbound load spreading

C. dynamically fails over to a network interface in another group

D. can be configured for both IPv4 and IPv6

E. uses host-based Ethernet address for configured interfaces

Answer: B,D

QUESTION NO: 55

Which two files are edited on an DHCP client with one network interface hme0 to ensure that the client
uses its own host name and does NOT try to obtain a host name through DHCP? (Choose two.)

A. /etc/hosts

B. /etc/default/dhcpagent

C. /var/dhcp/dhcptab

D. /etc/hostname.hme0

E. /etc/inet/dhcpsvc.conf

Answer: B,D
QUESTION NO: 56

Which three parameters are held in the dhcp_network file? (Choose three.)

A. Timserv

B. LeaseTim

C. LeaseNeg

D. Client_ID

E. Client_IP

F. Server_IP

Answer: D,E,F

QUESTION NO: 57

A host with network interfaces 200.3.34.18 and 200.4.64.23 broadcasts its routing table every 30
seconds. What routing daemon is running?

A. ospf

B. in.rdisc

C. inetd

D. defaultroute

E. in.routed

Answer: E
QUESTION NO: 58

An application using UDP generates a message which is longer than the MTU value that the network
architecture allows. On which layer of the TCP/IP stack does fragmentation and reassembly take place?

A. Transport Layer

B. Hardware Layer

C. Internet Layer

D. Application Layer

E. Network Interface Layer

Answer: C

QUESTION NO: 59

Which protocol supports Classless Interdomain Routing (CIDR)?

A. Border Gateway Protocol

B. Internet Control Message Protocol

C. Interior Gateway Protocol

D. Router Discovery Protocol

E. External Gateway Protocol

Answer: A
QUESTION NO: 60

The traceroute command shows routing paths to a given destination. What protocols are used by this
diagnostic tool?

A. HTTP + IP

B. SNMP + IP

C. SNMP + TCP

D. TCP + IP

E. ICMP + IP

Answer: E

QUESTION NO: 61

A DNS server is configured as a secondary server and successfully synchronizes with the primary server
when the secondary server is first started. A zone file on the primary server is updated but the
secondary server fails to synchronize. The secondary server is rebooted but this fails to help. Which
failure caused this problem?

A. failure to update the NS record of the updated zone file

B. failure to update the serial number of the updated zone file

C. failure to update the time stamp of the updated zone file

D. failure to update the SOA ttl number of the updated zone file

Answer: B
QUESTION NO: 62

A system administrator is configuring routing on a host. Which file prevents dynamic updates to the
route table?

A. /etc/gateways

B. /etc/defaultrouter

C. /etc/default/route

D. /etc/default/notroute

Answer: B

QUESTION NO: 63

Which command can be used to unconfigure and remove the logical interface hme0:2, given that it has
the IP address 192.168.1.2?

A. ifconfig hme0 removeif hme0:2

B. ifconfig hme0 rmif 192.168.1.2

C. ifconfig hme0:2 down

D. ifconfig hme0:2 unplumb

Answer: D

QUESTION NO: 64 DRAG DROP

Click the Task button.

Place each TCP/IP protocol or standard on its corresponding layer of the TCP/IP model.

Answer: <m x1="39" x2="166" y1="24" y2="70" ss="0" a="0"></m><m x1="39" x2="168" y1="80"
y2="126" ss="0" a="1"></m><m x1="39" x2="169" y1="135" y2="183" ss="0" a="2"></m><m x1="39"
x2="168" y1="192" y2="239" ss="0" a="3"></m><m x1="39" x2="169" y1="248" y2="295" ss="0"
a="4"></m><m x1="265" x2="390" y1="25" y2="70" ss="1" a="0"></m><m x1="262" x2="392" y1="80"
y2="128" ss="1" a="1"></m><m x1="263" x2="392" y1="136" y2="184" ss="1" a="2"></m><m x1="263"
x2="392" y1="193" y2="241" ss="1" a="3"></m><m x1="265" x2="391" y1="247" y2="295" ss="1"
a="4"></m><c start="0" stop="2"></c><c start="1" stop="0"></c><c start="2" stop="4"></c><c
start="3" stop="3"></c><c start="4" stop="1"></c>

QUESTION NO: 65

Which two statements about the /etc/named.conf file are true? (Choose two.)

A. It allows nslookup to resolve queries.

B. It informs a secondary server of the address of the primary.

C. It configures a primary with the addresses of secondary servers.

D. It informs in.named which zones it supports as a primary or secondary.

Answer: B,D

QUESTION NO: 66

Click the Exhibit button.

Which two commands need to be executed to properly implement multipathing? (Choose two.)

A. ifconfig hme1 plumb 192.168.1.45 netmask + broadcast + group mpgrp-one up

B. ifconfig hme0 addif 192.168.1.50 deprecated netmask

+ broadcast + -failover up

C. ifconfig hme1 addif 192.168.1.51 deprecated netmask

+ broadcast + -failover up

D. eeprom local-mac-address?=true

E. ifconfig hme1 group mpgrp-one

Answer: C,E

QUESTION NO: 67

Which causes a DHCP client to use its own host name?

A. removal of the /etc/dhcp.hme0 file

B. the appropriate entry in the /etc/hostname.hme0 file

C. Client host name must exist in the DHCP database on the server.

D. commenting out the RELEASE_ON_SIGTERM=yes parameter

Answer: B

QUESTION NO: 68

Which two commands allow you to add a client IP address to the DHCP IP address database file?
(Choose two.)

A. dhcpinfo

B. dhcpmgr
C. dhtadm

D. pntadm

Answer: B,D

QUESTION NO: 69

An application must use a connection-oriented protocol to transfer data. Which statement about this
method of data transfer is true?

A. Transmission of data can begin only when packet transit time has been established.

B. Transmission of data can begin only when the ARP reply packet size has been renegotiated.

C. Transmission of data can begin only when the routing vector has been minimized.

D. Transmission of data can begin only when the remote server sends an initial acknowledgment.

Answer: D

QUESTION NO: 70

Which three network techniques use a ring topology? (Choose three.)

A. ATM

B. Ethernet

C. Token Ring

D. CDDI

E. Token Bus
F. FDDI

Answer: C,D,F

QUESTION NO: 71

What is the correct format for zone file record lines?

A. [servername] [ttl] class record_type record_data

B. [name] [ttl] class record_type record_data

C. [ttl] [name] class record_type record_data

D. [DomainIP] [ttl] class record_type record_data

Answer: B

QUESTION NO: 72

Given the command:

# snoop -v 192.168.1.4 192.168.1.7

Which two statements about the output are correct? (Choose two.)

A. You would see all broadcast packets.

B. You would see multiple lines of output for each level of encapsulation.
C. You would see packets sent to all IP addresses in the range between 192.168.1.4 and 192.168.1.7.

D. You would see all packets sent to host 192.168.1.4 and host 192.168.1.7.

E. You would see packets sent between host 192.168.1.4 and host 192.168.1.7.

Answer: B,E

QUESTION NO: 73

What is the purpose of NTP?

A. to synchronize clocks within a global network

B. to provide an accurate network clock transmitter

C. to register clock differences within a network

D. to synchronize clocks within a local network

Answer: A

QUESTION NO: 74

In the five-layer TCP/IP model, which function does the Transport Layer provide?

A. data formatting

B. end-to-end data transfer

C. physical connections

D. data routing
Answer: B

QUESTION NO: 75

Which file is read by the in.rarpd daemon?

A. /etc/inetd.conf

B. /etc/inet/rarp.conf

C. /etc/netgroup

D. /etc/netmasks

E. /etc/ethers

Answer: E

QUESTION NO: 76

Given the current origin is gvon.com, which two zone file lines correctly delegate the domain
training.gvon.com. to a server called centauri.gvon.com.? (Choose two.)

A. centauri.gvon.com. in NS gvon.com.

B. gvon in NS centauri.gvon.com.

C. training.gvon.com. in NS centauri.gvon.com.

D. training in NS centauri.gvon.com.

E. gvon.com in NS centauri.gvon.com.

F. training. in NS centauri.gvon.com.
Answer: C,D

QUESTION NO: 77

Which three monitoring tools are available for NTP? (Choose three.)

A. ntpdebug

B. ntpq

C. xntptrace

D. ntptrace

E. xntpdc

Answer: B,D,E

QUESTION NO: 78

Which two are benefits of using DHCP? (Choose two.)

A. DHCP reduces the cost of managing networks by automatic assignment of available IP addresses from
a pool of addresses.

B. DHCP servers support BOOTP and RARP clients.

C. DHCP on Solaris includes a VPN feature that allows for the dynamic setup of an IP-over-IP tunnel.

D. DHCP allows setting up BOOTP and RARP relays.

E. DHCP is a replacement for JumpStart.

F. DHCP supports clients that boot over a network, effectively replacing the need for RARP and the
bootparams file.

Answer: A,F

QUESTION NO: 79

Given the snoop trace that was run for three minutes:

sys10 -> sys4 NTPclient (Fri May10 14:45:02 2002)

sys4 -> sys10 NTPserver (Fri May 10 14:44:37 2002)

sys10 -> sys4 NTPclient (Fri May 10 14:46:06 2002)

sys4 -> sys10 NTPserver (Fri May 10 14:45:43 2002)

sys10 -> sys4 NTPclient (Fri May 10 14:47:10 2002)

sys4 -> sys10 NTPserver (Fri May 10 14:46:47 2002)

What is a reason that the NTP client has NOT changed its time?

A. The NTP client daemon process is NOT running.

B. The NTP client is configured as a broadcast client.

C. The NTP server daemon process is NOT running.

D. The NTP client needs to receive more updates from its server.

Answer: D
QUESTION NO: 80

Which statement about supporting JumpStart installations by DHCP is true?

A. The JumpStart client must be upgraded to OpenBoot PROM revision 3.25 or higher.

B. The JumpStart server and the DHCP server must be one and the same machine.

C. add_install_client on the JumpStart server automatically performs the necessary configuration on the
DHCP server.

D. A DHCP server must be set up in each subnet with JumpStart clients.

Answer: A

QUESTION NO: 81

What protocol defines the Router Discovery (RDISC) messages?

A. ICMP

B. DHCP

C. ARP

D. IP

Answer: A

QUESTION NO: 82

Which two statements about a service in the client-server model are true? (Choose two.)
A. A service must be listed in /etc/services.

B. A service is started only at system boot.

C. A service is provided by a process.

D. A service always occurs across a network link.

E. A service is accessed by a process.

Answer: C,E

QUESTION NO: 83

Given the DHCP debug output:

3cdbd723: Datagram received on network device: hme0

3cdbd723: Reserved offer: 192.1.29.72

3cdbd724: Unicasting datagram to 192.1.29.72 address.

3cdbd724: Adding ARP entry: 192.1.29.72 == 080020CBCBCB

3cdbd724: Updated offer: 192.1.29.72

3cdbd725: Datagram received on network device: hme0

3cdbd725: Client: 01080020CBCBCB maps to IP: 192.1.29.72

3cdbd725: Unicasting datagram to 192.1.29.72 address.

3cdbd725: Adding ARP entry: 192.1.29.72 == 080020CBCBCB

What does this output indicate?

A. The server received the client's request but is NOT able to send an answer to the client, and therefore
repeats its answer unicast.

B. The IP address is permanently reserved for another client.

C. The IP address assignment was successfully completed.

D. The client requested an IP address that is already assigned to another host with MAC address
08:00:20:cb:cb:cb.

Answer: C

QUESTION NO: 84 DRAG DROP

Click the Task button.

Place each network component on the TCP/IP model layer at which it operates.

Answer: <m x1="47" x2="175" y1="58" y2="103" ss="0" a="0"></m><m x1="47" x2="173" y1="112"
y2="161" ss="0" a="1"></m><m x1="48" x2="174" y1="170" y2="215" ss="0" a="2"></m><m x1="47"
x2="173" y1="226" y2="273" ss="0" a="3"></m><m x1="241" x2="365" y1="58" y2="106" ss="1"
a="0"></m><m x1="238" x2="366" y1="113" y2="161" ss="1" a="1"></m><m x1="239" x2="365"
y1="171" y2="217" ss="1" a="2"></m><m x1="238" x2="367" y1="225" y2="271" ss="1" a="3"></m><c
start="0" stop="2"></c><c start="1" stop="1"></c><c start="2" stop="0"></c><c start="3"
stop="3"></c>

QUESTION NO: 85

In the five-layer TCP/IP model, which two functions does the Network Interface Layer provide? (Choose
two.)

A. packet framing

B. data addressing between networks

C. connections between applications

D. Cyclic Redundancy Checking

Answer: A,D

QUESTION NO: 86

Which two are causes of clock drift? (Choose two.)

A. GMT

B. higher priority interrupts

C. oscillator frequency variation

D. encryption

E. UTC
Answer: B,C

QUESTION NO: 87

Given a portion of the /etc/inet/dhcpsvc.conf file:

DAEMON_ENABLED=TRUE

RUN_MODE=relay

RESOURCE=SUNWfiles

PATH=/var/dhcp

Which system has these entries in the /etc/inet/dhcpsvc.conf file?

A. a system running in.dhcpd -r

B. a DHCP server

C. a system running in.dhcpd in debug mode

D. a DHCP client

Answer: A

QUESTION NO: 88

Following a collision during normal Ethernet communication, what type of backoff technique is used to
calculate a random period of time to prevent the colliding systems from colliding again when
transmitting?
A. extracted

B. extensive

C. extraneous

D. exponential

E. exhaustive

Answer: D

QUESTION NO: 89

Which two are benefits of using DHCP? (Choose two.)

A. DHCP is a replacement for JumpStart.

B. DHCP on Solaris includes a VPN feature that allows for the dynamic setup of an IP-over-IP tunnel.

C. DHCP reduces the cost of managing networks by automatic assignment of available IP addresses from
a pool of addresses.

D. DHCP servers support BOOTP and RARP clients.

E. DHCP supports clients that boot over a network, effectively replacing the need for RARP and the
bootparams file.

F. DHCP allows setting up BOOTP and RARP relays.

Answer: C,E

QUESTION NO: 90 CORRECT TEXT

An Internet Service Provider needs to have addresses for 1000 hosts.

How many Class C address ranges are required for CIDR supernetting? Answer:

Answer: 4

QUESTION NO: 91

Which two are functions of the dhcpagent process? (Choose two.)

A. updates the DHCP datastores

B. manages the IP address space of connected networks

C. responds to DHCPDISCOVER packets

D. caches the information for use in configuration of the interface

E. releases IP addresses or negotiates lease renewals

Answer: D,E

QUESTION NO: 92

Which command is used to display Ethernet interface packet statistics?

A. snoop -v

B. netstat -i

C. ifconfig -a
D. netstat -a

Answer: B

QUESTION NO: 93

Which two statements about the /etc/named.conf file are true? (Choose two.)

A. It informs in.named which zones it supports as a primary or secondary.

B. It informs a secondary server of the address of the primary.

C. It configures a primary with the addresses of secondary servers.

D. It allows nslookup to resolve queries.

Answer: A,B

QUESTION NO: 94

A printer is connected to the same subnet as your workstation. The printer is identified as:

host name IP address MAC address

printer1 192.204.200.12 8:0:20:21:38:6b

Which command allows your workstation to reply to ARP requests for the printer?

A. arp -s printer1 8:0:20:21:38:6b pub

B. rarp -s 192.204.200.12 8:0:20:21:38:6b

C. arp -p printer1 8:0:20:21:38:6b

D. netconfig -p 192.204.200.12 printer1

Answer: A

QUESTION NO: 95

Given the command:

# snoop -v 192.168.1.4 192.168.1.7

Which two statements about the output are correct? (Choose two.)

A. You would see all packets sent to host 192.168.1.4 and host 192.168.1.7.

B. You would see multiple lines of output for each level of encapsulation.

C. You would see packets sent to all IP addresses in the range between 192.168.1.4 and 192.168.1.7.

D. You would see packets sent between host 192.168.1.4 and host 192.168.1.7.

E. You would see all broadcast packets.

Answer: B,D

QUESTION NO: 96

How do you run DHCP in debug mode on a DHCP client?

A. You kill the DHCP client process and edit the DHCP start script to include the DHCP_DEBUG=true;
export DHCP_DEBUG statement. You then run the DHCP start script.

B. You kill the DHCP client process and set DHCP_DEBUG=true in the dhcpagent configuration file.

C. You kill the DHCP client process then relaunch the client process using the /sbin/dhcpagent -d2
command.

D. You kill the DHCP client process and edit the DHCP start script to use the in.dhcpd -i <interface> -d -v
command. You then run the

DHCP start script.

Answer: C

QUESTION NO: 97

Which two statements about a Layer 2 switch are true? (Choose two.)

A. A switch can connect more than one pair of cable segments simultaneously.

B. A switch can dynamically connect and disconnect two cable segments without operator intervention.

C. A switch can convert between two different protocol suites.

D. A switch can filter and selectively forward a packet based on the IP address in the packet.

Answer: A,B

QUESTION NO: 98

Which is equivalent to the CIDR notation X.X.X.X/19?

A. Class C address

B. 255.255.224.0 network mask

C. 64 possible hosts

D. Class B netmask

Answer: B

QUESTION NO: 99

Which causes a DHCP client to use its own host name?

A. Client host name must exist in the DHCP database on the server.

B. commenting out the RELEASE_ON_SIGTERM=yes parameter

C. removal of the /etc/dhcp.hme0 file

D. the appropriate entry in the /etc/hostname.hme0 file

Answer: D

QUESTION NO: 100

Given the portion of in.dhcpd output running in debug mode:

3cdbc114: There is no 192.6.17.0 dhcp-network table.

3cdbc114: Datagram received on network device: hme0.

Which two are executed on the DHCP server for the DHCP client to obtain an IP address? (Choose two.)

A. touch /etc/dhcp.hme0

B. ifconfig hme0 dhcp start

C. init 6

D. pntadm -C 192.6.17.0

E. pntadm -r SUNWfiles -p /var/dhcp -A 192.6.17.97 192.6.17.0

Answer: D,E

QUESTION NO: 101

Which command is used to display Ethernet interface packet statistics?

A. ifconfig -a

B. netstat -i

C. netstat -a

D. snoop -v

Answer: B

QUESTION NO: 102

A system boots and has a configured network interface. At minimum, what type of route is
automatically added to the routing table?
A. static indirect

B. dynamic indirect

C. static direct

D. dynamic direct

Answer: C

QUESTION NO: 103

How do you run DHCP in debug mode on a DHCP client?

A. You kill the DHCP client process and edit the DHCP start script to use the in.dhcpd -i <interface> -d -v
command. You then run the DHCP start script.

B. You kill the DHCP client process and edit the DHCP start script to include the DHCP_DEBUG=true;
export DHCP_DEBUG statement. You then run the DHCP start script.

C. You kill the DHCP client process and set DHCP_DEBUG=true in the dhcpagent configuration file.

D. You kill the DHCP client process then relaunch the client process using the /sbin/dhcpagent -d2
command.

Answer: D

QUESTION NO: 104

Which layer of the TCP/IP five-layer model contains UDP?

A. Transport Layer

B. Application Layer
C. Network Interface Layer

D. Internet Layer

E. Hardware Layer

Answer: A

QUESTION NO: 105

A host with network interfaces 200.3.34.18 and 200.4.64.23 broadcasts its routing table every 30
seconds. What routing daemon is running?

A. defaultroute

B. in.rdisc

C. ospf

D. inetd

E. in.routed

Answer: E

QUESTION NO: 106

A DNS server is giving an error for the following SOA record:

@ soa in host1.abc.com. root.abc.com. (

1002

10800
 3800

604800

10800)

What is causing the error?

A. A serial number of 1002 is too small.

B. The () pair should be {}.

C. The soa and in fields are in the wrong order.

D. soa must be in upper case.

E. The final ")" must be on a line by itself.

Answer: C

QUESTION NO: 107

The address 197.20.71.0 identifies a network that you want to identify with a name. Which file, if edited,
will identify the network address with a name?

A. /etc/default/networks.conf

B. /etc/inet/networks.conf

C. /etc/inet/networks

D. /etc/networks.conf

E. /etc/hosts

Answer: C
QUESTION NO: 108

Given:

host name IP address

myhost 200.54.42.10

printsvr 200.55.42.30

The system myhost needs to send data to printsvr. The routing table on myhost has no entry for
printsvr. The routing table on myhost has no entry for the 200.55.42.0 network.

Which entry does the routing algorithm look for next?

A. ARP cache

B. default

C. RARP

D. 200.54.42.255

E. loopback

Answer: B

QUESTION NO: 109

Which protocol does IPv6 use to discover MAC addresses?

A. Neighbor Discovery Protocol

B. Auto Configuration Protocol

C. Network Detection Protocol

D. Address Resolution Protocol

Answer: A

QUESTION NO: 110

Which command can be used to unconfigure and remove the logical interface hme0:2, given that it has
the IP address 192.168.1.2?

A. ifconfig hme0:2 unplumb

B. ifconfig hme0 rmif 192.168.1.2

C. ifconfig hme0:2 down

D. ifconfig hme0 removeif hme0:2

Answer: A

QUESTION NO: 111

A server has a single hme Ethernet interface auto-configured with an IPv6 address. Which statement
about the configuration process is true?

A. The file /etc/hostname6.hme0 exists and is empty.

B. The file /etc/hostname6.hme0 exists and contains an entry found in /etc/inet/hosts.

C. The file /etc/hostname6.hme0 does NOT exist.

D. The file /etc/hostname6.hme0 exists and contains an entry found in /etc/inet/ipnodes.

Answer: A

QUESTION NO: 112

What does @ mean in a zone file?

A. current host's IP address

B. current server's host ID

C. current origin

D. current server's name

Answer: C

QUESTION NO: 113

Due to a restructuring of your organization, your company has now been divided into four separate
groups. Your network is to be organized into four separate subnetworks, but you only have a single Class
C address range. Which file on every host on each subnetwork needs to be modified so that you can
implement an appropriate subnetworking strategy?

A. /etc/netmasks

B. /etc/netgroup

C. /etc/inet/netmask

D. /etc/inet/hostname.hme0
E. /etc/defaultrouter

Answer: A

QUESTION NO: 114

In which mode is an Ethernet card configured to pass all Ethernet frames up the protocol stack
(inbound) regardless of the Ethernet frame's destination MAC address?

A. Profligate Mode

B. Prominent Mode

C. Point-to-Point

D. PointCard Mode

E. Promiscuous Mode

Answer: E

QUESTION NO: 115

Given:

host name IP address MAC address

host1 192.40.62.10 8:0:20:75:6e:7d

Which command puts a valid entry in the ARP table for workstation host1?
A. arp -s host1 8:0:20:75:6e:7d

B. arp -d host1 192.40.62.10

C. arp -a host1

D. arp 8:0:20:75:6e:7d 192.40.62.10

E. arp -s 192.40.62.10

Answer: A

QUESTION NO: 116

What does @ mean in a zone file?

A. current server's host ID

B. current host's IP address

C. current server's name

D. current origin

Answer: D

QUESTION NO: 117

Which two can be achieved by configuring the /etc/gateways file? (Choose two.)

A. adding a default route, preventing any routing daemon from starting

B. adding additional indirect routes

C. preventing routing processes such as RIP starting

D. automatically adding static entries in the routing table when the system boots

Answer: B,D

QUESTION NO: 118

What is the correct format for zone file record lines?

A. [DomainIP] [ttl] class record_type record_data

B. [name] [ttl] class record_type record_data

C. [ttl] [name] class record_type record_data

D. [servername] [ttl] class record_type record_data

Answer: B

QUESTION NO: 119

A DHCP client has been configured with the RELEASE_ON_SIGTERM=yes parameter. Which two actions
can be taken to force a DHCP client to relinquish the IP address it has obtained through DHCP on hme0?
(Choose two.)

A. use the dhcpagent command with the r option

B. use the dhcpinfo command with the r option

C. shut down the DHCP client

D. use the release option of the ifconfig hme0 dhcp command

E. use the command pkill -9 dhcpagent on the client

F. use the stop option of the ifconfig hme0 dhcp command

Answer: C,D

QUESTION NO: 120

Given the current origin is gvon.com, which two zone file lines correctly delegate the domain
training.gvon.com. to a server called centauri.gvon.com.? (Choose two.)

A. gvon in NS centauri.gvon.com.

B. training in NS centauri.gvon.com.

C. gvon.com in NS centauri.gvon.com.

D. training.gvon.com. in NS centauri.gvon.com.

E. training. in NS centauri.gvon.com.

F. centauri.gvon.com. in NS gvon.com.

Answer: B,D

QUESTION NO: 121

Where does the NTP daemon send its error information by default?

A. directly to the controlling terminal

B. to an internal buffer from where it can be queried with an additional tool

C. to the syslog facility

D. The daemon does not report error information by default.

Answer: C

QUESTION NO: 122

Which command is used to display Ethernet interface packet statistics?

A. ifconfig -a

B. snoop -v

C. netstat -i

D. netstat -a

Answer: C

QUESTION NO: 123

You have a DHCP client on network 192.200.51.0. The DHCP server has the DHCP data in the /var/dhcp
directory. The datastore format is ASCII. What is the full default path name of the file containing the IP
address pool for the Solaris 9 client?

A. /var/dhcp/192_200_51_0

B. /var/dhcp/SUNWfiles1_192_200_51_0

C. /etc/inet/dhcp/192_200_51_0

D. /var/dhcp/SUNWfiles1.192.200.51.0
Answer: B

QUESTION NO: 124

You have configured an IPv6 router which is having problems routing correctly to a default router
connected to the Internet. You need to investigate the machine's routing table and check that the
default route is in place. You also need to check the ARP cache to see whether the MAC address of the
default router has been learned. Which two commands enable you to perform these tasks? (Choose
two.)

A. netstat -pn

B. ifconfig -a

C. netstat -m

D. arp -n

E. netstat -r

Answer: A,E

QUESTION NO: 125

Which two commands display the contents of the ARP table? (Choose two.)

A. netstat -p

B. arp -a

C. arp -s

D. ifconfig -a

E. netstat -a
F. arp -d

Answer: A,B

QUESTION NO: 126

Which two files are edited on an DHCP client with one network interface hme0 to ensure that the client
uses its own host name and does NOT try to obtain a host name through DHCP? (Choose two.)

A. /etc/inet/dhcpsvc.conf

B. /etc/hostname.hme0

C. /var/dhcp/dhcptab

D. /etc/default/dhcpagent

E. /etc/hosts

Answer: B,D

QUESTION NO: 127 DRAG DROP

Click the Task button.

Place each component of an Ethernet-II frame on its corresponding position in the frame.
Answer: <m x1="9" x2="113" y1="49" y2="88" ss="0" a="0"></m><m x1="122" x2="225" y1="50"
y2="87" ss="0" a="1"></m><m x1="234" x2="336" y1="48" y2="90" ss="0" a="2"></m><m x1="344"
x2="448" y1="49" y2="88" ss="0" a="3"></m><m x1="458" x2="559" y1="49" y2="89" ss="0"
a="4"></m><m x1="24" x2="128" y1="138" y2="175" ss="1" a="0"></m><m x1="130" x2="232"
y1="139" y2="173" ss="1" a="1"></m><m x1="234" x2="335" y1="138" y2="177" ss="1" a="2"></m><m
x1="335" x2="439" y1="136" y2="177" ss="1" a="3"></m><m x1="442" x2="544" y1="137" y2="175"
ss="1" a="4"></m><c start="4" stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c
start="1" stop="3"></c><c start="2" stop="4"></c>

QUESTION NO: 128

Given a portion of the /etc/inet/dhcpsvc.conf file:

DAEMON_ENABLED=TRUE

RUN_MODE=relay

RESOURCE=SUNWfiles

PATH=/var/dhcp

Which system has these entries in the /etc/inet/dhcpsvc.conf file?

A. a DHCP client
B. a system running in.dhcpd in debug mode

C. a system running in.dhcpd -r

D. a DHCP server

Answer: C

QUESTION NO: 129

When a system boots, which file configures Ethernet network interfaces?

A. /etc/init.d/S30network.sh

B. /etc/rcS.d/S30network.sh

C. /etc/default/netmasks

D. /etc/inittab

E. /etc/ifconfig.conf

Answer: B

QUESTION NO: 130

Which two statements about a Layer 2 switch are true? (Choose two.)

A. A switch can connect more than one pair of cable segments simultaneously.

B. A switch can filter and selectively forward a packet based on the IP address in the packet.

C. A switch can convert between two different protocol suites.

D. A switch can dynamically connect and disconnect two cable segments without operator intervention.

Answer: A,D

QUESTION NO: 131

Which daemon is responsible for default route advertisements?

A. routed

B. in.rdisc

C. rdisc

D. in.routed

Answer: B

QUESTION NO: 132

A host's IPv6 link-local unicast address is based on the host's Ethernet address. The beginning of the
address is prefixed by a specific Format Prefix (FP) value to indicate that the address is a link-local
address. In addition, a 16-bit code is inserted in 64-bit Interface ID portion of the IPv6 address to enable
a 48-bit Ethernet address to become 64 bits in length. Which value represents the 16-bit code?

A. FE80

B. FFFF

C. FEC0

D. FFFE

E. FFEE
Answer: D

QUESTION NO: 133

A DNS server is configured as a secondary server and successfully synchronizes with the primary server
when the secondary server is first started. A zone file on the primary server is updated but the
secondary server fails to synchronize. The secondary server is rebooted but this fails to help. Which
failure caused this problem?

A. failure to update the time stamp of the updated zone file

B. failure to update the serial number of the updated zone file

C. failure to update the SOA ttl number of the updated zone file

D. failure to update the NS record of the updated zone file

Answer: B

QUESTION NO: 134

Which interface flag is monitored by in.mpathd to detect whether an interface failure has occurred?

A. MULTICAST

B. NOFAILOVER

C. DEPRECATED

D. RUNNING

Answer: D
QUESTION NO: 135

You have created an IPv6 tunnel between two hosts. Which two statements are true about tunnelling?
(Choose two.)

A. The IP header of the datagram that has encapsulated the tunnelled data contains the source address
of the tunnel.

B. The tunnel source IP address is always the same as the source IP address in the IP header of the
tunnelled (encapsulated) IP datagram.

C. Tunnelled traffic is always TCP or UDP in IPv6.

D. IPv6 Solaris tunnelling always involves an IP datagram encapsulating an IP datagram.

E. Tunnelled traffic is always encrypted.

Answer: A,D

QUESTION NO: 136

Which two tasks involve changes to the dhcptab database? (Choose two.)

A. tuning the IGNORE_FAILED_ARP parameter

B. changing the definition of a macro

C. updating the pool of IP addresses assigned to clients

D. defining an additional symbol

E. changing a client macro association so that the client uses a different macro

Answer: B,D
QUESTION NO: 137 DRAG DROP

Click the Task button.

Place each component of an Ethernet-II frame on its corresponding position in the frame.

Answer: <m x1="5" x2="106" y1="47" y2="86" ss="0" a="0"></m><m x1="115" x2="219" y1="47"
y2="85" ss="0" a="1"></m><m x1="228" x2="330" y1="48" y2="86" ss="0" a="2"></m><m x1="341"
x2="442" y1="48" y2="86" ss="0" a="3"></m><m x1="453" x2="555" y1="48" y2="83" ss="0"
a="4"></m><m x1="20" x2="122" y1="135" y2="174" ss="1" a="0"></m><m x1="124" x2="227"
y1="135" y2="174" ss="1" a="1"></m><m x1="226" x2="329" y1="135" y2="174" ss="1" a="2"></m><m
x1="332" x2="433" y1="135" y2="175" ss="1" a="3"></m><m x1="436" x2="541" y1="133" y2="174"
ss="1" a="4"></m><c start="4" stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c
start="1" stop="3"></c><c start="2" stop="4"></c>

QUESTION NO: 138

Given the command:

# snoop -v 192.168.1.4 192.168.1.7

Which two statements about the output are correct? (Choose two.)

A. You would see all packets sent to host 192.168.1.4 and host 192.168.1.7.

B. You would see all broadcast packets.

C. You would see multiple lines of output for each level of encapsulation.

D. You would see packets sent to all IP addresses in the range between 192.168.1.4 and 192.168.1.7.

E. You would see packets sent between host 192.168.1.4 and host 192.168.1.7.

Answer: C,E

QUESTION NO: 139

In the five-layer TCP/IP model, which function does the Transport Layer provide?

A. data routing

B. end-to-end data transfer

C. physical connections

D. data formatting

Answer: B

QUESTION NO: 140 DRAG DROP

Click the Task button.

Place each term on its corresponding layer of the TCP/IP model.

Answer: <m x1="24" x2="143" y1="65" y2="111" ss="0" a="0"></m><m x1="24" x2="143" y1="122"
y2="168" ss="0" a="1"></m><m x1="25" x2="143" y1="178" y2="225" ss="0" a="2"></m><m x1="25"
x2="143" y1="231" y2="280" ss="0" a="3"></m><m x1="25" x2="144" y1="289" y2="337" ss="0"
a="4"></m><m x1="185" x2="302" y1="64" y2="112" ss="1" a="0"></m><m x1="185" x2="303"
y1="121" y2="168" ss="1" a="1"></m><m x1="184" x2="304" y1="177" y2="223" ss="1" a="2"></m><m
x1="184" x2="302" y1="232" y2="279" ss="1" a="3"></m><m x1="184" x2="303" y1="289" y2="337"
ss="1" a="4"></m><c start="1" stop="0"></c><c start="2" stop="4"></c><c start="3" stop="1"></c><c
start="4" stop="2"></c><c start="0" stop="3"></c>

QUESTION NO: 141

When a system boots, which file configures Ethernet network interfaces?

A. /etc/init.d/S30network.sh
B. /etc/rcS.d/S30network.sh

C. /etc/inittab

D. /etc/default/netmasks

E. /etc/ifconfig.conf

Answer: B

QUESTION NO: 142

Which is the minimum layer reached by all IPv6 datagrams when passing through a router?

A. Internet Layer

B. Physical Layer

C. Application Layer

D. Transport Layer

E. Network Interface Layer

Answer: A

QUESTION NO: 143

A system administrator is attempting to add a default router using the command:

route add default 192.20.20.1 0

You get the error message "Network is unreachable." The IP address of the host you are using is
192.20.20.10, and the router 192.20.20.1 is reachable using a "direct" route. The router 192.20.20.1 is
on the network in question and is a viable default router.

What causes the error message "Network is unreachable"?

A. You already have several default routers.

B. The metric of 0 should be 1.

C. Your default router should be reachable indirectly.

D. You should act as the default router to your own network.

E. Default routers can only be added through a file at boot-up .

Answer: B

QUESTION NO: 144

How do you run DHCP in debug mode on a DHCP client?

A. You kill the DHCP client process and edit the DHCP start script to include the DHCP_DEBUG=true;
export DHCP_DEBUG statement. You then run the DHCP start script.

B. You kill the DHCP client process and edit the DHCP start script to use the in.dhcpd -i <interface> -d -v
command. You then run the DHCP start script.

C. You kill the DHCP client process then relaunch the client process using the /sbin/dhcpagent -d2
command.

D. You kill the DHCP client process and set DHCP_DEBUG=true in the dhcpagent configuration file.

Answer: C
QUESTION NO: 145

You have created an IPv6 tunnel between two hosts. Which two statements are true about tunnelling?
(Choose two.)

A. IPv6 Solaris tunnelling always involves an IP datagram encapsulating an IP datagram.

B. Tunnelled traffic is always encrypted.

C. The tunnel source IP address is always the same as the source IP address in the IP header of the
tunnelled (encapsulated) IP datagram.

D. The IP header of the datagram that has encapsulated the tunnelled data contains the source address
of the tunnel.

E. Tunnelled traffic is always TCP or UDP in IPv6.

Answer: A,D

QUESTION NO: 146

Which two are benefits of using IP Multipathing (IPMP)? (Choose two.)

A. IPMP is an enhanced successor product to Sun Trunking, included in the Solaris OE.

B. IPMP provides packet-by-packet outbound load spreading for one single network connection.

C. IPMP allows for online deconfiguration and unplugging of network interfaces.

D. IPMP allows the sending of packets to one host through different routers.

E. IPMP provides additional security against network intrusion attacks.

F. IPMP enables the Solaris 9 Operating Environment to recover from network interface failures.
Answer: C,F

QUESTION NO: 147

Click the Exhibit button.

Which host in the exhibit is acting as an intermediate router?

A. admin-picc

B. violet

C. admin-picc3

D. samba

E. admin-d

F. localhost

Answer: B
QUESTION NO: 148

Which three network techniques use a ring topology? (Choose three.)

A. Token Ring

B. Token Bus

C. ATM

D. FDDI

E. CDDI

F. Ethernet

Answer: A,D,E

QUESTION NO: 149

Given the DHCP debug output: 3cdbd723:

Datagram received on network device: hme0

3cdbd723: Reserved offer: 192.1.29.72

3cdbd724: Unicasting datagram to 192.1.29.72 address.

3cdbd724: Adding ARP entry: 192.1.29.72 == 080020CBCBCB

3cdbd724: Updated offer: 192.1.29.72

3cdbd725: Datagram received on network device: hme0

3cdbd725: Client: 01080020CBCBCB maps to IP: 192.1.29.72

3cdbd725: Unicasting datagram to 192.1.29.72 address.

3cdbd725: Adding ARP entry: 192.1.29.72 == 080020CBCBCB

What does this output indicate?

A. The server received the client's request but is NOT able to send an answer to the client, and therefore
repeats its answer unicast.

B. The IP address assignment was successfully completed.

C. The client requested an IP address that is already assigned to another host with MAC address
08:00:20:cb:cb:cb.

D. The IP address is permanently reserved for another client.

Answer: B

QUESTION NO: 150

A DNS server is giving an error for the following SOA record:

@ soa in host1.abc.com. root.abc.com. (

1002

10800

3800

604800

10800)

What is causing the error?

A. The () pair should be {}.

B. A serial number of 1002 is too small.

C. The final ")" must be on a line by itself.

D. soa must be in upper case.

E. The soa and in fields are in the wrong order.

Answer: E

QUESTION NO: 151

What is the purpose of RARP?

A. It maps a 48-bit IP address to a 32-bit Ethernet address.

B. It maps a 48-bit Ethernet address to a 32-bit IP address.

C. It maps a 32-bit Ethernet address to a 128-bit IP address.

D. It maps a 32-bit IP address to a 48-bit Ethernet address.

E. It maps a 128-bit IP address to a 48-bit Ethernet address.

Answer: B

QUESTION NO: 152

Which is a legal reverse zone?

A. 85.168.194.in-addr.arpa
B. in-addr.arpa.gvon.com

C. 85.168.194.in-addr.arpa.net

D. 85.168.194.arpa.in-addr

Answer: A

QUESTION NO: 153

What protocol defines the Router Discovery (RDISC) messages?

A. ARP

B. ICMP

C. DHCP

D. IP

Answer: B

QUESTION NO: 154 CORRECT TEXT

What is the full path name of the NTP client configuration template file? Answer:

Answer: /ETC/INET/NTP.CLIENT

QUESTION NO: 155

In the five-layer TCP/IP model, which protocol is contained in the same layer as IP?

A. SNMP

B. TCP

C. PPP

D. ICMP

E. UDP

Answer: D

QUESTION NO: 156

You have configured an IPv6 router which is having problems routing correctly to a default router
connected to the Internet. You need to investigate the machine's routing table and check that the
default route is in place. You also need to check the ARP cache to see whether the MAC address of the
default router has been learned. Which two commands enable you to perform these tasks? (Choose
two.)

A. netstat -m

B. netstat -r

C. ifconfig -a

D. arp -n

E. netstat -pn

Answer: B,E
QUESTION NO: 157

Which two commands allow you to define a DHCP symbol? (Choose two.)

A. dhcpmgr

B. dhtadm

C. pntadm

D. dhcpinfo

Answer: A,B

QUESTION NO: 158

What are two functions of the Type field of an Ethernet frame? (Choose two.)

A. It describes the data encapsulated in the payload section of an Ethernet frame.

B. It helps the receiving interface to determine the starting bit of an Ethernet frame.

C. It defines the protocol that will process the encapsulated data.

D. It is used for error detection.

E. It identifies the location of the target system on the local link.

Answer: A,C

QUESTION NO: 159

Which two protocols are used by the ping command? (Choose two.)
A. TCP

B. ICMP

C. UDP

D. IP

Answer: B,D

QUESTION NO: 160

A DNS server has MX records which indicate that there are three SMTP relays for the domain gvon.com.
A problem occurs, whereby other DNS servers make iterative queries for the MX records every time they
are queried by clients. Which two MX lines cause remote DNS servers to refuse to cache the MX record
for SMTP relay smtp.gvon.com? (Choose two.)

A. gvon.com. mx 100 smtp.gvon.com.

B. gvon.com. 0 in mx 0 smtp.gvon.com.

C. gvon.com. in mx 5 smtp.gvon.com.

D. gvon.com. 0 in mx 5 smtp.gvon.com.

E. gvon.com. 100 in mx 10 smtp.gvon.com.

Answer: B,D

QUESTION NO: 161

Which command displays the configuration of an hme0 network interface?

A. ifconfig hme0

B. ndd /dev/hme0 \?

C. ndd hme0 \?

D. ifconfig /dev/hme0

Answer: A

QUESTION NO: 162

You configured an NTP server to use its local undisciplined clock and also an external server at address
192.20.20.1. Additionally, you created a fudge line:

server 127.127.1.0 prefer server

192.20.20.1

fudge 127.127.1.0 stratum 12

What is the purpose of the fudge line?

A. to ensure that the server's local clock is seen as a stratum 12 server

B. to ensure that the NTP protocol is currently disabled

C. to make the xntpd daemon check the clients clock every 12 minutes

D. to ensure that the synchronization is checked at 12:00 P.M. each day

Answer: A
QUESTION NO: 163

Click the Exhibit button.

Which host in the exhibit is acting as an intermediate router?

A. violet

B. admin-picc

C. samba

D. localhost

E. admin-picc3

F. admin-d

Answer: A

QUESTION NO: 164

What are two functions of the Type field of an Ethernet frame? (Choose two.)
A. It is used for error detection.

B. It describes the data encapsulated in the payload section of an Ethernet frame.

C. It identifies the location of the target system on the local link.

D. It defines the protocol that will process the encapsulated data.

E. It helps the receiving interface to determine the starting bit of an Ethernet frame.

Answer: B,D

QUESTION NO: 165

Which two statements about jabbers are true? (Choose two.)

A. Jabbers are caused by late collisions.

B. Jabbers are frames that are too short.

C. Jabbers are automatically discarded by the receiver.

D. Jabbers are a normal phenomenon in a network, and there is no reason to worry about their
occurrence.

E. Faulty sending hardware or software might be the reason for jabbers.

F. Jabbers are frames whose Ethernet headers are malformed.

Answer: C,E

QUESTION NO: 166

Which three statements about fragmentation are true? (Choose three.)

A. Fragmentation is a mechanism for dividing data where the volume of data is more than can be
transmitted in a single packet.

B. Fragmentation only applies when the upper layer protocol is TCP because TCP delivers a continuous
stream of data that must be fragmented.

C. The fragment size is determined by the MTU size of the network interface layer.

D. Fragmentation is a mechanism for dividing a class of IP addresses to allow more efficient use of the
address space.

E. Fragmentation occurs, when necessary, at each router a packet passes through based on the MTU for
the interface.

F. The fragment size always remains constant for a packet across all networks through which the packet
passes.

Answer: A,C,E

QUESTION NO: 167

Given:

host name IP address MAC address

host1 192.40.62.10 8:0:20:75:6e:7d

Which command puts a valid entry in the ARP table for workstation host1?

A. arp 8:0:20:75:6e:7d 192.40.62.10

B. arp -s host1 8:0:20:75:6e:7d

C. arp -s 192.40.62.10
D. arp -d host1 192.40.62.10

E. arp -a host1

Answer: B

QUESTION NO: 168

While using telnet, which two protocols are involved in peer-to-peer communication? (Choose two.)

A. RPC

B. IP

C. TCP

D. ICMP

E. UDP

Answer: B,C

QUESTION NO: 169

You have just installed a Solaris system with only one network interface in addition to the loopback
interface. By default, which process is started at boot on this system?

A. in.routed -s

B. in.rdisc -r

C. routed -s

D. in.rdisc -s
E. rdisc -r

Answer: D

QUESTION NO: 170

Which two commands can be used to display information about currently configured network
interfaces? (Choose two.)

A. netstat -n

B. netstat -s

C. netstat -i

D. ifconfig up

E. ifconfig -a

Answer: C,E

QUESTION NO: 171

Which two commands can be used to configure and enable a virtual interface? (Choose two.)

A. ifconfig hme0:1 146.32.1.100 virtual

B. ifconfig hme0 addif 146.32.1.100 up

C. ifconfig hme0:1 plumb 146.32.1.100 up

D. ifconfig hme0:1 add 146.32.1.100

E. ifconfig hme0 plumb 146.32.1.100 up

F. ifconfig hme0 146.32.1.100 up

Answer: B,C

QUESTION NO: 172

The IP address of an NTP stratum 4 server is 192.168.30.30. What entry in this server's NTP
configuration file indicates undisciplined local clock usage?

A. server 127.127.1.0 local

B. server 192.168.30.30 local

C. server 192.168.30.30

D. server 127.127.1.0 prefer

Answer: D

QUESTION NO: 173

With IPv6 addresses, a Format Prefix (FP) is used to identify the various types of IPv6 addresses. What is
the FP of a link-local unicast address?

A. FEC

B. FEA

C. 001

D. FE8

E. FF
Answer: D

QUESTION NO: 174

Which daemon is responsible for default route advertisements?

A. in.routed

B. routed

C. rdisc

D. in.rdisc

Answer: D

QUESTION NO: 175

Which two commands can be used to configure and enable a virtual interface? (Choose two.)

A. ifconfig hme0 plumb 146.32.1.100 up

B. ifconfig hme0:1 146.32.1.100 virtual

C. ifconfig hme0 addif 146.32.1.100 up

D. ifconfig hme0:1 plumb 146.32.1.100 up

E. ifconfig hme0 146.32.1.100 up

F. ifconfig hme0:1 add 146.32.1.100

Answer: C,D

QUESTION NO: 176

Which protocol does IPv6 use to discover MAC addresses?

A. Network Detection Protocol

B. Auto Configuration Protocol

C. Address Resolution Protocol

D. Neighbor Discovery Protocol

Answer: D

QUESTION NO: 177

Which three netmasks are valid Class B contiguous subnet masks? (Choose three.)

A. 255.255.255.32

B. 255.252.0.0

C. 255.255.255.128

D. 255.255.252.0

E. 255.255.255.0

F. 255.255.64.0

Answer: C,D,E
QUESTION NO: 178

Which two statements about jabbers are true? (Choose two.)

A. Jabbers are a normal phenomenon in a network, and there is no reason to worry about their
occurrence.

B. Faulty sending hardware or software might be the reason for jabbers.

C. Jabbers are frames whose Ethernet headers are malformed.

D. Jabbers are frames that are too short.

E. Jabbers are automatically discarded by the receiver.

F. Jabbers are caused by late collisions.

Answer: B,E

QUESTION NO: 179

Which two protocols are used by the ping command? (Choose two.)

A. TCP

B. UDP

C. IP

D. ICMP

Answer: C,D
QUESTION NO: 180

Which function does IP perform?

A. provides reliable delivery

B. chooses the route a packet will take

C. monitors and controls network devices

D. assembles data frames

Answer: B

QUESTION NO: 181

You have a DHCP client on network 192.200.51.0. The DHCP server has the DHCP data in the /var/dhcp
directory. The datastore format is ASCII. What is the full default path name of the file containing the IP
address pool for the Solaris 9 client?

A. /etc/inet/dhcp/192_200_51_0

B. /var/dhcp/SUNWfiles1_192_200_51_0

C. /var/dhcp/192_200_51_0

D. /var/dhcp/SUNWfiles1.192.200.51.0

Answer: B

QUESTION NO: 182

A network administrator configured an NTP server and an NTP client, but the client is refusing to
synchronize with the server. The client and server clocks have drifted too much for the xntpd daemon to
align them, and for the NTP protocol to synchronize them. Which two tools will synchronize the two
systems? (Choose two.)

A. ntpdate

B. zdate

C. syncdate

D. ntptrace

E. rdate

Answer: A,E

QUESTION NO: 183

Following a collision during normal Ethernet communication, what type of backoff technique is used to
calculate a random period of time to prevent the colliding systems from colliding again when
transmitting?

A. extraneous

B. exponential

C. exhaustive

D. extracted

E. extensive

Answer: B
QUESTION NO: 184

Which layer of the TCP/IP five-layer model contains UDP?

A. Transport Layer

B. Application Layer

C. Hardware Layer

D. Network Interface Layer

E. Internet Layer

Answer: A

QUESTION NO: 185 CORRECT TEXT

What is the full path name of the file which contains the clock type of an NTP server? Answer:

Answer: /ETC/INET/NTP.CONF

QUESTION NO: 186

The IP address of an NTP stratum 4 server is 192.168.30.30. What entry in this server's NTP
configuration file indicates undisciplined local clock usage?

A. server 192.168.30.30 local

B. server 127.127.1.0 prefer

C. server 192.168.30.30
D. server 127.127.1.0 local

Answer: B

QUESTION NO: 187

You have created an IPv6 tunnel between two hosts. Which two statements are true about tunnelling?
(Choose two.)

A. Tunnelled traffic is always TCP or UDP in IPv6.

B. The IP header of the datagram that has encapsulated the tunnelled data contains the source address
of the tunnel.

C. IPv6 Solaris tunnelling always involves an IP datagram encapsulating an IP datagram.

D. Tunnelled traffic is always encrypted.

E. The tunnel source IP address is always the same as the source IP address in the IP header of the
tunnelled (encapsulated) IP datagram.

Answer: B,C

QUESTION NO: 188

Which two are necessary requirements for IP Multipathing (IPMP)? (Choose two.)

A. a minimum of three physical interfaces available on the system

B. Solaris 8 10/00 or later releases

C. OBP parameter local-mac-address? set to true

D. /etc/hostname.interface files must contain the multipathing group and test address configuration.
E. in.mpathd must be enabled in /etc/inetd.conf

Answer: B,C

QUESTION NO: 189

With IPv6 addresses, a Format Prefix (FP) is used to identify the various types of IPv6 addresses. What is
the FP of a link-local unicast address?

A. FEC

B. FE8

C. 001

D. FEA

E. FF

Answer: B

QUESTION NO: 190

TCP segments are being routed in IP datagrams. When will a destination peer receive TCP segments that
are out of order?

A. when the IP datagrams that carry the TCP data are fragmented

B. when the TCP segments are corrupt

C. when the IP datagrams arrive out of order at the destination end

D. when the IP datagrams are corrupt

E. when the segments are transmitted out of order

Answer: C

QUESTION NO: 191

A DHCP server has an IP address of 192.2.9.92.

A DNS server has an IP address of 192.10.4.94.

The DNS server process is running in debug mode.

Given the debug output:

datagram from [192.2.9.92].32883, fd 26, len 44

req: nlookup(dhcp-pge-test.one.edu) id 19496 type=1 class=1

req: found 'dhcp-pge-test.one.edu' as 'one.edu' (cname=0)

ns_req: answer -> [192.2.9.92].32883 fd=26 id=19496 size=98 rc=3

datagram from [192.2.9.92].32884, fd 26, len 36

req: nlookup(dhcp-pge-test) id 19497 type=1 class=1

req: missed 'dhcp-pge-test) as '' (cname=0)

What does the debug output indicate?

A. The DNS server has updated its zone files with the IP address of the DHCP server.

B. Dynamic DNS is NOT currently configured on the DHCP server.

C. The DNS server has received a forwarded request from another DNS server.
D. The DNS server finds that the requested host name is NOT available for use in the domain.

Answer: D

QUESTION NO: 192

What can you do to permanently set parameters for the hme interface module so that they are
automatically configured on system boot?

A. define parameters in /kernel/drv/hme.cfg

B. define parameters in /etc/hostname.hme0

C. add commands that define the settings to a startup script in /etc/rc2.d

D. add commands that define the settings to /etc/netconfig

Answer: C

QUESTION NO: 193

When a system boots, which file configures Ethernet network interfaces?

A. /etc/default/netmasks

B. /etc/ifconfig.conf

C. /etc/inittab

D. /etc/rcS.d/S30network.sh

E. /etc/init.d/S30network.sh
Answer: D

QUESTION NO: 194

You have configured an IPv6 router which is having problems routing correctly to a default router
connected to the Internet. You need to investigate the machine's routing table and check that the
default route is in place. You also need to check the ARP cache to see whether the MAC address of the
default router has been learned. Which two commands enable you to perform these tasks? (Choose
two.)

A. arp -n

B. ifconfig -a

C. netstat -m

D. netstat -r

E. netstat -pn

Answer: D,E

QUESTION NO: 195

When must a local host try to route through an intermediary host to reach a remote host?

A. when the local host IP address was obtained using RARP

B. when the network address of the remote host differs from the network address of the local host

C. when the remote host is NOT in the ARP cache

D. when the routing table on the local host has been updated by RIP
Answer: B

QUESTION NO: 196

Which three monitoring tools are available for NTP? (Choose three.)

A. ntpq

B. ntpdebug

C. xntpdc

D. xntptrace

E. ntptrace

Answer: A,C,E

QUESTION NO: 197

A workstation does not have access to the 200.20.50.0 network. A system administrator needs to enable
access to a host at IP address 200.20.50.100. Other hosts on the same network must remain
inaccessible. Which command accomplishes this?

A. route add host 200.20.50.100 myrouter 1

B. netstat -a 200.20.50.100 200.20.50.0

C. route add myrouter 200.20.50.100 0

D. ifconfig -a qfe2 200.20.50.100 broadcast 200.20.50.255

E. route add net 200.20.50.100 myrouter 1

Answer: A

QUESTION NO: 198

Which statement about the in.rarpd daemon is true?

A. in.rarpd is started if the host is configured as a boot server.

B. in.rarpd is started whenever the system enters run level 3.

C. in.rarpd is started by inetd on demand.

D. The arp kernel module receives RARP request packets, starts in.rarpd, and passes the frames to
in.rarpd.

Answer: A

QUESTION NO: 199

Which command is used to start up the NTP daemon?

A. /etc/init.d/xntpd start

B. /etc/init.d/xntp start

C. /etc/init.d/ntpd start

D. /etc/init.d/ntp start

Answer: A
QUESTION NO: 200

Which three fields can be components of an IP datagram header? (Choose three.)

A. source IP address

B. destination IP address

C. transport protocol type

D. source MAC address

E. destination port number

Answer: A,B,C

QUESTION NO: 201 CORRECT TEXT

What is the full path name of the NTP client configuration template file? Answer:

Answer: /ETC/INET/NTP.CLIENT

QUESTION NO: 202

Which three statements about Classless Interdomain Routing (CIDR) are true? (Choose three.)

A. CIDR involves combining two or more contiguous address ranges.

B. CIDR uses netmasks to create network prefixes.

C. CIDR is also referred to as "supernetting."

D. CIDR applies to address spaces inside an organization only.

E. CIDR can only be applied to Class C network addresses.

Answer: A,B,C

QUESTION NO: 203

An unauthorized administrator has recently made some changes to your server. As a result, the server is
using ARP to attempt to reach hosts on a different subnetwork. Which file has been erroneously
modified?

A. /etc/inetd.conf

B. /etc/hosts

C. /etc/netmasks

D. /etc/init.d/inetinit

E. /etc/netgroup

F. /etc/services

Answer: C

QUESTION NO: 204

The ping command uses which protocol?

A. ICMP encapsulated in IP

B. ICMP encapsulated in UDP

C. ICMP encapsulated directly in an Ethernet frame

D. TCP encapsulated in IP

E. UDP encapsulated in IP

Answer: A

QUESTION NO: 205

A network administrator has correctly configured a DHCP server which is serving JumpStart and non-
JumpStart clients. One of the DHCP clients is asking only for an IP address, but NOT for any other
parameters such as subnet mask, router, host name, and encapsulated vendor options.

A variable must be modified in the /etc/default/dhcpagent file on the client to configure the DHCP
client's dhcpagent to request additional networking information from the DHCP server.

Which variable must be modified?

A. PARAM_REQUEST_ROWS

B. PARAM_REQUEST_LIST

C. PARAM_REQUEST_ADDRESS

D. PARAM_REQUEST_NETWORKING

E. PARAM_REQUEST_

Answer: B

QUESTION NO: 206

Which command displays the configuration of an hme0 network interface?

A. ndd /dev/hme0 \?

B. ndd hme0 \?

C. ifconfig hme0

D. ifconfig /dev/hme0

Answer: C

QUESTION NO: 207

What is a site local address?

A. a class D IPv4 address

B. an IPv6 address that will NOT be forwarded onto the Internet

C. an IPv6 address that will NOT be forwarded by a router

D. an IPv4 address given by a DHCP server on the same subnetwork

E. an IPv4 compatible IPv6 address

Answer: B

QUESTION NO: 208

Which two are benefits of IPv6? (Choose two.)

A. eliminates broadcast traffic

B. smaller addresses

C. more efficient routing

D. smaller routing tables

E. faster ARP/RARP

Answer: A,C

QUESTION NO: 209

Which protocol supports Classless Interdomain Routing (CIDR)?

A. Border Gateway Protocol

B. Router Discovery Protocol

C. External Gateway Protocol

D. Internet Control Message Protocol

E. Interior Gateway Protocol

Answer: A

QUESTION NO: 210

Which three commands or daemons update the routing table? (Choose three.)

A. in.rdisc

B. netstat
C. arp

D. arpd

E. in.routed

F. route

Answer: A,E,F

QUESTION NO: 211

Given the snoop trace that was run for three minutes:

sys10 -> sys4 NTPclient (Fri May10 14:45:02 2002)

sys4 -> sys10 NTPserver (Fri May 10 14:44:37 2002)

sys10 -> sys4 NTPclient (Fri May 10 14:46:06 2002)

sys4 -> sys10 NTPserver (Fri May 10 14:45:43 2002)

sys10 -> sys4 NTPclient (Fri May 10 14:47:10 2002)

sys4 -> sys10 NTPserver (Fri May 10 14:46:47 2002)

What is a reason that the NTP client has NOT changed its time?

A. The NTP client needs to receive more updates from its server.

B. The NTP client daemon process is NOT running.

C. The NTP server daemon process is NOT running.

D. The NTP client is configured as a broadcast client.

Answer: A

QUESTION NO: 212

Given the current origin is gvon.com, which two zone file lines correctly delegate the domain
training.gvon.com. to a server called centauri.gvon.com.? (Choose two.)

A. training.gvon.com. in NS centauri.gvon.com.

B. gvon.com in NS centauri.gvon.com.

C. centauri.gvon.com. in NS gvon.com.

D. training in NS centauri.gvon.com.

E. gvon in NS centauri.gvon.com.

F. training. in NS centauri.gvon.com.

Answer: A,D

QUESTION NO: 213 DRAG DROP

Click the Task button.

Place each TCP/IP protocol or standard on its corresponding layer of the TCP/IP model.
Answer: <m x1="42" x2="169" y1="22" y2="70" ss="0" a="0"></m><m x1="41" x2="167" y1="78"
y2="126" ss="0" a="1"></m><m x1="41" x2="168" y1="136" y2="182" ss="0" a="2"></m><m x1="40"
x2="167" y1="191" y2="237" ss="0" a="3"></m><m x1="42" x2="168" y1="248" y2="294" ss="0"
a="4"></m><m x1="262" x2="393" y1="23" y2="71" ss="1" a="0"></m><m x1="264" x2="393" y1="80"
y2="126" ss="1" a="1"></m><m x1="265" x2="393" y1="136" y2="183" ss="1" a="2"></m><m x1="265"
x2="392" y1="191" y2="239" ss="1" a="3"></m><m x1="264" x2="392" y1="247" y2="295" ss="1"
a="4"></m><c start="0" stop="2"></c><c start="1" stop="0"></c><c start="2" stop="4"></c><c
start="3" stop="3"></c><c start="4" stop="1"></c>

QUESTION NO: 214

A DNS server has MX records which indicate that there are three SMTP relays for the domain gvon.com.
A problem occurs, whereby other DNS servers make iterative queries for the MX records every time they
are queried by clients. Which two MX lines cause remote DNS servers to refuse to cache the MX record
for SMTP relay smtp.gvon.com? (Choose two.)

A. gvon.com. 0 in mx 5 smtp.gvon.com.

B. gvon.com. in mx 5 smtp.gvon.com.

C. gvon.com. 100 in mx 10 smtp.gvon.com.

D. gvon.com. 0 in mx 0 smtp.gvon.com.

E. gvon.com. mx 100 smtp.gvon.com.

Answer: A,D

QUESTION NO: 215

A system administrator is attempting to add a default router using the command:

route add default 192.20.20.1 0

You get the error message "Network is unreachable." The IP address of the host you are using is
192.20.20.10, and the router 192.20.20.1 is reachable using a "direct" route. The router 192.20.20.1 is
on the network in question and is a viable default router.

What causes the error message "Network is unreachable"?

A. You already have several default routers.

B. Default routers can only be added through a file at boot-up .

C. The metric of 0 should be 1.

D. You should act as the default router to your own network.

E. Your default router should be reachable indirectly.

Answer: C
QUESTION NO: 216 DRAG DROP

Click the Task button.

Place each LAN component next to its description.

Answer: <m x1="93" x2="175" y1="232" y2="263" ss="0" a="0"></m><m x1="183" x2="263" y1="234"
y2="264" ss="0" a="1"></m><m x1="272" x2="350" y1="233" y2="264" ss="0" a="2"></m><m x1="16"
x2="96" y1="73" y2="104" ss="1" a="0"></m><m x1="15" x2="94" y1="112" y2="144" ss="1"
a="1"></m><m x1="14" x2="95" y1="152" y2="184" ss="1" a="2"></m><c start="1" stop="0"></c><c
start="2" stop="1"></c><c start="0" stop="2"></c>

QUESTION NO: 217

Which two statements about the /etc/named.conf file are true? (Choose two.)

A. It informs in.named which zones it supports as a primary or secondary.

B. It allows nslookup to resolve queries.

C. It configures a primary with the addresses of secondary servers.

D. It informs a secondary server of the address of the primary.

Answer: A,D

QUESTION NO: 218

Which two statements about a service in the client-server model are true? (Choose two.)

A. A service is started only at system boot.

B. A service always occurs across a network link.

C. A service must be listed in /etc/services.

D. A service is accessed by a process.

E. A service is provided by a process.

Answer: D,E

QUESTION NO: 219

Which domain name is the uppermost in the branch of the DNS tree related to reverse lookups?

A. arpa

B. com

C. in-addr

D. net
Answer: A

QUESTION NO: 220

In the five-layer TCP/IP model, at which two layers does the client-server relationship function? (Choose
two.)

A. Internet Layer

B. Network Interface Layer

C. Hardware Layer

D. Application Layer

E. Transport Layer

Answer: D,E

QUESTION NO: 221

Which two commands can be used to configure and enable a virtual interface? (Choose two.)

A. ifconfig hme0 plumb 146.32.1.100 up

B. ifconfig hme0:1 146.32.1.100 virtual

C. ifconfig hme0 addif 146.32.1.100 up

D. ifconfig hme0:1 add 146.32.1.100

E. ifconfig hme0 146.32.1.100 up

F. ifconfig hme0:1 plumb 146.32.1.100 up

Answer: C,F

QUESTION NO: 222

What does the NTP term "stratum" refer to?

A. the reference clock

B. the time zone where an NTP server resides

C. the clock precision

D. the local undisciplined clock

E. the level of hierarchy in NTP

Answer: E

QUESTION NO: 223 DRAG DROP

Click the Task button.

Place each network component on the TCP/IP model layer at which it operates.
Answer: <m x1="26" x2="153" y1="48" y2="96" ss="0" a="0"></m><m x1="24" x2="152" y1="104"
y2="151" ss="0" a="1"></m><m x1="25" x2="152" y1="161" y2="207" ss="0" a="2"></m><m x1="25"
x2="153" y1="216" y2="262" ss="0" a="3"></m><m x1="218" x2="345" y1="49" y2="96" ss="1"
a="0"></m><m x1="217" x2="344" y1="103" y2="151" ss="1" a="1"></m><m x1="217" x2="345"
y1="162" y2="208" ss="1" a="2"></m><m x1="218" x2="344" y1="215" y2="265" ss="1" a="3"></m><c
start="0" stop="2"></c><c start="1" stop="1"></c><c start="2" stop="0"></c><c start="3"
stop="3"></c>

QUESTION NO: 224

You have just installed a Solaris system with only one network interface in addition to the loopback
interface. By default, which process is started at boot on this system?

A. in.rdisc -s

B. routed -s

C. in.routed -s

D. rdisc -r

E. in.rdisc -r
Answer: A

QUESTION NO: 225

The ping command uses which protocol?

A. ICMP encapsulated directly in an Ethernet frame

B. UDP encapsulated in IP

C. TCP encapsulated in IP

D. ICMP encapsulated in UDP

E. ICMP encapsulated in IP

Answer: E

QUESTION NO: 226

You are helping a junior network administrator configure and set up a tunnel, and need to ping the
remote end of the tunnel to ensure the tunnel will work.

Since the remote end of the tunnel can be pinged without a tunnel in place, the junior network
administrator asks why a tunnel needs to be created.

What are two reasons to create a tunnel? (Choose two.)

A. Tunnelling results in faster routing because the router has fewer headers to inspect.

B. Tunnelling allows for IPv6 networks to be routed over IPv4 network infrastructures.
C. Tunnelling allows for IPv6 datagrams to be routed within IPv4 datagrams.

D. Tunnelling ensures privacy of data through encryption.

E. Tunnelling allows Ethernet packets to be encapsulated in IPv6 packets.

Answer: B,C

QUESTION NO: 227

What can you do to permanently set parameters for the hme interface module so that they are
automatically configured on system boot?

A. define parameters in /kernel/drv/hme.cfg

B. add commands that define the settings to /etc/netconfig

C. define parameters in /etc/hostname.hme0

D. add commands that define the settings to a startup script in /etc/rc2.d

Answer: D

QUESTION NO: 228

The address 197.20.71.0 identifies a network that you want to identify with a name. Which file, if edited,
will identify the network address with a name?

A. /etc/hosts

B. /etc/inet/networks

C. /etc/networks.conf
D. /etc/default/networks.conf

E. /etc/inet/networks.conf

Answer: B

QUESTION NO: 229

Which Class C networks are described by the CIDR routing table entry 204.108.16.0/23?

A. 204.108.16.0 to 204.108.19.0

B. 204.108.16.0 only

C. 204.108.15.0 to 204.108.16.0

D. 204.108.16.0 to 204.108.17.0

Answer: D

QUESTION NO: 230

A router is refusing to forward IP packets, and snoop reveals that packets are arriving on its interfaces,
but it is refusing to forward packets and route them. What command verifies that the router is currently
configured (in the kernel) to forward IP packets?

A. ndd -set /dev/ip ip_forwarding 0

B. ndd -set /dev/ip ip_forwarding 1

C. ndd -get /dev/ip ip_forwarding

D. ndd -get ip-forwarding /dev/tcp

E. ndd -get /dev/udp ip-forward

Answer: C

QUESTION NO: 231

A server has a single hme Ethernet interface auto-configured with an IPv6 address. Which statement
about the configuration process is true?

A. The file /etc/hostname6.hme0 exists and contains an entry found in /etc/inet/ipnodes.

B. The file /etc/hostname6.hme0 exists and contains an entry found in /etc/inet/hosts.

C. The file /etc/hostname6.hme0 does NOT exist.

D. The file /etc/hostname6.hme0 exists and is empty.

Answer: D

QUESTION NO: 232

Which two can be achieved by configuring the /etc/gateways file? (Choose two.)

A. preventing routing processes such as RIP starting

B. adding additional indirect routes

C. adding a default route, preventing any routing daemon from starting

D. automatically adding static entries in the routing table when the system boots

Answer: B,D
QUESTION NO: 233

Which is the only DHCP lease type that allows for an IP address to be leased for a finite period of time?

A. dynamic

B. manual

C. static

D. automatic

E. bootp

Answer: A

QUESTION NO: 234

A printer is connected to the same subnet as your workstation. The printer is identified as:

host name IP address MAC address

printer1 192.204.200.12 8:0:20:21:38:6b

Which command allows your workstation to reply to ARP requests for the printer?

A. arp -p printer1 8:0:20:21:38:6b

B. rarp -s 192.204.200.12 8:0:20:21:38:6b

C. arp -s printer1 8:0:20:21:38:6b pub

D. netconfig -p 192.204.200.12 printer1

Answer: C

QUESTION NO: 235 CORRECT TEXT

What is the full default path name of the NTP configuration file? Answer:

Answer: /ETC/INET/NTP.CONF

QUESTION NO: 236

You have configured an IPv6 router which is having problems routing correctly to a default router
connected to the Internet. You need to investigate the machine's routing table and check that the
default route is in place. You also need to check the ARP cache to see whether the MAC address of the
default router has been learned. Which two commands enable you to perform these tasks? (Choose
two.)

A. netstat -pn

B. netstat -r

C. netstat -m

D. arp -n

E. ifconfig -a

Answer: A,B
QUESTION NO: 237

This message appears in a system's console window:

May 9 08:02:03 sys11 in.mpathd[475]: Failures cannot be detected on qfe0 as no IFF_NOFAILOVER

address is available

What does the message indicate?

A. The in.mpathd process must be restarted.

B. Interface qfe0 has failed, and an alternate interface in the same group is being used for application
traffic.

C. A test interface has not been defined.

D. A system reboot must be performed.

Answer: C

QUESTION NO: 238

Which three subnet masks are contiguous subnet masks for Class C addresses? (Choose three.)

A. 255.255.255.192

B. 255.255.255.64

C. 255.255.255.224

D. 255.255.255.240

E. 255.255.252.0
Answer: A,C,D

QUESTION NO: 239

In which mode is an Ethernet card configured to pass all Ethernet frames up the protocol stack
(inbound) regardless of the Ethernet frame's destination MAC address?

A. Point-to-Point

B. PointCard Mode

C. Profligate Mode

D. Prominent Mode

E. Promiscuous Mode

Answer: E

QUESTION NO: 240

Which command displays the configuration of an hme0 network interface?

A. ifconfig /dev/hme0

B. ndd /dev/hme0 \?

C. ndd hme0 \?

D. ifconfig hme0

Answer: D
QUESTION NO: 241

Click the Exhibit button.

Which logical network topology describes the configuration?

A. broadcast

B. fully connected

C. star

D. ring

E. bus

Answer: D

QUESTION NO: 242

The traceroute command shows routing paths to a given destination. What protocols are used by this
diagnostic tool?
A. TCP + IP

B. HTTP + IP

C. ICMP + IP

D. SNMP + IP

E. SNMP + TCP

Answer: C

QUESTION NO: 243

A network administrator has several clients unable to generate ARP requests, and the administrator
decides it is safe to use IP addresses assigned by DHCP servers.

What should the network administrator do to ensure that DHCP clients' dhcpagent daemons will accept
an IP address even though they are unable to generate an ARP request?

A. modify DHCP clients and disable RARP

B. ensure that the client interface is set to NOARP

C. set the IGNORE_FAILED_ARP variable to no

D. set the IGNORE_FAILED_ARP variable to yes

Answer: D

QUESTION NO: 244

A printer is connected to the same subnet as your workstation. The printer is identified as:

host name IP address MAC address

printer1 192.204.200.12 8:0:20:21:38:6b

Which command allows your workstation to reply to ARP requests for the printer?

A. netconfig -p 192.204.200.12 printer1

B. arp -p printer1 8:0:20:21:38:6b

C. rarp -s 192.204.200.12 8:0:20:21:38:6b

D. arp -s printer1 8:0:20:21:38:6b pub

Answer: D

QUESTION NO: 245

In the five-layer TCP/IP model, which protocol is contained in the same layer as IP?

A. ICMP

B. PPP

C. TCP

D. SNMP

E. UDP

Answer: A
QUESTION NO: 246

You are helping a junior network administrator configure and set up a tunnel, and need to ping the
remote end of the tunnel to ensure the tunnel will work.

Since the remote end of the tunnel can be pinged without a tunnel in place, the junior network
administrator asks why a tunnel needs to be created.

What are two reasons to create a tunnel? (Choose two.)

A. Tunnelling results in faster routing because the router has fewer headers to inspect.

B. Tunnelling allows Ethernet packets to be encapsulated in IPv6 packets.

C. Tunnelling allows for IPv6 datagrams to be routed within IPv4 datagrams.

D. Tunnelling allows for IPv6 networks to be routed over IPv4 network infrastructures.

E. Tunnelling ensures privacy of data through encryption.

Answer: C,D

QUESTION NO: 247

Which three statements about Classless Interdomain Routing (CIDR) are true? (Choose three.)

A. CIDR uses netmasks to create network prefixes.

B. CIDR is also referred to as "supernetting."

C. CIDR applies to address spaces inside an organization only.

D. CIDR can only be applied to Class C network addresses.

E. CIDR involves combining two or more contiguous address ranges.

Answer: A,B,E

QUESTION NO: 248

Which two commands display the contents of the ARP table? (Choose two.)

A. netstat -a

B. arp -s

C. ifconfig -a

D. arp -d

E. netstat -p

F. arp -a

Answer: E,F

QUESTION NO: 249

The interface hme0 has the wrong IP address. Which command re-establishes the correct address of
192.168.20.118, broadcast of 192.168.20.127, and netmask of 255.255.255.192?

A. ifconfig hme0 192.168.20.118 netmask 255.255.255.127 broadcast +

B. ifconfig hme0 192.168.20.118 netmask 192.168.20.127 broadcast +

C. ifconfig hme0 192.168.20.118 netmask 255.255.255.192 + broadcast

D. ifconfig hme0 192.168.20.118 netmask 255.255.255.192 broadcast +

E. ifconfig hme0 192.168.20.118 netmask 255.255.255.0 + broadcast

Answer: D

QUESTION NO: 250

What is the correct format for zone file record lines?

A. [name] [ttl] class record_type record_data

B. [ttl] [name] class record_type record_data

C. [DomainIP] [ttl] class record_type record_data

D. [servername] [ttl] class record_type record_data

Answer: A

QUESTION NO: 251

Which two fields are found in the /etc/netmasks file? (Choose two.)

A. netmask value

B. network number

C. netgroup name

D. domain name

E. network name
Answer: A,B

QUESTION NO: 252

Which command is used to start up the NTP daemon?

A. /etc/init.d/xntp start

B. /etc/init.d/ntpd start

C. /etc/init.d/xntpd start

D. /etc/init.d/ntp start

Answer: C

QUESTION NO: 253

What is the official international standard for time?

A. Universal Time Coordinated

B. Greenwich Mean Time

C. Sidereal Time

D. Eastern Standard Time

Answer: A
QUESTION NO: 254

A DNS server (the primary) for domainshop.co.uk is having problems delegating authority and
responsibility for the subdomain sales.domainshop.co.uk. Investigation reveals that the delegation is not
functioning. The current origin is domainshop.co.uk.

Given the lines from the domainshop.co.uk zone file:

sales. in ns centauri.domainshop.co.uk.

centauri.domainshop.co.uk in a 194.168.85.2

Which two errors are present? (Choose two.)

A. The name field of the second line should be terminated with a dot (.).

B. The ns should be NS and, therefore, in uppercase.

C. The name field sales should NOT be terminated with a dot (.).

D. The two lines must be separated by a blank line.

E. The file lacks a PTR record for the NS centauri.domainshop.co.uk.

Answer: A,C

QUESTION NO: 255

A server has a single hme Ethernet interface auto-configured with an IPv6 address. Which statement
about the configuration process is true?

A. The file /etc/hostname6.hme0 exists and contains an entry found in /etc/inet/hosts.

B. The file /etc/hostname6.hme0 does NOT exist.

C. The file /etc/hostname6.hme0 exists and contains an entry found in /etc/inet/ipnodes.

D. The file /etc/hostname6.hme0 exists and is empty.

Answer: D

QUESTION NO: 256 CORRECT TEXT

What is the length, in bits, of the network interface-specific identifier (VID) of the Ethernet address?
Answer:

Answer: 24

QUESTION NO: 257

What is the purpose of RARP?

A. It maps a 48-bit Ethernet address to a 32-bit IP address.

B. It maps a 128-bit IP address to a 48-bit Ethernet address.

C. It maps a 48-bit IP address to a 32-bit Ethernet address.

D. It maps a 32-bit Ethernet address to a 128-bit IP address.

E. It maps a 32-bit IP address to a 48-bit Ethernet address.

Answer: A
QUESTION NO: 258

Which three are components of a subnetted IP address? (Choose three.)

A. subnet number

B. Ethernet address

C. host number

D. netgroup number

E. broadcast address

F. network number

Answer: A,C,F

QUESTION NO: 259

Which layer of the TCP/IP five-layer model contains UDP?

A. Transport Layer

B. Hardware Layer

C. Network Interface Layer

D. Internet Layer

E. Application Layer

Answer: A
QUESTION NO: 260

Following a collision during normal Ethernet communication, what type of backoff technique is used to
calculate a random period of time to prevent the colliding systems from colliding again when
transmitting?

A. exhaustive

B. exponential

C. extracted

D. extensive

E. extraneous

Answer: B

QUESTION NO: 261

What command obtains the link_speed for the hme0 interface?

A. ifconfig -get link_speed hme

B. ndd /dev/hme0 link_speed

C. ndd /dev/hme link_speed

D. ifconfig -get link_speed hme0

Answer: C

QUESTION NO: 262 DRAG DROP

Click the Task button.

Place each DHCP packet type on its DHCP client-server interaction step.

Answer: <m x1="19" x2="105" y1="20" y2="50" ss="0" a="0"></m><m x1="19" x2="107" y1="86"
y2="121" ss="0" a="1"></m><m x1="17" x2="107" y1="156" y2="186" ss="0" a="2"></m><m x1="18"
x2="106" y1="225" y2="255" ss="0" a="3"></m><m x1="139" x2="226" y1="226" y2="257" ss="1"
a="0"></m><m x1="139" x2="225" y1="106" y2="138" ss="1" a="1"></m><m x1="332" x2="419"
y1="162" y2="193" ss="1" a="2"></m><m x1="332" x2="418" y1="297" y2="332" ss="1" a="3"></m><c
start="2" stop="1"></c><c start="1" stop="2"></c><c start="3" stop="0"></c><c start="0"
stop="3"></c>

QUESTION NO: 263

Which two are functions of the dhcpagent process? (Choose two.)

A. releases IP addresses or negotiates lease renewals

B. caches the information for use in configuration of the interface

C. responds to DHCPDISCOVER packets

D. updates the DHCP datastores

E. manages the IP address space of connected networks

Answer: A,B

QUESTION NO: 264

Where does the NTP daemon send its error information by default?

A. to the syslog facility

B. directly to the controlling terminal

C. The daemon does not report error information by default.

D. to an internal buffer from where it can be queried with an additional tool

Answer: A

QUESTION NO: 265

Which two are reasons to use Classless Interdomain Routing (CIDR)? (Choose two.)

A. to deal with the shortage of Class B IP addresses

B. to reduce the number of routers required in a network

C. to make maximum use of entries in the ARP cache

D. to support IPv4 and IPv6 on the same network

E. to reduce the size of routing tables

Answer: A,E

QUESTION NO: 266

Which two commands can be used to display information about currently configured network
interfaces? (Choose two.)

A. netstat -n

B. netstat -i

C. netstat -s

D. ifconfig -a

E. ifconfig up

Answer: B,D

QUESTION NO: 267

Click the Exhibit button.

The if_mpadm -d qfe1 command is executed.

What is the name of the interface that will be used to pass network traffic?
A. hme0

B. qfe0
C. qfe0:2

D. qfe1:1

Answer: C

QUESTION NO: 268

What is the purpose of the Preamble field of a 10 mbps Ethernet frame?

A. It is used to direct the data to the appropriate upper layer protocol for processing.

B. It is used for interface synchronization.

C. It is used for error detection.

D. It is used to determine the origin of the data.

Answer: B

QUESTION NO: 269

A DNS server (the primary) for domainshop.co.uk is having problems delegating authority and
responsibility for the subdomain sales.domainshop.co.uk. Investigation reveals that the delegation is not
functioning. The current origin is domainshop.co.uk.

Given the lines from the domainshop.co.uk zone file:

sales. in ns centauri.domainshop.co.uk.

centauri.domainshop.co.uk in a 194.168.85.2
Which two errors are present? (Choose two.)

A. The file lacks a PTR record for the NS centauri.domainshop.co.uk.

B. The name field of the second line should be terminated with a dot (.).

C. The two lines must be separated by a blank line.

D. The name field sales should NOT be terminated with a dot (.).

E. The ns should be NS and, therefore, in uppercase.

Answer: B,D

QUESTION NO: 270

A host's IPv6 link-local unicast address is based on the host's Ethernet address. The beginning of the
address is prefixed by a specific Format Prefix (FP) value to indicate that the address is a link-local
address. In addition, a 16-bit code is inserted in 64-bit Interface ID portion of the IPv6 address to enable
a 48-bit Ethernet address to become 64 bits in length.

Which value represents the 16-bit code?

A. FFFE

B. FEC0

C. FE80

D. FFFF

E. FFEE

Answer: A
QUESTION NO: 271

A router is refusing to forward IP packets, and snoop reveals that packets are arriving on its interfaces,
but it is refusing to forward packets and route them. What command verifies that the router is currently
configured (in the kernel) to forward IP packets?

A. ndd -get /dev/ip ip_forwarding

B. ndd -set /dev/ip ip_forwarding 1

C. ndd -set /dev/ip ip_forwarding 0

D. ndd -get /dev/udp ip-forward

E. ndd -get ip-forwarding /dev/tcp

Answer: A

QUESTION NO: 272

What is a site local address?

A. an IPv6 address that will NOT be forwarded by a router

B. an IPv4 compatible IPv6 address

C. an IPv6 address that will NOT be forwarded onto the Internet

D. a class D IPv4 address

E. an IPv4 address given by a DHCP server on the same subnetwork

Answer: C
QUESTION NO: 273

Which is the meaning of the DEPRECATED interface flag?

A. The interface will ignore any offlining attempts by the if_mpadm command.

B. It is used by in.mpathd to detect test addresses.

C. The IP address will not be used by applications as source address for outbound packets.

D. The IP address will not fail over in case of a failure of the corresponding physical interface.

Answer: C

QUESTION NO: 274

In the five-layer TCP/IP model, at which two layers does the client-server relationship function? (Choose
two.)

A. Application Layer

B. Hardware Layer

C. Internet Layer

D. Network Interface Layer

E. Transport Layer

Answer: A,E
QUESTION NO: 275

A DHCP server has an IP address of 192.2.9.92.

A DNS server has an IP address of 192.10.4.94.

The DNS server process is running in debug mode.

Given the debug output:

datagram from [192.2.9.92].32883, fd 26, len 44

req: nlookup(dhcp-pge-test.one.edu) id 19496 type=1 class=1

req: found 'dhcp-pge-test.one.edu' as 'one.edu' (cname=0)

ns_req: answer -> [192.2.9.92].32883 fd=26 id=19496 size=98 rc=3

datagram from [192.2.9.92].32884, fd 26, len 36

req: nlookup(dhcp-pge-test) id 19497 type=1 class=1

req: missed 'dhcp-pge-test) as '' (cname=0)

What does the debug output indicate?

A. Dynamic DNS is NOT currently configured on the DHCP server.

B. The DNS server has received a forwarded request from another DNS server.

C. The DNS server finds that the requested host name is NOT available for use in the domain.

D. The DNS server has updated its zone files with the IP address of the DHCP server.

Answer: C
QUESTION NO: 276

A DHCP server has an IP address of 192.2.9.92.

A DNS server has an IP address of 192.10.4.94.

The DNS server process is running in debug mode.

Given the debug output:

datagram from [192.2.9.92].32883, fd 26, len 44

req: nlookup(dhcp-pge-test.one.edu) id 19496 type=1 class=1

req: found 'dhcp-pge-test.one.edu' as 'one.edu' (cname=0)

ns_req: answer -> [192.2.9.92].32883 fd=26 id=19496 size=98 rc=3

datagram from [192.2.9.92].32884, fd 26, len 36

req: nlookup(dhcp-pge-test) id 19497 type=1 class=1

req: missed 'dhcp-pge-test) as '' (cname=0)

What does the debug output indicate?

A. The DNS server has updated its zone files with the IP address of the DHCP server.

B. The DNS server has received a forwarded request from another DNS server.

C. The DNS server finds that the requested host name is NOT available for use in the domain.

D. Dynamic DNS is NOT currently configured on the DHCP server.

Answer: C
QUESTION NO: 277

Given:

route add host lion tiger 1

Which two statements are true? (Choose two.)

A. The command indicates that lion is the only intermediate host on this route.

B. The command indicates that tiger is an intermediate host on this route.

C. The command adds a static route to the routing table.

D. The command causes hosts tiger and lion to update their routing tables.

E. All hosts on the lion network could be reached as a result of the command.

Answer: B,C

QUESTION NO: 278

What command obtains the link_speed for the hme0 interface?

A. ifconfig -get link_speed hme

B. ndd /dev/hme0 link_speed

C. ndd /dev/hme link_speed

D. ifconfig -get link_speed hme0

Answer: C
QUESTION NO: 279

Which two statements describe the function of a bridge? (Choose two.)

A. It forwards packets between networks.

B. It connects two or more hosts to a hub.

C. It filters packets by MAC addresses.

D. It connects two or more network segments.

Answer: C,D

QUESTION NO: 280

What can you do to permanently set parameters for the hme interface module so that they are
automatically configured on system boot?

A. define parameters in /etc/hostname.hme0

B. add commands that define the settings to a startup script in /etc/rc2.d

C. add commands that define the settings to /etc/netconfig

D. define parameters in /kernel/drv/hme.cfg

Answer: B

QUESTION NO: 281

Which two commands allow you to define a DHCP symbol? (Choose two.)

A. dhcpinfo

B. pntadm

C. dhtadm

D. dhcpmgr

Answer: C,D

QUESTION NO: 282

What is the purpose of the Preamble field of a 10 mbps Ethernet frame?

A. It is used to determine the origin of the data.

B. It is used for interface synchronization.

C. It is used for error detection.

D. It is used to direct the data to the appropriate upper layer protocol for processing.

Answer: B

QUESTION NO: 283

Which command can be used to query the NTP server server1 for the current time of day, and can set
the time and date on the system's clock?

A. ntpdate server1
B. date -p ntp server1

C. ntptrace server1

D. ntpq server1

Answer: A

QUESTION NO: 284

A network administrator configured an NTP server and an NTP client, but the client is refusing to
synchronize with the server. The client and server clocks have drifted too much for the xntpd daemon to
align them, and for the NTP protocol to synchronize them. Which two tools will synchronize the two
systems? (Choose two.)

A. zdate

B. syncdate

C. ntpdate

D. rdate

E. ntptrace

Answer: C,D

QUESTION NO: 285

You are helping a junior network administrator configure and set up a tunnel, and need to ping the
remote end of the tunnel to ensure the tunnel will work.
Since the remote end of the tunnel can be pinged without a tunnel in place, the junior network
administrator asks why a tunnel needs to be created.

What are two reasons to create a tunnel? (Choose two.)

A. Tunnelling results in faster routing because the router has fewer headers to inspect.

B. Tunnelling allows Ethernet packets to be encapsulated in IPv6 packets.

C. Tunnelling ensures privacy of data through encryption.

D. Tunnelling allows for IPv6 datagrams to be routed within IPv4 datagrams.

E. Tunnelling allows for IPv6 networks to be routed over IPv4 network infrastructures.

Answer: D,E

QUESTION NO: 286

A network administrator has correctly configured a DHCP server which is serving JumpStart and non-
JumpStart clients. One of the DHCP clients is asking only for an IP address, but NOT for any other
parameters such as subnet mask, router, host name, and encapsulated vendor options.

A variable must be modified in the /etc/default/dhcpagent file on the client to configure the DHCP
client's dhcpagent to request additional networking information from the DHCP server.

Which variable must be modified?

A. PARAM_REQUEST_LIST

B. PARAM_REQUEST_ADDRESS

C. PARAM_REQUEST_ROWS
D. PARAM_REQUEST_NETWORKING

E. PARAM_REQUEST_

Answer: A

QUESTION NO: 287 CORRECT TEXT

What is the full path name of the NTP server configuration template file? Answer:

Answer: /ETC/INET/NTP.SERVER

QUESTION NO: 288

Click the Exhibit button.

Which logical network topology describes the configuration?

A. fully connected

B. star

C. bus

D. ring

E. broadcast

Answer: D

QUESTION NO: 289

Which statement about the in.rarpd daemon is true?

A. in.rarpd is started whenever the system enters run level 3.

B. in.rarpd is started if the host is configured as a boot server.

C. in.rarpd is started by inetd on demand.

D. The arp kernel module receives RARP request packets, starts in.rarpd, and passes the frames to
in.rarpd.

Answer: B

QUESTION NO: 290

Which file is read by the in.rarpd daemon?

A. /etc/inetd.conf

B. /etc/netgroup
C. /etc/inet/rarp.conf

D. /etc/netmasks

E. /etc/ethers

Answer: E

QUESTION NO: 291

Which two statements about jabbers are true? (Choose two.)

A. Jabbers are automatically discarded by the receiver.

B. Jabbers are frames whose Ethernet headers are malformed.

C. Jabbers are caused by late collisions.

D. Jabbers are a normal phenomenon in a network, and there is no reason to worry about their
occurrence.

E. Faulty sending hardware or software might be the reason for jabbers.

F. Jabbers are frames that are too short.

Answer: A,E

QUESTION NO: 292

Which three commands or daemons update the routing table? (Choose three.)

A. netstat

B. in.rdisc
C. route

D. arp

E. in.routed

F. arpd

Answer: B,C,E

QUESTION NO: 293

Given files containing relevant data and a server with a single hme Ethernet interface, which three files
are used to configure the Ethernet interface at system boot? (Choose three.)

A. /etc/inet/hosts

B. /etc/hostname.hme0

C. /etc/inet/netmasks

D. /etc/nodename

E. /etc/inet/networks

Answer: A,B,C

QUESTION NO: 294

You have a DHCP client on network 192.200.51.0. The DHCP server has the DHCP data in the /var/dhcp
directory. The datastore format is ASCII. What is the full default path name of the file containing the IP
address pool for the Solaris 9 client?

A. /etc/inet/dhcp/192_200_51_0
B. /var/dhcp/SUNWfiles1_192_200_51_0

C. /var/dhcp/192_200_51_0

D. /var/dhcp/SUNWfiles1.192.200.51.0

Answer: B

QUESTION NO: 295

Which file contains the definitions for the default and vendor-specific DHCP options and symbols?

A. /etc/default/dhcp

B. /var/dhcp/inittab

C. /etc/default/dhcpagent

D. /etc/dhcp/inittab

Answer: D

QUESTION NO: 296

Which network device type can translate between different Network Interface Layer protocols?

A. bridge

B. network interface card

C. hub

D. repeater
Answer: A

QUESTION NO: 297

Which is the minimum layer reached by all IPv6 datagrams when passing through a router?

A. Application Layer

B. Internet Layer

C. Network Interface Layer

D. Physical Layer

E. Transport Layer

Answer: B

QUESTION NO: 298

A DNS server is configured as a secondary server and successfully synchronizes with the primary server
when the secondary server is first started. A zone file on the primary server is updated but the
secondary server fails to synchronize. The secondary server is rebooted but this fails to help. Which
failure caused this problem?

A. failure to update the time stamp of the updated zone file

B. failure to update the SOA ttl number of the updated zone file

C. failure to update the serial number of the updated zone file

D. failure to update the NS record of the updated zone file

Answer: C

QUESTION NO: 299

A DNS server is not responding to a DNS client's requests. Which four commands can be used in
debugging DNS? (Choose four.)

A. dig

B. pkill -INT in.named

C. pkill -USR1 in.named

D. nslookup

E. pkill -INT in.inetd

F. pkill -INT inetd

Answer: A,B,C,D

QUESTION NO: 300

What is the purpose of RARP?

A. It maps a 32-bit IP address to a 48-bit Ethernet address.

B. It maps a 32-bit Ethernet address to a 128-bit IP address.

C. It maps a 128-bit IP address to a 48-bit Ethernet address.

D. It maps a 48-bit Ethernet address to a 32-bit IP address.

E. It maps a 48-bit IP address to a 32-bit Ethernet address.

Answer: D

QUESTION NO: 301

Given files containing relevant data and a server with a single hme Ethernet interface, which three files
are used to configure the Ethernet interface at system boot? (Choose three.)

A. /etc/hostname.hme0

B. /etc/inet/networks

C. /etc/inet/hosts

D. /etc/nodename

E. /etc/inet/netmasks

Answer: A,C,E

QUESTION NO: 302

A system administrator is attempting to configure the virtual interface:

hme0:500

by running the command:

# ifconfig hme0:500 plumb

but the system administrator receives the error:

ifconfig: plumb: SIOCLIFADDIF: hme0:500 no such interface

Solaris 9 supports up to 8192 virtual interfaces associated with a given physical interface.

What is causing the problem?

A. By default, only quad card interfaces support virtual interfaces.

B. The ifconfig syntax is incorrect.

C. By default, the kernel only supports up to 256 virtual interfaces.

D. The system administrator needs to reboot.

Answer: C

QUESTION NO: 303

A system administrator is attempting to configure the virtual interface:

hme0:500

by running the command:

# ifconfig hme0:500 plumb

but the system administrator receives the error:

ifconfig: plumb: SIOCLIFADDIF: hme0:500 no such interface

Solaris 9 supports up to 8192 virtual interfaces associated with a given physical interface.

What is causing the problem?

A. The system administrator needs to reboot.

B. By default, only quad card interfaces support virtual interfaces.

C. By default, the kernel only supports up to 256 virtual interfaces.

D. The ifconfig syntax is incorrect.

Answer: C

QUESTION NO: 304

Given the routes are to the same destination, which route does RIP configure for use?

A. a route through three intermediary hosts with a bandwidth of 150 Mbits/sec

B. a route through two intermediary hosts with a bandwidth of 100 Mbits/sec

C. a route through two intermediary hosts with a bandwidth of 10 Gbits/sec

D. a route through one intermediary host with a bandwidth of 10 Mbits/sec

Answer: D
QUESTION NO: 305

If JumpStart clients are on a different subnet to the DHCP server, what must be configured to enable
them to communicate with the DHCP server?

A. a BOOTP relay

B. a boot server on the same network as the DHCP server

C. DNS server on their network

D. a firewall to perform NAT for the JumpStart client

Answer: A

QUESTION NO: 306

Which three network techniques use a ring topology? (Choose three.)

A. Ethernet

B. CDDI

C. ATM

D. FDDI

E. Token Bus

F. Token Ring

Answer: B,D,F
QUESTION NO: 307

Which is the only DHCP lease type that allows for an IP address to be leased for a finite period of time?

A. static

B. automatic

C. bootp

D. dynamic

E. manual

Answer: D

QUESTION NO: 308

A network administrator has several clients unable to generate ARP requests, and the administrator
decides it is safe to use IP addresses assigned by DHCP servers.

What should the network administrator do to ensure that DHCP clients' dhcpagent daemons will accept
an IP address even though they are unable to generate an ARP request?

A. modify DHCP clients and disable RARP

B. set the IGNORE_FAILED_ARP variable to no

C. set the IGNORE_FAILED_ARP variable to yes

D. ensure that the client interface is set to NOARP

Answer: C
QUESTION NO: 309 DRAG DROP

Click the Task button.

Place each LAN component next to its description.

Answer: <m x1="96" x2="176" y1="229" y2="261" ss="0" a="0"></m><m x1="185" x2="265" y1="229"
y2="260" ss="0" a="1"></m><m x1="271" x2="354" y1="228" y2="260" ss="0" a="2"></m><m x1="16"
x2="96" y1="68" y2="100" ss="1" a="0"></m><m x1="18" x2="96" y1="108" y2="142" ss="1"
a="1"></m><m x1="16" x2="97" y1="148" y2="181" ss="1" a="2"></m><c start="1" stop="0"></c><c
start="2" stop="1"></c><c start="0" stop="2"></c>

QUESTION NO: 310

In the five-layer TCP/IP model, which two functions does the Network Interface Layer provide? (Choose
two.)

A. data addressing between networks

B. connections between applications

C. packet framing

D. Cyclic Redundancy Checking

Answer: C,D

QUESTION NO: 311

A system boots and has a configured network interface. At minimum, what type of route is
automatically added to the routing table?

A. dynamic indirect

B. static indirect

C. dynamic direct

D. static direct

Answer: D

QUESTION NO: 312

An application must use a connection-oriented protocol to transfer data. Which statement about this
method of data transfer is true?

A. Transmission of data can begin only when the remote server sends an initial acknowledgment.

B. Transmission of data can begin only when packet transit time has been established.

C. Transmission of data can begin only when the ARP reply packet size has been renegotiated.
D. Transmission of data can begin only when the routing vector has been minimized.

Answer: A

QUESTION NO: 313

When must a local host try to route through an intermediary host to reach a remote host?

A. when the routing table on the local host has been updated by RIP

B. when the network address of the remote host differs from the network address of the local host

C. when the local host IP address was obtained using RARP

D. when the remote host is NOT in the ARP cache

Answer: B

QUESTION NO: 314

Which protocol is the predecessor of DHCP?

A. RARP

B. bootparam

C. BOOTP

D. TFTP

E. ARP
Answer: C

QUESTION NO: 315

In the five-layer TCP/IP model, which two functions does the Internet Layer provide? (Choose two.)

A. routing

B. data fragmentation

C. Cyclic Redundancy Checking

D. physical connections

E. data representation

Answer: A,B

QUESTION NO: 316 DRAG DROP

Click the Task button.

Place each component of an Ethernet-II frame on its corresponding position in the frame.
Answer: <m x1="6" x2="110" y1="45" y2="84" ss="0" a="0"></m><m x1="119" x2="222" y1="45"
y2="84" ss="0" a="1"></m><m x1="232" x2="334" y1="45" y2="83" ss="0" a="2"></m><m x1="344"
x2="446" y1="44" y2="83" ss="0" a="3"></m><m x1="456" x2="559" y1="44" y2="84" ss="0"
a="4"></m><m x1="23" x2="126" y1="133" y2="170" ss="1" a="0"></m><m x1="125" x2="230"
y1="134" y2="170" ss="1" a="1"></m><m x1="231" x2="334" y1="134" y2="171" ss="1" a="2"></m><m
x1="334" x2="437" y1="133" y2="170" ss="1" a="3"></m><m x1="440" x2="543" y1="133" y2="170"
ss="1" a="4"></m><c start="4" stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c
start="1" stop="3"></c><c start="2" stop="4"></c>

QUESTION NO: 317

Given:

host name IP address

myhost 200.54.42.10

printsvr 200.55.42.30

The system myhost needs to send data to printsvr. The routing table on myhost has no entry for
printsvr. The routing table on myhost has no entry for the 200.55.42.0 network.

Which entry does the routing algorithm look for next?

A. 200.54.42.255

B. loopback

C. ARP cache

D. RARP

E. default
Answer: E

QUESTION NO: 318 DRAG DROP

Click the Task button.

When investigating tunneling, you decide to use snoop to examine the way header and encapsulation
works. You ping the destination address of the tunnel and get a successful reply. In the snoop output
you discover these protocols:

ICMPv6

ETHER

IPv6

IPv4

Place the protocol types in the order of encapsulation in which they would be observed in the snoop
output.

Note: Box 1 should contain the outermost protocol in terms of encapsulation, and Box 4 should contain
the innermost encapsulated protocol.
Answer: <m x1="12" x2="83" y1="27" y2="72" ss="0" a="0"></m><m x1="92" x2="164" y1="25"
y2="72" ss="0" a="1"></m><m x1="172" x2="244" y1="26" y2="74" ss="0" a="2"></m><m x1="253"
x2="324" y1="27" y2="74" ss="0" a="3"></m><m x1="12" x2="83" y1="132" y2="177" ss="1"
a="0"></m><m x1="92" x2="164" y1="130" y2="177" ss="1" a="1"></m><m x1="173" x2="241"
y1="129" y2="177" ss="1" a="2"></m><m x1="253" x2="324" y1="130" y2="179" ss="1" a="3"></m><c
start="1" stop="0"></c><c start="3" stop="1"></c><c start="0" stop="2"></c><c start="2"
stop="3"></c>

QUESTION NO: 319

You have created an IPv6 tunnel between two hosts. Which two statements are true about tunnelling?
(Choose two.)

A. IPv6 Solaris tunnelling always involves an IP datagram encapsulating an IP datagram.

B. Tunnelled traffic is always TCP or UDP in IPv6.

C. Tunnelled traffic is always encrypted.

D. The IP header of the datagram that has encapsulated the tunnelled data contains the source address
of the tunnel.

E. The tunnel source IP address is always the same as the source IP address in the IP header of the
tunnelled (encapsulated) IP datagram.

Answer: A,D

QUESTION NO: 320

You have used the appropriate startup script in /etc/init.d to start the NTP daemon. However, the NTP
daemon does not start up. There is no error message. What is the reason for this?
A. There is no configuration file.

B. rpcbind is not running on the machine.

C. The NTP daemon cannot contact an NTP server.

D. The configuration file contains faulty entries.

Answer: A