Scribd
Upload
29 views

CH 1612

QPSK (Quadrature Phase Shift Keying) is a digital modulation technique that encodes 2 bits per symbol by changing the phase of a carrier wave by 0, 90, 180, or 270 degrees. QPSK modulation is achieved by varying the phase of sine and cosine basis functions depending on the message symbols. For demodulation, the received QPSK signal is multiplied by reference sine and cosine waves and integrated over one bit period before detection to recover the transmitted bits.

Uploaded by

Kylle Bryan Ferrer
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
29 views

CH 1612

QPSK (Quadrature Phase Shift Keying) is a digital modulation technique that encodes 2 bits per symbol by changing the phase of a carrier wave by 0, 90, 180, or 270 degrees. QPSK modulation is achieved by varying the phase of sine and cosine basis functions depending on the message symbols. For demodulation, the received QPSK signal is multiplied by reference sine and cosine waves and integrated over one bit period before detection to recover the transmitted bits.

Uploaded by

Kylle Bryan Ferrer
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

CHAPTER 16

QUADRATURE PHASE SHIFT KEYING

Quadrature Phase Shift Keying (QPSK) is a method to transmit digital information on a


carrier by changing the phase of the carrier. In QPSK there are 4 different phase changes defined,
each phase change represents the transmission of 2 bits.

QPSK Modulation

In digital modulation techniques a set of basis functions are chosen for a particular
modulation scheme.Generally the basis functions are orthogonal to each other. Basis functions
can be derived using ‘Gram Schmidt orthogonalization’ procedure.Once the basis function are
chosen, any vector in the signal space can be represented as a linear combination of the basis
functions. In Quadrature Phase Shift Keying (QPSK) two sinusoids (sin and cos) are taken as
basis functions for modulation. Modulation is achieved by varying the phase of the basis
functions depending on the message symbols. In QPSK, modulation is symbol based,where one
symbol contains 2 bits. The following equation outlines QPSK modulation technique.

sin(t)=2EsT−−−−√cos(2πfct+(2n−1)π4),n=1,2,3,4

When n=1, the phase shift is 45 degrees. This is called pi/4 QPSK.The constellation diagram
of QPSK will show the constellation points lying on both x and y axes.This means that the QPSK
modulated signal will have an in-phase component (I) and also a quadrature component (Q). This
is because it has only two basis functions.

A QPSK modulator can be implemented as follows. A demultiplexer (or serial to parallel


converter) is used to separate odd and even bits from the generated information bits. Each of the
odd bits (quadrature arm) and even bits (in-phase arm) are converted to NRZ format in a parallel
manner.

The signal on the in-phase arm is multiplied by cosine component and the signal on the
quadrature arm is multiplied by sine component. QPSK modulated signal is obtained by adding
the signal from both in-phase and quadrature arm.
QPSK Demodulation:

For QPSK demodulator , a coherent demodulator is taken as an example. In coherent


detection technique the knowledge of the carrier frequency and phase must be known to the
receiver. This can be achieved by using a PLL (phase lock loop) at the receiver. A PLL
essentially locks to the incoming carrier frequency and tracks the variations in frequency and
phase. For the following simulation , a PLL is not used but instead we simple use the output of
the PLL.

For demonstration purposes we simply assume that the carrier phase recovery is done and
simply use the generated reference frequencies at the receiver (cos(ωt)) and (sin(ωt)).

In the demodulator the received signal is multiplied by a reference frequency generators


(cos(ωt)) and (sin(ωt)) on separate arms (in-phase and quadrature arms). The multiplied output on
each arm is integrated over one bit period using an integrator. A threshold detector makes a
decision on each integrated bit based on a threshold. Finally the bits on the in-phase arm (even
bits) and on the quadrature arm (odd bits) are remapped to form detected information stream.
Detector for in-phase arm is shown below. For quadrature arm the below architecture remains
same but sin(ωt) basis function must be used instead

You might also like