Scribd
Upload
519 views

Tapping Parameters

1) To calculate the feed rate of a machine when tapping, you need the thread pitch (P) and revolutions per minute (RPM). 2) The feed per revolution (f) is equal to the thread pitch (P). 3) As an example, for a M12 x 1.75 thread tapped at 186 RPM, the feed rate is 325.5 mm/min or 0.325 m/min.

Uploaded by

Vlastimir Pejić
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
519 views

Tapping Parameters

1) To calculate the feed rate of a machine when tapping, you need the thread pitch (P) and revolutions per minute (RPM). 2) The feed per revolution (f) is equal to the thread pitch (P). 3) As an example, for a M12 x 1.75 thread tapped at 186 RPM, the feed rate is 325.5 mm/min or 0.325 m/min.

Uploaded by

Vlastimir Pejić
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Bag full of wisdom when you are in trouble

No. 009
How to set the feed rate for the machine when tapping How to use

【Question】
How can I calculate the feed rate of a machine
using the following tap?

-Spiral fluted tap M12 X 1.75

-Using the recommended cutting speed of 7m/min (23 SFM).

【Answer】
It's easy if you know the thread pitch (P) and the recommended
Revolutions Per Minute (RPM).

Feed per revolution = f


Revolutions per minute
(RPM) = n

Pitch of the taps thread = P


Meters Per Minute (MPM) feed rate = Vf

Using the example of 186 revolutions per minute


(RPM) we can calculate the Meters Per Minute
(MPM) of feed rate of the machine. (see YES-008
for details)
Vf = n X f Tap: M12 X 1.75

Vf: Feed rate of the machine in MPM Cutting speed: 7m/min

n: Revolutions per minute (RPM) The feed per revolution (f) is the same as the pitch
of the taps thread on a single start thread. On a
f : Feed per revolution in mm double start thread the feed per revolution is 2
times the thread pitch. On a 3 start thread the feed
is 3 times the thread pitch and so on.

Example: the machine feed rate (Vf) of a single start M12 X 1.75 thread
ran at 186 revolutions per minute (RPM) is calculated as follows;

Vf = 186 RPM X 1.75mm Thread Pitch = 325.5mm per minute feed rate
millimeters per minute (mmpm).

325.5 ÷ 1,000 = .325 feed rate in Meters Per Minute (MPM).


YES-009
How to set the feed rate for the machine when tapping How to use

When calculating a metric screw thread, the thread pitch measurement is taken
from a point of the thread to the same point of the next adjacent thread.

When calculating Unified inch screw threads, Whitworth screw threads or pipe
threads the measurement of the thread pitch is measured by dividing 1.000" by
the threads per inch (TPI). This calculation will yield the distance from a point on
a thread to the same point on the next adjacent thread in inches.

Example: 1/2"-13UNC Pitch size = 1.000" ÷ 13 TPI (P ) = 0.0769" or 1.954mm.


　　
Diameter conversion = 1/2" ÷ 1mm (.03937) = 12.7mm Diameter

Recommended cutting speed in meters per minute (Vc) =7 m/min

Machine spindle speed in RPM (n) = (1000 X 7MPM) ÷ (3.14 X 12.7mm) = 175
revolutions per minute (RPM) 1,000 * Vc
n=
π * Dc

The feed rate of the machine for a 1/2"-13 TPI tap = 1.954mm X 175 RPM =
341.95mm per minute = .342 Meters Per Minute feed rate.

You might also like