Scribd
Upload
145 views

Two Way Slab Design According To EN1992-1-1 AN: Uhaveafter Installation

This document provides the inputs and calculations for a two-way slab design according to Eurocode 2. It includes the slab dimensions, material properties, loads, and design checks. The calculations determine the bending moments, shear forces, and required reinforcement for the slab. The results indicate the required reinforcement areas meet the minimum requirements of Eurocode 2.

Uploaded by

SES DESIGN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
145 views

Two Way Slab Design According To EN1992-1-1 AN: Uhaveafter Installation

This document provides the inputs and calculations for a two-way slab design according to Eurocode 2. It includes the slab dimensions, material properties, loads, and design checks. The calculations determine the bending moments, shear forces, and required reinforcement for the slab. The results indicate the required reinforcement areas meet the minimum requirements of Eurocode 2.

Uploaded by

SES DESIGN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Two way slab design according to EN1992-1-1 AN v1.

13
Ref: Henry Thonier tome 7, Maîtrise EC2 & Projet Béton Armé 2011, R.P The author
a2 will not responsible
Inputs factor: 0.50 0.29 t.m for any uses of
short span Lx= 4.00 m between edges fck= 25 Mpa l1 0.80 0.96 cm2 this program
long span Ly= 0.20 m between edges fyk= 390 Mpa
Ly
partition walls c= 0.00 t/m2 slab thickness= 0.12 m Ma4= 0.29 0.29 t.m
dead load r= 0.150 t/m2 cover of slab= 0.03 m l2= 0.80 l2= 0.80
live load q= 0.250 t/m2 a4 0.50 a3= 0.50

Lx
self-weigth pp= 1 1: taking into account by défault, 0: non Strinkage: 1 1: yes Aa4= 0.96 0.96 cm2
ϕ= 0 value >= 2 (0=auto) (défault=1) 0: non
Design uhaveafter installation
α=Lx/Ly= 20.000 >0.5 a1
α1=Q/(G+Q)= 0.357 factor: 0.50 0.29 t.m
poids propre pp = 2.5t/m3*h= 0.30 t/m2 l1= 0.8 0.96 cm2
ELSqpm= charge qp en ELSqpm= 0.53 t/m2
ELU= charge en ELU= 0.983 t/m2 Mt//x 0.43 1.54 cm2
Lx at support= 4.00 m Mt//y 0.43 1.45 cm2
ELU v=0 ELS v=0.2 fck= 1667 t/m2
Lx/Ly ux uy ux uy fyk= 3.39 t/cm2
α maxi maxi maxi maxi d= 0.09 m
20 0.037 1 0.04 1
ELU ELSqpm Vux=q*L/(2+α)= 0.18 t/m *Ref: Béton Armé Element Simple EC2
Mox= ux*p*Lx^2=0.578 0.37 tm/m Vuy=q*L/3= 1.31 t/m
Moy= uy*Mox= 0.578 0.37 tm/m τu= 0.02 Mpa
1.97 1.05 τu lim EC AN= 1.13 Mpa τ lim=[0.34*sqrt(fck)/ϒb] (Ref: Jean Marie Paillé p186)
OK
ELU ELSqpm αu z (m)
Max1= 0.50 Mox 0.289 0.186 tm/m 0.03 0.089025 Aax1= 0.96 cm2/m Results S4
Max2= 0.50 Mox 0.289 0.186 tm/m 0.03 0.089025 Aax2= 0.96 cm2/m rebars
Mtx= 0.750 Mox 0.43 0.28 tm/m 0.04 0.09 Atx= 1.54 cm2/m Atx= 5.27 cm2/m OK
Asmini EC2= 1.54 cm2/m EC2 1/250 1/500 R.P*
BAEL= -6.12 cm2/m f cal= -0.178 -0.130 -0.203 cm
ELU ELSqpm Treillis= ST20 -1.600 -0.800 -0.800 cm
May3= 0.50 Mox 0.289 0.186 tm/m 0.03 0.089025 Aay3= 0.96 cm2/m check OK OK OK
May4= 0.50 Mox 0.289 0.186 tm/m 0.03 0.089025 Aay4= 0.96 cm2/m *Professional Strandard of French
Mty= 0.750 Moy* 0.43 0.28 tm/m 0.04 0.09 Aty= 1.45 cm2/m Aty= 7.53 cm2/m OK
Asmini= 0.38 cm2/m

12/8/2017

You might also like