Scribd
Upload
42 views

EXP - 1-Mobile Wireless Propagation Models and Path Loss Estimation

This document discusses mobile wireless propagation models and path loss estimation. It introduces radio frequency propagation in multipath environments and how the transmission path between transmitter and receiver varies randomly. It focuses on how changing system parameters other than transmit power, such as carrier frequency and distance, can increase the separation distance between transmitter and receiver to expand cell coverage. The document presents generic and free-space propagation models and equations for path loss as a function of distance. It then describes a simulation experimental procedure to analyze path loss versus distance using the free-space model for different carrier frequencies.

Uploaded by

Mohamd barca
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
42 views

EXP - 1-Mobile Wireless Propagation Models and Path Loss Estimation

This document discusses mobile wireless propagation models and path loss estimation. It introduces radio frequency propagation in multipath environments and how the transmission path between transmitter and receiver varies randomly. It focuses on how changing system parameters other than transmit power, such as carrier frequency and distance, can increase the separation distance between transmitter and receiver to expand cell coverage. The document presents generic and free-space propagation models and equations for path loss as a function of distance. It then describes a simulation experimental procedure to analyze path loss versus distance using the free-space model for different carrier frequencies.

Uploaded by

Mohamd barca
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

EXP -1-

Mobile Wireless Propagation Models and Path Loss


Estimation
1.1 Introduction
Radio-frequency propagation is fuzzy in nature in multipath environments
because of irregular terrain, RF barriers, and scattering phenomena. The
performance of mobile communication systems is limited by the radio
channel, and the transmission path between transmitter and receiver varies
randomly from simple line of sight (LOS) to one obstructed severely by
building and foliage [3]. Most cellular radio system operates in urban
environment there is no direct wave at the receiver. Rather, an integrated wave
resulting from diffraction, reflection, and scattering from various obstacles
(buildings, moving objects, etc.).

Propagation models traditionally focus on the prediction of signal strength at


the receiver, and distance (d) between transmitter and receiver plays the most
critical role on the received signal strength. Figure 1.1 illustrates a typical
point-to-point mobile wireless communication system. A very common thing
that could come in mind is what would be the distance d that can provide good
received signal quality, and the relevant factors that influence largely to
increase d the longest possible so as to increase cell coverage and
consequently cost from investment. The simplistic answer is to increase
transmit power. However, increasing transmit power causes additional
interference such as intra-cell interference, inter-cell interference.
In this experiment, we focus on changes in the system parameters (other than
transmit power) that result in increasing separation distance d, i.e. cell
coverage. Figure 1.2 illustrates these parameters in the system. We will
primarily carry out the impact of carrier frequency f (MHz) and distance d
(km) on path loss. In addition, sensitivity analysis that provides critical
parameters in the system with most impact on d is incorporated for the system
design and planning purpose.
1.2 System Model
1.2.1 Generic model
A generic Radio Frequency (RF) transmission system is already shown in
Figure 1.1. The transmit power is given by Equation 1.1.

Where, the symbols represent as follows.


Pt is the transmit power (consider from the base station (BS)),
Pr is the receive power (at the mobile station (MS)),
Gt is the total antenna gain experiences by the signal, and
LT is the total loss experiences by the signal.
Hence, rearranging Equation 1.1, path loss between BS and MS is given by

1.2.2 Free-space model


Free-space model is the simplest path loss model that takes only frequency (f)
and distance (d) into account. In free-space (no obstacles and atmospheric
effects) propagation, the path loss is given by

Where, Pr represents receive power,


Pt represents transmit power,
Gt and Gr represent gain of transmitter and receiver respectively, and
d is the distance between transmitter and receiver.

Equation 1.3 can be rewritten as follows for path loss

Hence, putting the value of LT-FS in Equation 1.1 and solving for d will
provide with the maximum distance between transmitter and receiver as
follows.

1.3 Simulation Experimental Procedure


1.3.1 Set values to simulation variables for path loss models as follows.
Free-space model:
Carrier frequency, f (MHz) = 900 and 1800,
Transmit power Pt = 39 dBm,
Cable loss Lc= 4 dB (total),
Antenna gain Gt =28 dBi (total).
1.3.2 Simulation Algorithm
1. Path loss versus distance (cell coverage)
Step 1 define variables;
Step 2 set values for dmax , f(MHz), Pt , Lc , Gt , hb, hm, a(hm), B;
Step 3 define path loss expressions for Free-space
Step 4 repeat step 2 up to d=dmax ;
Step 5 plot distance versus path losses.
REPORT
Plot the received signal power Pr as a function of distance (similar to Question
01). Assume transmit power Pt = 39 dBm, total antenna gain Gt = 28 dBi (14
dBi for each antenna: Tx and Rx), total cable loss Lc = 4 dB (2 dB at each
side; Tx and Rx). Hint: use Equation 1.1.

You might also like