Scribd
Upload
157 views

4-Bit Electronic Clock DIY Kit: NO. Parameter Value

This document summarizes an electronic clock DIY kit that contains: - An AT89C2051 microcontroller as the core component along with 16 other electronic parts. - It functions as a dual alarm clock and displays time in hours:minutes or minutes:seconds format. - The kit allows the user to set the time, turn on/off alarms, and set alarm times through a menu system accessed by pressing buttons. - Assembly instructions are provided to guide the user in installing the electronic components onto the PCB board according to the schematic diagram.

Uploaded by

juan carlos hincapie cardona
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
157 views

4-Bit Electronic Clock DIY Kit: NO. Parameter Value

This document summarizes an electronic clock DIY kit that contains: - An AT89C2051 microcontroller as the core component along with 16 other electronic parts. - It functions as a dual alarm clock and displays time in hours:minutes or minutes:seconds format. - The kit allows the user to set the time, turn on/off alarms, and set alarm times through a menu system accessed by pressing buttons. - Assembly instructions are provided to guide the user in installing the electronic components onto the PCB board according to the schematic diagram.

Uploaded by

juan carlos hincapie cardona
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

www.icstation.

com

4-Bit Electronic Clock DIY Kit

1. Introduction
YSZ-4 four electronic clock, it takes AT89C2051 as its core, a total of 16 electronic

components to come true the two channels of the alarm clock, (8:00-20:00) on time

alarm ,accurate adjustment , and other functions.

2. Parameter
NO. Parameter Value

1 Operating voltage DC 3V-6V

2 PCB board material RF-4

3 Size 52mm*42mm

3. Principle
The whole system by MCU minimum system, key input circuit, display circuit,

buzzer circuit and power supply parts.

1>. MCU minimum system: including the U1 (AT89C2051), C1, R1 for power on

reset circuit .Clock circuit is composed of C2， C3 and Y1.

2>. The pressed key input circuit：composed of S1, S2, short press the button

once a loud buzzer rang, long press the button once two loud buzzer rang.

3>. The display circuit：4bits common cathode and on PR1 Resisters Packs .

4>. Buzzer circuit：composed of Q1, R2 and LS1, short press the button once a

loud buzzer rang, long press the button once two loud buzzer rang.

5>. J1 is 5v power supply input terminal, C4 filtering.

4. Operation instruction
It will display 12:59 when Power-on，while is normal interface("hours:minutes").

1
www.icstation.com

The both channels of alarm clock are opened.At the same time,the first alarm clock
has been set at 13:01.the second alarm clock has been set at 13:02.
After power on ,short press S2.The display of digital tube will switch between
"hours:minutes" and "minutes:seconds";Long press S1 to enter the system Settings
menu. there are A, B, C, D, E, F, G, H, I submenu. Short press S1 sub-menu plus
increase by degrees。finally back to the normal interface

A Sub menu : Correction for hours


Display data will add 1 after press S2.after adjusted the A Submenu,then short
press S2 to save the adjusted results and quit A submenu,enter B sbumenu

B Sub menu : Correction for minutes


Display data will add 1 after press S2.after adjusted the B Submenu,then short
press S2 to save the adjusted results and quit B submenu,enter C sbumenu

C Sub menu:on time alarm switch


The default state is ON (on-time-alarm is open from 8:00 to 20:00)
It will switch between ON and OFF(on-time-alarm is closed) when press S2.
Short press S2 to save the adjusted results and quit C submenu,enterD sbumenu

D Sub menu:The first alarm-clock switch


The default state is ON (the first alarm-clock is opened)
It will switch between ON and OFF(first-alarm-clock is closed) when press S2。
If set to ON, short press S1 to save and quit,then enter E submenu;
If set to OFF, short press S1 to save and quit ,then enter G submenu;

E Sub menu:The first alarm clock set for hours


Display data will add 1 after press S2.after adjusted the E Submenu,then short
press S2 to save the adjusted results and quit E submenu,enter F sbumenu

F Sub menu:The first alarm clock set for minutes


Display data will add 1 after press S2.after adjusted the F Submenu,then short
press S2 to save the adjusted results and quit F submenu,enter G sbumenu

G Sub menu:The Second alarm-clock switch


The default state is ON (the second alarm-clock is opened)
It will switch between ON and OFF(second-alarm-clock is closed) when press
S2。
If set to ON, short press S1 to save and quit ，then enter H submenu;
If set to OFF, short press S1 to save and quit ，then enter normal interface;

H Sub menu:The second alarm clock set for hours


Display data will add 1 after press S2.after adjusted the F Submenu,then short
press S2 to save the adjusted results and quit H submenu,enter I sbumenu

2
www.icstation.com

I Sub menu:The second alarm clock set for hours


Display data will add 1 after press S2.after adjusted the I Submenu,then short
press S2 to save the adjusted results and quit H submenu, then enter normal interface.

Second correction:
Short press S2 in the normal interface,then enter "minutes : seconds"
interface .Long press S2,make the second zero.Then short press S2 twice enter normal
interface

5. Schematic

Note: there is direction for PR1 Resisters Packs , there is one side of the word in

the direction of the MCU.Pay an attention!!!

6. Component listing
NO. Component Name PCB Marker Parameter QTY
1 Metal Film Resistor R1,R2 10K 2
2 Ceramic Capacitor C2,C3 30pf 2
3 Ceramic Capacitor C4 0.1uf 104 1

3
www.icstation.com

4 Electrolytic Capacitor C1 10uF/25V 1


5 Network Resistor PR1 1K 1
6 Crystal Oscillator Y1 12MHz 1
7 S8550 Q1 TO-92 1
8 Button S1,S2 6*6*5mm 2
9 AT89C2051 U1 DIP-20 1
10 IC Socket U1 DIP-20 1
11 Active Buzzer LS1 5V 1
12 Digital Tube DS1 4Bit Red 1
13 DC Socket J1 3.5mm 1
14 Power Cable USB to 3.5mm 1

NOTE:Users can complete the installation by PCB silk screen and

component listing

7. Installation Steps
Step 1:Install 2pcs Resistor,3pcs ceramic capacitor,1pcs Crystal Oscillator

4
www.icstation.com

Step 2:Install 1pcs Network Resistor.Pay attention to the installation

direction.

Step 3:Install IC Socket.But pay attention to the installation direction.

5
www.icstation.com

Step 4: Install 2pcs button.But pay attention to the installation

direction.Install 1pcs S8850.

6
www.icstation.com

Step 5: Install 1pcs Power socket;1pcs Electrolytic Capacitor;1pcs

Buzzer.

7
www.icstation.com

Step 6: Install 4Bit Digital Tube and IC.And then test!

8
www.icstation.com

8.Effect demonstration(Only for appreciation)

9
www.icstation.com

10
www.icstation.com

11

You might also like