STPS1045B

Power Schottky rectifier

Datasheet  production data

Description
High voltage Schottky rectifier suited for switch
mode power supply and other power converters.
$
. Packaged in DPAK, this device is intended for use
$ in high frequency circuitries where low switching
losses is required.
.
.
Table 1. Device summary
Symbol Value
$
$ IF(AV) 10 A
$
$ VRRM 45 V
Tj 175 °C
'3$.
VF(typ) 0.50 V

Features
 Very small conduction losses
 Extremely fast switching
 Low thermal resistance
 Negligible switching losses
 Low forward voltage drop
 Low capacitance
 Avalanche specification
 ECOPACK®2 compliant component for DPAK
on demand

October 2016 DocID6085 Rev 9 1/8

This is information on a product in full production. www.st.com 8
Characteristics STPS1045B

1 Characteristics

Table 2. Absolute ratings (limiting values, at 25 °C unless otherwise stated)

Symbol Parameter Value Unit

VRRM Repetitive peak reverse voltage 45 V

IF(RMS) / pin Forward rms current 7 A
Average forward current,
IF(AV) Tc = 150 °C 10 A
δ 0.5, square wave
IFSM Surge non repetitive forward current tp = 10 ms sinusoidal 75 A
PARM Repetitive peak avalanche power tp = 10 s, Tj = 125 °C 285 W
Tstg Storage temperature range -65 to +175 °C
Tj Maximum operating junction temperature(1) 175 °C
dPtot < 1
1. condition to avoid thermal runaway for a diode on its own heatsink
dTj Rth(j-a)

Table 3. Thermal resistance

Symbol Parameter Max. value Unit

Rth(j-c) Junction to case 3 °C/W

Table 4. Static electrical characteristics

Symbol Parameter Test conditions Min. Typ. Max. Unit

Tj = 25 °C - 100 A
IR (1) Reverse leakage current VR = VRRM
Tj = 125 °C - 7 15 mA
Tj = 25 °C - 0.63
IF = 10 A
Tj = 125 °C - 0.50 0.57
VF(2) Forward voltage drop V
Tj = 25 °C - 0.84
IF = 20 A
Tj = 125 °C - 0.65 0.72
1. Pulse test: tp = 5 ms,  < 2%
2. Pulse test: tp = 380 µs,  < 2%

To evaluate the conduction losses, use the following equation:

P = 0.42 x IF(AV) + 0.015 x IF2(RMS)

2/8 DocID6085 Rev 9

STPS1045B Characteristics

Figure 1. Average forward power dissipation Figure 2. Average forward current versus
versus average forward current ambient temperature (δ= 0.5)

3)$9 : ,)$9 $
 
į  į  į  į 
5WKMD 5WKMF





į 
5WKMD ƒ&:
 



 7
5WKMD ƒ&:


į WS7 WS
 
                    

, )$9 $ 7DPEƒ&

Figure 3. Normalized avalanche power derating Figure 4. Relative variation of thermal

versus pulse duration at Tj = 125 °C impedance junction to case versus pulse
duration
3$50 W S  = WKMF 5WKMF
3$50 —V 




  į 


į 
 7
 į 

į W 37 W3
6LQJOHSXOVH

 (  (  (  (  ( 
   
W S —V WSV

Figure 5. Reverse leakage current versus Figure 6. Junction capacitance versus reverse
reverse voltage applied (typical values) voltage applied (typical values)
,5—$
&S)
( 
) 0+]
7M ƒ& 926& P9506
( 7M ƒ&
7M ƒ&

7M ƒ&

(

7M ƒ&
(
7M ƒ&

(
7M ƒ& 

(

( 

         

959 959

DocID6085 Rev 9 3/8

Characteristics STPS1045B

Figure 7. Forward voltage drop versus forward Figure 8. Thermal resistance junction to
current ambient versus copper surface under tab
, ) $
 5WKMDƒ&:
7M ƒ& 
PD[LPXPYDOXHV
(SR[\SULQWHGERDUG)5FRSSHUWKLFNQHVV —P '3$.

7M ƒ& 
W\SLFDOYDOXHV
 


7M ƒ& 
PD[LPXPYDOXHV






 
         
9 ) 9 6FXFPð

4/8 DocID6085 Rev 9

STPS1045B Package Information

2 Package Information

 Epoxy meets UL94,V0

 Cooling method: by conduction (C)
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.

2.1 DPAK package information

Figure 9. DPAK package outline

(
$
E
F 7KHUPDOSDG

/ (

'
'
+ 5

/

$
H E 5
H F

$
/
/
9
*DXJH
 SODQH

Note: This package drawing may slightly differ from the physical package. However, all the
specified dimensions are guaranteed.

DocID6085 Rev 9 5/8

Package Information STPS1045B

Table 5. DPAK package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 2.18 2.40 0.085 0.094

A1 0.90 1.10 0.035 0.043
A2 0.03 0.23 0.001 0.009
b 0.64 0.90 0.025 0.035
b4 4.95 5.46 0.194 0.214
c 0.46 0.61 0.018 0.024
c2 0.46 0.60 0.018 0.023
D 5.97 6.22 0.235 0.244
D1 4.95 5.60 0.194 0.220
E 6.35 6.73 0.250 0.264
E1 4.32 5.50 0.170 0.216
e 2.28 0.090
e1 4.40 4.70 0.173 0.185
H 9.35 10.40 0.368 0.409
L 1.00 1.78 0.039 0.070
L2 1.27 0.050
L4 0.60 1.02 0.023 0.040
V2 -8° +8° -8° 8°

Figure 10. DPAK footprint dimensions (in mm)

  

$



% 
7KHGHYLFHPXVWEHSRVLWLRQHGZLWKLQ  $ %

6/8 DocID6085 Rev 9

STPS1045B Ordering information

3 Ordering information

Table 6. Ordering information

Order code Marking Package Weight Base qty Delivery mode

STPS1045B S10 45 75 Tube

DPAK 0.30 g
STPS1045B-TR S10 45 2500 Tape and reel

4 Revision history

Table 7. Document revision history

Date Revision Changes

Jul-2003 3B Last issue

21-Apr-2005 4 IPAK package removed
03-Nov-2005 5 DPAK foot print dimensions updated.
01-Jul-2010 6 Updated Figure 10 Updated ECOPACK statement.
Updated DPAK package information, Table 2 and
04-Nov-2014 7
Figure 5. Removed PARM (Tj = 25 °C).
Updated Table 2.
07-Apr-2015 8
Format update to current standard.
05-Oct-2016 9 Updated DPAK package information.

DocID6085 Rev 9 7/8

 STPS1045B

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2016 STMicroelectronics – All rights reserved

8/8 DocID6085 Rev 9